Search Documents

By J. C. Franklin

The U.S. Department of the Interior, Bureau of Mines, has developed a data acquisition system to continuously monitor radon, working level, absolute pressure, temperature, relative humidity, and air velocity. Data have been taken in intake and exhaust drifts, working stopes, and sealed-off areas of positive and negative ventilated uranium mines. Radon emanation rates, ranging from 1.7- to 12.2 x 2 10-l4 Ci/cm /sec were determined in four mines. The ratios of short duration, primary fan shutdown time to radon normalization time were 1 to 2 and 1 to 4, respectively, for-negatively and positively ventilated mines. Blasting and slushing caused radon increases of 160 and 67 percent, respectively.

Jan 1, 1980

By M. J. Ferrante

New data on zirconium tetraiodide (ZrI4) have resulted from high-temperature enthalpy and X-ray powder diffraction studies conducted by the Bureau of Mines. These studies were undertaken as part of the Bureau's efforts to provide important thermodynamic data essential to the advancement of mineral resources technologies that can be employed with minimal energy requirements and minimal environmental degradation. Enthalpies were measured with a copper-block drop calorimeter. No transitions or other anomalies were found. Tabulated values are given from 298.15 to 772 K for relative enthalpy, heat capacity, entropy, and Gibbs energy function. Enthalpies are expressed in equation form and combined with data from the literature to calculate values of the standard enthalpy of formation and the Gibbs energy of formation. X-ray powder diffraction data indicate that ZrI4 is primitive cubic with a lattice parameter of 11.79 A and is isostructural with stannic iodide (SnI4).

Jan 1, 1980

In November 1969, New Zealand Steel Ltd pioneered the commercial use of the SL/RN solid fuel direct reduction process to make sponge iron as a feed material for electric arc furnaces. Serious process problems with the use of green balls and coal injection were progressively overcome. The process was developed by New Zealand Steel along a radical route, of feeding the fine grained raw ironsand concentrate and coal directly to the kiln. Contemporaneously with this development of direct reduction, steelmaking process innovations were made that enabled the arc furnaces to operate successfully with the high volumes of acid slag. The further expansion of New Zealand Steel's primary steelmaking capacity to replace the currently imported hot and cold flat rolled products is under consideration. The requirement to produce about 600 000 tonnes of steel slabs will be an opportunity to further modify iron and steel making plant and processes to optimise the economics. The conceptual and preliminary engineering selection of options is described.

Jan 1, 1980

By Nicholas G. Theofilos

The Bahamian economy weathered the worldwide recession of the last few years better than most developing countries. This was mainly owing to the ties between the tourist industry of the Bahamas and the U.S. economy. The mineral industry played a minor role in the country's economy. The chief mineral exports included an increasing amount of petroleum products horn the country?s 500,000-barrel-per-day refinery, steel pipe, salt, and aragonite. A 60,001)-barrel-per-day desulfurization facility was completed by Bahamas Oil Refinery Co. (BORCO) in Freeport. The project included vacuum gas oil desulfurization, hydrogen and sulfur recovery, steam generation, water desalinization, and offsite facilities.

Jan 1, 1980

By David K. Hylbert

This study investigated stratigraphic and structural causes of roof falls in room-and-pillar drift coal mines in nine mines in eastern Kentucky. A contract modification provided for remote sensing studies in the Dunkard Basin of West Virginia and Pennsylvania. Results of stratigraphic and structural studies of an earlier contract (H0133018) were applied to several new mines. It was found that similar rock sequences contributed to unstable roof conditions. Structure contour and isopach maps were found useful In projecting these trends together with fence diagrams. Using Landsat imagery, a direct relationship was found between lineament direction and the trends of rock jointing, roof fall zones, "snap top" zones and sandstone channels in the examples cited. It was found that, by analyzing lineament intersections, from 50 percent to 65 percent coincided with roof falls.

