Search Documents

By Christopher Mark

The Bureau of Mines has recently completed a comprehensive study of coal strength. More than 4000 individual test results from over 60 seams were extracted from the literature and combined in the most complete data base of the uniaxial compressive strength of coal ever assembled. In addition, more than 100 case studies of in-mine pillar performance were available in the Analysis of Retreat Mining Pillar Stability (ARMPS) data base. Statistical analysis of this wealth of data has yielded valuable results. The data shows clearly that the "size effect" is related to coal structure. The widely-used Gaddy formula, which predicts a significant strength reduction as the specimen size is increased, was found to apply only to "blocky" coals. For friable coals, the size effect was much less pronounced or even non-existent. Case histories of failed pillars are the best available data on in situ coal strength. This study found no correlation between the ARMPS stability factor of failed pillars and coal specimen strength. Pillar design was much more reliable when a uniform coal strength was used in all case histories.

Jan 1, 1996

Until recently, nickel laterite projects have been largely ignored, due to their supposedly higher treatment costs compared with sulphides, and to their perceived processing difficulties. A number of laterite projects in the 1970s were abandoned because of high capital and operating costs, while others experienced severe technical difficulties. Conventional wisdom had it that laterites would not be exploited until most of the sulphide orebodies had been depleted. Why then, have Australian mining and exploration companies started a resurgence of interest in the treatment of nickel laterites? It all began with the Bulong project, which has been under study since 1987, while more recently two further projects, Murrin Murrin and Cawse, have been initiated and are being fast-tracked to take advantage of the current high nickel and cobalt prices. A further project in NSW, Syerston, has also been investigated at bench-scale, but no further development has yet been announced. All these projects have the following advantages: 1. Good location near a major mining centre and,reasonably close to power, water, roads, accommodation and a developed service industry. 2. Straightforward, low cost mining. 3. Low cost of acid or sulphur. 4. Good to very good cobalt credits. In addition, there have been significant technological developments in the design and operation of high pressure autoclaves and high rate thickeners, as well as solvent extraction and electrowinning technology. This has helped to decrease capital costs and technical risks, and has allowed the development of alternative flowsheets to the existing laterite operations (Taylor, 1996).

Jan 1, 1996

By Milton Manrique

The thermal decomposition of zircon concentrates in a non-transferred arc thermal plasma flow reactor was investigated. The plasma torch was operated using argon-helium and argon-nitrogen mixtures as plasma gases. The effect of power, feed rate and zircon particle size was studied. Products were characterized by XRD, SEM, TEM and chemical analytical techniques. The average size of the product was in the submicron range. Free energy minimization plots were used to predict the behavior of the system under different operating conditions. A kinetic model to describe the different stages of the thermal decomposition process is proposed. The results of this investigation showed a significant segregation process where the zirconia-rich product is collected in the reactor while the silica-rich product is collected in the filter. TEM analysis indicated that silica vapor is condensed on the surface of the zirconia particles.

Jan 1, 1996

By H. Lyn Bourne

This marks the 15th consecutive year for this column. During 1995, readers were asked to supply royalty data for construction raw materials especially for states where none is available. The response was discouraging and royalty data are still missing for several states for either sand and gravel or crushed stone. Several readers have said that this article has merit but more new information is needed to justify its continuation. Several articles and pieces of news relative to mineral royalties appeared in the trade journals. R. Lee Aston (E&MJ, November, 1995, p. 16N) described South Australian royalties as amended by the government in1994. The royalty rate (a percentage) was lowered but the assessed value for minerals was raised and the current rate amounts to 20 cents//t (18 cents/st).

Jan 1, 1996

A modified Cuprex Metal Extraction Process (CMEP) leach process was used to extract Cu. Ni and Co from a complex sulphide concentrate. The standard leach was modified to a two-stage countercurrent leach which provided emf control of the copper SX feed and minimized iron dissolution. A flowsheet was developed to recover the base metals and silver from the leach solution and gold and platinum group metals from the leach residue which was predominantly elemental sulphur. Techniques required to maintain an iron balance in the system including pressure oxidation and solvent extraction are described.

