Search Documents

This paper quotes the results of many years of experiments and observations concerning ore drawing from mining blocks in major ore deposits mined by bulk induced caving of ore and country rock. Numerous laboratory and commercial test results of Russian, Ukrainian and Kazakh mines have been used and processed. Over 35 per cent of all ferrous, non-ferrous and other ore mined in the Russian Federation by the underground method is drawn underneath overlying caved rock (including ore drawing after bulk caving of pillars). The complexity of the process denies a logical or engineering calculation answer to many commercial production questions. Hence the massive research of ore drawing issues targeted at ore recovery forecasts in specific instances in order to assess an engineering solution or to define the design or planned ore draw performance. At first, the conditions were pictured as ideal. Subsequently, it was attempted to take into account the side contacts of ore with the country rock and the caved barren rock, the small size stuff in the caved rock, the unevenly loosening ore, end draw, and so on. The ore draw information available provides ample qualitative characteristics of the phenomena and only approximated and partially quantitative characteristics for individual cases. Many specific situations require individual studies of subject specific models.

Jan 1, 2000

By J. Paraszczak

High productivity of the equipment employed is one of the key factors in reducing production cost in mining. One of the best ways to achieve it is an increase in availability. In order to identify the most adverse factors affecting it, reliability and maintainability analysis ought to be done. If its results are to be conclusive, a sufficient amount of credible and consistent data is indispensable. Following the experience from field studies done in underground mines, this paper discusses the current status of failure and maintenance reporting, as well as problems encountered. It exposes the importance of adequate data collection on failures and downtime as well as it reviews the benefits of analysis based on such material. The question of benchmarking with regards to mining equipment performance is also addressed. The paper concludes with some recommendations on data collection and processing, as well as stresses the need to standardize the most important reliability/ maintenance notions throughout the mining industry and to conceive appropriate performance measures.

Jan 1, 2000

By R Lewis

Drill hole magnetometric resistivity (DHMMR) is a relatively recent addition to the explorationistsÆ suite of techniques for finding further resources in the vicinity of a drill hole. The method relies on gathering of an applied current into zones which are less resistive than the country rocks and it was first applied to exploration programs looking for weakly conductive sulphides, such as, for example, carbonate-hosted zinc deposits. More recently, it has been applied to a wider range of deposit styles, including highly conductive nickel sulphides. It has been found that the technique is capable of not only detecting mineralisation not seen by conventional electromagnetic (EM) techniques, but it can detect at a greater distance. Also, whilst EM is superior at defining tabular-shaped conductors, DHMMR may be more effective at finding cigar shaped sulphides. This paper presents a number of examples illustrating these findings.

Jan 1, 2000

By T. Asahina, M. Nakamura, M. Mabuchi, I. Shigematsu, M. Nakanishi, G. Yamauchi

"Commercial stainless steels (SUS304L and SUS430) were subjected to equal channel angular extrusion (ECAE) at room temperature to a total strain of 2.3 to 9.2. For each type of stainless steel, it was shown that the sample processed by ECAE showed higher room temperature strength than the as-quenched sample. This is probably due to the heavily worked structure. On the other hand, both strength and elongation of the ECAE processed SUS430 were increased by annealing at 773K. It is likely that higher strength is attributed to both the heavily worked structure and fine substructures. It is also likely that higher elongation is attributed to the fine substructures. It is concluded that ECAE is available for improving the room temperature strength of commercial stainless steels.INTRODUCTIONEqual channel angular extrusion ( ECAE ) is a technique that provides the repetitive deformation and allows to high intensity of deformation. With this procedure, a sample is pressed through a channel that has an equal cross section but bent at an angle of ?> [1-2]. Shear strain is introduced when a sample passes through the bending point of the channel. Repetitive processing is feasible because the cross-sectional dimension of a sample has no change during processing. To date, many reports have described that ECAE is available for the fabrication of fine-grained materials [3-14]. On the other hand, an ECAE processed sample can achieve high intensity of deformation through repetitive deformation. According to the equation given by Segal [ 2 ], a strain of about 1 is introduced in each pass through die if the angle ? is 90 deg.It is well known that high tensile strength can be achieved in metallic materials through work hardening [15]. It is also known that metallic materials with fine grain size show high strength [16]. Hence, it is expected that ECAE is available for strengthening method in metallic materials. In the present paper, we will report the mechanical properties of stainless steels processed by ECAE. As samples, SUS304L austenite stainless steel and SUS430 ferritic stainless steel were chosen. Each alloy has a single-phase structure (fee or bee) and shows no phase transformation, so that transformation strengthening cannot be applied. Hence, a heavy cold work such as ECAE may be effective for strengthening of this stainless steel. Annealing was conducted for the ECAE processed SUS430 to vary its microstructure. Then, the effect of annealing on the strength of the ECAE processed SUS430 was also investigated."

