Search Documents

By Harold Stocker

INTRODUCTION This presentation is concerned with the administrative and technical capability of the Atomic Energy Control Board (AECB) to assure compliance with the individual exposure limit for radon daughters (currently 4 WLM per year). It is not concerned with the epidemiological bases for setting the exposure limit. Moreover, the intent is to show how sophisticated methodologies and advanced technologies, applied to radon daughter concentration measurements in uranium mines, convey the spirit of compliance by providing better estimates than do the historical methods. These better estimates mean that more accurate and more precise estimates of each worker's exposure are determined using these more modern methods and devices. The estimates so derived should provide more convincing evidence to an individual worker that his assigned exposure is a valid indicator of his true exposure. In addition, a perspective on the exposure estimate in relation to the exposure limit is given as further evidence that an exposure limit is not the dividing line between "safe" and "unsafe" exposures. A brief description is given of the compliance aspects of the Atomic Energy Control Regulations and of the limitations of purely statistical non-compliance procedures. Most of the emphasis of the paper will be placed on the uncertainties associated with conventional radon daughter exposure determination and the means being employed (and anticipated) to reduce these uncertainties. NON-COMPLIANCE Under current Atomic Energy Control Regulations (1978), the annual individual exposure limit for radon daughters is given without reference to the possible methods of sampling and calculation of radon daughter exposure and without any reference to possible uncertainties or their magnitudes. This is common in such statutes, the details of sampling, calculation, error analysis, and so on, being left for licence conditions or provided as a specific guideline to the licensee on the matter of compliance with the Regulation. Since the exposure limit is contained in the Regulations, compliance with it is absolute, as with any other law. In Canada, a state of non-compliance with the radon daughter exposure limit exists when an exposure (attributed to an employee) is reported by the licensee to exceed the limit. No uncertainty in the measurements or in the overall determination of exposure is reported nor is any requested. Removal of the worker and the loss of his services are the immediate and direct penalty suffered by the licensee for failure to maintain the exposure at, or below, the limit. A worker may be re-instated to employment for the balance of the reporting period only if the licensee can assure the AECB that further significant exposure to the worker will not ensue. In other jurisdictions, such as the United States, non-compliance is defined on a statistical basis. For example, NIOSH, the National Institute for Occupational Safety and Health presents procedures for calculating the 95% Lower Confidence Limit (LCL) in order to "compare the results of occupational environmental sampling to an occupational health standard and make a decision with a known chance of making an incorrect decision that a state of non-compliance exists" (Leidel and Busch, 1975). (In the nomenclature of this presentation, exposure limit would be used in place of "standard", in the NIOSH sense). Furthermore, it is emphasized in the NIOSH document that such numerical comparisons "are necessary only if the sample mean is greater than the standard". The NIOSH document points out, quite correctly, that the "statistical procedures presented below will not detect and do not allow for analysis of highly inaccurate results, i.e., systematic (non-random) errors or mistakes ... If a systematic error is known to exist in an instrument or analytical procedure then correct the sample mean of the data before analyzing for non-compliance". It is certainly not the purpose of this paper to criticize the sophisticated statistical approach to non-compliance as given in the NIOSH document or in similar approaches used in other jurisdictions. Rather, the purpose is to approach, with some introspection, the question of the determination of exposure by the employer for his employee and especially the employee's understanding of, and confidence in, the accuracy of the exposure determination and its relation to the exposure limit. DETERMINATION OF EXPOSURE Historically, in uranium mines, exposure to radon daughters for an individual miner

