Search Documents

By C. K. Baxter, A. Odeshi, M. Mohammadi, E. D. Cyr

"Metal additive manufacturing has been a revolutionary step in designing new complex shapes with faster and cleaner building capacity in comparison to subtractive manufacturing processes. The ability to print lightweight alloys such as aluminum has made metal 3D printing attractive to different industrial sector from aerospace to energy and bioengineering. Of particular interest in this study, are the mechanical and microstructural properties of AlSi10Mg-200°C alloys. In this project, samples were 3D-printed in horizontal direction using an EOS M290 machine by Direct Metal Laser Sintering (DMLS) technique. Uniaxial tensile tests and high strain-rate impact e tests were carried out to investigate the mechanical properties and to study the repeatability of the process. A constitutive model is developed to predict the results of the mechanical tests at varying strain rates to better understand the high strain-rate behaviour of these alloys. Using optical microscopy, features such as scan tracks and melt pools within the AlSi10Mg-200°C samples were observed, and the microstructure was observed to be homogenous. The previously listed tests were compared to the results obtained for similar cast alloy counterpart, i.e. A360.0.INTRODUCTION A relatively new way of manufacturing parts is on the increase as rapid prototyping becomes increasingly popular throughout the world. Additive manufacturing is a process which, given a 3D model, uses metallic material in powder form to build a part layer by layer until completion (Gu, Meiners, Wissenbach, & Poprawe, 2013). This way of rapid prototyping is very attractive in comparison to other possibilities because of its ability to accommodate complex design and geometries. Conventional manufacturing methods have limitations when it comes to complex geometries, but additive manufacturing allows for increased design flexibilities while maintaining a light and stable final product (Murr et al., 2012). It also allows for a reasonable cost, especially for small batch sizes that would otherwise be extremely expensive."

Jan 1, 2018

By I. I. Beloglazov, G. A. Iusupov, A. Ju. Feoktistov

"The aim of this paper is to study the numerical modeling of the crushing process in a jaw crusher with complex motion jaws using Discrete Element Method (DEM). The main goals are to ensure the conformity of numerical simulation results to the experimental data, optimize the operating modes and the crusher design and develop automated verification and calibration methodology. It is offered to use automated selection of mathematical model parameters using large- or laboratory-scale experiments instead of deriving parameters from conventional intensive material tests (e.g. drop-weight test). Experimental data were obtained from a large-scale crusher designed and manufactured by the company “Mekhanobr-Tekhnika”. Both jaws have their drive shafts located asymmetrically; one jaw is driven in the upper part, the second at the base. The crushing process involves fragmentation of single smoothed rectangular granite particles of the same weight. During the experiment, the required parameters such as particle size distribution were obtained for further computer simulations. Based on the obtained experimental data, the Rocky DEM model was built. Simulation breakage parameters were calibrated using automated parameter selection methodology based on multiple set of parameter-controlled simulations. A good correlation of the experimental data and numerical simulation data was obtained. The methodology in combination with well-known capabilities of simulation modeling will help reduce the research time in the development of new mineral processing equipment.INTRODUCTION Preparation of rock mass for enrichment includes the power-consuming processes of crushing and grinding. Initial rock mass crushing is performed by means of drilling and blasting operations. To reduce the average size of a rock piece, primary crushers, mostly jaw crushers, are further applied. The advantages of the jaw crusher are simple design, easy maintenance and repair. One of the drawbacks is large oscillating masses and, thus, high power consumption during operation (55 - 200 kW). Jaw crushing simulation will help optimize the crushing process and improve further rock transportation and processing performance."

Jan 1, 2018

By J. Fixter, P. Prangnell, Z. Pinter, E. Eimer, B. Chehab

"High deposition rate Wire and Arc Additive Manufacture (WAAM) can provide benefits to the aerospace industry, including a reduction in lead time, reduced material waste and, through higher solidification rates, refinement of the as-built microstructure relative to a cast material. However, candidate 2xxx series high strength alloys for this process normally require a solution treatment, which is problematic for large near-net-shape components, and age hardening to achieve maximum mechanical properties. With each layer being subject to multiple thermal cycles, exploiting the thermal conditions in the WAAM process to avoid post-build solution treatment is therefore of interest. A solutionisation model has been developed for the WAAM process, based on diffusion controlled dissolution using DICTRA, which was validated through thermal simulations combined with 2D and 3D image analysis. The model has subsequently been used to simulate the solutionisation behavior during a typical WAAM thermal cycle and to explore what could theoretically be achieved by, for example, refining the starting microstructure.INTRODUCTION There is currently great interest in exploiting additive manufacturing (AM) in the aerospace sector due to several benefits it can potentially provide; including reduced material waste, shorter product lead times and greater design freedom (Herzog, Seyda, Wycisk, & Emmelmann, 2016). However, with aluminium alloys the material properties obtained are generally inferior to those of conventional high-strength wrought products; therefore more research is required to explore the potential for exploiting the unique process conditions in AM to improve the as-deposited microstructure. A range of AM techniques are now available (Debroy et al., 2018), which differ in terms of the feedstock type and power source and it is necessary to match the appropriate technology to a particular application. This generally requires a compromise between the build rate and shape resolution. Wire and plasma-arc additive manufacturing involves using an electric arc to melt wire onto a substrate, and fabricates a part by building up overlapping layers of deposited weld beads (Addison et al., 2015; Williams et al., 2015). The benefits of this process over other AM methods are the much higher deposition rates (e.g. kg’s/hour) achievable and lower capital equipment costs relative to powder bed techniques, which makes it suitable for large scale applications. However, limitations include a lower part complexity, lower solidification rates and a greater need for post-process machining (Frazier, 2014)."

