Search Documents

By John A. Kaufman, Terry D. Vandell

Recent mining regulations have increased the need for detailed engineering and environmental information pertaining to the hydrogeologic environment in mining areas. The cost of obtaining such hydrogeologic information has also increased. After mineralization of potentially economic grade ore and tonnage has been identified, and after completing preliminary mining feasibility studies (suggesting that development is merited), a second exploration phase can incorporate a simple, cost-effective baseline hydrogeologic data reconnaissance program that is limited but useful. Using exploration drill holes only, this program can provide a direct indication of where ground water is encountered. Also, reasonable estimates can be made on the relative production of water from various water-bearing strata, a composite potentiometric surface map can be prepared, and the general chemistry of the ground water can be characterized. This article outlines what typical baseline hydrogeologic data are needed and describes how it can be easily obtained during exploration drilling. Introduction Major engineering and environmental ground water parameters can be identified early in a project by using, drill hole data obtained from a mineral exploration program, designed by the mine geologist and hydrogeologist. Most importantly, data obtained in the exploration drilling program can be used to design a logical, defensible, and cost-effective baseline ground water data reconnaissance and monitor well program, which would be required for mine design and ultimately for mine permit approval. Drilling Where possible, exploration drill holes should be drilled with conventional rotary drilling equipment using air or, if necessary, water as the drilling fluid. Rotary air or water drilling generally allow good delineation of the first major saturated or water-bearing zone. If mud must be used during drilling, distinct hydrogeologic zones can still be defined, although the task may be considerably more difficult. Water Levels Static water levels can be obtained from selected exploration drill holes at specific depths while additional boreholes are drilled. Such measurements should not, however, be conducted until the hole has been developed with air (no water) and has stabilized at each of the depths to be measured. Such water-level information can be particularly useful when more than one aquifer exists. Where mine development is eminent, the hydrogeologist should install 50-100 mm (2-4 in.) diameter PVC casing in select drill holes. The PVC should be slotted, gravel packed, and properly sealed so additional hydrogeologic data can be collected for specific hydrogeologic zones at a later date. Such data could include water level information, permeability estimates based on injection and /or pumping tests, and water quality data. Where casing is not installed in drill holes, or when the drill holes are abandoned, the holes should be properly grouted and back-filled to the ground surface to prevent potential future ground water contamination. Monitoring Air Lift Water Production Estimates of the relative production from various water-bearing strata can be obtained from selected exploration drill holes. If ground water is encountered, its air lift (ground water flow) production can be measured at distinct intervals using a surface water flow measuring device, such as a portable Parshall

Jan 2, 1983

By S. D. Bechtel

Bechtel Civil and Minerals, Inc., one of the Bechtel group of companies, is a large engineering and construction firm that services the mining industry, among others. The firm's head, S. D. Bechtel Jr., comments on how his E&C company is dealing with the recessionary economy. First, he offered a historical perspective. About a half century ago-in the middle of the Great Depression-W. A. Bechtel and several business partners drew up a fixed price bid to build the Hoover Dam. At that moment in history, the W. A. Bechtel Co. was a modest success, but the times were troubled and uncertain. Money was scarce and a lot of contractors across the country were one project ahead of bankruptcy. The bid for Hoover was a make-or-break proposition for Bechtel, and it turned out successfully. The Hoover Dam was a no-frills operation in an isolated and harsh environment. There was plenty of hard work, long hours, and not many amenities. Controlling costs was critical. Everyone knew what had to be done, and why and what the consequences were. Today's Challenge Bechtel is now a bigger, more complex organization whose management views the current economic recession as a challenge to be met in much the same way W. A. Bechtel met the challenge of the Hoover Dam: by pulling together with a sense of purpose and direction. In many respects, Bechtel's situation today has a number of parallels to that which faced my grandfather. The company is eminently successful, but times are tough and there are plenty of signs that they could get tougher. My grandfather bet on the Hoover Dam to insure the future health of his company and I think we can work together again in that same tradition, make some tough decisions together, and the company's future can be just as promising. The first and most important requirement is to make certain that everyone understands the situation. The Bechtel group of companies are in an excellent financial position now. Its workload hit an alltime high in 1982 and it is well positioned in its principal markets. But the next two years may be critical for the company. Traditionally, Bechtel's work load lags behind general developments in the economy. Although many of its clients continue to suffer serious business difficulties, Bechtel is only beginning to feel the impact. The worldwide market for basic metals remains soft; relatively low prices and abundant supplies of oil and gas have flattened the petroleum market and made once promising synfuels projects economically unattractive; utility clients are still caught in the vise between overregulation and escalating costs. And persistently high, long-term interest rates have made capital investments expensive and difficult to justify. The company maintained a healthy workload through 1982. In some areas it has had little new work and consequently has been forced to lay off some staff as projects have been canceled or concluded. In other areas new work has tided the company over and more people have been hired. But new work bookings have fallen off, creating some uncertainty for the near future. 1983 requirements are clear, although seemingly contradictory. Belt tightening and cost reduction are necessary for Bechtel to remain healthy and competitive, enabling it to handle a possible further downturn with a minimum of turmoil and dislocation. At the same time, we need to allocate resources and funds in areas that will keep us positioned for the turn-around marketplace.