Jan 1, 1981

By I. A. Goddard

INTRODUCTION This paper deals with the development of the sublevel open stoping (SLOS) method in lead orebodies at the Isa Mine of Mount Isa Mines Limited, during the last ten years. Open stoping in different forms has been used at the Isa Mine for many years. Prior to the period under review, stopes were small, pillars were not always recovered, and scrapers extracted the ore. By the end of the sixties, the use of load-haul-dump units was becoming more widespread. Wagner ST5's were the mucking units for the lead cut and fill stopes. Some of the open stopes in 5 orebody above 13 level had 100 kW slushers, but the more southerly stopes were the sites for the introduction of diesel front-end loaders for extraction. In the early seventies, new methods were used in the block of six stopes in 2 and 5 orebodies between 8 level and 13 level and a trial stoping project was undertaken in 7 orebody between 11 level and 13 level to determine possible stope dimensions for the extraction of the Racecourse orebodies below 13 level. By the mid-19701s, stoping was well underway in 5, 7 and 8 orebodies between 13 level and 15 level, using the 'triplet' system, incorporating cemented hydraulic fill to allow greater pillar recovery. As the eighties were entered, development of the Racecourse orebodies below 15 level commenced, as did preparations for 1 orebody in the upper levels of the north end of the mine. In both cases, the pillar recovery method has been changed to reduce the amount of cemented fill required for pillar recovery. GEOLOGY Most of the lead orebodies at Isa Mine lie chiefly to the north of the central shaft complex. They are bedded sulphide deposits in a host rock called Urquhart Shale, which dips at roughly 650 to the west. The main minerals are galena and sphalerite, with the silver mineral, freibergite, being contained in the galena. To the hangingwall of the sequence are the Black Star orebodies (1, 2 and 5) which are relatively wide, pyritic and with low to above average grade lead. The Racecourse orebodies (6 to 16) lie to the footwall, and have a large variation in width, low to high grade lead, and gradation in the lead to zinc ratio from north to south. Stope outlines are often determined by economic or engineering considerations rather than geological. The published extraction reserves are 56 million tonnes of primary ore, containing 150 grams of silver per tonne, 6.4% lead and 6.5% zinc. Traditionally, it has been regarded as lead ore, although the dominant revenue earner varies from time to time. In the Black Star orebodies, the ore and hangingwalls are more competent and open stoping has long been used. The major Racecourse orebodies which have been open stoped are 7 and 8 orebodies. This has been where the orebodies are wider (to the south) and where hangingwall conditions allow. This latter aspect has been greatly influenced by the presence of 'silica dolomite1. This tough, relatively homogeneous, non-bedded rock is, in fact, the host rock for the copper mineralisation at Mount Isa, and provides a competent hangingwall for some of the lead stopes. While the shale's bedding and jointing has a major influence on the ground conditions, there is a major fault system which causes local problems. The principal virgin stress direction is perpendicular to the bedding, but the local stress situation is complicated because of shielding by filled stopes in the hangingwall copper orebodies and because of the interaction between orebodies being extracted to the footwall. Most development on strike is mined with a 'shanty-back’, with the back being as close to normal to the bedding as possible. This is near parallel to most jointing and the principal stress direction. Figure 1 is a plan view of 14 level north, which provides a representative horizontal section through the orebodies. A typical cross section is shown in Figure 2. The narrow, parallel footwall orebodies can be seen to differ from the wider hangingwall orebodies.

Jan 1, 1981

By R. W. D. Clarke, J. C. Folinsbee

INTRODUCTION This paper deals with a procedure for planning the mining of an orebody for which cross-sections, plans, grade of ore, and a geological estimate of the ore reserve have been prepared. The procedure begins with the preliminary selection of a mining method or methods on which an engineering evaluation will be carried out. The engineering evaluation is described in three parts: Conceptual Studies Engineering Studies Detailed Design An overall planning model is presented, plus an expanded model for the Engineering Study Throughout the discussion of the planning procedure, reference is made to three bulk mining methods, including block caving, sublevel caving, and longhole sublevel stoping, including a summary of the main characteristics of each of these mining methods. The planning model is designed for a longhole sublevel stoping method, but with modification, will apply to other methods. PRELIMINARY SELECTION OF A MINING METHOD To experienced mining engineers, identification of the nominal mining method for a given orebody normally involves a large measure of judgement. The geological data is reviewed to determine the configuration of the orebody, including size, shape, dip, grade, and metal distribution. Geotechnical data is considered, including the competence of the ore and host rock, faults, fracture patterns, groundwater, and the potential for in situ stresses. Geographical data, including the natural and societal conditions, are evaluated for their effect upon the mining method, and finally, economic data, basically defined as the value of the ore in the ground, but more specifically, including grade of mineable ore, distribution of ore grade throughout the orebody, and metallurgical recovery, will have a bearing on the nominal method selected. Preliminary evaluation of these factors will result in the elimination of the obviously inappropriate mining methods, leaving some method or methods for further, more detailed study. Since ore does not occur in simple geometric shapes, the method selected for more detailed study will require some variation to the standard. A few key factors will bear heavily on the selection and provide a basis for the most realistic choice. Geological Data The configuration of an orebody defined by the horizontal and vertical dimensions, the dip and strike, and the possibility of repetitive occurrences will have the major influence on the selection of the mining method. For bulk mining methods, the dip of the orebody should be steep, or the orebody must be thick so that gravity can be utilized to deliver fragmented ore to a central gathering area. Geotechnical Data The geotechnical data will be studied in greater detail when the nominal mining method has been selected and the engineering evaluation is undertaken. However, some basic initial information must be available. The structural strength of the ore and host rock, including the effect on it of faulting, fracturing, and insitu stresses, must be known. Data from exploration drilling and examination of drill core will assist in the preliminary assessment of these factors. Highly fractured ground may suggest a caving method of mining for certain orebody configurations, whereas highly competent or strong ore might indicate that for a similar configuration, longhole sublevel stoping will more likely succeed. Data obtained on groundwater from exploration drilling will be considered to determine if it can be controlled, or if it will represent a long term major expense or a hazard for which no control is possible.

