Search Documents

By P J. Hommert, D S. Preece

"Commercial development of the United States Oil Shale reserve will require substantial amounts of mining. In fact, even a modest 500,000 barrels per day industry requires a mining effort equivalent to nearly half of the current U.S. coal mining industry. Obviously, mining efforts on this scale will benefit from technological advances. There are a number of areas where advanced technology could impact mining. These include continuous miners, shale transport systems, and blasting. This paperexamines recent developments in computer modeling of blasting and assesses the likelihood of these advances being applied to practical oil shale mining problems."

Jan 1, 1989

By Dean David

The evaluation of a new mineral sands prospect with unusual characteristics is described, The heavy minerals are very fine grained, have comparatively low average specific gravity (3.6) and are altered. Poor performance by conventional processing techniques made it necessary to trace the response of the major minerals during the separation processes, QEM*SEM® was used to quantify mineral volumetric abundances and mineral locking in magnetic and gravity separation products.

Jan 1, 1989

I was very interested in Professor Park's data on subsidence over longwall panels. His paragraph labeled "Conclusion," however, does not seem appropriate for the article. Nothing in the article gives any discussion of how knowledge of subsidence characteristics can be used in mine design to minimize damage. That thought may have been a reason for undertaking this study, but not a conclusion of it. From his article, I would conclude that subsidence movements last considerably longer at great depth. And the National Coal Board's subsidence prediction model represents this area reasonably accurately, though most literature claims their model predicts far greater disturbances than actually occur in most areas of the United States. Also, I would like to know, is the method used to determine angle of draw? The criterion used can make a significant difference in the value obtained. With 30 m (100 ft) spacing and a 122-m (400-ft) depth the angle between stations can be up to 14°.

Jan 1, 1989

By Egon Berger

"In recent years the trend in underground metal mining has been toward ever increasing blasts (often in excess of 100 000 tonnes per blast). The Canadian mining industry has been in the forefront of these developments (VRM, LBHand cable bolting to stabilize the surrounding rock /avoid dilution).In order to move these large tonnages, efficient loading systems have to be developed. This paper shows the technical and economic implications of various loading scenarios based on a predefined (however typical) stoping layout by:1 . discontinuous loading using scoop trams;2. discontinuous loading using scoop trams in combination with low profile dump trucks;3. continuous loading (based on loading performance/operating costs of the AL-60) in combination with low profile dumptrucks.The cost advantages of production concentration (loading large tonnages from one drawpoint}, made possible by continuous loading as opposed to sea tiered mining (small tonnages), using discontinuous loading in tunnelling will be presented, based on actual results obtained in a decline development project using the A L-60 continuous loader. At as pacing oj150m between turning bays, it was found that continuous loading was out performing discontinuous loading in approximately80% of the overall decline development.Fuel consumption and total cycle times are compared, and a cost assessment is presented.INTRODUCTIONThe subject of this paper deals with the introduction of continuous loading in underground metal mining and single heading tunnelingContinous mining has been widely introduced both in underground and surface coal mining. Mechanized longwall mining, utilizing moveable shield supports in combination with double drum- shearers, has resulted in a tremendous increase of coal production per working face.This has led to very concentrated mining operations. In a typical German coal mine two mechanized longwalls nowadays would produce the same amount of coal as 12 to 15 longwalls in the 1950s. One longwall in a South African coal mine has recently set a world record with 120 000 tonnes of coal in a single month.In underground metal mines-often due to the irregular nature of the ore body and the mining methods used-mining is far less concent rated. Ore is often produced from a large number of stopes and production sections. Sometimes, a substantial amount of ore may be obtained from development in the orebody (40070 at a German base metal mine)."

Jan 1, 1989

By Oleg N. Tikhonov

The paper deals with computerized analytical design of separational mineral processing flowsheets for flotation, gravity separation, magnetic separation, etc. (without comminution). Initial data include fractional composition of the feed ore, separational characteristics of the unit operations, and optimality criterion. Computer-calculated results display optimal flowsheet configuration and optimal parameters of unit operations like tonnage, residence time, etc., which allows the choice of equipment. An example of apatite flotation flowsheet design is given. This analytical approach may be used for automatic process control purposes as well.

