Search Documents

By Veliko Kertikov

Complicated processes of heat exchange and evaporation, leading to changes in the temperature and humidity of the ventilating air flow, take place during the driving of headings. In the case when virgin rock temperature is high, the increase in air temperature and humidity is significant. This causes a deterioration of climatic conditions in the headings. Procedures for predicting the changes in air temperature and humidity are discussed, together with appropriate calculations and computer programmes. Predicted results for example scenarios are used as a background for the selection of approaches and means to improve the climatic conditions in a dead-end heading using auxiliary ventilation.

Jan 1, 1997

By T. L. Carstensen

The Miami In-situ mine of BHP Copper is located in Globe-Miami, Arizona. The mine leaches mineralized leach capping over a supergene enriched sulfide deposit, and has produced over 500 million lbs of copper during the last 50 years. The Miami unit has identified several opportunities to enhance and expand in-situ production. A computer block model consisting of strict geologic controls, mineralogy, and metallurgical data was developed to assist in the determination of the leachable copper resource. An understanding of the accessibility and solubility of the resource to leaching solutions and the integration of hydrogeologic and hydrometallurgical information was necessary for completion of this project.

Jan 1, 1997

Miners and explorers in New Zealand are expected to consult with stakeholders, keep out of core conservation areas, and operate a high standard of environmental management and rehabilitation. These requirements are not difficult to meet, but many of the industry's own actions have brought it to a low level of general public esteem in New Zealand. Reasons for this are discussed, drawing examples from the Maruia Society's experiences with the industry since the mid-1980s. The boundary between core conservation areas and other land is not easily drawn, and the Maruia Society has sought to work with the mining industry to promote legislation for net conservation benefit trade-offs. However this initiative was not successful. Today the industry, unlike most other major industry sectors in New Zealand, has no accord with the country's conservation movement.

Jan 1, 1997

By B. R. Johnston, K. D. Streeter

"ABSTRACTCoal Mountain Operations is the newest of Fording Coal’s operations although it is the oldest in terms of its historical production. In October, 1994, Fording purchased the former Corbin Creek/Byron Creek Mine. The mine is located in southeastern British Columbia, approximately 150 air kilometers from Calgary, Alberta. It was first developed in 1905 and has gone through a variety of owners in its 90-year history.This paper will deal with the remobilization strategy and the mining plans for the operation which are being implemented to make this operation competitive in the world export coal market. IntroductionIn October 1994, following a due diligence process, Fording Coal Limited purchased Coal Mountain Operations from Corbin Creek Resources, an employee group which had previously owned the mine. The purchase awarded Fording Coal Limited with 100% of the assets, and control of all the coal leases at Coal Mountain.The mine is located in southeastern British Columbia, southeast of Sparwood at the hamlet of Corbin, (Fig. 1).Rehiring of laid-off employees started in November 1994, with mining activities also recommencing in November. The coal preparation plant was restarted in December with one shift, went to two shifts in January 1995, and had four-shift, full-time operation in April 1996."

Jan 1, 1997

By T. Tempel

In 1994 Newmont Gold Company commissioned a 2.5 Mt/a refractory gold ore roasting plant near Carlin Nevada. Many unique characteristics of this facility required use of specialized materials of construction in the areas of dry grinding, roasting, gas cleaning, and sulfuric acid production. Process conditions and design criteria that necessitated the use of special materials include; siliceous and abrasive ore, low roasting temperatures, gas streams with high concentrations of oxygen and sulfur, and stringent environmental regulations. Materials selected for use were ceramics, corrosion resistant steels, high temperature steels, and high temperature polymers, lead, polypropylene and low flammability PVC.

Jan 1, 1997

By V. S. Sastri, Elboujdaini. M.