Jan 1, 1981

By Maurice Lacasse, Pierre Legast

GENERAL OUTLINE For more than one hundred years, asbestos ore has been mined on Les Mines d’Amiante Bell's property at Thetford-Mines , Quebec, Canada. In 1878, the first tons of fibre were produced. The mine operated as an open pit until 1951 at a yearly production of about 330 000 mt of ore. Since 1951, the mine has operated underground using a block caving method. The mine produced 725 000 mt per year until 1978, when the rate of production was increased to 1 100 000 mt. The ore was produced entirely fm the first lift on 650 level until 1976. Then, a second lift on 950 level was put into operation to replace production facilities fm the first lift which is now exhausted. Annual fibre production is 72 500 mt with grades £ran 3 to 7. The total work force is 600 people. The host rock is a peridotite partially serpentinized. The asbestos fibre seams occur as stockwork deposit structurally controlled by talcose shear zone. The geological rock formations are heavily jointed and have a wide range of competence. Asbestos ore bodies have an heterogeneous nature which des difficult geological interpretation. THE GRIZZLY METHODS A full gravity method was used on the first level where the caved ore was drawn from finger raises onto grizzly bars spaced at 480 mn. Oversize blocks were reduced by secondary blasting. The ore fell by gravity in- to the ore pass below the grizzly chamber and was loaded into 5.7 mt haulage cars through a 1.2 m wide chute. Access to the undercut drift was fm the grizzly drift through finger raises. The undercut trough was drilled and blasted in a 1.2 m interval ring sequence into a slot situated at the end of each panel. The undercut stope was emptied through the finger raises. The undercut retreated from South to North at blast interval determined by the finger raises spacing. Fig. 1 represents the various steps involved with the grizzly method. Extraction drift dimensions were opened 1.8 m wide x 2.4 m high with anchor rock bolts and wire mesh where safety required them during excavation. Grizzly chambers were excavated at 2.4 x 2.4 x 4.6 m long on a 7.6 x 7.6 m grid spacing. Ore passes with dimensions of 1.5 x 1.5 m were developed from the haulage drift. On the extraction level, headings were drilled with jacklegs and cleaned by slusher into ore passes to the haulage chutes. The support used in the grizzly chambers was square concrete structure with 150 mn H beam reinforcement. The H beam was partially buried in the concrete and had one free face to allow for difference frequency of blast vibration between concrete and steel. The supported brow of the chamber had an opening 1.5 x 2.1 m. Ore passes were ring concreted 150 mn thick without any reinforcement. A 24 MPa compressive strength concrete was pumped and poured in pre-assembled forms. Based on the success of this method on the first level, the same layout was repeated on the second level. With the start of undercutting on the second lift, signs of deterioration were noticed in extraction drifts. At first, there was great concern as the operators were confident that standard repair techniques could cope with such a situation. An intensive program of support repair and a reduction of draw resulted. The following method of repairs were used: 1) Steel square sets of 150 mn H beam at 0.6 m intervals were installed. 2) This was reduced later to 0.3 m interval and eventually to a skin to skin steel structure. 3) Yieldable arches were introduced spaced at 0.9 m intervals, linked laterally with 150 m. H beam. 4) The yieldable arches spacing was then reduced to 0.46 m and eventually installed skin to skin. However, this support was not successful.

Jan 1, 1981

By M. H. Pettibone

During the past decade, the size of grin- ding mills has steadily increased. Mills 11 m in diameter with 9 mW motors have been installed with even larger units on the drawing board. The rising costs of energy and labor have spurred interest in improving efficiency while reducing capital investment and operating labor. Autogenous and semiautogenous grinding have experienced renewed interest as efforts to reduce operating and capital costs have increased.