Jan 1, 1989

By J. Peshel

This paper presents a regulatory perspective of the design and construction of the Exploratory Shaft Facility which may become part of the future high-level waste repository. Site characterization concerns and long-term waste isolation concerns require the consideration of various shaft design and construction aspects quite different from that of conventional shaft sinking.

Jan 1, 1989

By Ken Takahashi, Yuuich Umeki, Masahiko Arakawa, Dr. Tominaga. Yuusaku

Macroscopic characteristics of a complicated mine ventilation is remarked to build an expert system for mine safety in the Taiheiyo coal mine, Hokkaido, Japan. To gain the characteristics a large number of simulation were performed with varying aerodynamic resistance of the branches with regulator in mine ventilation network. The principal results of the study are as follows, (1) Pressure loss diagram for ventilation network with main and auxiliary fans enables capability of air circulation in the network. (2) H-Q (pressure-quantity) diagram gives capacity of air quantity In a network with main and auxiliary fans. (3) When airflow rate, [] through branch qi is changed by opening/closing regulator set in the branch, air flow rate, [], through branch p can be represented by the empirical formula. [ ] where Api and Qp,o are the constant coefficients. (4) Macroscopic characteristics mentioned above are available to make rules in an expert system for escaping route at emergency.

Jan 1, 1989

By Fred W. Stuart

Microprocessor technology has revolutionized the business community by placing tremendous computing power in the hands of the end-user for a very inexpensive price tag. The range of applications covers process control, to office automation, to personal computing capabilities. With the influx of this new technology, which these systems have to offer, also comes some unique operational and control considerations. But before we address these items, let us lay a foundation of common terms to be used throughout this presentation. Due to the rapid advances in microprocessor technology, where a new generation of computers is announced every two or three years, it becomes difficult to define a microprocessor system and have it valid for an extended period of time! Therefore, for this presentation, we will be dealing with a subset of microprocessors called Personal Computers or PC's. At the heart of a PC is a Central Processing Unit or CPU. The CPU performs the actual program and command execution. The programs dealing with driving the various peripheral equipment is referred to as the Operating System (for example: DOS : Disk Operating System, CP/M - Control Program/Microcomputers, etc.). The CPU is normally housed in an enclosure which contains power regulators, peripheral equipment interfacing 'cards', and expansion 'slots' to enlarge the capabilities of the PC system.

Jan 1, 1989

By J. M. Mutmansky, S. Padmanabhan

"The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Ucah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7.The results will be presented using two categories of data collected during two separate phases of the research:(l) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and(2) quartz concentration data from mines chosen at random.The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent."

Jan 1, 1989

By Y. C. Kim

Three rock fracture parameters define three points along empirical cumulative size (of rock fragments) distribution curves at Inspiration copper mine. These parameters are: rock quality designation (RQD), longest piece of intact rock and % of +1 inch. The RQD and the longest piece are actually measured on drill hole cores whereas % of +1 inch is visually estimated on the same cores. These size distribution curves are then utilized in a variety of engineering applications such as; slope instability analysis, blast design, copper recovery prediction from heap leaching, etc. The three rock fracture parameters for two dominant rock types (porphyry and schist) in the pit had to be estimated separately due to different rock fracture characteristics.' Both ordinary kriging (OK) with measured hard data only and soft kriging (SFTK) with hard and soft data were used to estimate each parameter. The cross validation of 100 measured sample values served as the-basis for evaluating the potential benefits of SFTK over OK. Use of subjective information during SFTK required obtaining (prior) probability distributions for all three rock fracture parameters. These distributions were obtained from the typical rock fracture parameters observed in drill hole cores falling inside the geologically interpreted structural domains with varying degrees. of fracture intensity and also through direct mapping along the exposed bench faces. Two different types of soft information were developed for this study; namely, Type "A" and Type "K". The former is based on sample distribution of fracture parameters whereas the latter is based on two step estimation designed to narrow the range of variation observed in data Type "A". The results of the cross validation were analyzed using a linear regression of actual values versus estimated values. The results confirm an improvement on the estimates made by SFTK with hard and. both types of soft data over those produced by OK with hard data only.

