Search Documents

By H. Oterdoom, S. Pilger, T. P. Bui, J. Rotarius

"Most FeNi furnaces used to rely on post-combustion and off-gas cooling inside the furnace to eliminate the produced CO gas, and control the off gas temperature. As furnace load, capacity, and thus gas volumes increased over the years, this led to increased instabilities that can cause problems in controlling the operation. Some of the large capacity furnaces nowadays work with partial or full combustion outside the furnace, more similar to the steel industry. Forced combustion with or without enriched air and other additions can support in controlling post-combustion, stabilizing and even reducing off gas amounts, and affecting composition. This paper presents some of the possibilities and advantages of having a specially designed post-combustion system for the FeNi laterite industry, but that could also be applied to other processes as well.Large Scale Furnaces In the FeNi industry, the Rotary Kiln Electric Furnace (RKEF) process is still going strong in spite of continuous hope that hydrometallurgical processes will one day make the RKEF plant obsolete. Within the pyrometallurgical plants there is a continuous trend for larger scale furnaces. The development for a number of furnaces that were started before 1985 and increased capacity by “natural growth” is given in Figure 1. Natural growth refers to the development of the plants that after having mastered a certain level of operation, were ready for a higher load that could be installed either with a new furnace on the same site, or during a revamp. The advantages of natural growth are numerous, for example: •,Deep knowledge of the ore and its’ behavior, no need for testing, and little risk of surprises. •,Mining, laboratory, equipment, etc. is all proven technology for the conditions on site. •,Starting a furnace with increased capacity is a re-start, not a green-field commissioning. •,Typically, when increasing the production capacity of an existing plant, not the entire plant is commissioned for the first time, but only a part. In the FeNi laterite industry for example, the kilns may already have had the capacity to provide enough material."

Jan 1, 2017

By S. Schade, G. Möllemann, C. Niestroj

"Mining environments, whether open-pit or underground, pose difficult conditions for any sensor system. However, the ever-increasing need for automation requires the application and use of sensor systems in order to gather relevant information required for process automation. Ultra-Wideband radio (UWB) is a robust technology well-suited for underground applications. These applications include positioning and communication. This paper introduces UWB and presents results from measurement campaigns in harsh environments. Using filtering and sensor fusion precise and robust positioning can be achieved even in confinements of underground mining environments. INTRODUCTION Indoor positioning systems (IPS) are gaining ever more importance. Especially in light of ongoing efforts to reach the goals of what was coined as Industry 4.0 by the German government, the development of IPS is inevitable. According to a recent report about the “Global Indoor Location Market Outlook 2019” a growth from $ 597 million in 2014 to $ 3961.8 million by 2019 is expected [1]. Hence, there is also an economic incentive to pursue this topic. The mining industry is profiting from this development as well, since IPS are the basis for the automation of especially mobile mining equipment. Ideally, indoor positioning systems offer to position the equipment continuously and, what’s more, even in real-time [2]. Different approaches are available for IPS. The difference of these systems lie in terms of accuracy, cost, precision, technology, scalability, robustness and security. [3] At the Institute of Advanced Mining Technologies (AMT) of RWTH Aachen University, research suggests that one of the more auspicious approaches for IPS in the mining sector is the employment of ultra-wideband (UWB) radio technology. Because of this, there has been ongoing research into the best way to introduce UWB technology for the application in underground environments. The research started with an indoor positioning application, which only consisted of the UWB system. In the course of this, different algorithms were developed to enhance the system’s performance for the use in the mining industry. This led to the idea of sensor fusion in which the information of the UWB system are combined with infrastructure-independent technologies like inertial navigation systems (INS) and image-based technologies."

