Search Documents

By Winton J. Gale

The subsidence over a longwall panel at Tahmoor Mine in the Southern Coalfield of NSW, Australia, was found to be approximately twice the size it had been in previous measurements. An investigation into the potential causes was conducted using computer modeling together with hydrological characterization and detailed geotechnical characterization of the strata. The abnormal subsidence was found to be consistent with localized weathering of joint and bedding planes above a depressed water table adjacent to an incised gorge. The study showed that other factors such as variation in stress field, joint zones, variation in rock strength and topographic factors did have sufficient impact to induce the abnormal subsidence. The results have significant implications to subsidence prediction in areas that may be prone to the phenomenon found at Tahmoor. Key indicators of the potential for this form of abnormal subsidence are presented.

Jan 1, 2011

By N. J. Rarmrez, C. Perez, J. D. Calderon, L. Lopez

"Among the thermal characterization of any material, one of the variables to know is the coefficient of thermal conductivity because this value can tell how much heat passes through the material and if the material could be used as an isolator. In order to determine this parameter is required some kind of special equipment and controlled conditions which implies high costs in the development of tests. The present paper proposes a design of a low cost measurement system in order to determine this coefficient with the lower possible error. This equipment was thought for companies or labs where they do not have the economic resources or the infrastructure (environmental controlled labs, heat flux transducers, human resources with specialized knowledge) to do this kind of tests.The system is based on ASTM C 518 - 04 [l] and integrated by two plates (one that contains a thermal resistance and which temperature is controlled by a closed loop controller and the other one with a route of water flow). The thermal resistance is actuated by a relay and a supervisor system checks the total time the relay is on in order to determine the effective power applied to the system. The contact faces of the plates contain a group of temperature sensors connected to a data acquisition system that process and record the temperature in each measurement point.With the power applied to the system, the measurement of temperatures and a process of calibration is possible to determine the coefficient of thermal conductivity. IntroductionWithin the thermal characterization of a material of known variables is the coefficient of heat transfer, since this value can know the amount of heat the material is capable of transferring or isolating. To determine this ratio requires specialized equipment and controlled conditions, which implies high costs in the development of a test. This article proposes a design of a low cost machine to allow closer this coefficient with the least possible error. This equipment was done thinking about companies that do not have the infrastructure (laboratories, controlled environment, heat flux sensors, human resources expertise) and financial resources to conduct these tests."

Jan 1, 2011

By Onder Guney, Erdem Demirkesenm

"In this study, the crystallization behavior and thermal expansion coefficient of a lithium disilicate (LS2) based glass-ceramic derived from SiO2-Li02-AhO3-K2O-ZrO2 system was investigated by using x-ray diffraction (XRD), high temperature x-ray diffraction (HTXRD), differential thermal analysis (DTA) and dilatometer techniques. Analytical reagent grade chemicals were chosen as raw materials for preparing glass batches. Nucleation and crystal growth heat treatments were planned according to DTA results. The amounts of the amorphous and crystalline phases developed during the heat treatments were determined by quantitative XRD. XRD results of crystallized samples showed simultaneous formation of lithium silicate (LS) and quartz in the early stage of the crystallization followed by formation of lithium disilicate (LS2) at higher temperatures. The thermal expansion coefficients of glassceramics were also measured depending on the applied heat treatments.IntroductionSignificant developments occurred in all ceramic materials provide the fabrication of high quality dental implants [1]. Glass ceramic based dental restorations like dental inlays, crowns, bridges and veneers are becoming increasingly popular with their reliable and durable performance [2,3]. In addition to their advanced functional properties, glass ceramic implants especially lithium disilicate glass ceramics also face the esthetics expectations of patients and dentists and in this way they are starting to take the place of metal based restorations today [1,3,4,5]. Lithium disilicate glass-ceramics derived from multicomponent glass systems have some superior mechanical and optical properties comparable to natural teeth [ 6]. In restorative dentistry, mechanical characteristics of biomaterials play very crucial role in order to resist the masticatory forces occurred during biting and chewing [7] According to three point bending test results of Roland, flexural strength of the lithium disilicate glass-ceramics were 400±40 MPa and their fracture toughness (K1c) are approximately 3,3 MPa m112 [2,6]. In addition to high mechanical strength, aesthetic appearance is another important prerequisite as material for dental restorative applications. Translucency and light transmission of the LS2 glass ceramics mimic enamel. Moreover, opacity of the material can also be adjusted depending on the restoration types [2,6, 7]. These superior properties of the LS2 glass ceramics are directly related with chemical composition of the base glasses and controlled crystallization heat treatments [ 4, 7]. The aim of the present work is to determine the effect of heat treatment schedules on the crystallization behavior and thermal expansion of the LS2 glass-ceramics."