"Economics of wear in mining industry and methods by which wear cost may be reduced will be discussed.IntroductionCanada loses more than $5 billion annually due to friction and wear (Table 1). It is estimated that about $1.3 billion, or about 25% of the losses, could be saved through better application of existing technology (Table 2). It should be noted that the costs given in Table 1 and 2 refer to 1986. The losses due to friction and wear and the savings would be much higher in 1996. Tribology combines the many branches and specialties in science and technology concerned with understanding and combatting friction and wear. Specifically, tribology is concerned with the design and manufacture of sliding and rolling bearings, piston rings, gears, cutting tools and other devices in which surfaces interact, in sliding or other relative motion. Tribology is concerned with the correct use of materials for interacting solid surfaces, with the interaction of the surfaces with the lubricants, with the chemistry, physics and use of lubricants. It is concerned with the reduction of friction and wear and the avoidance of associated failures in machinery. Similar tribological components such as bearings are used in different technologies and similar tribological problems such as abrasive wear occur in different industries. Thus, tribology is in itself a generic science and technology, concerned with the generation and dissemination of knowledge on friction, wear and lubrication, and the application of the knowledge, to a wide range of industrial products and equipment, from ploughs to space equipment, from prosthesis to engines, from washing machines to railways, from computers to power stations, from paper mills to mines. Avoidable losses due to friction and"

Jan 1, 1997

By T. Ritzel

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels at Cyprus Sierrita. The predictive program was initiated by Cyprus Sierrita and P&H Mining Equipment at the Cyprus Sierrita Mine in Tucson, Arizona during August of 1996 on the P&H model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Jan 1, 1997

Last evening, in Auckland, I heard the Chairman of Heinz US, Dr Tony O'Reilly (who, in addition to Heinz's ownership of our largest food processor, also has substantial personal investments in this country), advocate New Zealand as a 'regional corporate capital'.   Why would someone like Dr O'Reilly hold that view? No doubt, as one of Ireland's great rugby players of the 50s and 60s, he admires at least one thing that we do very well (confirmed again in Dublin over the past weekend). But that's not sufficient to support such a view.   He cited many reasons for preferring New Zealand over, say, Sydney, Australia, calling this 'the most rational in which to locate [an] international headquarters', including û +         we have no capital gains tax; +         a more 'pro-business environment'; +         a 'first class' legal and banking system; and +         a 'simple political system'.   I can find no better 'text for today's address.

Jan 1, 1997

By J. R. G. Williamson

The Mining Division of Iscor, an integrated minerals and metals company, has recently completed a feasibility study for the establishment of a new heavy minerals mine and smelter in the Richards Bay area of KwaZulu-Natal, South Africa. The mine will produce a heavy mineral concentrate containing ilmenite, zircon, rutile and leucoxene which will be beneficiated at a central processing complex close to Empangeni. The ilmenite will be smelted to produce high-grade titania slag and pig iron for export. The ancient dune containing the mineral deposit is located some distance inland of the coastal dunes, and the sands contain a high proportion of extremely fine material which must be extracted ahead of the gravity separation process. Of the 56 million tonnes to be mined annually over the ten-year life of the mine approximately 23,4%?a total of 13,1 million tonnes of minus 45 micron residue fines?will have to be disposed of in a containment facility. The origin of the fine material is from the weathering of amphibole minerals. The remaining coarse sands will be returned to the mined area to re-create the original dune configuration. A number of options for the disposal of the residue fines have been examined and specialised laboratory tests undertaken to determine the deposition behaviour of the fines. The final solution involved the use of a ?sub-aerial? technique for deposition of fine material in a disposal facility. The resulting arrangement will adequately meet technical and environmental criteria. Upon closure after 10 years of operation, the surface of the disposal facility will be returned to sugar cane cultivation The paper refers to the various options considered and describes the problems associated with competent disposal of the residue fines and the development details of the final disposal facility.

Jan 1, 1997

By M. R. Barkhudarov

Semi-solid metal can be formed into useful products of near net shape and high quality. Use of this method has been limited, however, because of the difficulty of working with metal in the semi-solid state, which has strong shear rate, temperature and time-dependent properties. In this paper we describe a thixotropic model and apply it to the problem of small metal droplets impacting on a flat plate.

