Search Documents

By S. Heukelman

Zinc or, a zinc refinery in South Africa, uses oxygen enrichment of up to 26% O2 in its fluidizing air to increase concentrate-throughput in its fluidized bed roasters. The aim of the study is to determine whether O2 enrichment can be reduced by introducing micro-pelletized concentrate into the feed blend, while maintaining concentrate throughput rates and calcine quality. A laboratory scale fluidized roaster was used to determine the strength and oxidation kinetics of suitable micro-pellets. The strength of the pellets was determined by the extent of attrition during roasting. It was found that micro-pelletization decreases the fines in the feed to the roasters; the ?500 µm fraction decreased from 87% to 10%. The micro-pelletized particles do break down during roasting, which increases the -500 µm fraction to 31%. The general morphologies of the roasted particles are similar to those found by previous workers. Micro-pelletized concentrate particles require more time than non-pelletized concentrate particles to oxidize in the roasting step, although this is less than the mean residence time of the Zincor roasters. Roasting micro-pellets in O2-enriched fluidizing air increased the reaction rate.

Jan 1, 2011

By Y. Zedan

Cutting fluids play important roles during machining, including the reduction of friction and temperature. Using a cutting fluid, however, degrades the quality of the environment and increases machining costs. The aim of the present research work is to study the effect of cutting fluids and their interactions with cutting parameters on the quality of holes during the drilling of 6061-T6 aluminum alloys. The lubrication types and modes investigated are dry machining, flood lubricant machining and minimum quantity lubrication machining (MQL), while the part quality criteria include the surface finish, the dimensional accuracy, and burr forms and sizes. A scanning electron microscope (SEM) was used to investigate the formation of built-up edges (BUE) in the drill flutes as well as the surface texture of drilled holes. It was found that dry machining and MQL machining can produce parts having quality levels comparable to those obtained in wet machining, when using the optimal cutting conditions.

Jan 1, 2011

By J. -F. Lagueux

Goldex Mine is an underground mine located near the town of Val-d?Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long hole stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23 Mt of ore, large blasts up to 1.8 Mt are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km radius of the mine site. In addition to managing mass blasts, means must also be found to mitigate the vibrations produced by the blast to diminish the disturbance to the neighbourhood. Therefore, the mine used numerous tools to properly plan the blasts and reduce the impacts. A program to control vibrations was one of the first tools put in place. The program?s aim was to draw up an action plan to ensure a follow-up of the homes by inspecting them. The second tool was to develop a methodology to plot a reliable attenuation curve and to adequately determine the maximum charge weight for each blast. Finally, effective communication tools were developed to inform the neighbourhood. There was a huge amount of work to be done in relation to the bench. Reliable and fast loading techniques had to be found to load large blasts in a very short period of time. Adequate logistics had to be developed to send underground more than 20,000 kg of emulsion per day while performing the daily underground operations. Technology had to be developed to adapt the i-kon electronic blasting system to large blasts. Since the control of the charges was the major factor to reduce surface vibrations, it was important to employ loading techniques that would permit decking of the long holes to reduce the charge weight per delays without adversely affecting the loading. All of this work requires an enormous amount of energy but also close collaboration between the different stakeholders (various departments, suppliers and consultants).

Jan 1, 2011

By Kaspar Tall, Dmitri Goljandin, Kristiina Vilsaar, Jaan Kers, Valdek Mikli, Lifeng Zhang, Riho Tarbe, Viktor Laurmaa, Mart Saarna, Priidu Peetsalu

In this paper, the mechanical milling of the Printed Circuit Boards (PCB) was carried out. First goal of the work was to examine the management of the WEEE, in particular the re-use of PCB. Firstly, recycling methods of PCBs were summarized. During the study mechanical separation methods (magnetic-, density- and air separaten), electrical, and chemical methods were examined. Secondly the optimal particle size for air-classification was determined. Several tests were carried out to find the most effective separation method for separation of different material groups from PCB scrap. The new air classification stand was developed for testing the separation of lightweight particles like tinfoil stripes and plastics. The test results showed sufficiently good separation of heavier Al and Cu. For milled materials characterization the SA, IA, laser diffraction analysis and SEM were used. The chemical composition of the PCB powders was studied by means of energy dispersive X-ray microanalysis (EDS).