Jan 1, 2011

By W. Hardtke, B. Perry

Model reconciliation problems at the low-grade, high-nugget Phoenix gold-copper deposit led to an examination of the influence of production decisions on ore-waste classification. A conditional simulation study of the deposit was used as the basis for: 1) quantification of dilution at different bench heights, 2) quantification of ore-waste misclassification relative to bench heights and cut-off wades, and 3) determination of an appropriate number of samples to optimize ore-control polygon definition. Actual reconciliation data were empirically used to support conclusions. Simulations of both gold and copper were combined through net revenue modelling. These simulations increased understanding of the nature of the deposit and provided insight for resource modeling and mine planning.

Jan 1, 2011

By Guangchun Yao, Chuan Li, Hongjie Luo, Zhuokun Cao

"The expansion rate and collapse time of liquid aluminum foams are essential for the determination of operating time and quality of the resulting foam. In the present paper, liquid aluminum foams was fabricated by adding in TiH2 as blowing agent, and the variation of expansion rate with foaming time was non-contact detected by a laser distance measurer. The influence of different stabilizing agent and alloying elements was studied. The results show the fact that the fraction of stabilizing agent only perform little effects on the maximum expansion rate of liquid aluminum foams, while the influence of alloy elements are remarkable. The maximum expansion rate would increase much when Mg is added, and the liquid foam also collapse at a shorter time. Comparison was made between experimental results and mathematic calculations, which reveal the fact that it is the change of TiH2 decomposition responsible for the change.IntroductionMetal foams, combining light weight with other unique mechanical and physical properties, have gained wide interest and been developing fast during past few decades. However, manufacture of this new material is quite challenging since it involves simultaneous occurrence of gas, liquid and solid phase at high temperature [1-2].Quite some manufacture routes have been developed for manufacturing metal foams, and the structure and quality of resulting foam are remarkably improved during the last decades. However, most of the past works seems to be experiential, and because the lack of basic knowledge of foaming process, the start material is limited and the production technologies are far from reliable and reproducible.[3-4]In direct foaming process, decomposition of blowing agents, TiH2 for example, is the main force for foam expansion. The density and foam structure changes with time during the foaming process, so it is expected that foams of certain structure can be obtained by solidification of the liquid foam at a certain time [5-6]. However, the foaming process is weak in reproducibility and the influence of stabilization additives and alloying elements is unclear."

Jan 1, 2011

The process of gold recovery by gravity concentration is incorporated in the metal recovery flowsheet at seven Newmont Mining Corporation owned mining operations in Australia, North America and Africa. In 2009 gold recovered by gravity processing was equivalent to nine percent of Newmont's total gold sales of 5.3 million ounces. This paper will discuss these applications in detail including a review of plant flowsheets and presentation of recent operating results. Operating performance will be discussed with reference to ore characterisation procedures, interpretation of results, design considerations and optimisation practices as they relate to the recovery of gold by gravity concentration.

Jan 1, 2011

By B. Wasmund, B. Haneman, G. Sheehan

Success in implementing new technology for metallurgical processes is not a foregone conclusion: This paper includes a survey of 23 new technology-based metallurgical plant start-ups, in which the authors have identified 7 successes, 9 difficult start-ups, and 7 failures. Success is defined not only as meeting the schedule and budget to the end of mechanical completion; the key goal is a fast ramp up to the full design production level, with minimum plant and equipment modifications required after start-up. This paper sets out the key factors that underlie achievement of a quick production ramp up curve, as determined from the authors' project experiences and a quantitative analysis of over twenty metallurgical plant start-ups, both pyrometallurgical and hydrometallurgical. Thorough test-work and pilot plants, plus appropriate scale-up to the full commercial plant, are key determinants of success in implementing new technology in metallurgical processes. Another critical factor is the number of new elements and their interactions. Project phasing is also particularly important for new technology projects, with appropriate review after each phase to develop a risk mitigation plan for the subsequent phase. New technology projects need committed champions to advance the project in the face of sceptics, but also require dispassionate and unbiased experts to ask the hard questions. As a project evolves, it is important to periodically question the appropriateness of assumptions, as well as to re-assess the relevance and completeness of data from test-work I pilot plants I industrial analogues. Sufficient human and financial resources are required to complete the often arduous implementation phase. During the ramp-up period, the operation generates little positive cash flow; however, significant expertise and capital are required for the de-bottlenecking projects that are often necessary to reach the plant's design output level.

