Search Documents

By Paul D. Tavares, John Forbes, Eric R. Drooff

As the existing major U.S. - Canada rail tunnel was too small to accommodate double-stack container cars, Canadian National Railways is constructing a new parallel tunnel with a 50% greater diameter. Starting in Sarnia, Ontario, the new shallow-cover bored tunnel runs under a large research building and several other structures in an oil refinery before travelling under the St. Clair River. Maximum predicted settlements to be caused by the 9.2 meter diameter earth pressure balance TBM in the soft St. Clair till were in excess of 100 millimeters. As such, these settlements had the potential to cause severe damage and disruption to the existing refinery. In order to reinforce the soft clays below the refinery research building and other structures, and to compensate for settlement caused by the tunnelling, the ground improvement method of Soil Fracture grouting was successfully applied for the first time in North America. This paper will describe the details of both the soil fracture grouting application and the elaborate electrolevel remote monitoring system used.

Jan 1, 1995

By G. J. Desroches, E. Ozberk, M. J. Collins, B. D. Krysa, I. M. Masters

The zinc refinery of Hudson Bay Mining and Smelting Co., Ltd. went through a major modernization in 1993, when the roaster and the calcine and fume leach circuits were replaced by a new Sherritt zinc pressure leach plant. The HBMS plant, in Flin Ron, Manitoba, represents the first commercial application of the Sherritt two-stage zinc pressure leach process, with /00% of the zinc concentrate feed processed in autoclaves. The process design of the new plant required definition of the deportments of elements such as antimony, arsenic, chlorine, cobalt, fluorine, germanium, magnesium, manganese, selenium, tellurium and thallium. This paper describes the deportment of these elements in the commercial zinc plant during the first nine months of pressure leach operation, and compares these results with operations prior to the introduction of pressure leaching, and with the results of tests carried out in the She"itt laboratory during the process development phase.

Jan 1, 1995

By Ghassan Skybey

Australian coal mines uses state of the art technology in coal rib reinforcement. This paper highlights the development over the past 15 years in coal rib support technology, along with the advantages and disadvantages of each system. It also outlines the current trend in using coal rib reinforcement in speeding up the dowels installation to improve the current low drivage rate. An innovative cuttable dowel is discussed which improves the drivage rate. This new dowel is self anchoring it uses no resin anchor it has a 5 tonnes (5.51 tons) anchor capacity and can be fully installed in approximately 10 seconds.

Jan 1, 1995

By Grobler H. P, Chitombo G. R

Production blasting of Dc Beers Consolidated Mines Limited, Koffiefontein and Finsch Mines involves both uphole trough rings of 9 to I I holes and near vertical 360 degree compound rings of 42-54 holes. The rate of production from these stages is dependent upon being able to achieve a specified fragmentation size range and this has driven the derivation of blasting practices to consistently achieve this target fragmentation. At the Dutoitspan Mine, in Kimberley, where mining of the kimberlite pipe is by block caving, 100 per cent extraction of the undercut level by ring blasting is essential. If this is not achieved, pillars are formed which not only inhibit the efficient initiation of the caving process, but also concentrates load onto the extraction level, causing damage to draw points and pillars. These two case studies demonstrate the importance of achieving optimum blasting performance for downstream mining efficiency; ie fragmentation for increased productivity at Koffiefontein Mine and 100 per cent undercut extraction for efficient initiation of the caving process at the Dutoitspan Mine. The case studies also serve to highlight the long road towards blast optimisation taken by De Beers Consolidated Mines Ltd (Koffiefontein. Finsch, Premier and Kimberley Mines) since 1989.