Jan 1, 1997

By J. T. Hanks

Process development is one of the principal tasks required in the course of turning an exploration discovery into a mine. Exploration geologists should have an understanding of the more important metallurgical processes and the test work required for each process. The paper discusses the important metallurgical processes, the test work and sample requirements for each, and the costs and time requirements to accomplish the testing. The limitations of reverse circulation drill samples for metallurgical testing are discussed. The level of process definition required to support engineering studies: scoping, pre-feasibility and feasibility studies are also described.

Jan 1, 1997

By Y. Champoux, N. Atalla, R. Oddo, C. Lesage

"Percussion drills are the source of the most serious noise problems in mining activities, due to their extremely high noise levels(114-122 dB(A)) and widespread use(Bartholomae and Stein, 1988). Percussion drills will continue to be widely used to drill small diameter holes in hard rock because no other method seems to be economically avail-able to replace them (Boillat et al., 1993).Many studies (Danière, 1991; Hawkes etal., 1977a; Jensen and Visnapuu, 1972;Leblond et al., 1976; Milette, 1989) were con-ducted to determine the major noise sources of percussion drills. The exhaust air of pneumatic drills, the hammer, the bit in contact with the rock and the drill rod have been identified as the major noise sources. A muffer can be used to reduce the exhaust noise and the hammer can be enclosed. The bit noise is considered to be of concern only at the beginning of holes. When all the available methods are used to reduce the noise of a percussion drill, the drill rod vibrations become the dominant noise source (Hawkes and Burks, 1979). However, the noise levels generated by this source remain high and future efforts should concentrate on reducing its radiation.Works by Hawkes and Burks (1979) and Hawkes et al. (1977b) for the U.S. Bureau of Mines provide the most complete description on the noise and vibration of percussion drill rods.The longitudinal and bending waves are the two most important types of elastic waves generated in drill rods. Among these, only the longitudinal waves contribute to the drilling rate. The bending waves are caused by non-centralized impacts, drill rod curvature and non-uniform bit/rock interface. Drill rod noise is generated by Poisson’s ratio expansions and contractions of the rod as the longitudinal waves travel up and down it and by transverse rod motions induced by bending waves. The radiation efficiency is much higher for bending waves than for longitudinal waves. Most of the impact energy is transformed into longitudinal waves, as expected for axial impacts. The evaluation of the relative contribution of longitudinal and bending waves to noise generation poses a very difficult problem for experimental, analytical and numerical approaches. It is, however, an important issue because the relative contribution of these two waves will guide future noise reduction efforts. It seems that very little can be done to reduce the noise radiation of the axial waves without affecting the drilling rate. The main difficulty that analytical and numerical approach-es face, in the evaluation of the relative contribution of the two waves, is that there is no adequate theory for predicting the bending vibrations from the factors that cause them. The experimental approach has, thus, been limited to test fixtures that do not adequately represent the boundary conditions, as well as by measurements obtained under real operating conditions from which it is difficult to establish the relative contribution of the two types of waves. For example, Hawkes and Burks (1979) and Hawkes et al. (1977b) used a test fixture with free-free boundary conditions and made no clear link with measurement under real operating conditions. Rather, they have based their discussion on a simple model. Many authors assume that fexural waves are the main noise source on drill rods. However, measurements have been somewhat contradictory and researchers are still unable to state with certainty that this is indeed the case (Lednik et al., 1988)."

Jan 1, 1997

By Dale S. Preece, J Paul Tidman, Stephen H. Chung

"A discrete element computer program named DMC-BLAST (Distinct Motion code) has been under. development since 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employsexplicit time integration and uses spherical or cylindrical elements that are represented as circles in2-D. DMC-BLAST calculations compare favorably with data from actual bench blasts (Preece et al,1993)."