Jan 1, 2017

By R. Venugopal, V. K. Saxena, S. K. Tripathy

"This study was carried out to understand the impact of variation in material morphology on the efficacy of microwave pretreatment. Three different types of mineral matter – coal, iron ore and manganese ore – were treated with microwaves at different energy levels, from 180 to 900 W, for different time durations of one to five minutes. The treated samples were subjected to microscopic, milling and liberation studies. Coal is a porous and amorphous material with low dielectric constant, and grinding of the microwave-pretreated coal samples resulted in an 18.18 percent reduction in the 80 percent of passing particle size, or d80, and a 17.1 percent increase in carbon recovery. The microwave-pretreated soft and friable manganese ore samples showed a 47.82 percent reduction in d80 during grinding and higher manganese recovery of 42.46 percent during liberation analysis. The microwave pretreatment and milling of hard and banded iron ore reduced the d80 by 20.83 percent, but no improvement was observed in mineral liberation. Coal showed better results during treatment at lower energy levels of 180 W for one to three minutes, whereas the minerals needed higher energy of 900 W for five minutes. Particle size analysis indicated rapid size reduction up to an energy input of 25 Wh. This effect diminished with increased energy input.IntroductionComminution is an important unit operation in mineral processing plants for the purposes of size reduction and mineral liberation. But most comminution technologies are energy inefficient and only a small amount of energy is consumed in real size reduction, with the rest wasted. High-grade mineral resources have been exploited on a large scale for the last century, and the upgrading of low-grade resources is now required to fulfill the needs of industry. Pretreatment methodologies for comminution will play a crucial role in the upgrading of low-grade mineral resources. Researchers have studied various pretreatment methods to develop an energy-efficient and techno-economically viable solution to improve mineral liberation and product fineness with minimum energy consumption. Most of these studies were focused on the use of chemical additives, thermal, ultrasonic and microwave treatment, and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Gaete-Garreton, Vargas-Hermandez and Velasquez-Lambert, 2000; Wilson et al., 2006; Kumar et al., 2010; Wang, Shi and Manlapig, 2011; Singh et al., 2012)."

Jan 1, 2017

By M. Javier

"Mining is the main activity that supports civilization. Actual mining presents contradictory concept to the health of the planet. Its business model is linear, fragmented and characterized by inefficiencies in the utilization of water, energy and mineral resources which generate waste and pollution. Before mining begins, it is critical to determine the vulnerability of the ecosystem and after mining, it is critical to determine the depletion of nature. Attending to these vital matters will require quantifying and measuring them. The purpose of this study is to provide and establish the metric to assess the performance and manage a sustainable future for our existence and that of our planet. This index is defined to measure and control Nature Friendly Sustainability (NFS) based on understanding nature. This index will determine the condition of nature constructed on the measurement of physical, chemical and biological equilibrium. Proposing a new mindset for mining design to satisfy nature’s needs would be to offer the same opportunities to future generations. Hence, sustainability is synonymous with equilibrium under a limited ecosystem. Nature is interconnected. Finally, this index of NFS is readable, standardized and relevant to keep nature’s needs in equilibrium. Establishing and NFS index is the next metric for humanity. INTRODUCTION There are a multitude of definitions of what sustainability is. Most of them are defined in terms of the corporate entity from which they emanate. The classical definition of management states that, “if we do not measure it, we cannot manage it.” Management of ecosystems is the definition of sustainability. Indicators of quantity and quality of sustainability are vital in order to create a metric for sustainability. These indicators will measure the depletion and degradation of nature as they occur through human intervention. The first step is to create a metric of sustainability to simplify its definition. The definition of sustainability is based on whether or not you consider nature to be finite or infinite, which is described in Nature Friendly Sustainability (NFS) [1]. The definition of NFS applies to any anthropogenic activity with an understanding of the equivalent activity in nature. That is to say, human activity with nature requires balance and equilibrium in order to be sustainable. The importance of this equilibrium is quantified in a set of metrics in order to establish measurement and acknowledge indicators for our dependence on nature. Sustainability is synonymous with equilibrium in any ecosystem that is limited and fragile. In the graph is the explanation of sustainability definition. See Graph 1"

Jan 1, 2017

By Gavin Yuill, Kameron Ray

"The impact on vibration model accuracy by input data that is inaccurate was previously unknown, butthought to introduce significant error. This paper explores the impact of accuracy of different GPSreceivers, bulk truck density fluctuations, and charge weight location convention on the accuracy of the final vibration model output. GPS accuracy is compared between a professional Differential GPS, a “prosumer” GPS unit and a standard consumer GPS chip commonly found in cell phones. Bulk truck density fluctuations are compared from the density given by the operator and the actual cup density measured in the field. Charge weight locations explored are from the bottom of the blast hole, center of the powder column, and collar of the hole. The findings show that the weakest link in vibration model creation is actually low seismograph accuracy standards. Errors introduced from such are generally greater than those introduced from other sources."