Jan 1, 1996

By Laxman M. Amaratunga, David N. Yaschyshyn

"In the mining industry several types of fills are used for backfill operations. They are broadly categorized into three basic types: rock fill, hydraulic/slurry fill, and paste fill. Recently, paste fill has become the popular alternative for backfilling because of its many environmental and operational advantages including its ability to use total tailings, both fine and coarse fractions.Amaratunga and Annor (1989) first presented the concept of agglomeration of fine tailings, which are otherwise excluded from backfilling, for utilization in backfill as a readily available supplementary fill material. Previous experimental work investigated the use of agglomerated fine gold mill tailings in low density slurry fills (60 -70% pulp density), consisting of varying agglomerate and tailings compositions.This paper presents the ongoing research into utilizing these agglomerates in a high density paste fill (70 -85% pulp density). Various binder dosages, curing period and combinations of pellet to tailings ratios were studied. Slump of the raw fill and compressive strength of the cured fill were examined. Results from the above study indicate that agglomerated tailings paste fill (ATPF) has superior strength characteristics when compared to total tailings paste fills.IntroductionThe Canadian mining industry produces more than 500 million tonnes of tailings and waste rock annually. These tailings consist of a coarse fraction and a fine fraction and can be either reactive (acid generating) or non-reactive. Most mining operations utilize the coarse fraction for backfilling while the fines have been traditionally disposed of in surface tailings ponds. Recently, paste fill has been developed which uses a fraction of the fine tailings (10 - 30% w/w of >45 µ,m) in the fill. This development allows a mining company to use a portion of the fines for backfill, but still requires surface impoundment of the unused portion of fine tailings. Reactive tailings have the added problem of generating acid after being oxidized in the presence of air and water. Treating acid mine drainage (AMD) seepage from these ponds has proven to be a costly environmental problem and long term liabilty.One practical method to reduce the environmental impacts associated with the tailings pond and to modify the physical and chemical properties of the fine mill tailings so that they can be utilized and disposed of in an environmentally safe manner through surface or underground applications is through agglomeration using the Cold-Bond Tailings Agglomeration technology (CBTA). Amaratunga and Annor (1989) first presented the concept of agglomeration of fine tailings for use as coarse aggregates for underground backfill, gravel or surface covering material. CBT A reduces the necessity of impounding tailings on surface while providing a suitable coarse aggregate resource material for practical use. Although the CBT A technology has been mainly limited to pelletization agglomeration alone, other forms of agglomeration like pressure agglomeration which include the techniques of briquetting and extrusion have also proven successful (Amaratunga, 1995)."

Jan 1, 1996

By Mustafa Akser

The Pipestone Lake anorthosite complex in Manitoba, Canada, was recently been re-identified as a potential source for titanium, iron, and vanadium. The present study utilized a 350 kg hard rock sample, which originated from the "Main Central" zone of the deposit. Commercial pilot-size equipment, such as dry low intensity roll magnets, wet high intensity magnets (WHIMS), and high tension electro-dynamic roll separators, was employed. As products, ilmenite up to 48.5% TiO2, and magnetite concentrates up to 87.9% Fe3O4 with 5.25% TiO2 were obtained. The majority of the vanadium reported to the magnetite concentrate. Subsequent characterization of various separation products shed light on the potential grade and recovery of the minerals from this deposit.

Jan 1, 1996

By Thomas C. Shrake

The Lomas Bayas copper property is located93 km (58 miles) east of Antofagasta, Region II, Chile (Fig. 1). The deposit was discovered in 1880. The deposit produced intermittently until 1992. Production at Lomas Bayas took place in high-grade veins and breccias mined underground. During 1991, Empresa Minera Mantos Blancos SA (EMMB) optioned the property from Compania Doña Ada SA. Doña Ada maintained the right to continue mining the ores by open-pit and block-caving methods and hauling the ore to its plant located60 km (37 miles) to the north. EMMB conducted exploration and column test programs. On May 9, 1994, Compania Minera Gibraltar Ltda.(CMGL) signed a purchase option agreement to acquire the Lomas Bayas property. CMGL conducted 8,612 m(9,490 ft) of reverse-circulation drilling, 2,028 m (6,650ft) of diamond drilling, a series of metallurgical tests and geologic mapping. The company then decided to exercise its purchase option.

