Search Documents

By S Cyphers, J Missen, B Jansen

The AGL Loy Yang Mine is one of the largest and most significant coalmines in Australia. Commencing in 1982, this mine produces 30–35 Mt/a to supply more than 50 per cent of Victoria’s electrical power requirements. At this mine there are unique geotechnical challenges to overcome to ensure its safe operation including: significant mine depth, low density of coal in the operating and permanent mine batters, the influence of groundwater and deep sediment aquifer pressures. One of the challenges is the behaviour of brown coal, which is neither a soil nor a rock and displays long-term creep stress relief. Other geotechnical challenges include ensuring stability in high unconsolidated dumps, potential large-scale block movement in mine batters driven by crack water pressure and heave from high-pressure aquifers.The paper will outline the geological and hydrogeological setting and potential failure mechanisms, and detail an integrated geographic information system and reporting regime that in part addresses ground control management at the mine. The paper will also outline the management processes for a dynamic geotechnical environment and the benefits of the alliance arrangements to meet the geotechnical requirements at the mine and the effective personnel integration in the mine technical services team.CITATION:Jansen, B, Missen, J and Cyphers, S, 2014. Geotechnical management at the AGL Loy Yang Mine, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 239–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By F T. Suorineni

Empirical methods are deeply rooted in geomechanics. This is a consequence of the recognised complexity of the nature of the rock mass. The usual assumptions of material continuity, homogeneity, isotropicity and linear elasticity often assumed for soil, concrete and steel are difficult to justify in a rock mass except for mathematical convenience. These assumptions form the bases for most mechanistic, analytical and numerical methods in geomechanics. Believers in empirical methods argue that the complexity of the rock mass and its interaction with structures developed in it is adequately accounted for in empirical methods, which compensate for our ignorance.Franklin (1993) defines empirical design as quantified judgement based on experience. He further states that empirical methods often prove ‘closer’ to the ‘truth’ than the apparently more precise predictions of theoretical analysis, adding that based on real data empirical methods provide a standard against which theoretical predictions are measured and can be judged. This paper takes a critical look at the common empirical methods in geomechanics – rock mass classification systems (Bieniawski, 1973; Barton, Lien and Lunde, 1974; Hoek, 1994a), Laubscher block caving design rules (Laubscher, 1994), the stability graph (Mathews et al, 1981), pillar design equations (Salamon and Munro, 1967; Hedley and Grant, 1972; and their derivatives), pillar design chart (Lunder and Pakalnis, 1997) and failure criteria (Hoek and Brown, 1980; and its derivatives). The common thread in the application of these methods is that in most cases they are often applied blindly without an understanding of the underlying assumptions and database limits. This paper emphasises that users of these methods need to know the underlying assumptions, database limits and inherent hidden risks that are often unmentionable for their satisfactory use. Finally, suggestions are provided for the efficient use of empirical methods and how they can be improved.CITATION:Suorineni, F T, 2014. Reflections on empirical methods in geomechanics – the unmentionables and hidden risks, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 143–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D Fukuda, K Kaneko, R Kudo, J Kodama, Y Fujii, T Sasaki

"Estimation of stress state as well as elastic modulus is important for the prediction of a rock slope deformation in an open pit mine since it can strongly influence the mining-induced deformation of the rock slope. This study applies a method to evaluate regional stress state and Young’s modulus by analysing the mining-induced deformation of ground. The effect of changes in regional strain state due to tectonic plate motion can be accounted for using the proposed method. Mining-induced deformation can manifest itself as changes in ground surface geometry resulting from mining activity. There are three underlying factors that can contribute to the deformation: displacement induced by the effect of gravity displacement induced by the effect of horizontal regional strain incremental change in the horizontal regional strain. The relative displacement arising from the mining excavation at the Torigatayama limestone mine in Japan has been measured by Global Positioning System (GPS). Both the regional stress state and Young’s modulus were estimated by back analysis of the change in distance between GPS stations using a 3D finite element method. It was shown that the reliability of the estimation improved with an increase in displacement due to mining progression. It was also shown that values for Poisson’s ratios of less than 0.10 are reasonable estimates with values for Young’s modulus between about 5?GPa and 10 GPa. The magnitude and direction of the maximum compressive stress in the district surrounding the Torigatayama mine were estimated to be between -6.4 MPa and -4.4 MPa and around N25E respectively.CITATION:Kodama, J, Sasaki, T, Fukuda, D, Kaneko, K, Fujii, Y and Kudo, R, 2014. Estimation of regional stress state and Young’s Modulus of ground at Torigatayama Limestone Mine in Japan, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 135–142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By L Mollison, K W. Mills, N R. P Baczynski, M F. Lee, I A. de Bruyn