Jan 2, 1983

By Graham J. Morgan

The following material is excerpted from a presentation Mr. Morgan gave recently to representatives of the financial community. Introduction 1982 was a period of challenge for United States Gypsum Company because of reduced market opportunity. Housing starts for the first 10 months averaged a seasonally adjusted annual rate of 1 million units, 9% below the comparable 1981 period when housing starts were the lowest in 35 years. Industry gypsum board shipments declined 9% from the already low levels of the same period in 1981. US Gypsum met the challenge with stringent cost reduction programs and aggressive action in the marketplace. In late 1981, anticipating market deterioration, the company's management adopted strategies to focus on two shortterm objectives: • Adjust operations to perform profitably in view of limited opportunities through more efficient operations and asset management. • Continue to strengthen U.S.G.'s resources and ability to take advantage of important market opportunities as the economy improves through selective expansion of production capacity in key growth markets. Concentration on these two objectives resulted in a nine month performance in 1982 that, while certainly not satisfactory by company standards, compared very favorably with that of principal competitors in terms of net earnings, margin on sales, and return on average stockholders' equity. To counteract limited market opportunities, U.S.G. focused on productivity improvement, cost reduction, expense control, and maximization of market penetration. Energy Use Improving performance encompassed all segments of operations. For example, efficient use of energy was a significant factor despite lower operating rates at most plants. Overall, in the third quarter of 1982 versus 1972, the company used 27% less energy per unit of production, a savings of $15 million in that quarter alone. These continuing improvements helped to partially offset constantly rising energy costs. A number of operations achieved superior results in the first nine months of the year compared with the same period in 1981. For example, gypsum board plants in Jacksonville, FL, and Sweetwater, TX, recorded 8% and 7% reductions, respectively, in energy use per unit of production. Paper mills in Oakfield, NY, Galena Park, TX, and Kansas City, MO, each reduced energy use more than 12%, while the Greenville, MS, ceiling products facility achieved a 16%o reduction. Safety Safety is another important element that received increased attention. U.S.G.'s safety performance over the past five years has consistently improved. In 1981 it was five times better than that of the gypsum industry; nearly 10 times better than all industry as measured by the National Safety Council; and almost 20 times better than all US manufacturing as recorded by the Bureau of Labor Statistics. In addition to human concerns, this excellent record results in significant dollar savings that directly affect company results. In 1981, U.S.G.'s pre-tax savings in claims, premiums, and related expenses were about $20 million compared to the industries in which it competes. For the first half of 1982 performance improved further, with a cumulative lost workday incidence rate per 200,000 man-hours worked of only 0.27, an all-time record. Expense Control Careful control of inventories and receivables also received special attention. As of Sept. 30, 1982, inventories were 29%, or $44 million, below the level of Sept. 30,

Jan 2, 1983

By Frank Matter

Production of ultrafine powders of industrial minerals has been a problem in the past. In recent years new wet and dry grinding stirred ball mill systems have emerged which have been commercialized Two such systems are the TRZK mill with double step air classifier for dry grinding and the NRZK mill for wet grinding The primary features of these mills are feed entering from top and the product along with the grinding media leaving from the bottom, and a media separation and recycle system A detailed description of the NRZK mill for grinding coal is presented

Jan 1, 1983

By Jay P. Chapman

The basic control requirement for multi-pump, long distance slurry pipelines are discussed and a particular example of an operating slurry pipeline using programmable controllers is presented.

Jan 1, 1983

By Box JC

A comprehensive computer simulation has been developed for heap and dump leaching processes. It deals with complex chemical interactions, involving several minerals and reagents, which vary with time and location in the dump. The simulation is generally applic- able to ores of various metals extracted by different reagents. It requires only mineral- ogical data obtainable from drill cores and chemical data obtainable from the literature; there is no curve-fitting with adjustable parameters. Applications in designing testwork programmes, evaluating operating options, transferring experience to new situations and reducing uncertainty in long-term forecasts are described. Specific examples are included illustrating the potential of the simulation.