Jan 1, 1981

By Robert C. Paddock

INTRODUCTION A way of producing 3,000 tpd from the El Mochito Mine was needed. Of this production, 2,000 tpd must come from the San Juan orebody. The original sub-level stoping method did not give satisfactory results due to ground instability, and the highly irregular ore/waste contacts encountered . The experience gained from the initial system helped guide research into the ground instability problem. Results from this work, combined with knowledge gained about the orebcdy configuration, defined constraints that were previously not fully appreciated. These constraints, and others, combined with objectives, were considered together to develop a new mining method. No single technique was found to be suitable, so a hybrid mining system was developed. A combination of ramping, cut and fill, and vertical crater retreat, with an option to use top heading and benching was developed. To complement the mining system, the type of equipment needed was decided upoun. Also, to support the mining system at this expanded rate of product ion, major modifications of existing infrastructure were required. THE EL MOCHITO MINE The El Mochito Mine, of Rosario Resources Corporation, has been in continuous product ion since 198. The mine began operations in April of that yeas at a rate of 100 tpd. The reserves in 198 were 100,000 tons of silver ore assayed at 1,250 grams per tonne. As of the end of 1979, the El Mochito orebodies have produced over 5.6 million tonnes of ore averaging 516 grams per tonne silver, 6.8 lead, and 7.8% zinc. Present ore reserves are about 7.9 million tonnes, averaging 138 grams per tonne silver, 4.6% lead, and 8.7% zinc, with minor quantities of copper, cadmium and gold. An expansion plan to increase mill production two fold to 2,500 tonnes per day is underway. This expansion will require the mine to produce 3,000 tpd. The mine consists of numerous orebodies, all of which have been mined to a certain extent. Of all the orebodies, the San Juan contains 8% of known reserves. This amounts to about 6.7 million tonnes. The significance of the San Juan orebody to the future life of the El Mochito Mine is obvious. If the required mine production of 3,000 tpd is to be sustained, the San Juan must be the source of the majority of that production. Due to the mineability and overall logistics concerned with the other orebodies, the San Juan must be able to reach and maintain a production rate of 2,000 tpd by 1982. GEOLOGY OF THE SAN JUAN OREBODY The El Mochito Mine is a classic example of a chimney replacement deposit in limestone. Similar deposits axe found in Mexico, at the Naica, Providencia, and Santa Eulia Mines. The El Mochito Mine is located at the south- western end of the Sula Valley on the western edge of the Honduras Depression in the Central Cordillera and Central Highlands of Honduras in a setting of Mesozoic sediments. The orebodies occur in a structural basin developed between NNE trending normal faults and apparently hinged on the south end. Topographically, the Mochito Basin lies between the uplifted Santa Barbara mountain in the west and the Palmer Ridge on the east. The San Juan orebody occurs near the intersection of the NE trending San Juan fault and the ENE trending Porvenir fault. The downward continuation of the orebody is controlled by the westward rake of these NW and N dipping structures. The discovery of the San Juan orebody is attributed to analysis of structural evidence of known ore deposits by in-company geologists. The composition of the San Juan orebody is primarily garnet skarn, with local concentrations of hedenbergite and magnetite. The economically important sulfide mineralization consists of (in decreasing abundance), sphalerite , galena, pyrrhotite , and chalcopyrite. There is some indication that a Cu-Ag mineral such as tetrahedrite may also be present. The skarns were formed by replacement of the original limestone by hydrothermal water migrating upward roughly along the intersection between the Porvenir fault system and the San Juan fault system. Textural evidence suggests that the orebody is a composite of several pulses of hydrothermal activity which would explain, in pat, the great irregularity of the contacts and the large horizontal variation in mineralogy. A general pattern of skarn types can be seen in the orebody, partially accounting for the observed lateral variation in grades. This zonation is very generalized, and one or more zones may be missing in any given locality. The orebody is almost invaxiably surrounded by a 2 cm to 25 cm zone of bustamite skaxn with low values. The border skarn is usually

Jan 1, 1981

By Jack Bradbury

The open stope room and pillar method of mining is used throughout Ozark Lead Company's underground mine located at Sweetwater, Missouri. This method of mining produces an approximate overall ore extraction of 80%. Pillar recovery, on a limited and experimental basis, was started in January of 1979 to determine the maximum size underground opening that could be mined safely. Monitoring the roof and surrounding pillars for potential failure during this pillar recovery process was accomplished by utilizing a simple rod extensometer to measure roof sag. Boreholes 7.5cm in diameter were drilled 3.5m into the roof to spot any separations or cracks that might have propagated between the bedded layers of rock. Underground openings 85m in length by 46m in width have been mined successfully without roof or surrounding pillar failure. Continued measurements to establish long term results will be necessary.