Jan 1, 1989

By Weir D. R, Doyle B. N

The Sherritt Zinc Pressure Leaching Process is based upon the direct pressure leaching of zinc sulphide or lead-zinc bulk sulphide concentrates to produce zinc sulphate in solution and elemental sulphur in the leach residues. The zinc sulphate solution is compatible with conventional purification and electrowinning technology. The pressure leach residues can be treated for the recovery of elemental sulphur, lead and silver. With the conversion of sulphur to the elemental form, zinc pressure leaching allows zinc winning to be independent of sulphuric acid production. Direct pressure leaching of zinc sulphide concentrates was started commercially in October 1980. Continuing research and development studies have defined various pressure leaching configurations for integration with existing roast-leach operations, for grass roots plants, or for plants which are to have the roast-leach section completely replaced. These studies have included the treatment of zinc concentrates from various Australian producers and the development of process flowsheets for potential applications in Australia.

Jan 1, 1989

By E. Bonates

Truck/shovel systems are a major form of materials handling in open-pit mines in spite of the high associated capital and operating costs. Mine management is usually faced with a decision to purchase new equipment in order to support the steadily increasing on production. These decisions involve a high degree of uncertainty with respect to future demands and technical developments. This paper describes a computer simulation model for evaluating the optimum equipment fleet in an open-pit mining operation. The system is based on a stochastic simulation program which accounts for the various mining and economic parameters. It calculates the type of equipment and the optimal number of trucks needed to meet the production targets. Two types of selection criteria: maximum rate of production or minimum cost can be applied.

Jan 1, 1989

By D. J. Dunn

Grinding balls, simple in shape, are actually sophisticated machine components, and essential elements of mineral grinding mills. Their physical properties and quality must be adequate to achieve design life and grinding mission with few failures. Consistant properties and freedom from breakage are essential. Size, mass, hardness profile, chemistry, and microstructure are important variables which should be designed, specified, controlled, and verified to achieve optimal mill performance. Failure to specify ball properties in detail or failure to obtain required ball properties and quality can cause milling productivity losses and excessive costs that could endanger a milling operations survival in the competive mineral industry.

Jan 1, 1989

By Jorj O. Osterberg

This paper is for presentation at the 14th Annual Members Conference of the Deep Foundations Institute held at the Hyatt Regency Hotel, Baltimore Maryland on October 10, 1989. This is an introductory presentation of a one hour symposium on the applications of a new testing device. This paper discusses how the device works and its uses. Papers following this describe: - How the cell is constructed and calibrated - Two projects on which the device was used on long driven piles to determine the frictional capacity - A bridge project on which the device was used on an instrumented test drilled shaft and a working drilled shaft

Jan 1, 1989

As an Inspector of Mines in Queensland, my main responsibilities include the enforcement of the Mining Act 1968 - 1986, the Mines Regulation Act 1964 - 1983 and the Metalliferous Mining regulations 1985 to promote the safe and responsible exploitation of the States' mineral wealth. An important adjunct to this task is the offering of an advisory service to the mining industry. However, in the pursuit of my duties to this regard, I have sadly observed in some cases, numerous wrong doings and negative activities by miners which have led to their ultimate demise, not to mention that of others. Despite what I consider corrective advice, I have witnessed, again in some cases, disregard and blind pursuit for the wrong end. This then is a novel approach to get the message home in the form of a light hearted cartoon presentation relating the saga of an average Aussie battler entering the mining game unprepared, making the wrong decisions due to his own ignorance and the cleverness of others, leading finally to his and possibly others' downfall. It is not intended to insult any particular profession or group of individuals and only endeavours to impart to readers and listeners, the message of being prepared and alert when entering the gold mining industry. Even though the presentation focuses on the woes of a rookie alluvial gold miner, a similar analogy could be drawn with his hard rock counterpart since the basic issues that I have attempted to address are common. By no means is there a saga complete because there are many more traps a miner can inadvertently fall into and only time has prevented me from referencing them.