This is the first of two papers concerned with rock stress inputs to various mine design issues at the large Ok Tedi open pit mine in Papua New Guinea. The companion paper (also published at this conference) is ‘The Application of Rock Stress Inputs to Stability Assessments at Ok Tedi Mine, Papua New Guinea’ (de Bruyn et al, 2014).Stresses are a required input for numerical modelling of mine design issues. However, for some operations, like the very large Ok Tedi open pit mine in remote rugged mountainous terrain, direct and representative measurement of rock stresses can be technically difficult and expensive. In such situations, development of an appropriate and sufficient understanding of rock stresses can be challenging.This was addressed for Ok Tedi by considering the following:The tectonic and regional geologic setting of the mine.Results from three different programs of rock stress measurement over 19 years, including hydraulic fracturing (1991), acoustic emission (2007) and overcoring (2010). Some interesting results of the overcoring work are discussed. It was done in a 4 km long drainage tunnel, which intersected a thick monzodiorite intrusive that has metamorphosed contacts to host contact Ieru Formation siltstones; anomalously low horizontal stresses were measured within the monzodiorite.Compilation of rock stress measurements from other New Guinea mines and prospects, both in Papua New Guinea and Indonesian West Papua.Comparisons between the variable Ok Tedi rock stresses and similar data from other porphyry copper deposits.CITATION:Lee, M F, Baczynski, N R P, Mills, K W, de Bruyn, I A and Mollison, L, 2014. Rock stresses at Ok Tedi, Papua New Guinea, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By F M. Weir, M Fowler

A discrete fracture network (DFN) approach involves numerical modelling that explicitly represents how defects may be spatially distributed through a rock mass. A DFN is a 3D realisation of the ‘smaller scale’, non-deterministic defects; it is not an attempt to model larger, deterministic structures that should be identified as part of an engineering geology model. The approach utilises structural data in stochastic analyses to give a range of possible models that provides a tool for visualisation and analysis of a rock mass and indicates the potential large-scale slope or tunnel performance and stability.Stochastic fracture modelling for rock mass characterisation has significantly advanced over the past 25 years. With recent improvements to field data collection and computational power, it has become recognised internationally as a valuable tool for modelling some geomechanical problems encountered when designing excavations in fractured rock masses.This paper provides an introduction to the DFN approach, particularly the necessary input parameters and derivation of these from typical structural data sources, such as boreholes or scan line mapping. Of particular importance for engineering applications is validation of the simulated fracture network and techniques for doing so are discussed here.CITATION:Weir, F M and Fowler, M, 2014. An introduction to discrete fracture network modelling and its geotechnical applications, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 435–444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D Carroll

Mining of the zinc, lead and silver deposit at the Broken Hill Southern Operations site has been occurring for over 100 years. As a result of this, a significant amount of high-grade ore is now taken from narrow remnant pillars left between old stopes and zones of previously mined ground. Stopes have been filled with either hydraulic fill (also known as ‘sandfill’), cemented hydraulic fill (cemented sandfill), waste rock backfill or a mixture of these fill types.In the last ten years, there has been considerable success mining through narrow pillars where sandfill is exposed in the development face and/or walls using a ‘shell’ support regime, wherein a layer of bolted mesh is sandwiched between two layers of sprayed fibrecrete (25 mm fibrecrete, then mesh and bolt, followed by a final 50 mm layer of fibrecrete). Shell support is also used in very poor, broken, relaxed ground conditions and in areas filled with cemented fill (sandfill with a minimum four per cent cement content).The next stage of innovation has been to develop a technique for mining through old stope voids filled with uncemented sandfill, known locally as ‘contours’ (old cut-and-fill working), an activity where unconsolidated sandfill can run at the face and from the backs. The challenge is to prevent exposed sandfill in the face and the backs from failing before it can be supported.To achieve this, the Southern Operations mine has implemented a technique in which 6 m long spiling bars are used to strengthen and stabilise the sandfill in front of the face. The hollow steel bars are driven in around the heading perimeter in a closely spaced pattern then pumped full of grout. The bars and the grout stabilise the sandfill in front of the face, preventing it from failing into the drive during excavation and prior to further support being installed.A final support system consisting of shotcrete, mesh, bolts and steel girders is installed as excavation progresses. Both the initial and final support systems are essentially passive support systems designed for a low-stress environment (as the stress originates mostly from the mass of unconsolidated sandfill).This process is slow and labour intensive. Fifteen separate cycles of people/machinery are needed to progress one equivalent heading cut (compared to six for a standard fibrecrete- and bolt pattern-supported rock face heading). This slow pace introduces scheduling challenges, but the process opens up parts of the orebody that were previously uneconomical to mine.CITATION:Carroll, D, 2014. Mining through sandfill using spiling bars, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By P Craig, I Canbulat, J Naylor, J Emery, A Sykes