Jan 1, 1980

By P. B. Grote

The report provides a general description of DOM technology, sources for DOM technology, and identifies approaches and requirements for acquisition by the Enterprise of DOM technology by conventional means. The approaches identified assume the Enterprise enters into a contractual/ joint venture arrangement with an uncommitted and competent systems management firm at various stages of the DOM system acquisition process. The approaches provide for training through work/study as well as through direct participation in acquisition programs. The potential success of the alternatives are evaluated in terms of the likelihood of the acquisition of an ongoing Enterprise economic DOM operational capability. The study concludes that sources exist and that the Enterprise should under-take the development of its own technical capability through conceptual design prior to selecting its source for systems management expertise.

Jan 1, 1980

By James J. Scott

"In the two years since their introduction, Friction Rock Stabilizershave replaced40 per cent of the previously used fixtures in the metal and non-metal mines in the United States. The Friction Rock Stabilizer, or ""Split Set "" , is a mechanical rock stabilizing system which uses friction to prevent rock movement . The Split Set is a tapered, rolled, steel tube that is slotted along its length. As it is driven into a drilled hole smaller than its diameter, it compresses, pre-loading the surrounding rock. This paper discusses the uses and acceptance of the friction rock stabilizer in mines in the United States. IntroductionFriction Rock Stabilizers, commonly called Split Set™· Stabilizers, have been under development by the author and Ingersoll-Rand Company since early 1973. Five years of intensive laboratory and field testing led to their introduction to the metal mines in the United States in the fall of 1976. Actual sales started in February of 1977and, to date, over five million units have been marketed to metal mines. The present rate of usage is near 3 V2 million units per year, which is approximately 50070 of all roof fixtures used in the United States metal mining industry,Richard Hoppe, senior editor of Engineering & Mining Journal. , in an article in the February 1979 issue entitled ""Winning the Battle Against Bad Ground"", said: ""In hardrock mining operations in the western U.S., particularly underground uranium mines where exceedingly difficult ground is common, no roof support system has been accepted more quickly than the Split Set friction bolt invented by Dr. James J . Scott and developed by Ingersoll-Rand Co."" This paper describes how Friction Rock Stabilizers function and presents technical data to show the uniqueness of such systems."

Jan 1, 1980

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC, and was installed on a shuttle car in a conventional room and pillar mining section. The purpose of presenting the information is to prepare mine operators for proposed legislation that will require shielding on low-voltage trailing cables. Specifically, machine modifications are required to cable reels, packing glands, and couplers. Cable splicing is not as complex as expected but additional materials are needed in the kit and splice training is necessary. Even though shielding will cause some problems for the mine operator, it can reduce the hazard of electrical shock to mine workers. This paper will present information that mine operators can use to solve most of the problems that will be encountered if they are required to install shielded cables. The in-mine evaluation was funded by the U.S. Bureau of Mines.

Jan 1, 1980

By Annie G. Smelley

As a part of research conducted in its mission to effect pollution abatement, the Bureau of Mines, U.S. Department of the Interior, is developing a dewatering technique that allows for disposal of clay wastes, for reuse of water now lost with clays, and for reclamation of mined land. The technique utilizes a high-molecular-weight nonionic polyethylene oxide polymer (PEO) that has the ability to flocculate and dewater materials containing clay wastes. In laboratory experiments, coal-clay waste, potash-clay brine slurry, phosphatic clay waste, uranium tailings, and talc tailings were successfully consolidated. Coal-clay was te was consolidated from 3-. 6 to 57 percent; potash-clay brine slurry was consolidated from 3.8 to 35 percent; phosphatic clay waste from 15.6 to 49 percent; uranium tailings from 15.4 to 67 percent; tailings from talc production from 9.7 to 53 percent; and an acidic Ti02 slurr slurry from 1.68 to 30 percent.