Jan 1, 1983

By Gill Montgomery

Although fluorspar is considered an industrial mineral by usage and value, its geological occurrence and the mining and milling methods employed make it more akin to the non-ferrous metal ores. Likewise methods of exploration for it are more like those used in the search for lead and zinc, with which fluorspar is often mixed. In fact, it often takes the mixture of fluorspar, lead, zinc, plus maybe barite to add up to enough recoverable values to make the mineral an ore by definition. This is so true where the fluorspar portion is low grade, perhaps less than 25 percent. Until the development of modern steel milling in World War I times, the invention of aluminum smelting, and development of the fluorine chemical industry and air conditioning, there were few uses for fluorspar aside from ceramic fluxes in the flint glass industry and for uses as glazes for pottery and china. Pure fluorite crystals have long been admired as semi-precious and ornamental minerals of many delicate colors.

Jan 1, 1983

By Michael S. Miller

During U.S. Bureau of mines mineral investigations, in 1981 and 1983, no mines, prospects, or mineral resources were identified in the Little Sand Spring Wilderness Study Area (WSA). Placer gold values in near-surface samples from alluvial fans within or near the WSA contained no more than 66 cents gold per cu yd, at $400 per troy ounce gold price. Sand and gravel and carbonate rocks occur in large quantities, but transportation costs to distant markets preclude their classification as resources. Nitrogen, lithium, clay, pumice, perlite, aragonite, and agate occurrences in the WSA are small or low-grade. The Silvia Mine, adjacent to the WSA contains gold-, silver-, copper-, and lead-bearing shear zones which strike toward the WSA. INTRODUCTION The Little Sand Spring WSA, encompassing 33,500 acres, is approximately 56 mi east of Big Pine, California, by paved and graded dirt roads (fl;. 1). Elevations range from 2,600 ft in Death Valley Wash to 5,600 ft along the California-Nevada boundary. The nearest permanent facilities are at Grapevine Ranger station and Scotty's Castle (Death Valley Ranch), about 9 and 11 mi, respectively, south in Death Valley National Monument.

Jan 1, 1983

Provide an effective method for "soft" soldering aluminum and aluminum alloys using conventional tin-lead solder alloys and flukes. The Problem In the past, it was virtually impossible to solder aluminum and aluminum alloys using standard tin-lead soldering systems (solder and flux) due to the presence of an aluminum oxide surface film which forms instantly on aluminum and aluminum alloys when these are exposed to air. The tenacious and stable oxide film enables aluminum-base materials to maintain their bright luster. But the film also prevents the required wetting and spreading of solder on the substrate, causing the loss of adhesion between the solder and the substrate. In addition, the heat produced during soldering increases

Jan 1, 1983

1. Journals Quarterly Journal of tke International Tin Research Institute, edited by Colin J. Evans and published by the Institute, Fraser Road, Greenford, Middlesex UB6, 7AQ, England. Engineering, building and construction law review, edited by P. C. Loots and published every two months by Construction Law Review (pty) Ltd (P.O. Box 78020, Sandton 2146, Transvaal), R63,00 per year. 2. Publications of the Mineral Policy Sector Nepkeline syenite and feldspar by B. W. Boyd Potask by G. S. Barry Selenium and tellurium by D. A. Cranstone Sodium sulphate by G. S. Barry Tungsten byG. G. Law-West 3. Mintek reports Report M114 Analytical methods associated with the recovery of uran~um. Report M117 An assessment of tke merits of various types of balls in tke milling of ores. Report MU1 Tke determinatl:on of trace elements in coal by atomic