Jan 1, 1981

Previous methods for the assessment of the explosive potential of gas mixtures have required the plotting of apeexplosibility diagram. These became cumbersome if a large -number of assessments of various sampling locations over a period of time wererequired. This may make the approach of a dangerous situation more difficult to predict. With the aid of a programmable calculator, a new method for the rapid assessment of the explosibility of coal mine sample gases has been developed. This method does not require that an explosibility diagram be drawn to indicate the explosive status of a gas mixture. Simple Cartesian co-ordinates representing the explosive potential of,mixtures are obtained, which may readily be plotted to show changes with time.

Jan 1, 1981

By Wils L. Cooley

This report analyzes electrical accident data in the metal/non-metal mining industry. Accidents are categorized to determine their root causes. Special attention is given to accidents associated with inadequate or defective grounding of mine power systems. Recommendations are made concerning proper grounding practice, especially for dredges and for quarries in hard rock or sand. The costs of instituting the recommended practices are estimated for model mine power systems which are based on field data obtained from 37 mines and several electrical contractors. The expected benefits of various suggested safety practices are also estimated.

Jan 1, 1981

By R. N. Hambright

Gaseous and particulate exhaust emissions are characterized for a 1200 Bhp two-stroke cycle diesel, a 1000 Bhp four-stroke cycle pre-combustion chamber diesel, and a 900 Blip four-stroke cycle, direct injection diesel using steady-state modal testing and a versatile exhaust dilution-collection system. In addition, a 1.50 Bhp four-stroke cycle, pre-combustion chamber, turbocharged diesel was characterized for use in experimental water injection evaluations. Water injection downstream of the turbocharger compressor and upstream of the turbocharger exhaust turbine are evaluated for their particulate removal effectiveness on the small turbocharged diesel engine. The water droplets are inertially separated using cyclone separators designed for minimum pressure drop and outsize, lip to 50 percent of the total particulate mass generated was removed using a combination of both inlet and exhaust water injection techniques.

Jan 1, 1981

By John W. Tieman

Coal is a term applied to vegetable matter (trees, grasses, etc.) which was subjected to heat and pressure through geologic ages. This resulted in a change in both the physical and chemical properties. Because its chemical composition is variable, geologists classify coal as a heterogeneous mineral rather than a homogeneous mineral. Peat represents the initial, unconsolidated stage in the development of coal. This coalification continues with time and the application of temperature and pressure to lignite, subbituminous, bituminous, and anthracite toward the theoretical graphite end member. PHYSICAL PROPERTIES OF COAL The physical properties are concerned with the characteristics of coal in its natural state, or prior to its end use as a fuel. For example, the hardness and grindability of coal determine the maintenance cost for coal mining, handling, and pulverizing equipment; the specific gravity of coal and its associated minerals determines the coal preparation technique used in a cleaning plant as well as the capacity of coal bins, boats and size of cargo, and other coal storage facilities. The physical properties are, of course, dependent on the chemical constituents of coal, and all properties are interrelated. Specific Gravity The specific gravity (sp gr) of a solid is the ratio of the weight of a cubic foot of the solid to the weight of a cubic foot of water. The specific gravity of pure coal has been reported to range between 1.23 to 1.72 and increases with the change in rank from lignite to anthracite. This means that it is 1.23 to 1.72 times heavier than water.