Longwall mining is by far the most common method of underground coal extraction in Australia. Industry trends and expectations are placing increasing emphasis on the reliability and productivity of these operations. Longwalls are becoming wider and longer while retreat rates are continuously increasing due to significant improvements achieved in longwall equipment reliability and automation. This increased longwall productivity is placing significant emphasis on the reliability of longwall panel development.Although there have been significant improvements in the reliability of continuous miners and hydraulic drill rigs, the traditional resin-encapsulated bolt installation is still the principal method used in all major coal producing countries around the world. Anglo American realised that an opportunity existed to introduce an alternative roof bolt installation technique called ‘spin-to-stall’ (STS) into Australia. STS was first introduced by Anglo American Coal in South Africa, where it has been successfully used for over a decade, though implementation of South African STS resin in Australia has proven to be near impossible. Therefore, a new STS development project was initiated between Anglo American Coal and Jennmar Australia. This paper summarises the journey of this project, the results achieved and the successful implementation of STS at Grasstree mine.CITATION:Emery, J, Canbulat, I, Craig, P, Naylor, J and Sykes, A, 2014. Development and implementation of spin-to-stall resin at Anglo American’s Australian Underground Coal Operations, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By B J. Wight, R Mackay, S Kim

Improving the understanding of the processes governing ground movements in and around brown coal open cuts is of significant interest for both operating stability and rehabilitation. Brown coal, lignite, is a low-rank coal that is best described as a soft rock, with geotechnical characteristics that derive from its organic origin. It is well-known that low-rank coals exhibit creep behaviour; however, little has been reported on the impacts of chemical processes on brown coal creep behaviour even though organic substances are susceptible to chemical alterations and mining processes will contribute to changes to the geochemical environment; around most mines, groundwater flow patterns are altered leading to enhanced surface water infiltration. Here we study the deformation behaviour of brown coal in response to ion exchange reaction. Our experimental results show that for different ion exchange conditions different characteristics of secondary compression are observed. With the addition of Ca2+, the ratio between coefficients of secondary and primary compression (Ca /Cc) initially decreased, presenting a minimum value at the concentration of 0.005?M, then increased significantly. This implies the importance of ion exchange process for the long-term deformation of brown coal. On the other hand, increasing Na+ concentration did not affect Ca /Cc values significantly over all tested concentrations. The suppression of diffuse double layer was still observed for Na+-treated samples as increasing Na+ concentration decreases Ca values. From a practical perspective, this study did not consider the tertiary creep behaviour and eventual creep failure.CITATION:Kim, S, Mackay, R and Wight, B J, 2014. Creep due to chemical alteration of rocks – a case study in brown coal, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 61–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M Sandy, A Vakili, J Albrecht

Although rock strength anisotropy is a well-known phenomenon in rock mechanics, its impact on geotechnical design is often ignored. No widely accepted guideline currently exists for its characterisation. Anisotropy can significantly control the failure mechanism and progression of damage into the rock mass, particularly in high-stress conditions. As such, it can play a key role in the stability of underground excavations and subsequent geotechnical design.This paper introduces the concept of anisotropy at both intact and rock mass scales. It then presents guidelines for measuring anisotropy and assigning rock mass strength properties. An improved unified constitutive model (IUCM), which can account for more complex failure mechanisms, is then briefly described. This IUCM is used to better understand the typical responses of anisotropic rocks to underground mining and to develop an improved damage classification scheme for these conditions.The application of conventional design methods in anisotropic conditions is shown to lead to significant errors. Two case histories are then presented, illustrating how the proposed methodology can improve the reliability and accuracy of the geotechnical analysis when compared with conventional design methods.CITATION:Vakili, A, Albrecht, J and Sandy, M, 2014. Rock strength anisotropy and its importance in underground geotechnical design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 167–180 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D J. Kilkenny, D A. O’Toole, P B. Hills, K L. Seah