Jan 1, 2018

"Conveyed coal flows have been diverted on the basis of real time ash analysis since the 1980s. Many coarse particle separation methods are available through screens, jigs, heavy media separation, particle sorters, to name a few, however bulk diversion requires a representative, continuous analysis to ensure diversion decisions can be made with confidence. Sensors also need to be able to provide measurements at useful time increments so that small tonnages can be diverted for maximum selectivity. Particle separation typically requires high capital costs and there are limitations either in throughput tonnage or particle size or both. Few techniques are able to provide robust and representative analysis of conveyed flows in a useful time basis. Prompt Gamma Neutron Activation Analysis provides multi-elemental analysis of conveyed bulk materials and has been proven in the minerals industry since 2003. This paper outlines the success of this technology in minerals applications in iron ore, phosphate rock and most recently in copper-gold ores, including its use in bulk diversion.INTRODUCTION Naturally occurring quality variability, or heterogeneity, in mineral deposits enables separation and recovery of the valuable components through mining and processing operations. There are distinct advantages in processing the minimum quantity of material to achieve the highest possible yield. Unfortunately, declining ore grades has resulted in larger scale operations and a subsequent loss in selectivity for mining operations. As limits are approached on the practical size of equipment, there is more motivation to investigate alternative solutions. Mining companies are subject to increasing social resistance to growing waste disposal requirements in addition to higher energy and transport costs. Major savings are available by reducing the quantities of material processed where pre-concentration can be effectively applied at early stages in the process. One of the simplest ways to pre-concentrate is to measure the bulk material and reject waste soon after mining so that minimal expense is incurred and that only higher quality material is sent to processing operations. This bulk sorting can occur within the mining operations and has major benefits through energy and other consumables savings. This paper discusses the application of real time analysis technologies suitable for bulk sorting within the minerals industry. Technology that has proven representative for conveyed material bulk analysis and its successful applications to date is explained. Analysis using a sensing technique is only one component of a successful bulk sorting process; the importance of effective diversion systems and a bulk sorting strategy are also discussed. The bulk sorting stage may be one component of a system that could include additional downstream technologies such as particle based sorting systems on a diverted stream."

Jan 1, 2018

By E. G. Ozhogina, O. B. Kotova

"The ores of black, non-ferrous, rare, noble metals are mostly distinguished by a variety of mineral types and complexity of their material composition.The article is devoted to the promotion of the concept of mineral processing in modern realitiesof the deficit of high-quality ores and increase their demand.Normative and methodical documentationsfor specific types of analysis with the definition of the field of application are shown. For example,the pyrochlore-monazite-goethite ores from one of the deposits from Eastern Siberia - Chuktukonskoe ore fieldare tested. The development of mineralogical methods, and testing of specific raw materials are shown.The method of small-angle X-ray (and also synchrotron) scattering, which was developed for solving problems associated with structural high-resolution diagnostics, was tested for bauxites of Vezhay-Vorykvinskoye field. KEYWORDS Technological mineralogy, rebellious ores, ore quality assessment, ?mineralogical-analytical methods INTRODUCTION A highly intense production of many types of mineral raw results in gradual depletion and deterioration of mining-geological and mining-technical conditions of development. Relatively easily accessible and rich deposits are getting exhausted in the first place, and it is necessary to involve poor and rebellious ores into production and processing. Traditional technologies can hardly be applied (Chanturia, 2017; Bazin et al., 2014; Ponaryadov, 2017). The urgency of development of the concept of technological mineralogy focuses on the confirmation of new methods and approaches to the development of mineral raw, creation of scientific and methodological prerequisites for solving the problem of rational development of mineral raw, maximal extraction and integrated application of all minerals (both principal and associated), expansion and strengthening of mineral and raw base. The article is aimed at updating tasks that should be addressed within the applied mineralogical researches: – the forecast of quality of ore at early stages of exploration and technological indicators for the redistribution of raw, – interactive monitoring of these indicators by mineralogical and analytical methods; – assessment of environmental consequences of mining and processing of minerals and measures that eliminate these consequences."