Jan 1, 1989

By Betty L. Gibbs

The ultimate objective of mine design is to determine the development and untilization of mining resources. Computer Aided Design (CAD) and automated mapping are becoming very popular in engineering and in mining. Any computer program which produces a design or model with the interaction of an engineer can be considered computer-aided design (CAD), but' the term CAD is often associated with interactive graphic design and mapping capabilities. Graphics can be effectively used to describe and model two-or-three dimensional mine workings, orebodies, and geologic structures. Interactive computer graphics is applied to mine design with a combination of deposit modeling techniques and the use of AutoCAD for interactive graphics and mapping. The combined system can perform a large part of the calculations and drafting work for geologic and mining design. Using computer calculation and graphics techniques, comparisons of alternatives, can be made quickly.

Jan 1, 1989

By use of a finite-difference model of an experimental galvanic cell, the effect of a resistance in the metalic conduction path on the potential and current distributions in the cell was predicted. The model predictions were compared with experimental measurements of potential profiles (measured by use of a scanning reference electrode) and galvanic currents. The predictions agreed well with the experimental measurements. Apart from this model, which is applicable in macroscopic cells (Le. with an electrolyte of low conductivity), a calculation procedure was developed to predict the effect of an external resistance on the galvanic current in a microscopic cell (high conductivity). The responses of the galvanic currents in the microscopic and macroscopic cells to changes in the external resistance were compared. From the similarity of the responses, a simple practical procedure for the evaluation of the external resistance (meter resistance) that can be tolerated is proposed.

Jan 1, 1989

By Bruce H. Van Brunt, Danny L. Taylor

Estimation of local recovered tonnage and its grade above a cutoff is of paramount importance during the exploration and development stages of any mineral deposit. The spatial dis- tribution of grades as well as the cumulative distribution must be defined. In this paper, Probability Kriging, an estimator based upon rank order statistics and the estimation of the distribution of point grades within a panel, is applied to the Manhattan gold deposit. Mapping the conditional probabilities that estimated panel grades exceed a cutoff is useful to the understanding of the distribution of mineralization in a structurally controlled gold deposit.

Jan 1, 1989

By C. J. Gilbert

The mining method at the Cannon Mine uses heading and bench stopes, which are subsequently backfilled with cemented high-strength fill prior to pillar removal. The dimensions of the pillars, 24 feet wide by G5 to 95 feet high, re-quire careful blasting in order to not damage the rock, compromising pillar strength and complicating later removal. Additionally, the proximity of dwellings makes vibration control a must for good-neighbor relations. A blast monitoring study was conducted in order to optimize bench blasting practices to maximize fragmentation, reduce costs, minimize well damage, and minimize ground vibration.

Jan 1, 1989

By George H. Schnakenberg

Automation of coal mining activities at the face offers improvements in worker safety, health, and productivity. Introduction of integrated computer-sensor systems to current mining machines will enable these machines to perform some of the most hazardous tasks through supervised teleoperation. The U.S. Bureau of Mines is pursuing the development of the enabling technology necessary to achieve this goal. The research program consists of both basic and applied research, each focused on the fundamental issues of computer and sensor technologies. Short-term research is directed to providing computer-assisted, remote supervisory operation of present underground equipment; the long-term goal is the development of progressively more intelligent mining systems. The research program includes a review of robotic machine and autonomous vehicle technologies and of current mining technology, which provides a base for developing innovative mining methods; research in navigation and guidance technology, emphasizing control of a continuous mining machine; research on coal-rock interface sensing technology for horizon control, and rib thickness control in highwall mining; the development of computer systems and hierarchical architectures for real-time control; and development of expert systems for machine system fault diagnostics and predictive maintenance. This report presents a brief background and the current status for each of these research areas.

Jan 1, 1989