An investigation was undertaken to critically analyse the use of fibre reinforced shotcrete (FRS) for a variety of applications in large diameter shafts. Those applications included the use of FRS with or without the addition of subsequent rock bolting in the temporary support cycle prior to the installation of a permanent lining, most likely cast in situ concrete or as the final lining medium.Numerous authors have considered the early re-entry and strength characteristics of FRS in recent years. The current study has investigated the practical application of the recommendations of many leading authors in an endeavour to establish practical and acceptable risk-assessed procedures for the use of FRS for rapid, safe, efficient and cost-effective shaft sinking.Shaft sinking is regarded as a specialist and potentially higher risk activity due to the confined work environment, exposure to ground conditions and a high degree of manual handling associated with getting materials to the sinking face. The use of robotically applied FRS as a primary lining in shaft sinking has significant safety advantages in reducing manual handing associated with mesh safety support and bolting, as well as reducing direct exposure to ground conditions.The study involved both field testing and a literature review. The study established an initial set of criteria for the use of FRS in the development of large diameter shafts and demonstrated a number of scenarios where the technique of robotically applied FRS provided significant safety and cycle time advantages. The opportunity for a fully sprayed single pass lining was also investigated as part of the project.CITATION:Hills, P B, O’Toole, D A, Kilkenny, D J and Seah, K L, 2014. Exploring the use of fibre reinforced shotcrete in large diameter shafts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By F Sandrone, J-P Dudt, J Zhao, E Paltrinieri

Tunnel boring machines (TBMs) excavation is nowadays more and more considered a valuable alternative to conventional tunnelling. As a matter of fact, thanks to its advantages such as greater rate of advance and safer working conditions, the application of TBMs has increased significantly in recent years. Despite the possible excellent performance of TBMs in favourable ground conditions, the advance rates could be significantly slowed down or even obstructed in limiting geological situations. This obviously traduces in potentially longer tunnel construction times and higher costs and, therefore, in a preference for conventional method. One of the major geological hazards encountered during tunnel construction, is related to the presence of fault zones or heavily jointed and fractured rocks. The most common geotechnical problems resulting from tunnelling in these difficult conditions include the instability of the excavation face, instabilities of side-walls producing large overbreaks on the tunnel profile, excessive deformations in case of squeezing grounds, frequently changing stresses in terms of magnitude and direction, high water inflows, etc. The decisions aids for tunnelling (DAT) is a model and a computer code that can be used to evaluate the influence of the uncertainties related to both the geological/geotechnical conditions and the construction process on final tunnel construction time and costs. In this framework, the DAT is used for assessing the effects that challenging ground conditions may have on tunnelling operations in terms of costs and delays. This is done by simulating the tunnel construction considering several geological profiles. The aim of the study is comparing different excavation methods (ie drill and blast versus TBM) in changing ground conditions along the tunnel alignment ranging from good rock, to very poor and fractured formations. The results show the impact, in terms of changing construction time and cost, of the excavation method versus the ground conditions.CITATION:Paltrinieri, E, Dudt, J-P, Sandrone, F and Zhao, J, 2014. Comparison of excavation methods in different ground conditions with the decision aids for tunnelling, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 573–580 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By S J. Clarke, C S. Walker

The South West Rail Link (SWRL) project involved construction of a rail line to service new residential areas in south-west Sydney. The 11 km rail line is conveyed through a short tunnel at shallow depth where it crosses beneath the eight lanes of the Hume Highway. The underpass location is one of the most heavily trafficked within Sydney’s motorway network.The New South Wales Roads and Maritime Services (Roads and Maritime), as the owner of the highway asset, had the responsibility of managing the risks to the highway and traffic associated with the tunnelling project from the pretender stage through to completion. This paper considers the primary risks and mitigation measures employed, including geotechnical investigation, and development of appropriate construction constraints and concept design of an extensive real-time survey system to monitor pavement deformation during the tunnel works.The geology comprises fresh Minchinbury Sandstone in the tunnel invert and side walls, and variably weathered Bringelly Shale in the haunch and crown. Few tunnels have been excavated in these rock types in Sydney, and there is little information relating to the in situ stresses and stress-relief deformations in these materials.During tunnel construction the monitoring data indicated unexpected surface heave of up to about 24 mm. A multiparametric back-analysis of the deformation data is presented, which provides information on the deformation mechanisms and key geotechnical parameters, including rock mass modulus and in situ stresses.The approaches and methodologies developed for the SWRL underpass were effective in maintaining the safe operation and traffic capacity of the highway throughout the construction period, and the analysis of the monitoring data provides a useful reference for similar future projects, or projects constructed in similar ground conditions.CITATION:Clarke, S J and Walker, C S, 2014. Deformation mechanisms of the South West Rail Link underpass beneath the Hume Highway, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 631–640 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By I Gray

