Search Documents

By M. Pfeifer, M. N. Brodie, D. J. Barratt

"This paper reviews design trends related to the various SAG mill configuration and drive options available today. The impact of these options on capital and operating costs is assessed, and key technical issues reviewed. The discussion is based on the conventional North American ’pancake’ mill configuration. IntroductionDuring the past decade mill technology has evolved significantly in the following key areas:• improvements in variable speed motors continue with on-going advances in electronics;• ring motors, or gearless drives, are becoming more common in mill sizes 32 ft and larger, with ratings of 10 000 HP and greater;• geared drives have become available up to ratings of 9500 HP per pinion, compared to the earlier 6000 HP guideline;• improvements in speed reducer technology due to the use of carburized and ground precision gearing, make the high speed motor-speed reducer drive more competitive with the direct coupled low speed motor drive;• a unique speed reducer drive is being introduced to this industry which combines ring gear drive pinions with speed reduction. mprovement in gear alignment is claimed, and the overall drive arrangement is more compact than is possible with a conventional speed reducer drive;• the first 38 ft and 40 ft diameter mills have been designed and manufactured; and • application of large multi-shoe bearings have made shell supported mill configurations available for all, including the largest sizes. These designs have flat instead of conical mill shell ends, and have the potential for technical and cost advantages compared to conventional trunnion supported designs.This proliferation of mill design features provides several options to those involved in planning and design of milling plants, and requires more extensive evaluation to optimize mill design features to best suit specific project requirements."

Jan 1, 1999

By Emil B. Milosavljevic, Ljiljana Solujic

Cyanide is exceptionally reactive, and in typical gold/silver processing liquors, cyanide may be transformed into various species and forms depending on the mineralogy of the ore and chemical make-up of the process water. The exact speciation and relative concentrations depend on the Eh and pH values, as well as the free CN concentration in the system. Very good cyanide balances can be achieved by the judicious selection of the analytical techniques used. The choices an analyst has to make (which analytical methods to use and which ones to avoid) in order to gain better understanding of cyanide speciation and balances in a particular system under investigation will be discussed. Examples of cyanide balances obtained for the laboratory scale tests (agitated leach and column tests) will be presented and discussed.

Jan 1, 1999

By Iain B. Mackenzie

In 1997, a thin layer of Microtherm Microporous Insulation was used to replace fireclay brick behind the magnesia/chrome working lining in #5 refining furnace at BHP?s San Manuel AZ smelter. A 23°C reduction in shell temperature was obtained, together with a large increase in the working capacity of the vessel. There was no sign of metal penetration as a result of the increased insulation. Following these highly favorable results, BHP have introduced this product into all of their refining furnaces.

Jan 1, 1999

By Hiroyuki. Fukuyama

The pseudo-binary phase diagram of the cuspidine (3CaO2?SiO2?CaF2) - CaF2 system has been studied by electron probe microanalysis (EPMA) and X-ray diffractometry (XRD). To prevent fluorine loss in the form of a HF gas by a reaction of CaF2 with water vapor at elevated temperatures, the equilibrium experiments were conducted with the sample hermetically sealed in a platinum tube. By employing this technique, it was successfully revealed that cuspidine exists as a stable phase and congruently melts at 1684 ± 1 K, and the cuspidine - CaF2 system presents a simple eutectic type of phase diagram, of which eutectic temperature has been estimated to be around 1540 K, corresponding to the composition of 40 mass% 3CaO?2SiO2 - 60 mass% CaF2?

Jan 1, 1999

By E E. Cloete, R I. McCrindle

Permitted explosives were previously nitroglycerine based and cap sensitive. Due to safety, health and environmental requirements, water-containing explosives, such as watergels and emulsions, were used instead. However, in order for these explosives to perform at their designed level during blasting, a more powerful stimulus than is delivered by detonators on their own is required.

Jan 1, 1999

By M. J. Perpich

Electrochemical and chemical leaching tests were carried out on chalcocite, covellite and chalcopyrite in acidified iron sulfate solutions sparged with a mixture of O2 - SO2. The gas mixture catalyzed the ferrous to ferric oxidation reaction in situ and, therefore, increased the redox potential and oxidizing strength of the solution. Anodic polarization curves in dilute sulfuric acid on copper sulfide electrodes showed that chalcopyrite passivates and dissolves at current densities orders of magnitude less than chalcocite and covellite. The addition of a depassivating agent (Ag+) increased the passive current density of chalcopyrite and caused breakdown near 0.625 V (SCE). The depassivating effect was also observed during the leaching of chalcopyrite particulate samples as small amounts of Ag+ added to acidified iron sulfate solutions in the presence of O2 - SO2 mixtures greatly increased the leaching rate and the total amount of Cu oxidized (> 90%). Passivation was prevented in the absence of Ag+ by decreasing the initial oxidizing power of the solution and by pretreating the sample in a reductive leach. Both of these methods resulted in transformation of the chalcopyrite surface from its characteristic greenish-gold into deep black. Increased concentrations of Fe+++ due to 02 - S02 sparging were then able to oxidize the transformation product.