Jan 1, 2011

By G. Kugler, M. Tercelj

"The 1.2690 high alloyed tool steel is usually applied for cold working and is alloyed with carbide-forming elements Cr, V, W and Mo. It exhibits very poor hot deformability. Since there is no enough available data in literature for elucidation of this problem, hot workability and development of microstructure during hot deformation was studied. Hot compression tests were carried out in temperature range 850-1150 °C and strain rates range 0.001-6 s-1. SEM and OM were used for observation of microstructure. Results revealed very complex precipitation of carbides that depends on deformation temperature as well as on strain rate. It was found that especially at lower temperatures of hot working range the precipitation of carbides strongly depends on strain rate. Three different hot deformation behaviors’ were observed depending on temperature and strain rate range.IntroductionThe hot workability of highly alloyed high speed steels is usually described as relatively poor in comparison to other steels due to their tendency of cracking during hot working especially when inappropriate hot working conditions are applied. Alloying elements such as Cr, W, Mo and V in ledeburitic tool steels form carbides that improve hardenability, strength, hardness, wear resistance, etc., but they decrease hot workability and narrow hot working temperature range in comparison to conventional steels. The size, distribution, type and fraction of carbides, as well as the thermomechanical history of material and hot working parameters have major influence on the hot workability. The microstructure of ledeburitic tool steels during hot deformation can be characterized as a two-phase system consisting of an austenite matrix and a combination of ledeburitic carbides [1-4]. In the soft-annealed condition the total volume fraction of carbides is in the range 19-30% and in the quenched condition in the range 9-25%, depending on the chemical composition. During heating before deformation a large quantity of carbides dissolve, but non-dissolved carbides can have an extremely diverse influence on the hot workability due to variations in their composition, size, distribution, hardness and shape, and their different behavior during the deformation phase [5-7]."

Jan 1, 2011

By A. Luckita, A. Samtani, R. Barus, J. R. Donald, J. Syarifuddin

In conventional Rotary Kiln-Electric Furnace (RK-EF) laterite nickel processing, management of dust continues to be problematic. A more efficient processing of dust represents an opportunity for energy efficiency, increased production, and productivity. PT International Nickel Indonesia (PTI), together with Vale Base Metals Technology Development (VBMTD), has successfully developed and implemented a novel flowsheet enhancement that capitalizes on these opportunities. In the novel flowsheet, the dust recycle stream is moved forward in the RK-EF laterite nickel smelting process. The dust is injected into the kiln's main burner, as opposed to being recycled to the dryers. A similar treatment of dust is commonly practiced in the cement industry; however, application to nickel smelters has not been fully developed to date. This paper describes this dust insufflation technology, the process through which it was developed for laterite nickel processing, and summarizes the lessons learned. A key conclusion is that successful new technology development requires a multi-disciplinary team involving members from research and development, study management, engineering consulting firms, project implementation management, process technology and operations.

Jan 1, 2011

By S. A. Bunk, E. C. Eccleston, J. J. Amsden

Fluidized bed technology has been widely applied to mineral and metallurgical processes. Over the years, modeling of fluidization technology has progressed to a level at which basic design parameters can usually be defined based on empirical correlations. In addition, scale-up considerations have become better understood, and significant advances have been made in the area of computer simulation. Despite these advances, fluidization is a complex phenomenon, and modeling tools remain limited in their ability to simultaneously model both fluidization and chemical process parameters. As a result, almost all mineral and metallurgical applications of fluidized bed technology require pilot testing prior commercial scale design. This paper outlines pilot plant testing requirements and process development considerations for development of low technical risk commercial designs.

Jan 1, 2011

By Winton J. Gale

The subsidence over a longwall panel at Tahmoor Mine in the Southern Coalfield of NSW, Australia, was found to be approximately twice the size it had been in previous measurements. An investigation into the potential causes was conducted using computer modeling together with hydrological characterization and detailed geotechnical characterization of the strata. The abnormal subsidence was found to be consistent with localized weathering of joint and bedding planes above a depressed water table adjacent to an incised gorge. The study showed that other factors such as variation in stress field, joint zones, variation in rock strength and topographic factors did have sufficient impact to induce the abnormal subsidence. The results have significant implications to subsidence prediction in areas that may be prone to the phenomenon found at Tahmoor. Key indicators of the potential for this form of abnormal subsidence are presented.