Jan 1, 2017

By K. Miao, W. Mu, M. Sharma, A. Haas, N. Dogan

"The ever increasing demand for cleaner steels with low inclusion content has highlighted the limits of our current knowledge for controlling and predicting inclusion agglomeration and removal during liquid steel processing. Key knowledge gaps in this area result from the complex nature of the problems associated with measuring and visualizing the phenomena studied. Confocal scanning laser microscope (CSLM) allows for continuous in situ observation of micron-size samples in real time, at high resolution, under conditions relevant to the steelmaking process. This paper summarizes some of recent CSLM applications in our laboratory to illustrate the methods of analyzing transient behavior. The reaction between inclusions and slag is given as an example. The dissolution rate of calcium aluminate inclusions in CaO-SiO2-Al2O3 slags has been studied at elevated temperatures: 1500, 1550 and 1600°C as well as thermodynamic/kinetic analysis. It is found that total dissolution time decreased with increasing temperature. The rate limiting steps are discussed. It is shown that the diffusion through a product layer is responsible for dissolution at 1500°C. At higher temperature, dissolution is most likely controlled by both boundary layer diffusion and chemical reaction at the slag-inclusion interface. In this paper, the evidence for and against the theory will be critically examined and repercussions of the theory to steel refining processes will be discussed.INTRODUCTION Inclusion formation during liquid steel refining is an unavoidable consequence of current ladle steelmaking processes. The nature and quantity of the inclusions formed in steel is critical in steelmaking, as it affects both productivity through clogging, and downstream physical properties of the steel. It is therefore crucial to better understand and control the formation, agglomeration and dissolution behaviour of inclusions in a slag in order to improve the removability of inclusions from liquid steel. Most research (Sandhage & Yurek, 1988; Sandhage & Yurek, 1990a; Sandhuge & Yurek, 1990b; Sandhuge, 1991) relevant to the kinetics of inclusion removal has been obtained by using a technique where simulated inclusion material (ceramic rods) is dipped in slag and the dissolution rate is measured. While much has been learned using this approach, the difference in scale from bulk materials to inclusions is likely to have a significant bearing on the dissolution kinetics of inclusions in a slag and will certainly result in a very different influence of capillary effects. Further, the data obtained using an indirect (dip test) procedure relies on a comparison of the initial and final conditions of a sample rather than in-situ observation which can be achieved in a confocal microscope in real time."

Jan 1, 2017

By Alan Diaz Butron, Eng. Thierry Bernard

"In tunnel blasting the most challenging objective is definitively obtaining the maximum advanceassociated to a minimum overbreak. Achieving 100% of advance with no overbreak is the targetchallenge by Chavimochic Consortium. Chavimochic Special Project is an irrigation system that extends throughout much of the coast of the La Libertad Region, on the north coast of Peru. In 2012, it began management for construction of the third and last stage of CHAVIMOCHIC to irrigate lands of Chicama Valley, North of Trujillo. This project of 13 Km (8 mi) of various tunnels, it's a combination of technology and daily optimization by experienced people, which allow to accomplish the objective. Achieving this advance with no overbreak provide a huge saving on time. This paper describes the method, technology used, and the results obtained on more than 600 blasts done with conventional initiation system on the first 3 km (1.86 mi)."

Jan 1, 2017

By Dario Libano, Franz-Werner Gerressen

"Diaphragm walls are known as underground structural elements commonly used for retention systems and permanent foundation walls or elements. Of course they can also be used as deep groundwater barriers. This paper will focus on the construction work in an urban area like Sao Paulo. The Line 5 of Metro Sao Paulo is one of four network expansion projects undertaken at the same time. The projects will cover various areas of the city. The Line 5 on São Paulo’s south-side will be extended 7.1mi (11.5km) to serve 770,000 riders per day, stretching a total of 12.4mi (19.9km) along 17 stations. The extension line will facilitate access to the city’s central section and the commercial and hospital districts located along the line. The Brooklin Station, subject of this paper, had to be carried out in a special five shaft shape design, shaft diameter 131ft (40m) each, without using ground anchors. A focus will be taken on the special requirements of the installation of the arrows as well as on the specialties of installation for the shaft shaped layout. Therefore, it was required to install a 3.3ft (1,000mm) diaphragm wall using a specific layout especially in the connecting sections of the shafts, the so called arrows, to provide a bearing area for the struts. Maximum wall depth was about 121ft (37m); the total volume was about 20,060 cubic yard (15,337m³). The paper will describe the construction method and the sequence of activities required for the construction of this diaphragm wall using a combination of hydraulic grab and trench cutter system.INTRODUCTIONThe Line 5 Extension, in the city of Sao Paulo/Brazil, is currently the most important investment in public transport by Sao Paulo state’s government. It will connect the south part of the city to the city center, crossing through four other major METRO lines and stations, all currently in operation. The extension includes a new parking yard for the trains and 11 new stations. The Brooklin Station is one of the new stations and has a unique geometry of five secant shafts. The station should open and operate in 2016.The original design included constructing five secant shafts stabilized by two plastic slurry walls using conventional grab technology. One of them was to contain the contamination plumes in the neighborhood and the other for temporary support to enable the excavation of the shafts. The final retaining wall design was reviewed and changed to a concrete structural diaphragm wall. The reason of design change was as well the reduction of construction time of the shafts by half to meet the schedule as to avoid dewatering effects in a geological region characterized by Quaternary sediments and environmental contamination plumes. It was the first time that a trench cutter (hydromill) was used in such a situation in Brazil. The cutter increased the quality of the joints by overcutting, and decreased the probability of having seepage into the shafts. The cutter created a seepage barrier and avoided movement of contamination."