Jan 1, 1980

By Jr. Koch

In the Hydrogeochemical and Stream Sediment Reconnaissance (HSSR) phase of its National Uranium Resource Evaluation (NURE) pro¬gram, the U.S. Department of Energy (DOE) samples about 1400 sites for stream sediments in each two-degree quadrangle of the National Topographic Nap Series (NTMS) and about 1200 sites for ground or stream water. Through a geological/statistical analysis, we find that NURE data are useful for assessing the uranium resources of the NTMS quadrangles. Our computer-implemented System for Uranium Resource Evaluation (SURE) calculates a score for each NTMS quadrangle based on the HSSR, geologic, and radiometric data; we score the four Colorado quadrangles--Pueblo, Montrose, Durango, and Trinidad--that comprise the study area. We interpret the scores in terms of geology and the known occurrences, which include the Hanson ore deposit with reserves of 30,000,000 lbs. U308 and the Pitch mine with reserves of 1,740,000 lbs. SURE depends in part on distinguishing mineralized or metalliferous granitoids from barren ones through "geochemical signatures."

Jan 1, 1980

By John Ward Smith

Dawsonite bearing oil shale of Colorado's Green River Formation offers a unique and vast (6.5 billion tons of Al2O3) resource of easily extractable alumina. The processing methods required by the thermal reactions dawsonite and its oil shale carrier also require production of shale oil, soda ash, and nahcolite as marketable coproducts. These production methods are presented. The alumina production process is contrasted with the Bayer process to describe technical advantages of extraction of alumina from oil shale which may offset the problems associated with processing a relatively lean ore. While alumina production from oil shale requires development of new technology, the technical problems appear solvable. Only the political problems arising from the now onerous and completely unnecessary Federal oil-shale withdrawal appear less solvable.

Jan 1, 1980

By H. R. Coles

Test work conducted in the 6.4 and 10.52 m Aerofall Mills at the Iron Ore Company of Canada Carol Project showed that the conventionally used ?deflector?-type liners which form the basic principle of Aerofall Mill grinding did not necessarily provide the best grinding performance. A new design, using low profile liners incorporating radial ribs of a proper height, actually improved the mill throughput in the order of 9 to 20% without sacrificing grinding efficiency. In addition, the new design reduced liner weight and scrap losses, which resulted in a reduction of liner consumption by 25%. It provided better protection to the mill shell and reduced the overall maintenance cost for the mill

Jan 1, 1980

By Robert A. Cummings

A field inventory was made of the mineral, geologic, geothermal, and groundwater resources of three geologically recent lava fields in the desert of Oregon. The term "resource" was applied with care: a "resource" must have particular value or worth, although it need not be economically viable. The spectacular volcanic features of the area have particular scientific and general interest and thus constitute geologic resources. The mineral endowment, mostly occurrences of low unit value such as stone and cinders, in large part are not resources, due to market conditions, regulations, and other factors. These and other conclusions will be used by the Bureau of Land Management in its multiple land use planning process for the area.

Jan 1, 1980

By S. D. Maksirnovic, Fred N. Kissell

The use of vertical surface degasification boreholes with bleeder systems and the use of a timbered bleeder system to degasify gob areas were studied by (the Bureau of Mines. This report describes three gob degasification studies ,conducted in the Pittsburgh coalbed. One study was conducted to determine the number of panels degasified with one large borehole . The study showed that the borehole provided degasification for three panels. Another study was conducted during the retreat of a 35-acre panel with a single-entry and a two-entry bleeder system and a large surface borehole. A major portion of methane emitted from the panel was carried away by the bore- hole, leaving the bleeder entries relatively free of methane. The last study was made to determine the effectiveness of a timbered bleeder system. The bleeder entries successfully degasified the gob area when enough entries were available and adequate pressure was available to force the air through roof falls.