Jan 1, 1983

By Pierre Antoine Dhaiti, Gilbert Sergerie, Michel Dagbert, Jean-Maurice Brodeur

"Quality of iron ore is generally determined by several factors which can be correlated or independent. Among these f actors, we generally find per cent iron, silica, magnetite or hardness. Forecasting the short- and long-term fluctuations of these f actors in the future pit is an important feature of mine planning in these deposits. Computer simulation provides a realistic answer to these questions. It allows to generate values for the most important quality features of each shovel load with the proper correlations between them as well as between one load and the next being fully reproduced. Then different sampling schemes f or grade control or blending facilities can be examined on the simulated data. The mechanics of the simulation procedure and its potential applications are described in an example.IntroductionThe purpose of this paper is to illustrate the use of in-situ grade simulation in the planning o f the grade control in an iron ore min e. More precisely, given a production unit of given size, we need to know how many samples have to be collected in that unit so that we ca n recognize its grade with a reasonable precision. Conclusions that we would like to arrive at are of the type: with 4 blasthole samples we ca n get the iron grade of a 10,000 ton bloc k with less than a ± 2% Fe error 95% of the time.The approach t hat we take to solve this problem is simulation. We simulate the grade of samples and the grade of the block that contains these samples. We repeat the simulation for hundred s o f blocks. By comparing the sample grade with the block grade in each case, we determine the actual number o f blocks where the difference sample-bloc k is less than a given limit."

Jan 1, 1983

By A. V. Z. Brink, D. M. O’Connor

Recent research into the prediction of mining-induced seismic events by the monitoring of small microseismic events at Western Deep levels Gold Mine is described. Measurement and interpretation techniques and results are presented. It was found that the occurrence of the larger events near longwall faces on the Carbon leader reef is preceded for some hours by an increased rate of microseismic emission and spatial concentration of the microseismic events in the zone of eventual failure. The research is currently being expanded with the aim of producing a practical rockburst early-warning system.

Jan 1, 1983

By George W. Toth

This paper describes the features of a computer cost model developed to estimate requirements and costs of individual coal mining projects. Detailed cost analysis procedures for both coal mining and preparation are incorporated into the model. This model has been developed over a period of seven years through funding provided by the Electric Power Research Institute (EPRI). The model follows a process engineering approach for the estimation of all project capital and operating costs. A discounted cash flow analysis procedure is also designed into the model to allow for the solution of cost/ton or cost/MMBtu of clean coal production. The model can be applied to most surface or underground mining deposits and can accommodate a wide variety of coal washing situations. This flexibility makes the model a particularly useful tool for preliminary project analysis, property screening, investment analysis, mining technology assessment, coal cleaning level assessment, and general property valuation.

Jan 1, 1983

By Alan Reed

"Afton Mines Ltd. (N.P.L.) operates an 8500-tpd open-pit copper-gold mine near Kamloops, R.C. The pit is currently 480 feet deep and will reach an ultimate depth of 800 feet. The east, south and west walls of the pit are composed of Triassic andesites (Nicola Volcanic Formation) and contemporaneous sub-volcanic intrusions of micro-syenite, microdiorite, diorite and picrite-basalt (Iron Mask Pluton). The north wall of the pit consists of Tertiary sandstones, shales and mudstones (Tranquille formation) and dacitic dykes, sills, flows and tuff s (Kamloops Volcanic Formation).The Afton copper-gold orebody (30 million tons of open-pit ore with a grade of 1.0 per cent copper, 0.016 oz/ton gold and 0.12 oz/ton silver) occurs within the Triassic Iron Mask Pluton adjacent to its faulted contact with Tertiary rocks. The Triassic-Tertiary contact is a complex fault system dipping 65 degrees southward and causing the Triassic rocks to overlie the Tertiary rocks. The detailed trace of this contact is very intricate due to the mutual interference of three principal fault systems.The dominant geological structures in both Triassic and Tertiary rocks are faults striking WNW and dipping 65 degrees southward, i.e. sub-parallel to the orebody (strike faults). Cross faults and oblique faults are abundant and highly significant in some sectors of the pit. The Tertiary sedimentary rocks show an early series of northwesterly plunging folds deformed by a later series of northeasterly striking folds. Major lithological and structural boundaries divide the pit into 8 structural domain s within which the pitwall slope stability is controlled by the local geological structures and lithology.Assay data from production blasthole samples and exploration diamond drillhole samples show a log-normal frequency distribution, with a fairly low relative variance. Variograms computed from production blasthole samples show good continuity with elliptical horizontal zones of influence which are truncated by the major faults that bound the ore zone."

Jan 1, 1983

By Krishna P. Sinha

An investigation was made to determine the creep behavior of oil shale at elevated temperatures. During the first phase of the investigation, work done on creep behavior of geologic materials was reviewed and triaxial creep tests on oil shale were planned. Tests at temperatures up to 250°C and axial stress up to 3000 psi were conducted at no confinement and at confining pressures equal to 1/3 and 2/3 of axial stress. Wide variations in the elastic properties as well as creep characteristics are exhibited. Creep deformation is more pronounced at elevated temperature but no definite quantitative remarks can be made regarding effect of grade of oil shale due to wide scatter and limited number of data paints. Primary creep can be described by a power law. Secondary creep seems to be an experimental function of deviatoric stress. Teritary creep was not observed within the test duration (24 hours in most tests).