Jan 1, 2017

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"This document investigates a newly developed technique with the objective of improving terrain triangulation models (horizontal/sub-horizontal and vertical/sub-vertical terrains), mainly blast free faces. The algorithm uses multi-linear regressions to generate the best point cloud projection plane by applying the residues modulus minimization so as to create the finest 3D triangulation model. A change of base is required to create a new set of coordinate axis and generate completely new projection planes. The projection plane residue analysis is inferred in order to avoid or reduce the outlier points. The dataset is composed of 12 terrain models obtained from photogrammetry and a 3D Laser equipment thatgenerates georeferenced cloud points. This new technique is validated by the analysis of the obtainedcritical burden by the improvement of the general aspect view of the terrains and the capacity of outlier’s detection. The result and the quality of the algorithm demonstrates the improvement in the triangulation mesh, reducing errors in the calculation of over/under burden, free face volumes, cavities and, therefore, in the estimations of clearance/safety distances."

Jan 1, 2017

By Jim Bruce, Peggy Hagerty Duffy, Mary Ellen Large, Allen Cadden

"Over the past 40 years, Deep Foundations Institute (DFI) has executed its mission “to bring together multi-disciplined individuals and organizations to find common ground and create a shared vision and consensus voice for continual advancement in the deep foundations industry”. Like DFI, micropile technology began a significant growth path in the mid-1980s. This paper highlights how DFI’s mission was executed in the deployment and expansion of micropile technology.INTRODUCTIONMicropiles are small diameter foundation elements constructed using specialty drilling and grouting methods. Micropiles have evolved since their introduction into the North American market in the 1970s from being lightly loaded (less than 30 kips) elements used primarily for remedial applications, to today’s high-capacity, often hybridized foundation systems, for both remedial and new-build projects. Micropiles now occupy a substantial market segment in North America.For 40 years, DFI has aimed to be the forum for discussion of all issues related to deep foundations design and construction. DFI now supports 21 technical committees and working groups on all deep foundations technologies and has expanded to include regional chapters in Europe, India and the Middle East.Several key steps are required for the successful execution of DFI’s mission, including identifying a need, engaging dedicated and knowledgeable people, developing effective vehicles and resources for information sharing, cultivating stakeholder contributions and advancements, stimulating influence/impact on deep foundations market, and expanding approaches to continue progress. Pile drivers in New York City (the original organizers of DFI) positively affected their market using these same steps: they recognized a specific need, gathered the people who could affect change, convened a discussion forum (which is common today, but was innovative at the time), defined tasks to address the issues, and influenced their market by improving means, methods and owner perception of their services. These forward thinking, proactive members created a mechanism for communication among all related parties that would advance the profession by improving safety, quality and value of pile driving construction.Micropile technology has evolved in the United States and around the world for the past four decades. The accumulated efforts of DFI and other, similar organizations such as The International Association of Foundation Drilling (ADSC) have contributed to this evolution. The advancement of the micropile industry – and consequently the micropile market – has been intimately tied to the execution of the mission of DFI."

Jan 1, 2017

By Dale S. Preece, Ruilin Yang

"Air-decks are often employed for presplitting along the final highwall of a blast and are sometimes also included at the bottom or in the middle of explosive columns in the production portion of a blast. Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidlyattenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that theresulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of theexplosive."