Jan 1, 2000

By Yoshifumi Abe, Akinori Toraiwa

"Nippon Mining & Metals started a new copper anode slime treatment plant that processes slimes in a chloride media. The basic plan of the process was proposed by Mr. James E. Hoffmann and Nippon Mining & Metals modified and advanced to produce precious metals in acceptable qualities for the company. The process has a wet chlorination stage of decopperized slimes, a solvent extraction and a reduction stages of gold, a silver chloride reduction stage and separative reduction stage of its gold extraction raffinate. The new plant of this process started in 1997 and has been operated in good condition.IntroductionThe old anode slime treatment plant of Nippon Mining & Metals, located in it's Hitachi Refinery, processed anode slimes through a combination of pyrometarllurgical processing and electrorefining. There was a need to plan a future of the plant because the maintenance cost increased year by year and a new selenium registration was going to be applied to the plant. Some plans were discussed and the result was that the process proposed by Mr. Hoffmann was superior among them.Nippon Mining & Metals started 'to examine the process and the experimental result showed that the process had an ability to be its new process but further research should be necessary to produce precious metals in acceptable qualities. The final process flow has some modified and additional stages to be suitable for its requirement. Silver processing stage is quite changed. Gold extraction stage has a new step to polish gold loading DBC. Gold extraction raffinate treatment stage is advanced to be able to recover precious metals, selenium and tellurium, separately. Aeration under atmospheric pressure is employed in decopperizing stage.The basic design of the new plant started in 1995 and finished in 1997. The construction of the new plant began in April 1997 and finished in October. The plant has been operating well after the four months test operation."

Jan 1, 2000

By Paul Worsey, Attila Szucs, Mark F. C. Schmidt

The use of water stemming with small explosive charges has been successfully developed at the University of Missouri-Rolla. Further study has been started to explore additional applications and uses for water stemming. Work has been focused in the areas of rock excavation and perimeter blasting techniques. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique for use with boulder fragmentation was published in last year’s proceedings. The excavation work took place in the form of both small bench and trench shots while pre-split and trim shots comprised the perimeter-blasting portion. The excavation work was located in both the Roubidoux sandstone formation and the Jefferson City dolomite formation. Hole diameters ranged in size from 1.5” to 3” diameter and powder factors ranged from l/l 0 to l/3 of the conventional charge weight. The water was used to both couple the explosive charge with the surrounding borehole, as well as stemming. No other stemming material or products were used. The method of using water stemming in perimeter blasting was found to work well. However, when used for excavation purposes, adequate rock movement was not obtained. The rock was often split, but not fragmented. The airblast was surprisingly low, but the ground vibrations were excessive. This is not the case with trim shots, and therefore this method appears ideal for splitting purposes, especially in areas where people do not like to stem the tops of the holes, and where airblast and vibrations are of concern. Water coupling dramatically increases splitting and fracturing. However, fragmentation is not only fracturing but also the movement and swelling of the material. As the charge weights are reduced with this method, sufficient gas volume is not created to cause this necessary movement and swell, which is critical in rock excavation. This explains why its successful application was limited to perimeter blasting applications.