Jan 1, 2018

By N. O. Lotter

The connection between mineralogy and metallurgical performance in a plant was recognised long ago (Gaudin, 1939; Petruk, 1976; Petruk and Hughson, 1977; Cabri, 1981; Petruk and Schnaar, 1981; Kinloch, 1982; Peyerl, 1983, Baum et al 1989 for example). The modern toolbox that we now routinely use for flowsheet development took decades to develop (Lotter et al., 2002; Baum and Lotter, 2004; Lotter, 2011 for example). Many workers contributed considerable time and effort to this overall mission of connecting sampling, mineralogy and mineral processing to integrate the flowsheet development activities. Certain key milestones marked this journey, such as Gy’s treatise on the sampling of particulate materials in 1979, which was later added to by François-Bongarçon, Pitard, Minnitt, and Holmes for example. The development of QEM*SEM by Gottlieb et al. of the MLA by Gu et al. constituted a huge leap forward in accuracy and mineral measurement capacity, as well as a reduction in standard errors of mineral characterisation. The advancement of the microprobe to an automated platform made a significant difference to detailed compositional mineralogy. This led to a strong position from which to draw meaningful processing implications from the mineralogical data. Reproducible flotation testing and reliable plant survey material for characterisation was dealt with by, amongst others, High Confidence Flotation Testing ( Lotter, 1995: Runge, 2010, and Bradshaw, 1997); and Statistical Benchmark Surveying (Lotter, 2005), with earlier prototypes which were steadily improved (Lotter, 1994; Restarick, 1976). The sterling work of Napier-Munn in engaging sound statistical methods with mineral processing led to the successful design and use of methods that could identify and quantify small recovery gains in plant scale trials. This history and present capability are reviewed, including leverage into asset management.

Jan 1, 2018

By F. Bélanger, P. A. Fournier

"Modelling and optimization techniques used in the operation of the Detour Lake Mine leach circuit are contrasted to a 1973 review of contemporary techniques used by a major gold producer. The leach circuit at the Detour Lake Mine was modelled using a full factorial Design of Experiment of stirred tank reactor leach tests using circuit feed. Contour plots of extraction were applied in the plant to optimize addition rates of cyanide and the newly-commissioned lead nitrate system. Contour plot sections were used to understand the impact of sulphur in circuit feed at different operating dissolved oxygen concentrations. The 1973 review paper offers insight into industrially-applied modelling and optimization techniques. In particular, a mathematical model of plant data was developed using multilinear stepwise regression analysis. The model was presented using graphical representations available at the time and applied to optimize the rates of cyanide addition. Off-the-shelf software solutions of today allow mineral processors to quickly and easily visualize data, allowing them to re-allocate time and resources spent processing data to generating raw data and extracting actionable information.IntroductionModelling and optimization in mineral processing is the art of reducing reality through judicious use of assumptions to understand a process and leverage this knowledge to engineer practical solutions to metallurgical problems. Data analysis is at the core of this enterprise.While this paper showcases the modelling work done at the Detour Lake Mine (DLM), the primary objective is to pause and reflect on how far the field has progressed since the 1970’s. A snapshot of state-of-the-art gold cyanidation modelling at that time is a review paper of the Anglo American Group’s capabilities (Brittan & van Vuuren, 1973). The objective of this paper is not a play-by-play of the evolution of modelling and optimization since that time. Rather, it is a comparison of the field at two points in time.In 2016, DLM undertook an extensive bench-scale leach circuit modelling program to better understand the impact of cyanide, dissolved oxygen, lead nitrate, grind size, density, and pH on gold cyanidation (Fournier, 2016). Two major capital expenditure projects were anticipated for 2017: improvements to oxygen control and a lead nitrate distribution system. While the lead nitrate system was planned for construction, the design parameters had not yet been selected. Following the development of the model, plant trials were executed to validate aspects of the model and the methodology was expanded to address other plant issues, in particular the effect of talc chlorite and pyrrhotite in leach feed.The variables of the bench-scale study are summarized in Table 1. Dependent variables were varied using a full factorial design of experiment with two repetitions for each test condition, yielding a total of 300 tests. Test order was randomized to eliminate bias from independent variables."