Jan 1, 2011

It is crucial to reestablish a domestic rare earths minerals production industry to help secure the Nation's clean energy future, reduce the U.S. vulnerability to material shortages related to national defense, and to maintain our global technical and economic competitiveness. Given that the Chinese dominance of the rare earths market has adversely impacted supply stability and endangers the United States and its allies' assured access to key materials, rare earths should qualify as materials either strategic or critical to national security. Further, the U.S. government should facilitate the reintroduction of a globally competitive rare earth industry in the U.S. Realization of this objective requires: ? Developing domestic processing capability so that the U.S. is not primarily dependent on China as a source of rare earth ore, and almost exclusively dependent of China for processing of the ores. ? Providing a mechanism where access to Federal lands for rare earth exploration and extraction is possible, and ? Training engineers to design and operate rare earth ore processing facilities

Jan 1, 2011

By J. Brian Anderson

Jointed micropiles were investigated to support bridge foundations where shallow rock was present. In this application, micropiles would have some amount of unsupported length, and would be subject to nominal lateral loads. Five lateral load tests were conducted on micropiles to demonstrate the impact of casing joints and rock socket embedment on lateral behavior. Load tests were simulated with FB-Multipier, a hybrid-finite element program for analysis of deep foundations, for proper design of the loading apparatus and instrumentation. The micropile sections were 2 m (6.56 ft) long, 273 mm (10.75 in) in diameter, 13 mm (0.5 in) thick walled, with a 50-mm (2-in) long threaded joint. Micropiles were made of one to three casing sections and were embedded 0.3, 0.6, 1.5, or 3.0 m (1, 2, 5, or 10 ft) into rock. In each test, two identical micropiles were pulled together using a simple frame until the weaker pile failed. All micropiles were instrumented with inclinometer casings while two contained strain gages at 0.76 m (2.5 ft) intervals. Load and displacement were measured at the pile heads. Tests showed the embedment of 0.6 m, 1.5 m, and 3.0 m (2 ft, 5 ft and 10 ft) sufficiently carried lateral loads over 180 kN (20 tons). The piles embedded 0.3 m (1 ft) were not able to maintain lateral load. In general, all micropiles tested to failure exhibited a brittle failure mode where there is small lateral deflection followed by a sudden failure at the casing joint. This was demonstrated in three of the load tests. In most cases, the micropiles were stiffer and stronger in the load tests than originally predicted numerically. The final test, where piles were not loaded to failure, verified that embedding vibrating wire rebar strain meters in the grout captured the bending moment profile of the micropile. The results showed the maximum moment in this case being carried directly across the threaded joint as predicted by the preliminary models. The results of these tests were used to calibrate the FB-Multipier numerical model. Using a load test that included bending strain measurements for a match, the soil properties were adjusted to produce reasonable matches for all of the load tests.

Jan 1, 2011

By S. M. J. Mirazimi, F. Rashchi

Recovery of vanadium from LD (Linz-Donawits) converter slag was evaluated by means of microbial leaching. Vanadium leaching was performed in two stages. In the first stage, the bacteria were grown in a culture medium and in the second stage; vanadium containing slag was added to the metabolites produced by bacteria. Bioleaching was performed using heterotrophic bacteria Pseudomonas Putída. Control tests without bacteria inoculation were also performed and the results were compared with bioleaching outcomes. Optimal conditions for the bioleaching of vanadium containing slag were determined.

Jan 1, 2011

By Donna Guillen, Matthew Lehar, Sebastian Freund, Jennifer Jackson, Helge Klockow