Jan 1, 2000

By Takamasa Ishigaki, Gervais Soucy, Mohamed Rahmane

"The induction plasma jets employed for the in-flight nitridation of molybdenum disilicide (MoSi2) powders were investigated in terms of their flow characteristics. The present study shows the effect of the operating parameters of the plasma torch, as used for this process, on the plasma jet properties. The enthalpy probe techniques, along with mass spectrometry, were employed for the measurement of the jet temperature, velocity and concentration fields. The measured values were compared to the results of a numerical simulation performed on the plasma flowing inside the torch-reactor system. The process operating conditions studied were the plasma plate power, chamber pressure and sheath gas composition. The optimal conditions for effecting the nitridation process using thermal plasma are obtained at moderate plasma plate power, at around atmospheric pressure and by using a mixture of argon and nitrogen as the plasma torch sheath gas.IntroductionMolybdenum disilicide (MoSi2) based composites are considered to be one of the most promising candidates for high temperature structural material applications [!], especially because of their high melting points, good oxidation resistance and relatively low cost. However, the wide application of these composite materials is still limited by some factors such as their brittleness at room temperature and lower strength at high temperature (> 1500 K). To overcome such limitations, a number of researchers [2-4] have earlier studied various kinds of reinforcements for MoSi2, e.g. oxides, silicides and nitrides. More recently, Fan and coworkers [5-9] have demonstrated the possibility of in-flight nitridation and carburization of MoSi2, using a thermal plasma process. This work has confirmed the plasma synthesis route as one of the most promising methods for creating an in-situ second phase structure. Properties of the plasma flow, such as its temperature, flow velocity and composition, are of crucial importance for the nitridation of MoSi2 powders during their flight in the plasma. Therefore, the optimization of such a process involving plasma· generated reactive species necessitates a thorough understanding of the plasma flow characteristics."

Jan 1, 2000

By Anders Lagerkvist, Agne Rustan, Tommy Edeskar

Landfills containing house hold waste produces methane gas during its decomposition. This gas can be recovered and used for heating purposes or as fuel for vehicles. Gas drainage pipes are installed in the landfill and connected to a central suction point. Methane gas is produced over several years until the slots in the drainage pipes are clogged by black mud. And the bottom of the vertical drainage pipe are filled with mud and water. The hypothesis tested in this paper is if blasting in the drainage pipes could activate the production and flow of methane. In the first part of the paper we have studied what maximum linear charge concentration could be used in different size of PE-pipes place vertical on surface and surrounded by air. The results show that the maximum linear charge concentration for single blasts varied between 5-10 g/m, depending on the diameter of the pipe (90, 100 and 160 mm). Maximum charge concentration for the repeated blast varied between 2-5 g/m. In the second part of the paper we study what maximum linear charge concentration could be used in situ for full scale blasting tests in a special prepared test area which later on was dug out after the blastings. Up to 40 g/m could be used without damaging the top of the 160 mm diameter pipes. The increase in methane flow was so low so it could not be measured c4.5 m3/h. The conclusion therefore is that the stimulation of methane flow by explosives is not enough.

Jan 1, 2000

By Lewis Stansfield

A rotary displacement method was used to install permanent steel casings for bored piles through an asbestos tip. This method was chosen in preference to alternative driven systems because it was quieter and more versatile if obstructions were encountered. New equipment was designed and made specifically for the project, and stringent health and safety regulations had to be observed.