Jan 1, 2017

By L. Lorio, B. Hilscher, P. Nayak, N. Yoon

"Mining has been a staple to technological advancement ever since the dawn of time. By harnessing the different physical and chemical properties that each mining commodity brings to the table, more and more innovation is developed and manufactured. As these non-renewable resources continue to be extracted, the industry as a whole faces a challenge in finding the next economical deposit as well as declining grade at the current operations. By means of pre-concentration, ore sorting aims to separate the barren material from the valuable ore to reduce energy consumption and tailings generation, while increasing the feed grade, concentrate grade, mill recovery, and revenue. In addition, ore sorting allows the modification of deposit geometallurgy in order to allow the creation of an optimal mill feed. This paper evaluates the applicability and challenges of ore sorting by utilizing the results from four different mines, and reviews them in detail. The mines include one underground and three open pit mines that are precious metal operations. In order to understand the applicability of ore sorting in these operations, initial rock-by-rock test results and different types of assays (atomic adsorption [AA], inductively coupled plasma [ICP], and fire assay) are utilized. Using the assay results, the grade recovery curves for ore sorting are generated and they are further improved by using and developing an ore sorting algorithm, which is discussed in this paper. The application and evaluation of ore sorting in greenfield and brownfield properties will also be discussed. The state of the art ore sorting technologies for both rock-by-rock and bulk sorting are also reviewed in this paper. The future technologies on the horizon, including different combinations of sensors, are explained. The sorting technologies include X-ray transmission (XRT), X-ray fluorescence (XRF), colour, infrared, electromagnetic, and laser induced breakdown spectroscopy (LIBS)."

Jan 1, 2017

By Brian Wilson, Megan Atkinson, Richard Diggle, Nathan Sweeney

"Ruskin Dam, located near Mission, British Columbia, was constructed in 1929 and 1930 and comprises of a concrete gravity dam structure founded on bedrock. At the right abutment, which consists mostly of dense to very dense sands and silt, the dam abuts against overburden soils, and connects to a cutoff wall system consisting of sloping concrete slabs. Significant seepage and piping issues were encountered during first filling of the reservoir in 1930. In 2012, BC Hydro, the owner of the dam, awarded a contract for the construction of seepage control measures at the right abutment, including construction of a plastic concrete cut-off wall extending upstream of the dam, a plastic concrete seepage training wall extending downstream of the dam, tie-in of the new cutoff wall to the dam, consisting of jet grouting of the soils adjacent to the dam to allow for the construction of the special cutoff connecting the cutoff wall to the dam, and construction of additional jet-grouting ground improvement downstream of the dam.Integral to the upgrade was the requirement for the special tie-in cutoff wall, consisting of a highly flexible, impermeable membrane to connect the concrete dam to the new, 1 m thick plastic concrete cutoff wall. The tie-in extends vertically into bedrock through the dam and jet grout columns constructed adjacent and beneath the overhanging portion of the dam at the right abutment. The membrane is required to survive the anticipated earthquake induced deformation between the dam and the abutment soils.This paper describes the processes used to develop a material suitable to meet the specified flexibility and permeability criteria, as well as the innovative construction techniques utilized to construct the slot and place the bituminous material within it. The final dimensions of the slot were in the order of 7 m long by 25 m deep by 0.17 m wide. The bituminous material was placed under a head of water which was required to maintain stability of the slot, and was placed at temperatures in excess of 120 degrees Celsius."

Jan 1, 2017

By Michael G. Nelson, Amy Richins, Ashley Hodgson, W. Pratt Rogers

"Sociotechnical systems are everywhere in the modern industrial world. Sociotechnical systems describe how humans interact with technology throughout a variety of processes. These systems are prevalent in modern industrial settings, such as operating mines. Safety and health management systems (SHMSs) are complex sociotechnical structures designed with the aim of managing and reducing occupational risk. U.S. mining companies are voluntarily adopting SHMSs to supplement regulatory safety compliance efforts. Like all complex sociotechnical systems there are a wide variety of approaches and adoption philosophies around a SHMS. Many SHMSs suffer from high levels of redundancies, which manifest themselves in diverse ways: duplicate processes, forms, permits, and tracking mechanisms. These redundancies have severe impacts on the overall system and absorb critical culture and leadership “energy”. A recent study initiated by the University of Utah and sponsored by the Alpha Foundation is investigating the effectiveness of SHMSs across 15 different U.S. mining sites. A large amount of data has been captured to help characterize elements of SHMSs and correlate their impacts on safety outcomes. Many variables were assessed in the study. Those of importance to this paper are the variables describing the robustness of the sociotechnical aspects of the SHMS. Two such variables are the overall integration of the SHMS within the whole system and how data is managed. Data management in this context deals with the approach to capturing, analyzing, and acting on data within the system. As well, systems are integrated around controlled, data-sharing mechanisms. It has been found that wide variety of approaches has been taken to integrate the SHMS within the governing management philosophy at a given site. A series of case studies is presented that develop some specific best practices for proper data management and integration of SHMSs.Introduction and Project Background Managing occupational health and safety can be done in many different ways, and with many different approaches, but is often based on the host country’s regulatory and industrial culture. However, many companies have extended their effort beyond the regulatory requirements of their host nation and have implemented Safety and Health Management Systems. The goal of these efforts is to reduce and eliminate occupational risk. Many health and safety practitioners have a hard time justifying various elements of health and safety management. There is a lack of institutional knowledge that measures and assesses the effectiveness of these Safety and Health Management System (SHMS) elements. To better understand the effectiveness of SHMSs the Alpha Foundation has funded a research project with the University of Utah. The title of the project is “Characterization and Effectiveness of Safety and Health Management Systems in the U.S. Mining Industry.” The research team will assess the SHMSs of 15 United States mine sites. The outcome of the project will be a method to characterize the strength of the SHMS elements, assess a culture and leadership index, and finally establish correlations between elemental risk and safety outcomes. The study is currently in progress. However, many important outcomes have already been observed, particularly on the data management practices within an SHMS."