Jan 1, 2018

By A. Yaghini, Y. Pourrahimian

"Human factors (HFs) play an important role in the mining and mineral industry, affecting operational and maintenance efficiency and safety. Despite the introduction of new technologies and automation in this sector, it is well known that a significantly large proportion of total human errors occur during the operation and maintenance phase. A comprehensive literature review of HFs across several industries is provided. From this review, the impact of HFs on operation and maintenance is summarized, with a focus on what the mining industry is currently doing and what opportunities exist for additional improvements. Future research directions and themes are also identified.RÉSUMÉ Les facteurs humains (FH) jouent un rôle important dans l’industrie des mines et des minéraux, en ce qu’ils affectent l’efficacité et la sécurité de l’exploitation et de l’entretien. Malgré l’apparition de nouvelles technologies et de l’automatisation dans ce secteur, il est bien connu qu’une grande partie des erreurs humaines (EH) se produisent durant une phase d’exploitation et d’entretien. Cet article propose une analyse documentaire approfondie des FH dans plusieurs secteurs. L’impact des FH sur l’exploitation et l’entretien est résumé à partir de cette analyse, une attention particulière étant accordée à l’évolution de l’industrie minière et aux possibilités d’améliorer davantage ses activités. Sont également identifiés les futurs thèmes et voies de recherche.INTRODUCTIONDuring the past several decades, the mining industry has focused on improving equipment, machinery, and methods that have led to more advanced hardware and software, equipment with higher reliability and productivity, and other technological advancements. These actions have improved safety and productivity and have reduced casualties and maintenance workload. Although today’s mining equipment and machinery are technologically advanced and highly reliable, the risk of accidents is still relatively high and key performance indicators have not improved significantly compared to other industries (Sorensen, 2012). A prominent reason could be due to insignificant integration of human factors (HFs) as part of planning, operation, and maintenance activities. The current mining system is a people system, and inevitably HFs and human error (HE) figure prominently in all aspects of this industry. Even the most advanced technologies and innovations require operators and maintainers with significant knowledge and skill, which could increase the potential for HE."

Jan 1, 2018

By I. N. Gridasov, T. V. Ignatova, E. V. Shelepov

"Mikhailovskoye Deposit is comprised of oxidized ferruginous quartzites among other minerals with the former widely spread across the ore field and mined along with unoxidized ferruginous quartzites. PJSC Mikhailovsky GOK strategic development is aimed at iron ore product output expansion. The most critical item of the strategic development road map is process design for separation and concentration of hematite contained in oxidized ferruginous quartzites mined as the by-product in the open pit. Laboratory and semi-industrial tests run to design cost-effective, reliable and environmentally friendly process for Mikhailovskoye deposit oxide quartzites processing included the following processes: - pilot tests of reverse anionic flotation which produced concentrate with Fe60.1-62.9% total iron content and 66-69%Fe recovery rate; - combined magnetic separation and flotation (Marubeni Company, 1982) including slime removal, reverse anionic and cationic flotation and high gradient magnetic separation resulting in 48.9% yield, Fe55-57.5%, up to Fe60.5% hematite concentration ( Fe64.1% being the best result achieved),76.2% recovery. - magnetic separation and flotation, including separation in low gradient (1400 Oe) and high gradient (up to 17000-18000 Oe) magnetic field. The results of these pilots tests were the following: 57-59%Fe concentrate, 70%Fe recovery (Mekhanobrchermet, MGOK, 1982-1988): - magnetic roasting in pilot plant of TSGOK (Krivoy Rog) which produced 61.1%Fe concentrate with 81.5% recovery. Major disadvantage of the method is high generation of dust equal to 20% of the initial feed. Based on third-party studies flotation of oxidized ferruginous quartzites process embracing best processing methods was designed by Metalloinvest Management Company LLC and PJSC Mikhailovsky GOK engineers. This paper discusses analysis of studies aimed at intensification of separation processes with application of mechanical slurry agitation (MSA), addition of alkali (NaOH) and elutriation of initial feed. The paper also provides a design solution to implement a lab-scale MSA plant. It includes feasibility evaluation of MSA inclusion in flotation of oxidized ferruginous quartzites process to enable higher yield and hematite recovery in resultant concentrate. Outcomes of the discussed work have significant value for prospective engineering of OFQ concentration process."

Jan 1, 2018

By R. A. Kleiv, H. Havskjold, N. Church, T. Malvik, M. Tro, E. Larsen

Liberation is one of the major purposes of comminution in mineral processing. In the simplest form, two or more minerals are present in a particle and have to be reduced such that the individual particles contain only one mineral. The complexity of the mineral intergrowth varies from ore to ore. Poor magnetic separation of iron ore may have many causes. In this paper, the emphasis is given to the problem of fine magnetite inclusions in quartz or other gangue minerals. This is highlighted by two Norwegian cases: one on a magnetite ore and the other on a hematite/magnetite ore. The inclusions in question are so small that they are not liberated by reasonable grinding. In both cases, the result has been either poor recovery or lower grade concentrates than desired. The first example concerns production of direct reduction concentrates from magnetite. Magnetic inclusions in gangue particles will be magnetized enough for the particles to pass into the concentrate. The second example is given a more detailed study, where the problem is caused by silicates with small inclusions of magnetite in a combined LIMS and WHIMS separation. This study included microscopy, Davies tube testing, and magnetization measurements. In particular, large gangue particles with magnetite inclusions were shown to have a tendency to bypass the LIMS separators as drag forces in presence of hematite are large. Such particles will then be picked up by the WHIMS as their magnetization is higher than for hematite. This was demonstrated by Davies tube tests, which indicated that such particles were picked up in preference to hematite particles. However, the Davies results did not give a good quantification. Magnetization measurements of gangue particles with magnetite inclusions was shown to be a better tool to quantify the magnitude of the effect of magnetite inclusions in magnetic separation.