Jan 1, 1995

By Christie A. B, Swain A, Brathwaite R. L

This study provides quantitative data on vein distributions within seven selected epithermal systems, four deposits hosted predominantly in rhyolitic rocks: Ohui, Wharekirauponga, Neavesville and Komata, and three major deposits mainly hosted in andesite: Martha Hill, Golden Cross and Karangahake. The technique of fractal analysis was used to help quantify vein distribution patterns. The fractal dimensions (D) obtained are related to the number of veins per metre, the degree of vein clustering, and vein thickness. An increase in any of these tends to increase the fractal dimension. It is the relative relationship of these parameters that is important for the characterisation of vein distributions, and the comparison of different deposits. Within the same systems, the rhyolites are characterised by lower vein thickness and vein density, but have a higher degree of vein clustering compared to the andesites. Sections that are deeper and more centrally located within the epithermal system and/or close to major structures, tend to have a greater degree of vein clustering, higher average vein thickness and density, and higher thickness to density ratios. This depth control is most pronounced in epithermal gold-silver systems because they have formed at shallow crustal levels where physico-chemical conditions change drastically both vertically and laterally. In addition to lithological and structural control at vein scale, deposit scale structure is of great importance in the deposition of economic mineralisation. Large open vein structures capable of sustaining high fluxes of hydrothermal fluid, favourable for the formation of large, high-grade gold deposits, are best developed in andesite sequences.

Jan 1, 1995

By Michael K. Rhodes

A 120 tonne per day BacTech bacterial oxidation plant treating refractory gold concentrates for Gold Mines of Australia's Youanmi project in Western Australia commenced operation September 1994. This was the first commercial application of the BacTech process. A pilot plant trial on concentrates produced from Youanmi ore was carried out at BacTech's laboratory in Perth. Results and measurements from this trial were used by Signet Engineering Pty Ltd to design the commercial plant. This paper cover the results obtained from the piloting, their implementation in the plant design and the initial commissioning of the full scale plant.

Jan 1, 1995

By G. M. Bernard

Cerro Colorado lies on the eastern edge of the Atacama Desert in the foothills of the Andean Cordillera of northern Chile. Compañía Minera Cerro Colorado SA (CMCC) operates Cerro Colorado. CMCC, headquartered in Santiago, Chile, is wholly owned by Rio Algom Ltd., of Toronto, Ontario. Cerro Colorado is located 120 km (75 miles)east of the port city of Iquique. Access is by 30 km (19 miles) of paved highway and 70 km (43 miles) of upgraded road. The mine site is located at an altitude of 2600 m (8531 ft) on a gentle west-sloping plateau adjacent to a deep canyon (Quebrada de Parca) to the north. Temperatures are moderate, ranging from 5° to 30° C (41° to 86° F) with an average annual rainfall of 20 mm (0.8 in.). The plateau is generally covered with 20 to 30 m (65 to 100 ft) of Quatemary sand and gravel overlaying bedrock. In the immediate vicinity of the Cerro Colorado deposit, a semicircular embayment has been eroded into a steep canyon wall that cuts through the surface gravels to expose a considerable section of the underlying bedrock.

Jan 1, 1995

This paper describes several sources of external dilution affecting the stope walls during underground sub-level and bench stoping. Factors which control ground behaviour such as the geometry of the openings, the influence of geological discontinuities, stress re-distribution and blasting practices are discussed. Crown stope instability due to stress concentrations induced by changes in the excavation geometry, is discussed and the most efficient ways to sequence blasting within a stope are analysed. Effects of undercutting by blasting, blast damage in the near field and cut-off slot blast designs are analysed. The influence of dynamic loading on the exposed walls as well as the practice of blasting fill passes within stope crowns are discussed.

Jan 1, 1995

By Golosinski T. S, Jorgenson J. D

Several methods are available for inspections of mine shafts. These involve use of inclinometers, moving beams, inertial platforms and decelerometers. Inspections which use decelerometers are of most interest since they allow assessment of conditions of shaft steelwork, conveyances and the shaft itself. This assessment is based on recording and analysing dynamic behaviour of shaft conveyances. Sample inspections of several WA shafts confirm feasibility of using this method for periodic shaft Inspections.

Jan 1, 1995

By N. V. Gorelikova

A new type of zirconium mineralization has been recognized in the Devonian volcanic rocks from an orogenic depression in the Central Kazakhstan. The most characteristic features of this deposit are the fine-grained nature of the zirconium mineralization, an unusual texture of the zirconium ores, and a close association of zirconium with phosphorus in the ores. Zircon grains form fine globular aggregates with the features of hexagonal crystal habit. In addition to crystalline zircon, the ores contain metacolloidal zircon, similar to hydrozircon. The morphological and textural features of the zirconium ores suggest that the deposition of ore deposits took place at a low temperature from colloidal solutions. It is believed that this deposit should be considered to be a new type of zirconium mineralization that is related to low-temperature hydrothermal processes.