Jan 1, 2000

By S. S. Chabot, S. E. James

A recent survey of major steel companies worldwide revealed the importance of recycling zinc units from electric arc furnace (EAF) dust, mill scale, blast furnace dust and other zinc containing streams within the steel industry. Many processes have been developed and installed in response to this challenge. The most successful approach involves the production of a crude zinc oxide and its sale to primary zinc producers to recover the metal values. The problem with this process is the high concentration of halides in the crude oxide. This type of material cannot be processed directly in an electrolytic zinc plant because of the corrosion problems it will cause in electrolysis. In 1999, Big River Zinc installed a zinc oxide receiving and washing plant to minimize the impact of halides in its electrolysis circuit. A description of the washing plant and the initial operating results are presented in this paper.

Jan 1, 2000

By M. J. Collins

Pressure leaching of zinc sulphide concentrates has been practiced commercially for nearly two decades. The process, which includes direct leaching of concentrate with spent electrolyte in an autoclave, has been commercialized at four separate locations to date. In pilot studies carried out in the Dynatec lab in Fort Saskatchewan, dozens of additional zinc concentrates have been shown to be amenable to pressure leaching. This paper highlights recent improvements in zinc pressure leaching that have been identified through process development studies, and how the experience gained in these studies has been utilized in the development of a new copper pressure leach process.

Jan 1, 2000

By F. M. Doyle

Metal removal kinetics and metal ion selectivity in ion flotation were studied from a thermodynamic perspective. Surface tension data could be used with the Gibbs adsorption equation to quantitatively predict the metal ion removal kinetics in alkylsulfate-Cu systems. However, surface tensions predicted cation selectivity coefficients in the sodium dodecyl-sulfate (SDS)-Cu-Ca and SDS-Cu-Pb systems rather poorly, although the predicted order of the selectivity (Cu2+<Ca2+<Pb2+) was correct. Another thermodynamic selectivity model, which used the Grahame adsorption equation and a geometrical analysis, predicted cation selectivity coefficients that agreed very well with experimentally measured values.

Jan 1, 2000

By Peter Jackson

The dewatering of the large construction pits required for major infrastructure projects often has a significant impact on the environment. This is particularly so in urban areas and where groundwater resources are of interest. These environmental impacts are inter alia, groundwater lowering and the consequent effects such as settlement and deterioration of timber foundations, together with the impact of the dewatering on the groundwater quality. In order to minimise the environmental impact of the dewatering, the quantity of water to be abstracted and the amount of groundwater lowering in the surrounding area must be minimised. This paper describes the measures that have been taken on the Copenhagen metro project to achieve the objective of minimal environmental impact whilst still carrying out a major dewatering scheme.

Jan 1, 2000

The efficient and profit-maximising daily and long-term management of the Vera Nancy resource depends on decisions based upon assay data. This paper examines the range of sample sources, the methods of sample collection, assay techniques and Quality Assurance used by the mine. The orebody has a relatively low nugget effect for a gold mine (around 25 per cent) and this greatly assists in reducing sampling error and producing reliable assay data for production decision-making. Reconciliation between mine and back-calculated mill grades generally sees the mine under-calling mill grades by around four per cent.

Jan 1, 2000

Neither the copper orebodies nor the zinc-lead-silver orebodies at Mount Isa were formed syntectonically as has been claimed for the last 20 and 10 years respectively. Both orebody types were cogenetic, coeval, and formed early during the sedimentation and diagenesis of the host formation. The copper orebodies are interpreted as having formed diagenetically at hand specimen scale, syngenetically at formation scale. The zinc-lead-silver orebodies are interpreted as having formed primarily by sedimentary means at both hand specimen and formation scales.

Jan 1, 2000

The 103rd Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 16th August, 2000. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past Presidents, our Members and other guests, among them the following: Reinie Meyer, President, The Geological Society of South Africa Dr Nielen van der Merwe, Chairman, The South African Institute of Rock Engineering Chris Fourie, President, Institute of Mine Surveyors of South Africa