Jan 1, 1981

By J. A. Botin, K. H. Singh

INTRODUCTION The Alfredo underground mine is one of the three mining operations of Rio Tinto Minera, S.A., all near the community of Rio Tinto in Huelva province of southwest Spain. The other two operations are Corta Atalaya open pit (Pyrite ore) and Cerro Colorado open pit (Copper ore 1. Underground mining of Alfredo Mine for pyrites started in the nineteenth century and continued without interruption until 1979 when it was discontinued due to economical reasons. In 1972, a new project was started for the mining of copper bearing ores on the footwall of the pyrite deposit. This copper ore is locally named “Cloritas” and it forms a nearly vertical and tabular shaped orebody which forms an envelope at the footwall of the San Dionisio pyrite orebody. Mining of the Cloritas commenced in 1975 using cut and fill stoping. In 1977, the original project was completely revised which led to the introduction of a bulk mining system to achieve a planned production of 3,000 tonnes of ore per day. This paper covers the economic and planning aspects of the mine and discusses the evolution of the mining method for the Cloritas orebody. A GENERAL DESCRIPTION OF THE CLORITAS OREBODY The “Masa San Dionisio” (figure 1 ) is a massive sulphide orebody located in the town of Rio Tinto, about 90 kilometres west of Sevilla, Spain. Extensive vein-type sulphide mineralization exists in the volcanic host rocks of the Masa San Dionisio. Within this area of stockwork veins, there is a higher concentration of copper in the form of chalcopyrite in a zone adjacent to and paralleling the contact with the massive sulphides. This copper envelope is locally referred to as the "Cloritas Orebody” and the ore within it is called "Cloritas”. The main zone of the Cloritas orebody, (figure 11, is tabular and nearly vertical having a length of 375-400 m east-west, a thickness of 20-50 m north-south, and a vertical extension of 500 m from the surface. In addition to this area, there is a second less important low grade area called zone 2A located to the north of the main zone below 26 Level which, in some sections, is not fully separated from the main zone. MINING METHODS Mining in Rio Tinto area can be traced back to the Phoenecians and the Romans. Modern day mining started with the demand for sulphuric acid during the last half of the nineteenth century. By 1971, more than 33 million tonnes of pyrite had been mined out of Alfredo Mine, (San Dionisio Orebody), using labor intensive drift and fill methods and also by open pit method. During the last decade, underground mining of the pyrite had become uneconomic due to lower prices and a slackening demand for pyrite, and the underground mining operations for pyrite were finally stopped in 1979. In 1971, a major change in the long range mining plans for Masa San Dionisio was established. Between 1971 and 1975, underground mining of pyrites was progressively reduced while open pit extraction was increased in

Jan 1, 1981

By Jack A. Simon, M. E. Hopkins

GENERAL GEOLOGY Coal is defined as a combustible rock that originated in the accumulation and physical and chemical alteration of vegetation. Coal can be ignited and burned like the wood that was man's earliest fuel, but coal gives more heat than the same amount of wood and has many industrial uses. Unlike wood, coal is not generally found on the surface of the ground but is mined from the solid rock of the earth. Before taking up the occurrence, formation, and the unique character of coal in the rock sequence, let us briefly consider the general character of all rocks in the crust of the earth. Relatively little is known about the very earliest history of the earth, although a number of logical theories have been developed. Manned exploration of the moon and the rocks returned to earth continue to provide some answers to questions concerning the earth's origin and history. The period of earth history with which we concern ourselves here begins after great areas of water had evolved on earth and substantial land areas of once molten (igneous) rock existed. Weathering and other processes that attacked the surface of the rocks reduced them to small particles. Water provided by rainfall transported this material, ultimately, to large bodies of water where it was deposited. Thus was initiated the geologic sequence of sedimentary rocks that lie above the once molten igneous rocks. The crust and upper mantle of the earth are made up of several large plates along which differential movement (primarily horizontal) takes place. Such movements, although small, are occurring today. These horizontal movements are accompanied by vertical movements causing important changes in the relative position of the continents and oceans. Low-lying coastal swamps with favorable climates are ideal locations for coal accumulation and burial by river-borne sediments, and large areas

Jan 1, 1981

Located 19 km (12 miles) north of the Carlin gold mine and 43 km (27 miles) north of Carlin, Nevada, is Carlin Gold Mining Company's Bootstrap mine. This deposit is similar in character to the Carlin ore, except it occurs in the upper plate formation of the Roberts thrust fault rather than in the lower plate rocks. The deposit was discovered over 50 years ago and operated on a small scale in the early 1960s using vat cyanide leaching. Newmont Mining Corporation acquired the property in 1967, and from an open pit mined 650,000 mt (717,000 st) of ore which was trucked to the Carlin conventional cyanide plant. (See Gold and Silver Cyanidation Plant Practice by F. W. McQuiston, Jr. and R. S. Shoemaker, Society of Mining Engineers, AIME, 1975. ) With the same grade of ore, the gold recovery by conventional methods is somewhat lower than that of the Carlin ore, even with a finer grind. Leaching tests were first conducted by the United States Bureau of Mines in 1968; and in 1971, ‘72, Carlin conducted extensive cyanidation investigations by bottle testing, simulated heap leaching in tall columns, and small scale pad heap leaches. Gold extractions ranged from 55% to 95% with low reagent consumptions. In 1974, a 545 mt (600 st) heap leach test was made at Carlin on pit-run low-grade material assaying 1.37 g per mt (0.04 oz per st). In a six week period the extraction of gold was 47.57'0. Carlin uses atomic absorption analyses on cyanide leach liquors to determine potential leach ore grade rather than fire assaying because it gives a more practical assessment of leach recovery than does fire assaying, which accounts for the total gold content. Before open-pit mining was started, plans were made to heap leach, the ore at Bootstrap which was too low grade for transport to Carlin. The topsoil outside of the designed pit area overlaid ancient lakebed clays which were found suitable for compaction to form an impervious base on which the dumps to be leached could be placed. By using the cost of truck haulage and milling at the Carlin plant and the price of gold 'at that time, a cutoff grade was established which resulted in the gold content of the first 150,000 mt (165,000 st) of the heap leaching ore being 1.51 g per mt (0.044 oz per st). An additional 500,000 mt (552,000 st) of lower grade material, assaying 0.96 g per mt (0.028 oz per st), is available for leaching as economics permit.