Jan 1, 2018

By A. L. Ling, A. K. Janzen

"Design of effective mine water treatment plants depends on the ability to reliably predict treatment outcomes, but systems with multiple chemical and physical treatment processes and recycle loops can be difficult to model. GoldPHREEQC is a modeling framework that integrates mass and flow routing capabilities of GoldSim software and water quality calculations provided by PHREEQC, and is well-suited to modeling parameters of interest in the mining industry, especially metals and sulfate. Physical processes such as membrane separation and greensand filtration are modeled by defining mass rejections for each parameter and flow routing based on vendor projections and bench- or pilot-scale equipment testing. GoldPHREEQC models chemical precipitation processes such as HDS metals removal and gypsum precipitation by (1) performing surface-aging and solubility calculations in PHREEQC and (2) using the GoldSim framework to direct supernatant and precipitate to subsequent process steps. Users can apply this modeling framework to predict effluent water quality, chemical requirements, sludge production, and required equipment capacity to support design, troubleshooting, and cost estimating. INTRODUCTION Design of effective mine water treatment plants depends on the ability to reliably predict treatment outcomes, but systems with multiple chemical and physical treatment processes and recycle loops can be difficult to model. GoldPHREEQC is a modeling framework that integrates mass and flow routing capabilities of GoldSim software (1) and water quality calculations provided by PHREEQC (2), and is well-suited to modeling treatment of parameters of interest in the mining industry, especially metals and sulfate. GoldPHREEQC can also be applied to other water treatment scenarios using inorganic reactions and processes. The GoldPHREEQC model framework moves water and mass between specified model nodes and calculates specified reaction and water quality outcomes. It can be organized to provide flow, load, and concentration information for each location, including effluent and byproduct streams, and outputs can be adapted to include power and chemical costs."

Jan 1, 2018

By T. Avilez, D. Salari

"The economics of developing gold deposits containing elevated levels of cyanide soluble base metals is often challenged by high cyanide consumption and increased operating costs. SART is a chemical process that enables cyanide consumed by base metals to be recovered and recycled for gold leaching. The process also provides concurrent recovery of the base metal to generate incremental revenue from the sale of high-grade base metal sulphide concentrates. Although SART was developed and successfully piloted by Lakefield Research and Teck Corporation in the late 90’s and is now a public domain technology, the adoption of SART has been relatively slow due to concerns about implementation costs and the reliability of metallurgical performance. Through extensive experience in selective metal sulphide precipitation applied to mining wastewater since 2007, BQE Water has provided process know-how, design along with operations and maintenance experience to a number of projects involving the integration of SART into various metallurgical flowsheets on an industrial scale. This paper presents the commissioning experience and operating data from a SART plant treating up to 500 m3/hr of leach solution at a heap leach operation in Mexico. INTRODUCTION One of the current trends in the gold industry globally is the increasing importance of complex polymetallic gold deposits as discoveries of large Carlin type gold deposits become increasingly rare (Sceresini, 2005). The presence of cyanide soluble copper and zinc in complex gold deposits necessitates changes to the traditional gold extraction metallurgical flowsheet. A tool available to the industry to help manage the interference of cyanide-soluble base metals in gold extraction is the SART (sulphidization-acidification-recycling-thickening) process. SART breaks the weak acid dissociable (WAD) base metal-cyanide complexes, precipitates the metals as high-grade sulphide concentrates and makes the freed cyanide available for recycle."

Jan 1, 2018

By Guy Reed, Russell Frith

"The method of determining coal pillar strength equations from databases of stable and failed case histories is more than 50 years old and has been applied in different countries by different researchers in a range of mining situations. While common wisdom sensibly limits the use of the resultant pillar strength equations and methods to design scenarios that are consistent with the founding database, there are a number of examples where failures have occurred as a direct result of applying empirical design methods to coal pillar design problems that are inconsistent with the founding database.This paper explores the reasons why empirically derived coal pillar strength equations tend to be problem-specific and should be considered as providing no more than a pillar strength “index.” These include the non-consideration of overburden horizontal stress within the mine stability problem, an inadequate definition of super-critical overburden behaviour as it applies to standing coal pillars, and the non-consideration of overburden displacement and coal pillar strain limits. All of which combine to potentially complicate and confuse the back-analysis of coal pillar strength from failed cases.A modified coal pillar design representation and model are presented based on coal pillars acting to reinforce a horizontally stressed overburden, rather than suspend an otherwise unstable self-loaded overburden or section, the latter having been at the core of historical empirical studies into coal pillar strength and stability.INTRODUCTIONThe inspiration for this paper is founded in three statements from two eminent persons in the field of coal pillar strength research, Jim Galvin and Essie Esterhuizen, as follows:Both Salamon and Munro and [the University of New South Wales] based the derivation of their pillar strength formulae on a criteria that the diameter of a panel of pillars, W, had to at least equal the depth of mining, H. This was thought to result in full tributary loading. It is now known that there are some mining environments included in both the South African and Australian databases in which mining span must exceed depth by a considerable margin in order to achieve full deadweight loading. Hence, it is logical to conclude that these data points may have contributed to pillar strength being overestimated by Salamon and Munro and UNSW (underline added by authors). Normally, this should be of no consequence because it is reflected in the probability of design success associated with any given safety factor (Galvin, 2006)."