Jan 1, 1996

By W. K. Katoto

The Tailings Leach Plant (TLP) of the Zambia Consolidated Copper Mines Ltd at Nchanga was commissioned in 1974 as the world's first largest successfully operated agitation leach SX-EW plant for copper production. The design, development and operation of the plant soon after commissioning termed as TLP stage II has been described by Holmes et al (1). In the initial phase the plant was designed to treat approximately 25,000 tonnes per day of current flotation tailings from the Nchanga Concentrator operations, and had a design capacity to produce 75,000 tonnes per annum of copper. Further expansion took place in 1986, and TLP stage III was successfully commissioned to treat an additional 20,000 -25,000 tonnes per day of large reserves (over 135m tonnes) of reclaimed tailings stockpiled since the early 1930's in four paddock type tailings dams (T01 to T04). The salient feature of TLP stage III expansion described by S K Mwenechanya et al (2 -3) was the installation of the world's largest Horizontal Belt Filter Plant with 26 filters each of 80 m2 filtration area.

Jan 1, 1996

By F. P. Hassani, A. Hara, M. Momayez

To be competitive on the international market, the Canadian mining industry must reduce its costs, increase its productivity and maintain a high standard of safety. There is a great need today for improved methods that would allow the detection of geological structures in advance of mining to reduce dilution and the monitoring of underground structures to increase safety. This will facilitate planning for optimum exploitation of the mine and to increase production at lower costs. This paper discusses two examples of more efficient mine planning using new technologies such as Ground Probing Radar (GPR). In Kidd Creek mine, GPR technology was used at the 2500and 2600 levels to (1) monitor the stability of the sill pillar; (2) locate the presence of disseminated sulphide pockets in the sill pillar for extracting the mineral content; (3) monitor the stope backs and wall structures to evaluate the effect of on-time filling sequences; and (4)assess rockfill quality in terms of the presence of voids and fractures within the rockfilled areas. In the New Brunswick coal mine in Minto, GPR was used along with core log data to map and construct a 3D block of a section of the bench showing the relative position of different layers overlying the coal seam.

Jan 1, 1996

By Matthew C. Binsfield

The simultaneous electro winning of zinc and manganese from waste water treatment plant sludge was studied as a part of the overall research program, which was conducted to develop the methods for removal of environmentally hazardous metals from the Bunker Hill Superfund Site. This paper discusses the electrolytic method for recovery of zinc and manganese from the solution produced by leaching of sludge with S02 + H2S04. After three stage purification of the leaching solution, zinc and manganese were electro won simultaneously in an undivided electrolytic cell. Zinc was deposited on an aluminum cathode, while manganese was simultaneously produced (as Mn02) on a lead silver anode. The electrowinning parameters studied were the effects of: temperature, current density, electrode material, spacing of electrodes, composition of electrolyte, and electrolyte additives. Anodic and cathodic efficiencies were 30 and 91%, respectively. In light of the process design parameters discussed in the paper, which are affecting the electrowinning, these efficiencies were found as acceptable with regard to the quality and marketability of the products.

Jan 1, 1996

By G. Heinrichs

This paper is intended to provide information for one to be able to determine the slurry system head curve for pump applications. The slurry characteristics are the basis for what the size, material of construction, and critical carrying velocity of the pipe will be. The system head curve is adjusted by use of the pipe friction coefficient factor and slurry derate factors. An example using multi-staging of slurry pump curves is presented to compare the wear life relationship of pump parts for a tailing pipeline system head curve.

Jan 1, 1996

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements set out on pages 272 to 277. These financial statements are the responsibility of the Institute's Council. Our responsibility is to report on these financial statements. We have conducted our audit in accordance with generally accepted auditing standards. These standards require that we plan and perform the audit to obtain reasonable assurance that, in all material respects, fair presentation is achieved in the financial statements. The audit included an evaluation of the appropriateness of the accounting policies, an examination, on a test basis, of evidence that supports the amounts and disclosures included in the financial statements, an assessment of the reasonableness of significant estimates, and a consideration of the appropri¬ateness of the overall financial statement presentation. We consider that our auditing procedures were appropriate in the circumstances to enable us to express our opinion presented here. In our opinion these financial statements fairly present the financial position of the Institute at 30th June, 1996, and the results of its operations for the year then ended in conformity with generally accepted accounting practice.

Jan 1, 1996

By K. Biswas

A finite-element algorithm was developed for an axisymmetric heat-transfer problem involving phase change. The finite-element treatment of the phase-change problem was dealt with by using the enthalpy method. The finite-element algorithm was subsequently applied to model the heat exchange between mine ventilation air and frozen ground in the presence of roof bolts in an underground mine with permafrost. This paper analyzes a single bolt in the problem domain with the convection boundaries at the roof level of the mine airway. A short-term study, comprising the evaluation of roof bolting (friction-anchored type), was conducted, and recommendations were made regarding the applicability of roof bolts as a support system for a given thermal condition.