Jan 1, 2011

By W. van der Merwe

With the gold industry looking to process more complex ores, the online measurement and control of cyanide addition to the gold leaching circuit has become more crucial. This paper compares the two commonly employed "free" cyanide online analysis methods (amperometric and potentiometric end-point silver nitrate titration) with the common site laboratory rhodanine endpoint silver nitrate titration and ion selective electrode methods. Measurement differences between these methods are presented and discussed for cyanide solutions containing copper and zinc with varying cyanide to metal ion ratios. The resulting cyanide available to leach gold is also compared with these measurements.

Jan 1, 2011

By Chris Howell

PotashCorp?s Aurora phosphate mine, in Beaufort County, NC, operates four low pressure boilers and four high pressure boilers to meet its process steam requirements. Maintaining these boilers is critical to meeting production demands. Processing phosphate ore into phosphoric acid requires large amounts of sulfuric acid and steam. Ore is mined from the phosphate deposit with large bucket excavators after 9 to 30 m (30 to 100 ft) of overburden is removed. The phosphate ore is mixed with water to make a slurry that is pumped to the mill. Elemental sulfur is burned in the presence of air to make sulfuric acid. This process is highly exothermic and boilers produce steam while cooling the process. The phosphate ore is reacted with sulfuric acid and the resulting products are refined into different grades of phosphoric acid for fertilizers, feed stock and food additives. Plant operators at the mine were challenged with boiler feed water that was high in silica and other contaminants. As a result, boiler operations were experiencing difficult, labor-intensive operations and equipment deterioration. This resulted in higher operating costs and diminished processing performance. The facility was operating an aged boiler feedwater pretreatment system that included warm lime softening followed by pressure filtration and a cation/anion/mixed bed demineralizer system. The demineralizer required frequent regeneration and chemical usage was high and costs were difficult to predict. Depressurized well water (DPW water), used for plant utility water and boiler makeup, is very high in silica, in the range of 60-70 ppm. Silica can form scale at pressures below 600 psig. Above 600 psig, silica starts to volatize, carrying over with steam to potentially form deposits on downstream equipment and processes. Mine officials decided to upgrade the boiler feedwater pretreatment system to a state-of-the-art reverse osmosis (RO) membrane system. This new system, which started up in March 2009, has improved operating performance and reduced water consumption and overall operating expenditures.

Jan 1, 2011

Choosing the right valve for corrosive, abrasive slurry applications requires exacting analysis and a comprehensive understanding of the complete slurry process. Within the realm of flow control in abrasive and corrosive slurry applications, there is no room for a one-size-fits-all approach. To ensure minimal maintenance, maximum uptime and the lowest overall cost of ownership, the slurry processing toolbox must contain countless alloy and elastomeric pairings ? each carefully targeted to the particular process medium and conditions. This materials selection process is best tackled by turning to expert slurry application engineers and valve product managers who work closely with customers to specify the optimal valve for the given parameters. ?When plant operators and design engineers apply conventional valves in abrasive applications or use metal seated valves or simply apply the wrong valve for a particular flow control situation, it typically leads to rapid valve failure, the potential for hazardous leakage, unexpected shutdowns and costly downtime,? said Cal Cobb, valve products manager for Weir Minerals North America, manufacturer of Isogate slurry valves for service in mining, minerals processing and metallurgical environments.

Jan 1, 2011

By Abraham Lindo

Taboguilla is a small island located 10 miles outside the Panama Canal Pacific Entrance. In 2002 a fuel distribution facility was installed in order to supply fuel to vessels passing thru the canal. The current capacity of the tank farm is equivalent to 1,100,000 barrels. The demand for marine diesel at this location still exceeds the current capacity, thus an expansion project is currently underway to increase the available space for diesel tanks. There is a total of 800,000 cubic meters to be excavated in order to create the new space. 400,000 cubic meters of that total is basalt rock which will need to be blasted

Jan 1, 2011

By Rocky Wu

Rock bursts are one of the greatest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost-effective yielding rock bolt. This paper introduces a new yielding rock support: the Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150?250 mm (6?10 in) of deflection at 8?10 metric tons (MT) (7.9?9.8 t) loads for every 16.4kJ (12,096 ft lb) energy input. The bolt?s performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described; the dynamic testing results are discussed; and the features and application of the bolt are presented.