Jan 1, 1995

By J. C. Stankus, S. S. Peng

Many coal seams are associated with soft floor strata. During mine development, if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One method for controlling floor heave is floor bolting. This paper describes the demonstration of flour bolting methods in a West Virginia, info coal mine. Three methods were used: vertical full resin bolting, floor truss bolting and floor truss bolting pins a floor slot at the center of the entry. The design of each method and the experimental results are discussed.

Jan 1, 1995

By A. K. Bakshi

Mineral suspensions show Newtonian flow properties at lower solid concentration, but change into non-Newtonian regime as the solids content is increased. For Newtonian fluids viscosity is independent of shear rate, but for non-Newtonian fluids it varies with rate of shear. Therefore, measurement of viscosity at a shear rate, different from the process will be futile unless the slurry is Newtonian. This is especially true for hydrocyclone operation, where the rate of shear is different at different points within the hydrocyclone. In this case, it is very important to determine the flow type of the suspension before attempting to establish any correlation between viscosity and process efficiency. A new technique to distinguish such changes in flow type has been developed. This involved a co-axial cylinder type viscometer which measured apparent viscosity at a low shear rate, and a vibrating sphere type viscometer which measured the apparent viscosity at a high shear rate. Special precautions were taken to allow measurements of viscosity of rapidly settling mineral suspensions. Because the vibrating sphere viscometer operated at a much higher shear rate than the rotating viscometer, the two instruments together could determine the shear-rate dependency of the viscosity. Ground silica of 80% passing 65~m size in water was used to prepare slurries at concentrations ranging from 1O-70wt% solids. Viscosity of each slurry sample was measured simultaneously by both the viscometers and the results were compared with each other. With this technique, it was found that all the silica slurry samples were in the Newtonian flow regime.

Jan 1, 1995

By Edita Vircikova

The best demonstrated available technology (BOAT) for the removal of dissolved arsenic and some heavy metals as reported by USEPA (Contaminants and Remedial Options at Metal Sites, Draft Report, August 1993) (1) is still the chemical precipitation. Coprecipitation with the excess of iron is usually practised because of the availability of iron at low/no cost and also in order to meet the stringent regulatory discharge limits. The arsenic is usually removed with iron because of its common occurence in the mined orebodies and the excellent adsorptive property of the precipitated hydrous ferric oxide compounds. There has been controversy, however, over the long-term stability of the arsenic-bearing ferrihydrite which is produced.

Jan 1, 1995

By Gleadow AJW, Foster DA, Kohn BP, Raza A

A large and increasing data base of apatite fission track results from sedimentary and granitic rocks exposed within the southeastern highlands and along the continental margin of Australia provides constraints for the tectonic development of the southeastern passive margin. The fission track results suggest that many regions of the southeastern margin of Australia experienced distinct episodes of relatively rapid cooling during the middle Cretaceous to early Tertiary that can be attributed to the effects of rifting. One cooling episode is middle Cretaceous in age and related to denudation of the southeastern highlands from Tasmania to northern New South Wales between -90-100 Ma. Rocks exposed along the present coast line record a later episode of rapid cooling, which is diachronous and decreases in age northward from -80 to 90 Ma in northern Tasmania to southern New South Wales, -60-80 Ma in central and northern New South Wales, and to -50-60 Ma in southern Queensland.

Jan 1, 1995

By M. C. Williams

The solution of the dynamic population balance model (PBM) of a closed grinding network consisting of a mill, sump, and cyclone is problematic. The fact that the dynamic PBM model equation solution to the Inverse Problem for grinding systems is degenerate or underspecified is demonstrated. Two numerical solution approaches to the Inverse Problem are used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data is used to demonstrate the non-unique functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. Different solutions to the same PBM transport equations are provided. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Two different solutions were obtained depending on the numerical solution approach. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995

Continuous improvement has become the watchword of the 1990s for most iron-ore-processing operations. In many instances, this improvement has been achieved through stepwise application of advanced control techniques to optimize operations. The benefits of this stepwise application have been great. However, they have fallen short of the full potential offered by the prospect of overall plant optimization. The successful integration of computers, instrumentation and control software throughout a plant promises to deliver an additional 3% to 5% of productivity in even the best-run plants (Herbst and Bascur, 1984). LKAB is Europe's largest iron-ore producer and a leading implementer of advanced control technology. In the late 1980s, LKAB introduced advanced control in its concentrator at Kiruna, Sweden to improve plant performance through higher productivity, greater efficiency and lower costs at each processing step.