Jan 1, 2017

By Qing Wang, Xiaochuan Xu, Jianping Liu, Xiaowei Gu, Qingyu Zhu

"The ecological costs related to the various optimized production schemes were calculated based on the designed ultimate pit. Moreover, the influence of the ecological costs on the selection of production schemes was discussed. In one designed pit, a series of geologically optimum pushbacks with sufficiently small increment were produced using the floating cone method founded on the principle of the highest metal content. Then all the pushbacks were reordered by the dynamic network diagram. The production scheme with the maximum NPV route was considered as the optimum one. The ecological impacts produced by mining were quantified and the ecological cost calculation models, which contain the direct eco-value loss, the indirect eco-value loss, the eco-restoration cost and the carbon emission cost were proposed. In one big open pit mine case, various production schemes were optimized and the one with maximum NPV was selected without taking into account the eco-costs. The scheme with the maximum comprehensive profit was obtained by calculating the eco-cost of each scheme. The results showed that the best scheme considered with the eco-cost was not the scheme with the maximum NPV. Therefore, the eco-cost presents the effect on the selection of the best production scheme.Introduction Optimizing production scheme is to determine the mining quantities of ore and rock, the pushing position of stope each year, and maximize the NPV of mine. In the theory, production scheming optimization has gone through trial and error (Pana and Carlson 1966), linear programming method (Johnson 1968), mixed integer programming (Gershon 1983), integer mapping (Kim and Cai 1990), dynamic programming et al (Gu et al 2014). In recent years, the study on production scheduling optimization has been focused on two aspects. On the one hand, the study is to solve the investment risk caused by the uncertainties of economic and geological environment (Ramazan and Dimitrakopoulos 2013, Marcotte and Caron 2010, Lamghari and Dimitrakopoulos 2012, Godoy and Dimitrakopoulos 2004, Benndorf and Shishvan 2014). On the other hand, the emphasis of the study was on reducing the problems for the optimization algorithm, to make it more efficient and practical (Cullenbine et al 2011, Shishvan and Sattarvand 2015, Askari-Nasab et al 2011, Nasab et al 2010). However, different production schemes cause different damage of mine land and pollutant emission, thus triggering environment problem. With the improvement of people’s consciousness of environment protection, the environmental issue of mining has been attracting more and more attention."

Jan 1, 2017

By Sedat Esen

"This paper presents a critical review of the fragmentation data obtained from some large open pit copper and gold mines. Database ncludes 35 mines with Uniaxial Compressive Strength values ranging from 19 MPa to 227 MPa (2756 psi to 32923 psi). Variation in the fragmentation data and the causes are discussed in detail. Quality assurance/quality control (QA/QC) in drilling and blasting was shown to have significant impact on fragmentation. In addition, controllable blast design parameters including drill pattern, powder factor, blast timing, stemming length, etc as well as the large blast sizes havesignificant potential to improve fragmentation. Feed size requirements of crushing and grinding circuits were discussed in detail. The paper discusses the effects of different size fractions (top size, 80 %passing size and % passing 10 mm (0.5 in)) on the downstream processes and the role of the fragmentation model in the mine to mill process. Blast domains based on rock strength and structure canbe established by using a fragmentation model which is calibrated using measured fragmentation data. This allows the blast engineer to compensate for changing rock characteristics and stabilize the ROMfragmentation size and result in increased crusher and mill throughput. Two case studies were presented to demonstrate the benefits achieved in downstream processes. Main benefits were reduced downtime at crusher circuits, improved mill throughput as well as reduced total operating cost. A simple relationbetween uniaxial compressive strength and powder factor was proposed using the database for the optimized mines as a guideline to allow site engineers to compare their sites against the other sites."