While in some cases it is vitally important to measure the virgin stress in rock prior to tunnelling there are a number of cases where such stress measurement is really not required. The concept of having to have a number to put in a numerical model representing a continuum is often quite inappropriate. This paper discusses the cases when virgin stress measurement is required and the most appropriate means to measure it. The techniques discussed cover all of the overcoring systems, hydrofracture and borehole breakout measurements. It also covers the use of rock surface stress measurement, which is easy to perform and should be used to check for changing stress conditions. Unfortunately this technique has been ignored in recent times because engineers are addicted to numerical models requiring far field stresses rather than measuring the real values that exist where they matter – at the tunnel wall. A case is presented in which the measurement of surface stress in a tunnel boring machine tunnel enabled the far field stress to be determined in what must be the world’s largest overcore.CITATION:Gray, I, 2014. The measurement of rock stress for tunnelling, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 153–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By T J. McGavin

This paper examines the fire life systems implemented in two existing tunnels and discusses whether the standards used were appropriate. It focuses on the Terrace Tunnel as this upgrade and refurbishment is complete.The New Zealand Transport Agency (NZTA) manages six tunnels on the State Highway network with two of these built in the last seven years. The Terrace Tunnel, opened in 1978, was refurbished with modern fire life safety systems in 2010–2012. An interim upgrade of the Mt Victoria Tunnel, opened in 1931, was also carried out at this time.In present times, few existing tunnels have undergone significant upgrades and refurbishments. The Terrace Tunnel required: new power supplies, control buildings, lighting, wall panels and jet fans, a deluge system, emergency exit lights and way-finding lights, a public address (PA) system, a radio rebroadcast system, lane control sign (LCS) and variable message sign (VMS), an over-height detection system (OHD) and a new tunnel management system.In the absence of suitable guidelines, various standards were used to carry out the refurbishment. The Austroad Guide to Road Tunnels and AS4825 Tunnel Fire Safety, although designed for new tunnels and not specifically intended for existing tunnels, provided a framework. A multi-criteria assessment of risk (MCAT) was carried out to determine the systems to be provided.The Terrace Tunnel has perhaps set a benchmark for refurbishing existing tunnels as few projects of this type have been completed recently. This paper examines the process and the outcomes.CITATION:McGavin, T J, 2014. The refurbishment of the Terrace and Mt Victoria Tunnels, Wellington, New Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 87–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A L. de Ambrosis, F M. Weir, M Fowler

Traditional kinematic and statistical analyses of geological structure for geotechnical engineering applications, while considered industry standard practice, have some limitations and unrealistic assumptions. An improved approach involves a discrete fracture network (DFN), a numerical model that explicitly represents how defects may be spatially distributed through the rock mass. The DFN technique utilises the structural data in stochastic analyses to give a range of possible models used for visualisation and stability analyses.The early development of the DFN approach was largely associated with modelling fractured hydrocarbon reservoirs and nuclear waste isolation programs. With recent improvements to computational power it has become recognised internationally as a valuable tool for modelling some geomechanical problems encountered when designing excavations in fractured rock masses. For tunnelling or slope stability projects DFN modelling provides visualisation of a rock mass and identification of likely failure mechanisms.This paper presents a suite of DFN modelling undertaken for the design of a tunnel within the Ashfield Shale unit of the Sydney Basin, Australia. The necessary input parameters and derivation of these, along with the importance of both an accurate engineering geology model and validation of the synthetic fracture network are demonstrated. Multiple realisations of the DFN were analysed to provide an indication of the number and volume of unstable blocks for the proposed tunnel geometry, enhancing support design. One fracture network realisation was sliced along multiple sections for use in finite element modelling.CITATION:Weir, F M, de Ambrosis, A L and Fowler, M, 2014. Discrete fracture network modelling for tunnel design in the Sydney Basin, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 219–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A Harding, M Chappell