Jan 1, 1983

By P. R. Sheorey

Understanding of in situ rock mass behaviour has taken a step forward with the advent of the refined rock mass classifications of Wickham, Bieniawski and Barton et al. In this paper six case studies are given in brief showing how Barton's classification could be used in mining situations. The cases cover stability of roadway junctions under shallow covers, support pressure estimation in roadways in intact and failed rock conditions, determination of the safe unsupported span of a wide stope and estimating the stability of roadways in two contiguous seams standing 011 small pillars against puncture of the parting rock.

Jan 1, 1983

By Harry Sutcliffe, Francis M. Keville

The paper describes the, impact of the geotechnical exploration program on the line and grade of the tunnels and the shaft configuration on the Red Line Extension N.W. in Cambridge and Somerville, Massachusetts, and comments on several aspects of the implementation of the project.

Jan 1, 1983

By H. N. Mills

The glass industry is a major user of many industrial minerals in the manufacture of its product. It is the intent of this chapter to: (1) acquaint the reader with the glass industry by including a few production statistics, and (2) cover the various aspects of the major raw materials used to make glass. The matter of glass compositions, properties, and batches is considered beyond the scope of this chapter which deals only with raw materials. For more details on the particular minerals and rocks used in glassmaking, the reader is referred to chapters in the commodity section of this book. Glass Industry Statistics Glass manufacture in the United States can be divided into three major product classifications as follows: 1) Glass containers 2) Pressed and blown glass 3) Flat glass Glass containers include bottles and jars for the packaging of food and beverages, as well as drugs, chemicals, and cosmetics. Pressed and blown glass includes table, kitchen, art and novelty ware, lighting and electronic glassware, and fiber glass. Flat glass covers sheet or window glass, plate, laminated, and safety glass. The US Department of Commerce statistics, as recorded in the 1977 Census of Manufacturers, compares the dollar value of glass shipments for each product category. These statistics are shown in Table 1 (Anon., 1980) and are self-explanatory. A comparison of the tonnage output in each product classification is difficult, as production data is reported in "gross" for glass containers, "pounds" for fiber glass, "pieces" for glassware, [ ] and "square feet" for flat glass. In the case of glass containers, an average "pounds per gross" factor can be applied to the total production figures reported in thousands of gross in Bureau of Census industrial reports. Table 2 presents the calculated annual production tonnage for glass containers for the years 1974-1979. Except for 1979, there was a yearly increase in production. The tonnage figures of Table 2 are further influenced by decreasing weight per gross which has occurred in the glass container industry since 1975. This reflects the gradual shift to lighter weight containers for beverages. Other segments of the glass industry have experienced growth, but the figures in tons are not published information. Fiber glass growth has been influenced by the heavy demand for insulation as part of energy conservation efforts on a national basis. The production of flat glass by the float process has continued to grow with several new plants entering production. All portions of the glass industry experienced the effects of the general economic decline of 1979-1980, but the outlook for the future is bright. Batch Materials For Glass Use Materials and Function Soda-lime-silica glass represents the largest proportion of glass manufactured for commercial use. It is produced by the fluxing and

Jan 1, 1983

By Sidney M. Cohen

This paper describes an economical method of upgrading a clay deposit using conventional separation processes into a suitable cement plant feed. The natural size difference of clay and silica in the clay deposit is utilized in the dry air classification device. A case study in which the raw material from a clay deposit is converted into a portland cement plant feed is presented.

Jan 1, 1983

By Alex G. Sciulli

According to recent estimates, nearly 30 percent of the material from underground coal mining in the United States is rejected on the surface as waste. This accumulation of almost three billion tons of coarse and fine coal refuse is primarily from coal cleaning operations. The marketable coal is intermixed with sandstone, clays, shales, and carbonaceous rocks, which must be removed and disposed of in an acceptable manner. The disposal of mineral wastes is a major environmental concern. The most common types of environmental problems associated with coal refuse disposal are acid formation, erosion, and sediment control. Other areas of concern include air and water quality, combustion control, mine sealing, and reclamation. This paper focuses on these topics and attempts to outline special environmental features which can be incorporated into the design and construction of a coal refuse facility. Often these measures can minimize and possibly eliminate the potential environ- mental hazards. It is imperative, however, that these measures be adopted prior to and during construction, because of the relative ease and cost savings compared to post-construction implementation.

Jan 1, 1983