"Research and development is currently underway to design an Organic Rankine Cycle (ORC) system with the evaporator placed directly in the hot exhaust stream produced by a gas turbine (GT). ORCs can be used to generate electricity from heat that would otherwise be wasted, thus producing carbon-free energy. In conventional ORC configurations, an intermediate oil loop is used to separate the hot gas from the flammable working fluid. The goal of this research effort is to improve cycle efficiency and cost by eliminating the pumps, heat exchangers and all other added cost and complexity of the additional heat transfer loop by developing an evaporator that resides in the waste heat stream. Direct evaporation – although simpler and less expensive to implement than indirect evaporation of the working fluid – has historically been avoided due to a number of technical challenges imposed by the limitations of the working fluid. The high temperature of the hot exhaust gas may cause decomposition of the organic working fluid and safety is a major concern due to the high flammability of some of these working fluids. The research team has addressed these challenges and developed a new direct evaporator design that can reduce the ORC system cost by up to 15%, enabling the rapid adoption of ORCs for waste heat recovery. The ORC system is intended to integrate with the GT either as a retrofit or to be marketed as a single package, thus maintaining the manufacturer’s warranty.IntroductionWaste heat from turbines and engines used in industrial applications along with waste heat from industrial processes are exceptionally abundant sources of energy. If even a fraction of this waste heat could be economically converted to useful electricity, it would have a tangible and very positive impact on the economic health, energy consumption, and carbon emissions in the U.S. manufacturing sector. Land-based gas turbines are used in a broad range of applications to produce both shaft and electrical power. Most commonly known for generating electricity either as peaking units or as base load units, they are also used to directly drive pumps, compressors or other machinery requiring shaft power. Simple cycle gas turbines have the advantage of a short startup time relative to coal-fired and nuclear units, however, they incur a significant penalty on their efficiency. Large frame gas turbines usually are combined with bottoming steam-based Rankine cycles to increase the overall efficiency of the system and thereby improve their cost performance. Small-frame gas turbines with exhaust temperatures around 500°C could in principle benefit from steam bottoming cycles, but rarely use them in practice because of the high capital cost of the steam system. Particularly for base load small frame gas turbines, akin to those used in pipeline applications, an increase in efficiency is highly desirable."

Jan 1, 2011

By Dale Preece, Mike Stern, Steve Piercey, Ayman Tawadrous, GC Zhao

The McArthur River uranium mine in Saskatchewan, Canada is the world’s largest high-grade uranium mine. It has employed a freeze-wall system consisting of multiple freeze pipes to control the large quantities of water encountered during mining.

Jan 1, 2011

By Hongmin Zhu, Guihua Wang, Xiangsheng Wang

"The anode process of carbon electrode in fluoride melt was studied by voltammetry and chronoamperometry. Anode gases were analyzed by gas chromatography on-line during controlled-potential electrolysis. Two peaks were observed on the cyclic voltammograms. According to the results of gas chromatography, the first peak was corresponded to the discharge of residual oxide ions, with the formation of CO and CO2. Discharge of fluoride ions occurred at 4.1 V vs. Li+/Li, and leading to the anode effect. With the occurrence of anode effect, small amount of CF4 was detected. As the potential reached 4.5 V, CF4 and C2F6 gas evolution occurred, and the current increased to form the second peak.1.IntroductionIn the primary production of Aluminum and some rare earth metals like neodymium, a departure from normal cell operation known as anode effect results in the generation of perfluorocarbons (PFCs), which have high global warming potentials [1]. Owing to the pressure of environmental protection, considerable research has been carried out to clarify the mechanism of anode effect and PFC generation of industry and laboratory cells in the aluminum electrolysis system [2-9]. The common result on PFC generation is that the PFCs are emitted from Hall-Heroult cells only when they are on anode effect. In this article, we selected LiF, the main electrolyte for the neodymium electrolysis [10-11], to perform further investigation on the underlying kinetics of PFC generation and the nature of the reactions at the electrode.2. ExperimentalAll experiments were carried out in an alumina tube reactor, which was filled with high purity helium atmosphere. Spectrographic graphite crucibles were used, which played the dual role of molten fluoride container and the counter electrode. Lithium fluoride was analytical grade. The experiments were carried out at 900 °C."