Jan 1, 1981

By G. L. Schroeder, C. H. Summers, D. B. Lindsay

INTRODUCTION The requirement that is placed on owners and operators of underground mines to protect workers against the health hazard of inhaling radioactive materials which are short-lived decay products of 222Rn can be satisfied by applying a considerable variety of what we may call "engineering" solutions as well as a number of "administrative" remedies to the problem. The most obvious of the "engineering" approaches has always been that of forced ventilation, in which relatively clean (i.e., radon-free) air from aboveground is drawn or pushed through the mine workings by a system of fans and ducts. This relatively clean air, in sweeping through the drifts, stopes and haulageways, dilutes the radon and radon-daughter concentrations in the air of the mine, and performs the added beneficial function of removing the daughter-mixture quickly enought to limit grow-in of the longer-lived nuclides in the group that make up the "toxic trio" on which the Working Level (IM) unit is based. Effective as the dilution-ventilation method is for control of WL in most underground mining situations, however, the increasing strictness of control measures that have been imposed on the mining industry over the last two decades have demanded measures of even greater effectiveness. In times of poor markets for yellow-cake and other products of the mines, mine operators are pressed to reduce operating costs, and the installation of additional primary ventilation capacity can be a severe burden on a mine that is already laboring under an unfavorable earning power. When traditional dilution-ventilation systems alone cannot meet the requirement for WI, control, radiation safety engineers and ventilation engineers begin to look at alternatives and auxiliary methods. Since the radon which produces the toxic daughter products originates in the rock of the mine walls, and since, in most United States mines, that rock is a porous sandstone through which air can move under the effect of atmospheric pressure gradients, and through which radon can diffuse relatively freely, one way to help control the growth of WL would be to hinder the escape of radon from that reservior of porous rock. An appealing; method for hindering that natural flux of radon-polluted air from the walls of the mine has long been apparent; namely, to apply a low-permeability coating over the surface of the rock, thus sealing the radon in place and, in theory at least, preventing its escape into the mine air. Our 1970 report to the U.S. Federal Radiation Council on the subject of cost impacts of proposed changes in the occupational standards for exposure of underground uranium miners to airborne radon daughters noted the possibility of using polymeric wall sealants as a means of controlling radon-pollution of mine air. Since that time a number of reports have appeared in the technical literature advocating this technique for restraining the escape of radon from building materials, mill tailings, and other materials containing 226Ra, in addition to the surfaces of underground mine workings. During this period, some controversy has occurred over the question of the probable effectiveness of wall sealants in limiting the escape of radon from the rock. Our 1970 report speculated that flaws (cracks and "pinholes") in the coating might be all but unavoidable in practice, and that even a conservative estimate of the frequency of such flaws would lead to a prediction of ineffectiveness. Hammon et al, in a laboratory evaluation of radon sealants conducted by Lawrence Livermore Laboratory of the University of California in 1975 on behalf of U.S. Bureau of Mines, concluded that a wide variety of polymeric coatings would provide "nearly 100% effectiveness" in restrain¬ing escape of radon from mine wall surfaces if applied in "thicknesses between 5 and 10 mil" (125-250 [y]pm). John Franklin and co-workers at the U.S. Bureau of Mines laboratories in Spokane, Washington, have carried the experiments with polymeric sealants through additional laboratory tests and into actual mine environments, reporting that selected sealants could provide attenuation of radon flux by a factor of four (75-80% reduction). Robert Bates and John Edwards of USBM developed a computer-assisted mathematical/physical model that predicts a relatively small effect of flaws in a low-permeability coating on the radon flux from a sandstone-type matrix. FIELD TEST Since all actual experimental work with wall sealants showed some beneficial effect on radon attenuation (even if not as exciting as the "nearly 100%" predicted by Hammon), USBM was encouraged to extend its evaluation to an actual operating uranium mine, and awarded a contract for that work to Arthur D. Little, Inc. in September 1979. We were fortunate in obtaining the voluntary cooperation of Atlas Minerals Division of Atlas Corp., who operate a mill and several underground mines in and around Moab, Utah. Atlas made available for our use a small T-shaped drift in their Pandora Mine in LaSal, Utah, and provided space for instrumentation and recordkeeping by our field crew in a surface building near the mine entry. Atlas also provided electricity and water to the test site, together with assistance in establishing necessary ventilation, removing rubble from the site, conducting periodic WL surveys and furnishing auxiliary man-power for the heavy hard work of coating the walls with gunite prior to application of the polymeric sealant. The generous coopera-