Jan 1, 1997

In the last 40 years nuclear energy has taken its place as a major source of electricity worldwide. It now produces 17 per cent of the world's electricity and could conceivably produce a higher proportion, to displace some six billion tonnes of carbon dioxide emissions per year. Concerns about global warming and environmental quality now underline the virtues of nuclear electricity among alternative sources of energy. Global electricity demand is rapidly increasing as a proportion of total energy usage. The proportion has doubled since 1960 and the demand is expected to increase at least 75 per cent between now and 2020. The source of this extra capacity, and the replacement of present capacity, raise questions with major resource and environmental implications. Today nuclear energy is a mature technology. Over 1200 nuclear reactors have been built and operated, some of these have been decommissioned, and among the 440 reactors in commercial operation the first advanced reactors are now entering service. Some 8000 reactor-years of operation have, with the sole exception of Chernobyl, shown nuclear energy to be extremely safe and reliable. High-level wastes are being managed properly and in different parts of the world two strategies are applied to this. Australia has a major role as a long-term supplier of uranium, since it holds almost 30 per cent of the world's reserves. This, along with an impending sellers' market for uranium, is making it an opportune time to develop new mines here. However, after several decades of concern about civil nuclear energy contributing to the arms race, we now have uranium liberated from nuclear weapons stockpiles being diluted for use in civil reactors, which will supplement ex-mine supply. The public acceptability of nuclear energy remains the critical factor in its future and hence in ours.

Jan 1, 1997

By Roy A. Bell

A 200-foot diameter, 72-foot high petroleum storage tank was built in a hillside ravine where a portion of the site contained soft clay fill. Soil-cement piles, 40 inches in diameter and up to 38 feet long, were installed to support the tank shell and ringwall, and a portion of the tank floor by drilling into the stiff to hard underlying soils and weathered bedrock. The goal was to provide a strong enough foundation to resist the seismic tank shell loading and to minimize differential settlement of the tank shell to avoid out-of-round clearance problems between the shell and floating-roof. A cantilevered retaining wall up to 8 feet high was constructed around a portion of the tank perimeter by inserting steel H-beams into soil-cement piles. The cantilever soldier piles for the retaining wall were installed from a temporary earth embankment on the hillside directly over the top of the wall. The temporary embankment was then removed and the tank pad was cut to grade in front of the soldier piles. Some of the soil-cement piles for both the tank foundation and retaining wall could not be advanced to design depth because the drill/mixing tools could not penetrate to the required depth in the hard soils/bedrock. Smaller diameter borings (22 inches in diameter) were drilled through the centers of the short-of-design soil-cement piles to the design depth and then backfilled with concrete.

Jan 1, 1997

By Thomas Sisley, Jozef Zurawski, Richard Switalski

Hilltop Interceptor Contract G is one of the segments of the wastewater control system in the greater Cleveland area. The tunnel is a relief interceptor constructed by the Northeast Ohio Regional Sewer District to minimize combined sewer overflows in the Easterly Service Area. The design study identified the need for a 3.35 m (132 in) diameter, 3.35 km (11,000 ft)in-line storage conveyance tunnel to be constructed at depths of 30 to 70 m (100 to 230 ft).Six structures for access, future flow drop, work shafts and overflow control were required to complete the system. The interceptor reduced the design peak flow from 12.5 m3/s(285 mgd) to 6.1 m3/s (140 mgd) by detaining in line 22,800 m3 (six million gallons) of wastewater.

Jan 1, 1997

By R. J. Chesher, J. C. Anzalone, T. F. Krusmark

The BHP Copper Refinery at San Manuel, AZ employs conventional electro-refining technology, plating at a current density of 335 A/m2 on six kilogram copper starter sheets. In 1995, a combination of variable anode chemistries and increasing current density in the tankhouse created periods of increased bismuth in cathode. Bismuth in electrolyte was minimized by bleeding electrolyte to the nearby BHP leaching facility. However, the expected drop in cathode bismuth was not achieved. Investigations indicated that starter sheets contained a significant concentration of bismuth. The bismuth was found to occur in combination with antimony on the surface of the sheet adjacent to the mother blank. Studies were conducted to determine the mechanism by which Group VB elements are incorporated into the starte sheets. Operational practices were introduced to minimize bismuth in starter sheets and improve cathode quality.