Jan 1, 2017

By Fernando J. A. S. Barriga

"Recent concerns over the availability of many mineral raw materials, and newly available technological developments, produced renewed interest in deep-sea mining. However, environmental concerns, with variable degrees of justification, are raising opposition to the concept. The forecast for the behavior of consumption versus availability of many raw materials, nearly all critical metals, arguably show that consumption will grow much faster than resource discovery onshore. Finding new sources of raw materials seems inescapable. The deep seafloor stands out as the only likely candidate.Sea Floor Mining and the EcosystemMarine mining has already started, decades ago, for diamonds, currently up to depths near 400m. Although the industry recognizes there is a footprint, it considers the footprint quite minor, because the area mined is small: in Namibia, where offshore diamond mining is now 70% of the country’s total, only 3% of the concession of 3,700 sq miles (9600km2) have been mined. As plans to mine deep-sea massive sulphide deposits and polymetallic nodules progress, the environmental concerns grow. Some of these concerns are as follows:?The deep-sea ecosystems are composed of long-lived species, with low rates of reproduction. The environment may not recover from mining on a human time scale;"

Jan 1, 2017

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Attasit Korchaiyapruk, Edward C. Clukey

"A deep mixing method (DMM) foundation was selected by the Project Team for a very large LNG facility in West Africa. As described in a companion paper, this foundation consists of a large number of columns installed by mixing cement with in-situ soils. The foundations are arrayed as a variety of honeycombed type configurations which, if installed to desired specifications, can provide a robust foundation alternative. The foundation is capable of distributing loads and limiting settlements even if some of the soil in the columns is not fully mixed during installation. An important part of the overall quality assessment program, therefore, involved developing a testing program to verify the methodology. In addition the impact of potential defects in columns on the overall foundation integrity had to be assessed. This paper describes some of the preliminary work done to establish the requirements for the quality assurance program. A key component of this program involved the sampling frequency used to assess potential defects in the columns. To verify the column integrity 104- mm samples were taken continuously at a selected frequency through the 23 m long columns. The preliminary work described in this paper demonstrated that the appropriate sampling frequency depends on both the desired reliability level as well as the number of defective columns encountered during testing.Initial finite element analyses were performed to assess the extent that defects could occur in columns within the honeycombed structure without adversely affecting the overall foundation integrity. The results from this work demonstrated that the spatial location of the defects was critical to properly assessing the foundation integrity.In addition to column sampling a load test was performed as part of the foundation verification process. The methods used to apply appropriate loads so that loads at the bottom of the columns approached design values are discussed in the paper.The results obtained from this preliminary study were then used to help develop a more comprehensive assessment program, described in a companion paper, to determine the robustness of the DMM foundations for both the LNG processing facilities and a condensate tank.IntroductionFoundations constructed with the Deep Mixing Method (DMM) can be an attractive and cost efficient alternate to other deep foundation options. This foundation is constructed by mixing soil and cement with an auger type drill. The foundation is usually constructed with a dual auger system that simultaneously creates two contiguous columns called foundation elements. Many elements are then arranged in a honeycombed configuration to create the overall foundation (Figure 1). A desired column strength can be obtained by varying the volume of cement added to the columns, the mixing rate of the soil and stroking sequence."