Jan 1, 1981

By J. W. Walkiewicz

The Bureau of Mines investigated alloys containing mischmetal (MM), cobalt, copper, magnesium, and iron for use in permanent magnets in place of the scarce samarium-cobalt alloys. The magnetic properties of MM-Co, MM-Co-Cu, MM-Co-Cu-Mg, and MM-Co-Cu-Fe-Mg alloys were evaluated. Magnets were fabricated by powder metallurgy consisting of arc-melting the metals, crushing and grinding the resultant alloys, alining and compacting the powder, and sintering the compacts. Magnetic values of MHc = 4.7 kOe, BHc = 4.07 kOe, Br = 6.81 kG, and (BH)max = 10.0 MGOe were obtained with a MM-Co alloy containing 36±0.5 wt-pct MM. By substituting copper and magnesium for part of the cobalt, the values for MHc and BHc were increased to 29.0 kOe and 5.89 kOe, respectively. This intrinsic coercivity value exceeded that of Sm-Co alloy obtained in our laboratory. The addition of iron to MM-Co-Cu-Mg alloys resulted in an increase of Br to 6.90 kG and (BH)max to 10.3 MGOe. Copper and magnesium contents of these alloys were optimized to obtain maximum values of MHc.

Jan 1, 1981

By Robert C. Freas

While on the surface limestone marketing may appear mundane, it has continued to provide a series of challenges beyond the realm normally envisioned with this industry. This paper presents a case history of a mature and well-established quarry company that has attempted to keep pace with an ever-changing economy. It examines the impact of socio- economic and technological factors on the company's marketing efforts, and looks at the role of both short and long range planning. The realities which have had to be faced and how product requirements have been kept in balance with production restrictions are also discussed.

Jan 1, 1981

By S. G. Malghan

Steel consumption forms a significant part of the operating cost of a minerals processing plant. An estimated one-quarter billion kilograms of steel in the United States and over one-half billion kilograms in the world are consumed each year in wet grinding alone. The depletion of ore grades and the necessity of finer grinding of abrasive ores are expected to increase the steel consumption even higher. Through continued research and development by the mining industry and the suppliers of steel products several remedies to reduce steel consumption have evolved. This paper critically reviews the mechanisms involved in steel wear, and currently available methods, materials and operating conditions for reducing steel consumption. Particular attention is given to liner design modifications and substitution of steel liners with rubber liners.

Jan 1, 1981

By H. D. Freeman

The occurrence of gold in refractory gold ores varies widely and affects the recovery process. The determination of gold and the composition of the associated minerals are important in selecting an appropriate processing scheme. However, locating the gold in an ore sample is a difficult task which requires perseverance, luck, and experience. Our experience has led to the development of a relatively fast and reliable means of deter-mining the mineralogy of ore samples through analysis combining an energy-dispersive x-ray analyser coupled to a scanning electron microscope (SEM). In some cases, a wave length dispersive spectrometer or microprobe is used to further quantify the various mineral compositions. The SEM/microprobe analysis identifies the source of problems that may arise during the recovery of gold from refractory gold ores.

Jan 1, 1981

By Raymond C. Voige

"The use of current electronic technology in the design of new underground mine communications equipment is providing improved and expanded voice communications which can, in turn, contribute to improved productivity and safety. A review of equipment that is now available or under development Includes the following categories:WIRED SYSTEMSI.Pager phones with selective calling, audible and visual alerting and message indicator.2. Mufti-conversation pager phones that use multiwire cable ormultiplexing techniques.WIRELESS SYSTEMSLow-and medium-frequency inductive systems utilizing ""near"" magnetic fields for both vehicular and personal communications.Wired SystemsCommunication systems in underground mines have evolved slowly in many parts of the world. For many years, magnetotype telephones were the only means of communication from one mine level to another and to the surface. These units were located near the shaft and communications to the working areas were limited."

Jan 1, 1981