Jan 1, 1999

WMC was a late entrant into Indonesia in mid-1996, but had considerable experience and success in exploring in Asia, particularly the Philippines since 1988. Given the geological similarities to the Philippines and IndonesiaÆs superior æcradle to graveÆ Contract of Work (CoW) tenure system, the entry into Indonesia was a logical decision but nonetheless a result of detailed planning. At the time of WMCÆs entry, Busang in Kalimantan was still a 60 moz wonder and the euphoria of this apparent discovery had overflowed into every aspect of exploration. Many junior mining companies and tenement speculators were clamouring for properties in Kalimantan, whilst other serious and capable explorers had to compete for properties and exploration personnel in an era of high and often unrealistic expectations. The picture in late-1998 and through 1999 is dramatically different, as the worldwide downturn in the price of most metals coincides with financial and social crises throughout most Asian countries. The impact of this has been particularly severe in Indonesia and when coupled with the negative sentiment of the Busang fraud has resulted in an exodus of junior companies and also some of the majors. This is understandable given the much publicised social unrest, uncertainty of government, mooted changes to the eighth generation CoW, increasing illegal mining and heightened community expectations. The reality however is somewhat different and although clearly a crisis in many respects, it is also a time of great opportunity.

Jan 1, 1999

By P. J. Cook

Comminution is one of the fundamentals of mineral processing, requiring large expenditures to be made on capital equipment, installation, power and maintenance. The trend toward lower grades and higher operating costs, mean mining operations are becoming increasingly marginal. The challenge is to improve and more importantly, utilize crushing and milling technologies that provide for reduced capital and operating costs whilst providing increased unit efficiencies. The Svedala Barmac Autogenous Crushing Mill presents such an opportunity by providing many of the cost savings and production increases required by its ability to produce a finer mill feed size and realize reduced energy consumption. This paper briefly describes the operation of the Svedala Barmac Autogenous Crushing Mill and reviews its benefits towards improving the efficiency of crushing and milling operations.

Jan 1, 1999

By William Petruk, J. H. Gilles Laflamme, Jean Robitaille, Louis J. Cabri

"A quantitative mineralogical study using ore microscopy, electron microscopy, proton-microprobe, image analysis, and material balances was done on samples from the circuit of a concentrator in Quebec, with particular emphasis on the Cu concentrate. The ore contains many different minerals, of which the principal ones, in decreasing order of abundance, are pyrite, sphalerite, chalcopyrite, bornite, galena, tennantite, and pyrrhotite. Minor to trace amounts of covellite, chalcocite, stannoidite, mawsonite, colusite, wittichenite, miharaite, hessite, petzite, electrum, and an unidentified Cu-Pb-Bi-sulfide also occur.Liberation of pyrite is very high in all size fractions for all samples (ranging from 80-91 %). Liberation of chalcopyrite, bomite, sphalerite, and tennantite is relatively high, on average, in the head .sample and Cu concentrate (55-78% and 66-88%, respectively). Most of the chalcopyrite in the flotation tails is not liberated, whereas about one half of the tennantite and sphalerite are liberated in both the flotation and :final tails. Recoveries calculated for the Cu concentrate (on the basis of assays, mineralogy, and image analysis) are chalcopyrite 72. 5%, bornite 73. 7%, sphalerite 41.0%, tennantite 70.9 %, and galena (together with some trace minerals) 34.2%. It was also calculated that the Cu concentrate contains 10.0 % of the pyrrhotite and i.4 % of the pyrite.Materials balance calculations were done on the five major sulfide minerals to determine the mineralogical distribution of 13 major, minor, and trace elements (as determined by protonmicroprobe analyses). It was determined that tennantite is the principal carrier of Bi (67%), As (90%), and Te (86%) in the Cu concentrate. Therefore, removal oftennantite, which is mostly liberated in the Cu concentrate would significantly reduce these three contaminant elements, but at a loss of9% of the Cu, 2.0% of the Zn, and 0.7% of the Ag. The precious metals (Au, Ag) occur as discrete minerals (electrum, petzite, hessite). Some of the Ag also occurs in solid solution in bornite (23.1% of Ag in Cu concentrate), tennantite, and sphalerite. Four of the major sulfides (chalcopyrite, bomite, sphalerite, tennantite) in the ore also contain measurable concentrations of the following trace elements: Se, Cd, In, Sn, and Sb, occurring mostly as solid solutions. Some of these elements are also concentrated (up to about 18%) in minor and trace minerals such as colusite, stannoidite, and mawsonite."