Jan 1, 2011

By Brian R. Zelenka

The Bureau of Mines (Bureau) reviewed all available information regarding geologic and depositional processes contributing to potential coastal and offshore platinum group metal (PGM) placer deposits around the Goodnews Bay Mining District. The Bureau found that favorable environments for PGM along with gold and chromite enrichment include: (1) buried paleofluvial channels; (2) recent paleofluvial channels with little marine sediment overburden, (3) beach deposits, particularly in the upper swash zone and near back beach environments; (4) paleostrand lines; (5) shoal lag deposits inside the mouths of Goodnews and Chagvan bays; and (6) bases of far offshore tidal ridges which may represent reworked glacial deposits. Limited geologic and compositional (assay) data prevent determination of deposit size and grade of PGM mineralization for each deposit class. Future geologic sampling requirements for demonstration of identifiable offshore and beach PGM-bearing placers are discussed. Beach and offshore sampling programs conducted by the Bureau in 1986 will contribute additional information providing verification of specific deposit classes.

Jan 1, 2011

By A. Warczok, C. M. Diaz, A. Bergman, T. Utigard, M. Barati

The world wide consumption of energy is steadily increasing and by 2030 it is forecasted to grow by another 50%, leading to mounting political and economic pressures. For any pyrometallurgical operation, it is therefore paramount to investigate and implement methods to decrease the use of energy. In the pyrometallurgical processing of steel, copper, nickel and other high temperature metals, a large amount of energy is lost in hot off-gases, molten slags, mattes and molten metals. Most of this energy is generally lost during the cooling and solidification steps with very little focus on energy recovery or reuse. In this paper we will quantify how much energy is contained in the various slag streams, then review previous attempts and methods employed to recover some of this energy, and finally evaluate some novel technologies that could potentially be employed.

Jan 1, 2011

By Lawrence Lien

The reduced need for traditionally trained and educated personnel in the mining industry is systemic to the changing mining industry. Universities and other training institutions are meeting the traditional skill needs required by the industry, but are the skill needs going to be the same in the near future? The answer may be no. Mining is changing because of increased liabilities and costs of environmental and safety is-sues; lower grades of minerals in traditional mining activities and the advent of new bio-chemical processes and robotic equipment. More productive and economic alternatives, and larger, more sophisticated and automatic equipment, are also changing the industry. Engineering is more specific, accurate, precise and expensive. Measurement is more thorough and timely of progress, production, costs and productivity. And, the industry will likely be engaging in more undersea mining, possibly space-based processing, less human interaction and more remote control of events than was previously thought possible.

Jan 1, 2011

By Gerald E. H. Verbeek

As the number of driven concrete piles with Embedded Data Collectors increases, it has become possible to compare the widely used Beta Method to assess pile damage (using the change of pile impedance) with the so-called Measured Pile Integrity (MPI) method (a combination of two approaches using both the change of pile impedance and the change in pile pre-stress levels). After a brief introduction of both methods, this paper presents the outcome of that comparison based on data from more than 400 concrete piles driven in Florida, which brings into question the reliability of any damage assessment method based solely on the change of pile impedance (such as the Beta Method), especially to detect damage near the pile toe. Moreover the paper demonstrates the need to re-assess the damage classification used for the Beta Method as well as the use of Pile Driving Analysis (PDA) to detect pile toe damage.