Jan 1, 2011

By A. Rojo, N. J. Ramirez, J. E. Salgado

"This work aims to characterize the plastics used in a handgrip located in the car interior body in order to improve its design process and be able to predict its behavior when the part is subjected to impact test involving human casualties.Through stress analyses at high speeds and a video camera set up (front and side view), the reduction of area of specimen was obtained from image analysis, allowing to get the stress-strain real curve of the material.Continuing the characterization process a set of impact test was developed, where standard lzod configurations were used in unnotched specimens. From these tests were gotten displacement curves and absorption energy estimations.The proposed testing procedure allowed the acquisition of force and displacement data through time at various strain rates which are indispensable for the characterization of dynamic events. Using a specimen with a special configuration has shown a more detailed dynamic behavior resulting into more accurate numerical analyses within the design process.IntroductionIn the design process, one of the many analyses which take place is the impact test of the designed part. Nowadays there are many software capable to do these kind of analysis and each industry use the one they think it is convenient for them, but also the selected software has mathematic models that help to find the solution and the simulation of the case of analysis. These are not the only considerations that a company has to take into account, other one is the type of information and data necessary to feed the software. For this study we are going to focus on the acquisition of these data.The mail reason of this work is that generally the supplier gives the card of the material with all the characteristics and information requested by the buyer, but all of that information is acquired by standard methods, but it is inconvenient when the materials are polymers."

Jan 1, 2011

By L. Mabiza

Keywords: Pyrometallurgy, furnace, sulphur, SO2, off-gas, Zimplats Zimplats embarked on an off-gas sampling campaign in December 2009 to characterise the concentration of SO2 in the off-gas from their 13 MW furnace. In excess of forty isokinetic samples (US EPA Method 8) were taken over seven days. The aim of the sampling campaign was to increase the understanding of factors that influence sulphur release from sulphide concentrates in an electric furnace. Specifically, detailed monitoring was conducted over various operating conditions to evaluate: ? The relationship between SO2 and feed rate (i.e. furnace power) ? The relationship between SO2 and ingress (i.e. furnace freeboard pressure) ? The impact of concentrate bed thickness on SO2 (i.e. blacktop) ? The effect of events such as tapping and converter slag return on SO2 ? The desulphurization reactions that take place in the blacktop A model was developed to predict the SO2 content in furnace off-gas for a particular set of operating conditions. In order to evaluate the impact of random, uncorrelated changes in concentrate composition, ingress and power (feed rate) on the SO2 content of the off-gas, a Monte Carlo approach was adopted whereby concentrate composition, power, and ingress were allowed to vary randomly around selected set-points. The model is primarily based on the release of ?labile? sulphur from the partial thermal dissociation of sulphide minerals with an over-stoichiometric sulphur content (e.g., Fe7S8 decomposition to FeS and S). The main findings of this work suggest that labile sulphur does not fully account for the measured SO2 content of the off-gas, and that limited oxidation of sulphides during melting also contributes to the SO2 content. Details of sulphide oxidation reactions in the furnace remain unclear, and it is currently not possible to provide a theoretical framework for the relationship between the extent of oxidation and variables such as temperature, gas composition, particle size, and residence time in the furnace black top. Through the use of the Monte Carlo model it was, however, possible to constrain the extent of sulphide oxidation to about 1%. This work has shown in practice what was expected in concept, that SO2 in off-gas is proportional to furnace power and ingress rate. The model that was developed consistently slightly under-predicts the quantity of SO2 generated. It also highlights that more work is required to better understand the analytical methods used to analyse for SO2 in off-gas.

Jan 1, 2011

By N. J. Rarmrez, C. Perez, J. D. Calderon, L. Lopez

"Among the thermal characterization of any material, one of the variables to know is the coefficient of thermal conductivity because this value can tell how much heat passes through the material and if the material could be used as an isolator. In order to determine this parameter is required some kind of special equipment and controlled conditions which implies high costs in the development of tests. The present paper proposes a design of a low cost measurement system in order to determine this coefficient with the lower possible error. This equipment was thought for companies or labs where they do not have the economic resources or the infrastructure (environmental controlled labs, heat flux transducers, human resources with specialized knowledge) to do this kind of tests.The system is based on ASTM C 518 - 04 [l] and integrated by two plates (one that contains a thermal resistance and which temperature is controlled by a closed loop controller and the other one with a route of water flow). The thermal resistance is actuated by a relay and a supervisor system checks the total time the relay is on in order to determine the effective power applied to the system. The contact faces of the plates contain a group of temperature sensors connected to a data acquisition system that process and record the temperature in each measurement point.With the power applied to the system, the measurement of temperatures and a process of calibration is possible to determine the coefficient of thermal conductivity. IntroductionWithin the thermal characterization of a material of known variables is the coefficient of heat transfer, since this value can know the amount of heat the material is capable of transferring or isolating. To determine this ratio requires specialized equipment and controlled conditions, which implies high costs in the development of a test. This article proposes a design of a low cost machine to allow closer this coefficient with the least possible error. This equipment was done thinking about companies that do not have the infrastructure (laboratories, controlled environment, heat flux sensors, human resources expertise) and financial resources to conduct these tests."