Jan 1, 1997

By Jennifer Mager, G. P. Martins, Dean Mussatti

"The role of lead, at low concentrations in high pH cyanide-electrolytes, on the dissolution behavior of gold, has been a topic of scientific and industrial concern for well over a century. The recent paper by Kondos et al [1] at CANMET (1995) this continuing interest and apparent importance. Nevertheless, the mechanism(s) by which this (and other heavy metal) component influences the electrodics of this electrochemical system has still not been unequivocally demonstrated. Instead, several plausible hypotheses, by pioneering researchers in this field, have been advanced and reiterated OVer the ensuing years. While it is generally accepted, based on equilibrium elctrode-potential calculations, that reduction (or co-reduction when oxygen is present in the electrolyte) of lead on the gold surface may occur due to cementation (contact reduction), the cemented lead has never been characterized. The work presented has reexamined the role of lead in this system, by delineating the species distribution of these system components and by interpreting the results of potentiodynamic studies in conjunction with SEM analyses of a gold electrode.1. INTRODUCTIONThe leaching of gold ores in cyanide electrolytes has been practiced for well over a 100 years. Research conducted on this topic has been primarily focused on the effects of operating parameters such as concentrations of oxygen and cyanide, and the pH of the electrolyte; or the leaching behavior of carbonaceous and sulfitic gold-bearing materials.Mechanisms by which pure gold is leached in alkaline cyanide media, with oxygen serving as the oxidant, have been subjected to continual examination and re-examination in the published technical literature during this century. Recently, it has been speculated that without the presence in the electrolyte of trace heavy metals, such as lead or mercury, that gold would not be leachable. Researchers who have tackled this topic, have either considered heavy metals to be a natural occurrence in these systems and ignored the role they may serve in the leaching process, or they have deliberately focussed on controlling their concentrations in the system to undetectable limits. As a result, conflicting findings have been reported for what would appear - depending on the details provided in these reports - to be identical systems."

Jan 1, 1997

By S. Manning, W. Morris

Mineral exploration assessment file information has long been considered a useful resource for developing mineral exploration strategies, and one of the most common data sets fled in assessment reports is ground magnetic surveys. The new Earth Resources and Land Information System database (ERLIS) now provides a method for rapidly accessing all references to a specific area through a series of raster images. The ERLIS provides access to the Assessment File Research Imaging (AFRI) database which comprises geo-science mineral exploration assessment file data, Mineral Deposits Inventory (MDI), together with provincial aeromagnetic data from the Ontario Ministry of Northern Development and Mines(MNDM). Conversion of the raster images of ground geophysical data to vector data files together with the concatenation of grids from adjacent claims provides a method for constructing high resolution magnetic regional images. The value of this resource is demonstrated through the construction of a single composite magnetic image derived from eight assessment file grids for an area south of Kirkland Lake, Ontario, within Pacaud and Catharine Townships. The composite grid of magnetic data provides a map with resolution that is not achieved by currently available Ontario Geological Survey airborne data sets. Details contained within the new high resolution image, permit the differentiation of lithologies and their boundaries, fault orientations and the location of alteration zones with magnetic response.

Jan 1, 1997

By E. Molleman

This paper reports on testwork exploring the dissolution/reprecipitation reaction: ZnS + 2HCl ? ZnCl2 + H2S, as part of a process for the production of pure ZnS. In spheroidal form, this would constitute a premium fonn of zinc refinery roaster feed enabling the production of pure ZnO. The research focused on the influence of proton activity on dissolution of zinc concentrates from Brunswick Mining & Smelting, Red Dog and Tara. The results and thermodynamic data suggest that the three concentrates contained significant amounts of the more reactive mineral wurtzite, although XRD analysis showed mainly the presence of the mineral sphalerite.

Jan 1, 1997