Jan 1, 2018

By T. P. Weldum, W. Conger

"These studies address the relationship between mill media sizing and its grinding efficiency. Starting with the results from a review of the literature, the issues of initial media sizing for a new ball milling circuit, and then optimal media sizing for an existing milling operation, were studied. The Functional Performance parameters “Mill Grinding Efficiency” and cumulative “Mill Grinding Rates” from both plant and test-scale equipment were used, and provide valuable new insight into this topic. A plant media sizing diagnostic tool is presented, as are newly developed testing equipment and evaluation methods, and recent case studies. REVIEW OF MEDIA SIZING LITERATURE For a plant metallurgist to answer the question “How can I maximize plant profit by manipulating this grinding circuit variable?” she must know what effect the variable has on grinding circuit efficiency. Despite the significant cost of grinding media and its potential effect on production capacity, the ‘best’ media sizing remains ill-defined for any given ball mill circuit in the industry today. The underlying reasons for this will be discussed. But the importance of this issue drove Metcom and its industrial partners to take on the challenge of how to engineer the ball charge for an existing grinding circuit. In the absence of any proven method, the first step was a review of the literature. Sponsored by Cleveland-Cliffs, Inc., a broad review of the literature was undertaken, producing “The Effect of Media Sizing on Ball Milling Efficiency” (McIvor, 1997). Among hundreds of publications that were reviewed that discuss the topics of media sizing or wear, forty-five were studied in detail. These were grouped into: plant experiences; laboratory and pilot plant investigations; media wear studies; population balance modeling studies; and general papers on ball milling which included the topic of media sizing. The reader is encouraged to refer to that review. The findings remain unchanged, although some relevant papers have been written since (e.g. Staples et al, 1997; Banasi et al, 1999; Orford et al, 2006; LaMarsh, 2015). The main findings of the review were as follows."

Jan 1, 2018

By E. Guerrini, M. Maccagni, J. Nielsen

"The solution for the treatment of the EAFD has not yet been fully achieved. Some of this dust has still not found an appropriate final destination. Large consortium treatment plants are quite expensive both in terms of investment and operating cost. Meanwhile, the tolling expenses for steel production companies are becoming very important, causing them to look for alternatives. Some steel plants are looking to close their production loop by internal treatment of their dust. Some years ago, Engitec began studying the coupling of the EZINEX® Process, an ammonium chloride electrolysis to recover the zinc contained in the EAFD, with the INDUTEC® Process, a pyro process based on an induction furnace that can convert EAFD into a C.Z.O. similar to the Waelz oxide. The combination of these two processes provides an alternative to the existing treatment options and is particularly interesting for relatively small capacities. In this paper, we would like to give the latest update about these two processes and their possible integration INTRODUCTION Zinc is contained in numerous wastes and secondary raw materials that can be thought of as high zinc concentrate mines. This is a very interesting source of Zn that is typically easily exploitable. Unfortunately, only a portion of these materials are currently processed to recover the metal value, while stabilized or unstabilized landfilling is often the final destination. Pyrometallurgical processes are mainly used to convert the zinc into crude zinc oxide (CZO). The various processes are very similar and characterized by the fact that the zinc bearing materials are usually submitted to a thermal treatment [1] in which the zinc is reduced, vaporized and re-oxidized producing CZO. This material not only contains zinc oxide, but also relatively high concentrations of heavy metals. Many potential CZO sources, such as electric arc furnace dust (EAF), galvanizing ashes, brass foundry and converters fumes also contain chlorides, fluorides and alkali metals that will transfer to the CZO. The classic example is the Waelz oxide [2]. This CZO is an intermediate product that must be transformed into zinc salts or zinc metal. Until now, the conversion to zinc metal is done through two main processes: the sulphate leaching and electrowinning system and the Imperial Smelting Process (ISP). ISP is facing a crisis for technical and economic reasons that has led to the closing of most of the existing plants. In any case, before being fed to one of these two processes, the CZO must be treated to eliminate or reduce some of the contained impurities. In particular, the halides are most harmful to these processes."