Jan 1, 1999

By Fathi Habashi

"On August 3, 1888, German Patent No. 43977 entitled ""A Process for the Production of Aluminum Hydroxide"" was issued*. The discovery which led to the patent was made by the Austrian chemist Karl Josef Bayer (1847-1904) (Fig. 1) who was at that time in Russia, and the process became known as the Bayer Process in his honour(1)(2)- The process imediately achieved industrial success, displacing the pyrometallurgical process that had been used until that time to produce alumina. The Bayer Process involved the pressure leaching of bauxite with NaOH solution to obtain sodium aluminate solution from which aluminum hydroxide was precipitated by seeding. Today bauxite is not only the principal source of aluminum but also of gallium, both metals being effectively recovered by the Bayer Process. The purpose of this paper is to outline the historical background of this discovery and its importance to hydrometallurgy."

Jan 1, 1999

By J. E. Friant

The Mini-DiscTM cutter drill bit is a radical design departure from the traditional tri-cone rockdrill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-DiscTM drill bit, referred to as the “Disc Bit” has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory can not shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By S. A. Davis

In July of 1996, the Kroll process began production again at TIMET's Henderson, NV, manufacturing facility. This, after being shut down for several years due to low market demand for titanium. Faced with limited pond capacity and increasing costs for water and wastewater disposal and storage; process changes were made to recycle water used to wash Kroll titanium sponge back into the sponge leaching process. This idea was revisited from 1992-93, when three consecutive attempts to recycle water for this application were unsuccessful due to early pump failure. Since it was uncertain why previous attempts failed, a complete understanding of the existing system was first sought. This included reviewing piping and flow diagrams; taking field measurements for all the piping, valves, and fittings; analyzing the wastewater composition; and modeling the fluid dynamics and control of the system. The fluid dynamics of the system were modeled by breaking the piping network up into nodes and applying the Bernoulli equation to each segment. The fluid flowrate control valves were modeled for this purpose also and the models were used to help specify the required processing equipment and control ranges and tolerances. Once the project was completed, an operating procedure was prepared for operation, startup, and shutdown of the washer water recycle system.

Jan 1, 1999

By Osvaldo A. Bascur, J. P. Kennedy

Companies have installed powerful desktops for their personnel and instrumentation and control systems in their plants. These desktops are, in many cases, connected to a company intranet. Still, process engineers have to obtain their data manually. Engineers use process calculations from manually calculated averages from the plant; field operators collect equipment data on log sheets; and maintenance engineers collect critical information on log sheets. All of this information resides in individual machines. What are the strategic tools that will enable collaboration between them? How can operators, engineers, and managers access plant information to proactively increase their effectiveness in process troubleshooting, plant debottleneclung, aligning with business strategic and customer demand, satisfying environmental and safety regulations, developing capital projects, and implementing control strategies? A nonintrusive environment at the desktop is required to provide the process information to these workers. How can value be added to MS Windows technologies with the legacy systems at a minimum cost? There is no straight answer; however, there is a proven framework to leverage the large investments in new technologies. Objects and components are changing the way everyone relates to their computer and networks. Three examples will be described to demonstrate paradigm change. Today, process engineers can access data at the required level of detail for analysis of critical process variables at their desk or remotely. 1. Process Troubleshooting and Analysis: The engineer can develop an inferential calculation, trigger a process advisor to deter- mine the behavior of the units for the last day, and get the population of a set of batches (heats, blocks, rolls, sheets, etc). 2. Process Control and Optimization: The engineer can connect to a process simulator at steady state or a dynamic simulator of the process to evaluate new control strategies or process unit line-ups and use the process simulator as a process observer for fault diagnosis. 3. Collaboration with Accounting and Maintenance: The engineer can review reconciled data and the process mass balances, suggest maintenance cleaning or recalibration of flowmeters, and evaluate key control performance of all advanced controls.