Precast concrete segmental linings have enjoyed widespread use around the world, and are the lining type of choice for tunnels constructed using a shielded tunnel boring machine. However, there is significant variation in the design of such linings from one country to the next in such areas as materials, geometry, fixtures and fittings, waterproofing and reinforcement to name but a few. This arises because the speed at which the technology has developed within some countries and regions has sometimes outstripped the transfer of such technologies to the rest of the world.This paper provides some insights into the variations in lining design in different parts of the world with the aim of providing designers and constructors alike a reference for the different methods adopted. It provides a context for these developments by briefly summarising historical reviews of this subject before looking at some of the developments around the world over the last 15–20 years. The developments are presented with some reference to the reasons for implementation, and the advantages and limitations commented on. Following on from this description of the state-of-the-art, the authors also provide their own views on what developments we may see in this area in the near future.CITATION:Harding, A and Chappell, M, 2014. Precast concrete segmental tunnel linings – the state-of-the-art, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D A. F Oliveira, C J. Parker

The role of the virgin in situ stress field in tunnelling projects is well known in the Sydney area. The effect of in situ stresses is mostly considered through the use of published relationships that describe the in situ stress conditions as a function of depth. Considering the significant scatter in the data, it is evident that by adopting such relationships, the designers are assuming an average distribution of stresses with depth that is generally a reasonable engineering approach; however, when building a geomechanical model, the tunnelling or geotechnical engineer needs to account for the interrelationship between ground conditions (rock mass quality – fracturing, strength and stiffness) and in situ stress, which may explain part of the stress data scatter. This paper presents an alternative approach for interpreting in situ stress conditions, valid for both Sydney sandstones and shales that focus on such interrelationship between in situ stress and ground conditions.CITATION:Oliveira, D A F and Parker, C J, 2014. An alternative approach for assessing in situ stresses in Sydney, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 189–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By B Chapman, R Nievergelt, J Hill

A major component of Sydney’s new South West Rail Link project is the Hume Highway Underpass (HHU), an 80 m long twin track mined tunnel excavated at a depth of just 5 m below the pavement of the Hume Highway; one of Australia’s busiest road corridors.In order to ensure a safe and efficient construction of the underpass without disruption to the Hume Highway traffic, design of the HHU required specific focus on the prediction and control of ground movements. This paper describes the design and construction solutions adopted in response to these challenging constraints. The paper also provides discussion on the observed behaviour of the underpass during construction and the results of a back analysis that was undertaken during construction.CITATION:Hill, J, Nievergelt, R and Chapman, B, 2014. Design and construction of Sydney’s South West Rail Link Hume Highway Underpass, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 375–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G M. Taylor

The application of high technology to monitor and control fire life safety, critical functionality in tunnels and underground spaces generally has progressed at an ever accelerating rate over the past decade. Today these systems comprise some of the most complex and little understood aspects of the tunnel/underground facility construction industry, with this area being perceived as high risk comprising impenetrably complex ‘black box’ technology covered in blinking LEDs. This paper will seek to explode some urban myths and common misconceptions associated with such systems, providing its intended audience with a review of what all this technology comprises and where the real risks lie in its delivery lie.The author contends (and looks to support such contention via this paper) that by applying baseline project and risk management processes to the procurement of this widely misunderstood black box technology, the quality of the final outcome can be much improved, driving innovation, reducing both cost and significantly mitigating delivery risk.CITATION:Taylor, G M, 2014. Procuring control and intelligent traffic systems for major new build projects – avoiding pitfalls and maximising value, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J Rostami, T Afshar, M Sharifzadeh

Accurate estimation of rock load and selection of types of ground reinforcement to match post-failure behaviour of rock mass are important issues to assure tunnel stability. This paper focuses on the main factors affecting rock load to evaluate the capabilities of the existing models for prediction of rock load. Rock mass properties, project features and excavation method, as well as ground conditions and stress condition were found to be the key factors affecting the magnitude of rock load. Field data from tunnels of about 37.5?km driven in several geological structures in non-squeezing ground was used in this study. An in depth statistical analysis was performed on data to find correlations between the input parameters and measured/observed rock load. A weighting system was proposed to obtain the proper contribution of each factor for estimation of rock load in tunnelling through various ground conditions. The new classification system offered predicted values for rock load that were in a good agreement with the actual field measurements. The high disturbance factor (D>0.4) was the prime factor which controlled the rock load. Rock mass quality was the second key factor influencing rock load, which could be estimated by GSI, GSIresidual , especially when combined with tunnel depth.CITATION:Afshar, T, Sharifzadeh, M and Rostami, J, 2014. Estimation of rock load for tunnels with different disturbance factors, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014