Jan 1, 1980

By Anthony Edey, Leigh A. Readdy, Bruce A. Kennedy

Introduction Very little attention normally is given by the experts, or the public at large, to the fact that the majority of the oil that has been or will be discovered within the U.S. remains in the ground. The inherent limitations of oil production through surface wells, either by primary or secondary techniques, will result in a total of over 300 billion bbl of oil left in the ground after completing production by standard petroleum techniques in currently producing or producible fields. This reserve represents some two-thirds of the original quantity of oil discovered in place. Recent work by a number of groups has shown that there is strong economic justification for extracting this remaining oil by mining and processing techniques. Table 1, taken from 1977 API reports, demonstrates the oil left in place at the end of the conventional petroleum production cycle in then-known fields within th’e U.S. Possible targets for oil mining operations include (1) oil remaining in place in fields and pools that have reached economic depletion by current petroleum production methods and that are not amenable to economic recovery by conventional petroleum industry techniques; (2) oilor bitumen-saturated rocks not normally considered by the industry to constitute producible reservoirs, such as shales and diatomites; and (3) asphalt- and bitumen-impregnated rocks. Economically Depleted Fields A more detailed examination of the depleted fields shows that estimates of oil remaining in place after primary, secondary, and nondestructive tertiary recovery can vary widely. There is significant evidence, however, that more than half the estimated original oil in place (OOIP) remains in the reservoir after all petroleum extraction techniques have been applied. If one compares the sum of past oil production and estimated remaining producible reserves with the API estimate of total discovered OOIP as of 1975, it becomes apparent that for the U.S. as a whole, 67070of the 00IP will remain in place at the end of the

Jan 1, 1980

By Parris A. Lyew-Ayee

The Government or Jamaica has just completed agreements with four of the five bauxite/alumina companies operating in Jamaica. These companies are Kaiser, Reynolds, Alcoa, and Alcan, and the Agreements came into effect on February 1, 1980. One of the results of these new Agreements is the Acquisition of all company-owned bauxite lands by the Government and the rationalization of bauxite reserves.

Jan 1, 1980

By A. K. Kelly

Potash was first discovered in Saskatchewan in 1943 but its continuous extraction did not begin until 1962. In the years since then, potash has played an important role in the economic and political life of the province. And, as is well-known, the most eventful time in the life of the industry occurred in 1975 when the Government of Saskatchewan decided to become a major participant in potash production. To understand that decision, however, requires an understanding of the economic development of Saskatchewan and of relations between the industry and the government prior to 1975. This year, Saskatchewan celebrates its 75th year as a province. For most of those years, we have been an agrarian economy and society, dependent on exports of cereal grains, mostly wheat, for a livelihood. Even today, agriculture accounts for about 25% of the province's Gross Domestic Product (Economic Review, 1979, p. 7) and difficulties in agriculture spread rapidly to the rest of the provincial economy. The difficulties and risks that go hand in hand with being a "one crop" economy were known as long ago as 1920 but were not fully appreciated until the combination of depression and drought in the 1930's turned the prairie grain- belt into a dustbowl. Some idea of the severity of the depression is revealed by the following data: in 1928, Saskatchewan produced 321 million bushels of wheat. By 1931, the total fell to 132 million bushels and, in 1937, to a mere 37 million bushels. The value of agricultural products sold off farms fell from $273,000,000 in 1928 to a meagre $51,000,000 in 1937. The impact of such a fall of agricultural incomes was catastrophic since about 70% of the population of some 921,000 persons lived in rural, agriculture-dependent areas (Britnel.1, 1939, p. 14).

Jan 1, 1980

By Dan S. Nilsson

Small-scale mines are today expected to provide much of the increased production of metals, industnial minerals and coal this country demands in the future. But what is the size trend in the mining industry?

Jan 1, 1980

Properties of coal which are significant in relation to preparation for carbonization and conversion are reviewed, and existing coal preparation technology which has been used for production of cleaned coal of suitable ash content and petrographic composition for carbonisation, pyrolysis, hydrogenation and similar processes is described. Possibilities for application of this technology to some Australian coal seams is examined briefly. It is concluded that further survey work is required related to the optimization of selective crushing and concentrating operations, with the aim of maximizing production of quality products for carbonisation, etc mainly from Australian seams with only moderate coking characteristics.

Jan 1, 1980

By Thomas J. Kingston

A general overview of the taconite crushing process at Minntac is presented The process is controlled from a central control where the control room operator uses closed circuit TV, computer process control and alarms, graphic panels, and radio communication to roving attendants to run the Plant. This paper points out the operating controls and parameters as the plant operator sees and uses them.

Jan 1, 1980