Jan 1, 2018

By T. Holmes, S. Davison

"A surge bin at Agrium’s Vanscoy potash operations has been plagued with flow, wear, and corrosion issues since being built in 1967. The culprits? The bin’s carbon-steel construction, geometry, and the resultant funnel-flow pattern are the root causes. An investigation and cost analysis indicated that hopper redesign and retrofit would increase production and reduce maintenance and capital costs. The retrofitted bin provides safer, more reliable operation and has a much longer predicted working life. Using this example, the authors describe bulk-solids-flow theory and highlight the importance of customizing bulk-material-handling-system design using appropriate flow properties to improve reliability, safety, and cost effectiveness.RÉSUMÉ Depuis sa construction en 1967, un réservoir intermédiaire de l’exploitation de potasse Vanscoy d’Agrium connaît des problèmes de débit, d’usure et de corrosion. Les responsables ? La construction en acier ordinaire du réservoir, sa géométrie et la structure de débit en résultant au niveau de la carotte en sont les causes fondamentales. Une étude et une analyse des coûts indiquaient que la restructuration et la rénovation de la trémie permettraient d’augmenter la production et de réduire les coûts d’entretien et en capital. Un réservoir rénové permet de renforcer la sécurité ainsi que la fiabilité de l’exploitation, et sa durée d’activité prévue en est augmentée. En se fondant sur cet exemple, les auteurs de l’article décrivent la théorie du débit de matières solides en vrac et insistent sur l’importance de personnaliser la conception du système de manutention des matériaux en vrac à l’aide de propriétés rhéologiques adaptées afin d’améliorer la fiabilité, la sûreté et la rentabilité.INTRODUCTIONIn early 2013, Agrium’s Vanscoy Potash Operations (VPO) engaged Jenike & Johanson Ltd. (J&J) to provide testing, consulting, and structural engineering services related to proposed modifications to the 270 t special standard product surge bin, which Agrium planned to undertake during a two-week shutdown in August 2013. The bin, which had been plagued with flow, wear, and corrosion issues for its entire working life, was essential for the continuous operation of two of VPO’s compaction plants and for efficient dispatching to loadout. The bin often experienced product hang-ups, clumping on the walls, and plugging at the hopper outlet. Two recent unscheduled mill shutdowns had been partially attributed to flow issues in the bin due to clumping and product plugging up at the screws. These problems increased maintenance costs, limited production capacity, and degraded product quality. Holes and paper-thin sections in the bin walls discovered during a 2013 inspection revealed the potential for major hot material leaks or even structural failure. Either issue would stop plant operations until the bin could be repaired or bypassed. Clearly, the bin cone had reached the end of its life and required replacement."

Jan 1, 2018

By S. Espley, T. Nyabeze, D. Beneteau

"Many mentorship programs are available to Canadian mining industry employees. Some are company-led initiatives, whereas others are provided through educational institutions or nonprofit organizations. In 2016, a national survey was launched to gain insight into perceptions of what mentorship is, learn about available programs, and collate experiences with formal and informal mentorship opportunities. This paper outlines survey findings and delivers recommendations to industry for consideration in employee mentorship programs. In addition, mining industry leaders share their mentor/mentee perspectives. The intent of this paper is to bring awareness of best practices that can help employees grow and develop in their profession.RÉSUMÉ Les employés de l’industrie minière canadienne ont accès à de nombreux programmes d’encadrement. Certains sont des initiatives menées par les sociétés, d’autres sont proposées par le biais d’établissements d’enseignement ou d’organismes à but non lucratif. En 2016, une enquête à l’échelle nationale a été lancée en vue d’obtenir des informations quant à la perception de ce qu’est réellement l’encadrement, de découvrir les programmes proposés et de comparer les expériences aux possibilités d’encadrement, officielles ou non. Cet article présente les résultats de cette enquête et fournit des recommandations à l’intention de l’industrie afin qu’elle les prenne en compte dans ses programmes d’encadrement des employés. En outre, des chefs de file de l’industrie minière partagent leurs points de vue conseillers/protégés. L’intention de cet article est de sensibiliser les employés aux meilleures pratiques, ce qui les aidera à évoluer et à se développer dans leur profession. INTRODUCTIONThis paper about mentorship in the mining industry is based on voluntary responses to a cold survey, written and circulated by the authors. In 2016, a link to an online mentorship survey was circulated to males and females in the mining industry with the belief that mentorship programs should be available to everyone. The link was delivered via the authors’ personal networks in mining, the CIM Reporter, Women in Mining (WIM) email blasts, LinkedIn, and Facebook. This paper summarizes the answers to the survey questions. The paper is a follow up to one by the same authors (Nyabeze, Espley, & Beneteau, 2010), which was written to gain insight into why women join and stay in the mining industry, and to learn why the overall representation of women is low."