Jan 1, 1999

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched. A new paradigm divides pillar failure into three categories:

Jan 1, 1999

By James R. Hunter, Sandra K. Zacharias, Ursula M. Franklin

Archaeometallurgical remains can be a valuable source of information about past technological activities and, by inference, the societies that undertook them. Material traces of former metal-producing or metal-working centres can include raw materials, products, or metallurgical installations such as mines, furnaces or forges. Of these remains, the most common is slag, often left undisturbed since its original production. Physical and chemical analyses of archaeological slag and metal can often reveal the processes and materials involved in their formation. Mineral composition and softening temperature of a slag, for instance, can indicate the conditions of the metallurgical operation, such as temperature and atmosphere and, thus, help identify metallurgical processes which took place at a site(1). The present report illustrates the value of such analysis. Metal-working remains from Sainte-Marie among the Hurons, near Midland, Ontario, on the south side of Georgian Bay have been analyzed in order to determine the techniques and processes used by the 17th-century blacksmith who worked at the mission headquarters from 1642 to 1649. Samples were selected from a very large collection of blacksmith refuse which was excavated from the site by archaeologist Kenneth Kidd in 1941-42(2).

Jan 1, 1999

By Jouko Kallionen

Advanced Flotation Technology is the application driven design of flotation cells to achieve the optimum performance for each type and grind of flotation. This can be applied to roughers, scavengers, cleaners and specialty cells such as those to float hydrocyclone underflows in both primary and regrind circuits in order to reduce overgrinding. Standard, engineered, components are matched to provide mechanism design and cell dimensions for each case according to feed parameters and flotation type. Advances in process control have been achieved with high level controls and operator information data. This has gained a higher degree of understanding of cell operation and ore type being processed. Excellent results of this Advanced Flotation Technology in large scale porphyric copper ore have been achieved and designs through 7000 cu ft (200 m3) are currently available for high capacity concentrators. This paper will detail how flotation cells are more responsive to the exact requirements of the duty specified.

Jan 1, 1999

By T. F. Torries

Identifying high value areas of unmined coal when large quantities of coal are available relative to annual markets is difficult because of the uncertainty of when the coal is to be mined. A GIS based methodology developed to value reserve coal in a producing coal region for the purpose of ad valorem taxation also identifies high value areas for mining investment. The methodology is unique in that it accounts for most mining, environmental, and market factors to determine when specific properties are to be mined. The methodology and data base are useful for directing regional exploration and acquisition activities toward most favorable areas.

Jan 1, 1999

By I. Gaballah

Jarosite contains up to 15 % of heavy metal compounds 'HMC'. The current waste disposal methods will not be allowed in the near future due to new environmental regulations and pollution risks. For these reasons, thermal treatments of raw or decomposed jarosite, in controlled atmospheres, were investigated. The aim of these treatments is to decontaminate the jarosite and/ or to recover the HMC for recycling. According to physico-chemical characteristics of the samples, the thermal treatments in controlled atmospheres N2, CO+N2 and C12+air lead to the extraction rate that vary from 93 to 98 %. Heavy metal compounds were separated by cooling the gaseous phase. The treatments' residue was almost free from HMC. Between 700 "C and 800 "C, the chlorinating treatment was successful of eliminating more than 97 % of HMC contained in four different samples.

Jan 1, 1999

By H. Kempton

New methods for remediating metals-contaminated groundwater include in-situ emplacement of highly adsorptive substrates to permanently retard solutes. Substrates are introduced by sequential injection of soluble components that precipitate in the aquifer, forming a permanent high-retardation zone. This method overcomes the factors that limit pump-and-treat remediation; i.e, long-term source loading and slow desorption. Column tests demonstrated efficient substrate emplacement, increasing retardation coefficients of Cr(VI) by 20 and As(V) by 40. Similar effectiveness is expected for other heavy metals. Simulations using a coupled advective-geochemical model accurately matched substrate emplacement and arsenic attenuation, allowing extrapolation to other constituents and larger-scale applications.

Jan 1, 1999

Soil improvement technologies have been widely employed over the recent decades to overcome tunnelling problems in difficult grounds, their range of application growing proportionally to the technological development. The constant advancement in the different mechanical (flexible and more powerful equipment) and electronic (enhanced reliability and direct quality control) aspects of these technologies, fostered the confidence of engineers and tunnellers and, ultimately, allowed the entire tunnel industry to approach difficult excavations in a safer and cost effective manner.This paper outlines the main features of commercially available soil improvement techniques, with particular emphasis on permeation grouting and jet grouting. These two technologies, developed concurrently in Europe and Japan, and there customarily adopted in the design of underground structures, have known extensive and extreme applications worldwide in recent years. Case histories and current practice of soil improvement techniques, as they apply to tunnelling, are also rendered.

Jan 1, 1999