Jan 1, 2011

By Hylton McWhinney, Doanh Tran, Jewel Andrew Gomes, George Irwin, Sameer Pallavkar, Md Islam, David Cocke, Mohammad Rafiqul Islam

"High-performance nickel-based nanocrystalline zinc oxide adsorbents have been prepared adjusting Ni/Zn mol ratio of 1 :5 by thermal decomposition, coprecipitation and sol-gel method for selective adsorption of thiophene in liquid hydrocarbon fuels at ambient temperature and pressure. To understand the nature of reactive adsorption of thiophene (C4H4S) on Ni/ZnO, the effect of preparation techniques, morphological and textural structure on the desulfurization activity was investigated. A model fuel (20 mL) consisting of pentane (C5H12) and thiophene was prepared and adsorption experiments were performed by a batch method under ambient conditions. The physicochemical behaviors of the fresh adsorbents were obtained using X-ray diffraction (XRD) with EDAX, scanning electron microscopy (SEM). The sulfur concentration in the mixture was monitored by UV-vis spectrophotometry. The adsorption reaction confirmed that ZnO played a crucial role in taking up S element to convert it into ZnS. The deposition of nickel on ZnO is an innovative approach which takes advantage of the selectivity of Ni towards S-species and the high adsorptive capacity of ZnO support.IntroductionLow temperature deep desulfurization of fuels via selective adsorption of sulfur compounds keeping coexisting aromatic hydrocarbons and olefins intact is receiving increasing attention in the research community worldwide in order to satisfy the upcoming environmental regulations and fuel specifications. The sulfur compounds in the transportation fuels is a matter of concern when global crude oil slate is becoming heavier and sourer and environmental restrictions on both the refining process and the refined products are becoming more stringent. According to the current refinery technologies, the sulfur content in refinery fuel is typically around 300-500 ppm by weight (ppmw) [1-3]. Starting in 2006, sulfur limits in highway diesel and gasoline were set to 15 ppm and 30 ppm, respectively. During combustion sulfur in the fuel are converted to toxic sulfur oxide (SOx) and contributes to air pollution and acid rains [ 4]."

Jan 1, 2011

In-Situ Leaching (ISL) process plants are low cost producers for uranium deposits where the geology is suitable. In the 1970s, a three-year pilot ISL program occurred on gold ore from the Ajax Mine, Cripple Creek District, Colorado, using a chloride and iodide solution [1]. The test was halted due to poor results. With gold and silver the international ISL progress has been slow; however the potential for low capital expenditure (CAPEX) and operating expenditure (OPEX) with large low grade deposits is real. Unless the metallurgy has been demonstrated there are significant risks which could be fatal flaws to an ISL gold or silver project. The metallurgy of gold ISL projects is far from simple and it is early days with project development.

Jan 1, 2011

By Edgar Peek

"The two dominant metallurgical problems in treating most base metal sulphide concentrates in both the chloride and sulphate system are iron removal and sulphur elimination, respectively [1-3]. In this paper the opportunities, limitations and fundamentals of the chloride metallurgy system are described against this background. Only the treatment of oxide and sulphide ores is considered. Both hydrometallurgical and pyrometallurgical unit process operations are highlighted, since most successful base metal processes are based on a combination of the two. Hence, an overview of the technical and also some economical aspects of chloride metallurgy are presented.This overview summarizes the successful applications of chloride metallurgy, but it will not give exhaustive process and plant descriptions. It predominantly focuses on the essential technical features of the metallurgical unit process operations, while providing numerous references separately."

Jan 1, 2011

By Elizabeth A. Johnson

The vaporization thermodynamics of the aluminum-silicon carbides Al4SiC4 and Al8SiC7 were studied by the Bureau of Mines over the temperature range of approximately 1,500 to 1,700 K. Vapor pressures were measured by a Knudsen effusion-mass spectrometry technique in which powdered samples were effused from graphite crucibles through small orifices. For each compound, a total of six orifice diameters was tested to verify equilibrium within the cell. Aluminum, mass number 27, was the only vapor species detected over the range 4 to 200 amu. Experimental results are based on the following equations for incongruent decomposition: A14SiC4(cr) - 4A1(g) + SiC(a,hex) + 3C(gr); Al8SiC7(cr) - 8A1(g) + SiC(a,hex) + 6C(gr). The observed vapor pressure-temperature relationships determined with a cell orifice area of 2.0 x 10-3 cm2 for Al4SiC4 and 1.81 x 10-3 cm2 for A18SiC7 are the following: Log P - (-18,682/T) + 12.476, for Al4SiC4 (1,550 to 1,643 K) and Log P = (-19,308/T) + 12.421, for Al8SiC7 (1,526 to 1,784 K), with P in pascals and T in kelvins. Third-law analysis of the data provided the following heats of formation: A14SiC4 ?H at 298.15 K - -50.0 kcal/mol and A18SiC7 ?H at 298.15 K - -92.1 kcal/mol.

Jan 1, 2011