Jan 1, 2018

By R. Holmestad, M. Gazizov, S. Wenner, R. Kaibyshev, J. K. Sunde

"Mechanical properties and microstructure of an Al-4.7Cu-0.74Mg-0.51Si-0.48Mn-0.10Cr-0.09Ti-0.02Fe (wt. %) alloy subjected to various thermomechanical processing (TMP) have been investigated and compared to conventional ageing at 170°C (designated T6). Three TMP routes involving cold deformation of solution treated samples were tested. These were (i) 3%-stretching (T8-3%), (ii) equal-channel angular pressing (ECAP) to true strain (e) of ~1 (T8-1) and (iii) ECAP to e~2 (T8-2), all with subsequent ageing at 170°C for 0-96 h. At peak age conditions, both yield stress, ultimate tensile strength and elongation-to-fracture decreased for the T8-3% state as compared to the T6 condition. Intermediate ECAP (T8-1 and T8-2) lead to significant increase in maximum yield stress, ultimate tensile strength and elongation-to-fracture. The changes in mechanical properties were related to microstructure evolution, encompassing changes in grain sizes, dislocation densities, precipitate morphology and phase fractions, which were characterised using transmission electron microscopy. Relations between TMP, precipitation behavior and contributions to different strengthening mechanisms are evaluated.INTRODUCTION Al-Cu-Mg-Si alloys are widely used as structural materials in aerospace industry due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance. These properties are largely due to the formation of a large number of nano-sized metastable precipitates during artificial ageing (Polmear, 2006; Eskin, 2003; Gazizov, Dubina, Zhemchuzhnikova, & Kaibyshev, 2015). The precipitation behaviour in these alloys is complicated and depends among other things on Cu concentration and the Mg:Si ratio (Wolverton, 2001; Chakrabarti, & Laughlin, 2004). In general, the precipitation sequence has been presented in a prior study (Eskin, 2003) as follows:"

Jan 1, 2018

"HPGRs operate in a wide array of applications in mining and minerals. These range from relatively coarse crushing of copper and gold ores at one end of the spectrum to the processing of fine iron ore pellet feed and fine industrial mineral products at the other. Traditionally these circuits involve the treatment of relatively moist materials in pre-grinding circuits; using single stage HPGRs in open circuit or as a closed circuit operation with screening or partial product recycle. More recently, HPGR is increasingly deployed in dry grinding in combination with air classification. The high throughput demonstrated by larger HPGRs has stretched the application towards coarser size reduction duties for a number of new projects. At the same time, the basic principle of inter-particle crushing for generating a product with a high fines proportion gives ground to investigate applying the technology further towards finished product duties. The advantages that HPGR brings are clear. Multi Stage grinding enables energy efficient size reduction across more of the comminution circuit. Primary HPGR serves for a coarse grinding duty, whereas a secondary HPGR is geared towards generating a fine product for downstream processing or even a finished product. This publication summarizes some of the features of staged HPGR circuits and discusses some examples of operating and projected applications.INTRODUCTION In most HPGR applications, the grinding units are used as a single process stage, either in open circuit, such as for pebble crushing [Rose 2002, Westermeyer 2000, Van der Meer 2015] or in closed circuit with classification [Van der Meer 2009, 2012] or product recycling [Van der Meer 2010]. Where a higher plant capacity is required, the HPGRs are commonly installed in multiple lines in a parallel arrangement [Parker 2005, Koski 201, Vanderbeek 2006]. HPGRs can take a wide range of feed size distributions, and grind this down to a product with a high fines content. In general view, there is a limit on the size reduction range that even an HPGR can provide. Grinding down from a very coarse ore (e.g. 70-100 mm) to a very fine product (e.g. 100 microns range) is stretching the ability of a single stage HPGR circuit. Fine grinding generally requires a classification stage that returns the classifier oversize to the head of the HPGR circuit. From one point of view, it can be demonstrated that when recycling a large proportion of fines and middlings back to the HPGR feed results in an effective feed with an overrepresentation of middlings and fines, which will eventually reduce the grinding efficiency and consequently result in an increased recirculation mass flow [Van der Meer 2014]. From another point of view the large recycling mass puts a strain or even a limit on the capacity of present-day conveyor capacity."

Jan 1, 2018

By T. Moloane, C. Bergman, Heloise Thiele

"A pilot test campaign was undertaken to evaluate dense medium cyclone separation efficiencies on samples of iron ore fines (-1mm +300µm). Evaluations were done using both gas and water atomised FeSi types across a range of operating conditions in the presence of slimes build-up. A Mineral Liberation Analyser (MLA) was used to measure size, density, shape and liberation data of DMS feed and products. The results of the test work were used to obtain parameters for modelling of the partition size/density response. The findings indicated that accurate density characterisation of the feed ore is essential in understanding product quality and recovery, particularly due to the effect of porosity and micro-inclusions. A significant off-set between cyclone underflow density and separation cut-point (D50) was found indicating that relatively low feed media densities (about 3.4g/cm3) are required to achieve high density cutpoints of over 4.0g/cm3. In agreement with CFD modelling, the separation quality is dominated by viscous effects, hence FeSi type and slimes content will need to be carefully controlled to ensure efficient separation.INTRODUCTION In the South African context, future resources of hematite are expected to be both of lower head grade and will contain a higher content of banded iron formation (BIF) (1). These ores may require finer crushing in order to liberate the high-grade fractions and will thus increase the amount of -1mm material to be processed. In order to efficiently upgrade these materials, it becomes necessary to re-examine both traditional and novel processes to treat material finer than 1mm in size. These include spiral and up-current classifiers, wet high intensity magnetic separation processes, Reflux classification and potentially includes dense medium separation (DMS). This study presents a technical evaluation of fines DMS using a mineralogically-based particle tracking analysis method (PTA) to calculate efficiencies of separation."

Jan 1, 2018