Jan 1, 2017

By A. Mazhary

"Although sensor-based ore sorting has gained significant attention recently, sorting gold deposits still face a high level of skepticism by gold mining companies. In order to shed some light on the matter, this article looks at two different gold deposits that were examined using X-ray Fluorescence, Electromagnetic and X-ray Transmission sensors. The heterogeneity of each sample is measured based on the assay results of each particle and is related to its sortability. Multivariate linear regression analysis was also performed on the XRF results to find potential proxy elements for detecting gold. The results from these deposits were varied and each sample showed different levels of sortability. While both X-ray sensors proved efficient for different deposits, the electromagnetic sensor failed to produce any promising results. Despite unsatisfactory result for one sample, this technology can have significant advantages in terms of lowering the operational costs and improving head grades and recoveries providing that the deposit is amenable to such separation methods. Therefore, it is important to mention that sensor-based ore sorting is ore and sensor dependent, and as a result, it cannot be applied and be beneficial to all deposits. Therefore, amenability tests are required in order to examine the potential for sensor-based ore sorting before one can reject the idea.INTRODUCTION Although sensor-based ore sorting has gained significant attention recently, sorting gold deposits still face a high level of skepticism by gold mining companies. Except for a few cases presented previously, no new case studies have been published. Previously, mines such as Kloof Gold Mine in South Africa used an optical sorter to sort their waste stockpile in 2003–2004 (Von Ketelhodt, 2009) and then again in 2009 (Von Ketelhodt, Falcon, & Falcon, 2011). More recently, Coeur Operations utilized an XRT sorter for their Kensington Mine in Alaska (Lasley, 2014) and also Anglo-American Platinum used an XRF sorter to pre-concentrate Platinum Group Metals through an algorithm that used chrome, copper and nickel as proxies (Rule, Fouchee, & Swart, 2015)."

Jan 1, 2017

By M. B. Kime

"A set of experimental batch leaching tests studied the effect of pH, time, temperature, and stirring speed on the relative Cu, Co, Ni, and Fe leaching yields of an oxidized copper-cobalt ore sample in an aqueous hydrochloric acid solution. The results were statistically analyzed and modelled using the structural equation modelling method. Models showed that Cu, Co, and Ni leaching yields were strong functions of the leaching time and leaching temperature, whereas the Fe leaching yield depended on the leaching temperature, stirring speed, and pH. Under optimum leaching conditions yields were 99.8% Cu, 82.4% Co, 91.3% Ni, and 30.6% Fe.RÉSUMÉ Une série d’essais expérimentaux de lixiviation en bâchée ont été menés pour étudier l’effet du pH, de la durée d’attaque, de la température et de la vitesse de brassage sur les rendements relatifs de lixiviation du cuivre (Cu), du cobalt (Co), du nickel (Ni) et du fer (Fe) d’un échantillon de minerai de cuivre-cobalt oxydé dans une solution aqueuse d’acide chlorhydrique. Les résultats ont été analysés et modélisés statistiquement à l’aide de la méthode de modélisation par équation structurelle (SEM, de l’anglais structural equation modelling). Les modèles ont montré que les rendements de lixiviation du Cu, du Co et du Ni dépendaient énormément de la durée d’attaque et de la température de la lixiviation ; le rendement de lixiviation du Fe, quant à lui, dépendait de la température de la lixiviation, de la vitesse de brassage et du pH. Dans des conditions optimales de lixiviation, les rendements étaient de 99,8 % pour le Cu, de 82,4 % pour le Co, de 91,3 % pour le Ni et de 30,6 % pour le Fe. INTRODUCTIONThe Katanga province in the Democratic Republic of Congo hosts the northwestern part of the Central African Copperbelt. This region abounds with large, rich deposits of sulfide and oxidized copper-cobalt ores. In general, the main valuable minerals present are malachite (CuCO3Cu(OH)2) and heterogenite (CoO(OH)). Common impurities found in heterogenite are Cu, Ni, Si, Al, Mn, and Fe. The substitution of Co by other cations (e.g., Cu, Ni, and Fe) has an influence on the crystallinity of heterogenite (Deliens, 1974). In general, well-crystallized varieties of heterogenite have lower impurity contents, whereas amorphous heterogenite types usually contain more impurities (Thys et al., 2009). Further, in heterogenite, Co can occur in the 2+ and 3+ oxidation states. The gangue generally consists of quartz (SiO2), talc (Mg3Si4O10(OH)2), kaolinite (SiO2·Al2O3·2H2O), limonite (Fe2O3·3H2O), and goethite (FeO(OH)). Oxidized copper-cobalt ores are often treated by hydrometallurgical methods, whereas sulfide ores are often treated by flotation or pyrometallurgy, depending on their grades. Hydrometallurgical methods typically entail selectively dissolving the metals of interest (Cu, Co, and Ni) in aqueous solutions (leaching), transferring the dissolved metals to an organic solution, and retransferring these to a second aqueous solution (solvent extraction). Copper and nickel are readily dissolved in an acidic aqueous media. In contrast, cobalt is difficult to dissolve, especially if it is present in the third oxidation state; however, this species becomes soluble after it is reduced to Co2+ (Mwema, Mpoyo, & Kafumbila, 2002; Kime & Makgoale, 2016)."

Jan 1, 2017