Jan 1, 1996

By Lee Browne

The transformation of Peru’s Tintaya copper project from a state-owned company to a private company is under way and the results have been successful. Since Magma Copper Co. assumed operating management in December 1994, production and costs have improved dramatically. To understand the transformation of Tintaya, the transformation of Magma Copper must also be understood.

Jan 1, 1996

By Vaughan R. Voller

In many high temperature processes involving liquid melts the common practice is to solidify a fraction of the melt adjacent to the containment wall; a practice that can provide protection of the structural components of the process. The position, shape and transient behavior of these so called "skulls" and/or "ledges" are directly dependent on the thermal process conditions. This paper presents a model of a generic ledge process that can predict the steady shape of a ledge. Two numerical implementations are presented and compared: (1) based on a space grid of continuously deforming finite elements (2) based on a conjugate grid of fixed control volumes and deforming boundary elements.

Jan 1, 1996

By Wm. Mark Hart

High horizontal stresses and shear failure have been considered the major reasons that cause entry roof failure and falls for underground mining. Therefore, reorientation of the current mining systems or layouts or using angular crosscuts in mains or gate entries becomes more popular if a greater than normal horizontal stress is measured. However, reorientation of the current mining systems or layouts is always expensive and use of the angular crosscuts may weaken the pillar structure at corners. Therefore, cautions must be taken before any decision related to reorientation of the current mining systems or layouts or use of angular crosscuts is going to be made. In order to prevent entry roof failure and falls, the following two issues must be carefully examined and fully understood: 1. Which one, shear stress or tensile stress, is going to be blamed for entry roof failure? 2. Which one, horizontal stress, vertical stress, or local geological weakness plays a major role in entry roof failure and falls? This paper analyzes the mechanisms of entry roof failure and falls for underground mining in general examines the roof fall history at Springvale Colliery, and proposes the means of preventing roof failure and controlling roof falls for Spingvale Colliery in particular.

Jan 1, 1996

By Y. Suzuki, J. Nagao, Y. Ueda, K. Shimokawa

"A Ti- Ni intermetallic compound could be formed rapidly from Ti and Ni powder compact with SHS process. Microgravity experiments using a drop shaft are carried out, This report shows the effect of microgravity or high gravity on formability of an intermetallic compound. It is concluded that the specimen forms a porous and nearly amorphous alloy by rapid cooling under microgravity but with rapid cooling under high gravity after microgravity, the specimen forms a uniform and dense structure with better crystallinity.IntroductionTi - Ni inter1etallic co1pounds have been produced and have beco1e si1ilar to the a1orphous and porous structure as a result of the SHS (Self Propagating High-te1perature Synthesis) process under 1icrogravity. SHS process is being applied to the synthesis of cera1ics and inter1etallic co1pounds (1). The technique is characterized by a large a1ount of heat being emitted within a very short ti1e interval as regards the sistering reaction. One SHS process, acco1panying 1elting by a reaction was observed, and that was due to the quick heating of a Ni-Ti co1pact containing 50 ato1ic percent of Ti under a low pressure (2-4). In this report, we have researched the use a drop shaft which is 1ore effective during a short ti1e under 1icrogravity and high-gravity, so as to obtain high dense speci1ens with the exception of porous specimens (5). Mechanical properties of each specimen were esti1ated from these 1icro-structures with a discussion about the effect of changing gravity regarding 1elting and solidification of the Ti-Ni intermetallic comounds."

Jan 1, 1996

By Alan A. Campoli

The U.S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996

P.T. Freeport Indonesia's latest expansion has increased total mill throughput to 125,000 dry metric tonnes per day. The most recent expansion included the installation of a Semi Autogenous Mill designed to treat more ore than any other single SAG mill currently operating in the world. Also included in the expansion were two large ball mills, rougher and cleaner flotation including conventional and column cells and a regrind circuit. All equipment is supported by a modem distributed control system. This paper describes the design considerations, construction, commissioning and start-up of the SAG concentrator and support facilities and includes an overview of the oreflow and milling facilities.

Jan 1, 1996