Jan 1, 1995

By Mohsen Sanai, Paul Gefken

"SRI International has developed and patented* a castable dilute explosive tile @ET) that offersunique advantages over conventional high explosive. The primary advantages of DET are that itsdetonation pressure can be adjusted over a wick range and its impulse can be controlled independently by adjusting its thickness and configuration. Because DET has a much lower detonation velocity than conventional explosives, the pulse duration produced by DET is as much as 10 times longer than the pulse duration produced by conventional explosives for equal explosive weights. These features of DET present several advantages to the mining industry. For example, DET can be tailored so as to control fragment size and distribution to enhance extraction of desired elements from ore or breakup of specific regions."

Jan 1, 1995

By T. W. Camm

In this US Bureau of Mines report, mine and mill cost models are presented to make estimates of the cost to develop mineral deposits in the desert region of the southwest United States. Regression analysis was used to generate capital and operating cost equations for each model based on daily production capacity. These models are used for Potential Supply Analysis (PSA) studies by the Bureau, which analyzes the economic benefits of minerals in a region.

Jan 1, 1995

By Somerville M, Muray A, Bocking M

Australia has an extremely large total hot dry rock (HDR) resource above a depth of 5 km, equivalent to 7500 times its present annual energy consumption, of which 80 per cent underlies the Great Artesian Basin. The resources most likely to be exploited first are those residing in homogeneous granitic bodies beneath sedimentary basins containing insulating rocks such as shales and coal measures. In the Sydney Basin south of Muswellbrook, an area of high geothermal gradient corresponds to a gravity low thought to be a buried granite body at a temperature of possibly 250¦C. This locality is suspected to have the ideal geological characteristics for Australia's first hot rock test facility. Australia's high HDR potential is possibly unique in the world, in that the potential sites satisfy four independent, geological conditions, each considered as favourable for the creation of a resource, and for the ease of extracting that resource. They are: ò Higher crustal heat generating capacity than that of normal continental crust. ò Much of the Australian continent is covered by sedimentary basins which contain a high proportion of shales and coal measures that have low thermal conductivities, thus providing an insulating blanket for the heat being generated beneath. ò The sedimentary basins are in many places underlain by large untectonised granitic bodies that are not only a major contributor to heat generation, but also ideally suited to the establishment of HDR reservoirs. ò The crustal shortening stress field that is found in the majority of the Australian continental crust results in a vertical minimum principal stress orientation which should result in the development of favourably oriented horizontal stimulation cells necessary for maximising an HDR resource.

Jan 1, 1995

By Bearman R. A

The majority of published material regarding the operation of crushing machinery is concerned with simulation of performance rather than design of equipment. The reason underlying the bias in published material relates to why research is carried out and who undertakes the research. Two distinct types of research can be identified: 1. Internal research by crusher manufacturers - generally related to mechanical design, value engineering and to the commercial realities attached to sales demands. Any work on basic crusher geometry or rock/machine interaction is of a sensitive nature and rarely enters the public domain. 2. Academic research - mostly confined to modelling of crusher performance and simulation. This is not because of any bias, but crusher design requires access to manufacturers data or at least an in-depth understanding of crusher design, which is rarely available. The crushing of rock is a complicated problem. It involves three aspects; the machine geometry, the material composition (type of rock/feed size distribution) and the machine/rock interaction. The machine geometry is often ignored in empirical mineral processing simulations, while the response of different feed materials is only nominally addressed in machine specifications provided by manufacturers. The manner by which the machine produces a stress field and causes different types of breakage for different rocks (or the machine/rock interaction) is sadly neglected by both groups. All three aspects must be considered collectively to successfully understand and model the entire crushing process. 1. Centre for Mining Technology and Equipment, Julius Kruttschnitt Mineral Research Centre, University of Queensland, Isles Road, Indooroopilly 4068 Qld. The importance of crushing is often underestimated. In mining and mineral processing the invisibility of the crushing process is understandable as it merely provides a coarse reduction stage prior to the intricacies of mineral extraction. However in the quarrying industry crushing and screening basically provide the finished product. A brief overview of the quarrying industry shows the importance of crushing. Figure 1 gives production figures for most of the western European countries, Australia and the USA.

Jan 1, 1995