Jan 1, 2000

The importance of the minerals industry to any economy is clearly demonstrable. Its raw materials and products are the foundation of modem society and they have shaped the history of mankind from prehistoric times to the space age of today. However, those in the minerals industry have clearly failed to impress this fact on the consciousness of the public, bureaucrats and politicians. They have also failed to engage their dedicated opponents in a constructive debate. This is mainly because the minerals industry has been unwilling (until recently) to deal with the "soft" issues of civil society, nor understand and operate on a more emotional level. Technical professionals (as well as managers) in the future must be as comfortable in handling community concerns over social, environmental or landowner issues, as they are with logging complex drill core, designing blast patterns and separating one mineral from another. They must become caring, effective communicators and mediators. These are the new skills of a professional in the Third Millennium. These issues are outlined and discussed with some Australian data used to illustrate the point. If there is to be a future for all, then the policy makers within all levels of government (national, regional or local) must not drive essential mineral development offshore. They must address ways to support wealth creation mechanisms, particularly innovation. The minerals industry is a powerful wealth creator for ordinary citizens and an innovator. Politicians and their advisers must not .be allowed to forget this fact. If the ANZAC minerals industries do not win the emotional debate and successfully deal with the "soft" issues as well as they deal with the technical issues, there can be only a dim future ahead.

Jan 1, 2000

Bacterial leaching represents an unusual problem in biochemical engineering, because the substrate for bacterial growth is not supplied directly, but is a product of another reaction, the leaching of mineral particles. Leaching arises from the bacterial oxidation of ferrous ions to ferric ions, which in turn oxidize the mineral. For the bacterial dissolution of pyrite, these reactions are: [ ] (Y represents a stoichiometric yield factor, and N represents the amount of bacteria.) Equations [1] and [2] represent a cyclic auto-catalytic system since more ferric ions are added to the system with an increase in the extent of leaching.

Jan 1, 2000

By T Kang, V Sahajwalla, L Lu

During devolatilisation, physical behaviour of coals was investigated in horizontal electrically heated furnace with an inert gas atmosphere, and gasification rates of four coal chars and coke were measured thermogravimetrically in a carbon dioxide atmosphere at temperatures in the range 1100oC - 1500oC. The volume change of chars was also measured in horizontal electrically heated furnace at various temperatures. Both reactivity and the activation energy for the gasification of coal chars were found to be strongly influenced by pore structure and the carbonisation conditions employed during preparation. CO2 reactivity of chars increases with increasing reaction temperature, and particularly increases more rapidly over 1300¦C. CO2 reactivity of coke is lower than that of non-coking coal chars in the range of 1100¦C to 1500¦C. CO2 reactivity of chars with smaller pore area and bigger pore diameter is less than that of chars with bigger pore area and smaller pore diameter. During gasification, the volume of chars did not change significantly at the lower temperatures of 1100¦C and 1200¦C, but at the high temperatures, 1300¦C to 1500¦C, the volume of chars quickly decreased due to ash softening and melting. The CO2 reactivities of the chars are controlled by the mixed control of chemical reaction and pore diffusion in the temperature range 1100¦C to 1300¦C, and by bulk diffusion in the temperature range 1400¦C to 1500¦C.

Jan 1, 2000

By Y. P. Chugh, J. Ma

Higher production, better safety standard, and potential for automation are some of the benefits of longwall mining. Today, longwall face advances at a faster rate exposing many diversified rock layers in a short period of time. It is now a serious challenge to cope with ground control problems such as roof falls, face and floor failure, and excessive shield loading as fast as possible to minimize production and monetary losses. In Illinois coal mines, the existence of weak floor strata blow the coal seam may pose additional problems related to floor heaving, shield base punching, and associated roof and face falls. In this study, the effects of weak floor on longwall ground control are analyzed using two-dimensional finite element models. A two-leg 635.6-ton (700-short-ton) yielding capacity shield is included in the models to evaluate the effects of different thickness and material properties of the weak floor. The study indicates that the thickness and material properties of weak floor have significant effects on shield loading, the distribution and intensity of front abutment stress, failure zones in the surrounding strata, roof-to-floor convergence, and floor punching by the shield base.

Jan 1, 2000