Jan 1, 2011

By Zoë Mullard

The introduction of Web 2.0 platforms (also referred to as social media), with their architectures of participation, has ushered in a new era of technological interaction and information exchange that is changing the nature of corporate-community communications. Web 2.0 platforms give users the ability to generate data collaboratively, meaning that more stakeholders maintain the expectation of being able to contribute to online dialogue. In light of these changes, it is important for business to consider how social media can be used strategically to enhance stakeholder relationships and increase business efficiencies. This article provides three case studies of how different stakeholders in the mining industry are strategically using Web 2.0 platforms to communicate with target audiences. The case studies are based on the experience of respondents and from website observations, which were undertaken as part of a thesis research project by the first author (Mullard, 2010), focusing on the application of social media in the mining industry.

Jan 1, 2011

By R. Steele

In addition to compliance with government emissions and reporting requirements, mining and mineral processing companies are increasing energy efficiency to reduce costs and become more competitive in the global marketplace. One of the major obstacles to identifying opportunities for increased energy efficiency is the lack of readily available data on energy use, and more importantly the energy use linked to production data, that identify energy reduction opportunities. As well as energy reduction, mining and mineral processing companies often struggle with the prediction of energy use, and are often penalized for under or over forecasting. Once again, it is the lack of timely information that makes this prediction difficult. This paper looks at expanding the use of a Manufacturing Execution Systems by integrating with Energy Solutions. This will provide automatic, timely information, at a granularity that makes it easier to identify energy reduction opportunities, reduce energy costs, and better predict energy use in a mining and mineral processing operation.

Jan 1, 2011

By Onder Guney, Erdem Demirkesenm

"In this study, the crystallization behavior and thermal expansion coefficient of a lithium disilicate (LS2) based glass-ceramic derived from SiO2-Li02-AhO3-K2O-ZrO2 system was investigated by using x-ray diffraction (XRD), high temperature x-ray diffraction (HTXRD), differential thermal analysis (DTA) and dilatometer techniques. Analytical reagent grade chemicals were chosen as raw materials for preparing glass batches. Nucleation and crystal growth heat treatments were planned according to DTA results. The amounts of the amorphous and crystalline phases developed during the heat treatments were determined by quantitative XRD. XRD results of crystallized samples showed simultaneous formation of lithium silicate (LS) and quartz in the early stage of the crystallization followed by formation of lithium disilicate (LS2) at higher temperatures. The thermal expansion coefficients of glassceramics were also measured depending on the applied heat treatments.IntroductionSignificant developments occurred in all ceramic materials provide the fabrication of high quality dental implants [1]. Glass ceramic based dental restorations like dental inlays, crowns, bridges and veneers are becoming increasingly popular with their reliable and durable performance [2,3]. In addition to their advanced functional properties, glass ceramic implants especially lithium disilicate glass ceramics also face the esthetics expectations of patients and dentists and in this way they are starting to take the place of metal based restorations today [1,3,4,5]. Lithium disilicate glass-ceramics derived from multicomponent glass systems have some superior mechanical and optical properties comparable to natural teeth [ 6]. In restorative dentistry, mechanical characteristics of biomaterials play very crucial role in order to resist the masticatory forces occurred during biting and chewing [7] According to three point bending test results of Roland, flexural strength of the lithium disilicate glass-ceramics were 400±40 MPa and their fracture toughness (K1c) are approximately 3,3 MPa m112 [2,6]. In addition to high mechanical strength, aesthetic appearance is another important prerequisite as material for dental restorative applications. Translucency and light transmission of the LS2 glass ceramics mimic enamel. Moreover, opacity of the material can also be adjusted depending on the restoration types [2,6, 7]. These superior properties of the LS2 glass ceramics are directly related with chemical composition of the base glasses and controlled crystallization heat treatments [ 4, 7]. The aim of the present work is to determine the effect of heat treatment schedules on the crystallization behavior and thermal expansion of the LS2 glass-ceramics."

Jan 1, 2011