Search Documents

Numerous underground coal mine ventilation seals have been installed in the United States of America prior to 2006 and after implementation of the Mine Improvement and New Emergency Response (MINER) Act. Seal engineering, design, placement, and construction is regulated in industry, but post-construction monitoring of seals is limited to visual inspection of the outby face and seal perimeter, convergence measurement, and atmospheric monitoring. To monitor seal integrity and to provide safe working conditions, a form of non-destructive testing (NDT) is necessary to accurately reflect the health of the seal by detecting post-construction changes, deterioration, or defects within in-situ seals in underground coal mines. Previous research from the National Institute of Safety and Health (NIOSH) has indicated the potential for utilizing ground penetrating radar (GPR) for assessing in-situ mine seals. This paper provides an update to the assessment of proposed NDT methods for seal evaluation using commercially available GPR technologies and systems. Full-scale free-standing seals and large-scale seal specimens were analyzed with an array of GPR units from various manufactures using multiple frequencies.

Feb 23, 2014

St. Peter sandstone is an arenaceous sheet that covers large area in North America. The interest for St. Peter sandstone has been increasing due to the upward trend for hydrofracturing and the consequent need for fracking sand. This material is possesses very unique mechanical properties. On the one hand, it is brittle as characterized by an unusually high friction angle, up to 69°, and steeply curved failure envelopes. On the other hand, it is friable, possessing extremely low, and in most cases zero cohesion. The underground mines that are working under this condition are lacking the ground control techniques for this particular mining environment. The geotechnical properties of the St. Peter sandstone were examined using uniaxial test, triaxial test, porosity test, flexural strength test. This paper aims to investigate the effect of microstructure on strength properties, utilizing microscopic studies, index test (porosity, size distribution).

Feb 23, 2014

By L. Sandbak

The TRJV Mine is located approximately 43 miles northeast of Winnemucca, along the east flank of the Osgood Mountains in the Potosi Mining District, Humboldt County, Northwest Nevada (see Figure 1). The Turquoise Ridge Mine is an underground mine, and is a 25% joint venture partner with Newmont Mining. The TRJV mine utilizes the underhand cut-and-fill mining method due to the relatively low rock quality in the ore zones and the relatively shallow dipping 25-45 degree ore body geometries. This paper defines a rehabilitation risk rating system (RRRS) for prioritizing rehabilitation of drifts damaged in the mining processes including long term development drifts providing access to the mining areas. The ultimate use is as a mine planning tool for the organized scheduling of rehab in a timely manner. A few case studies of the most needy rehab areas identified by the RRRS mapping system is presented, and the type of rehab completed design for these areas. Suggestions on improving the rehab risk mapping system include the use of support history and rock mass strength rating factors.

Feb 23, 2014

By M. Baumann

Operating and maintaining the heavy equipment used in open-pit mining operations is an ongoing challenge for mines. Typical operations employ a combination of shovels, wheel loaders, and haul trucks to excavate and transport the material for further processing. As this is the first point of contact for the material after blasting, it is often a bottleneck of all downstream processes, thus, equipment uptime and efficiency is crucial. Automated systems for bucket tooth monitoring, payload measurement, proximity detection, and rock fragmentation analysis will be examined. The impact of these systems on operation safety, efficiency, and reliability, in real-world scenarios will be investigated. The process of managing all the above fleet of equipment in a mine can be streamlined by connecting the equipment monitoring systems to a central server. Using the central server, the distribution of this information can be automated to ensure that the right people see the data in a timely manner, improving both proactive and reactive responses to threats to safety and productivity.

Feb 23, 2014

By S. Que

Local community acceptance is a key aspect of planning and managing mining projects, whether through sustainability assessment and reporting or corporate social responsibility programs. However, there has been very little research to understand the determinants of community acceptance. This paper seeks to identify key mine characteristics and demographic factors that influence individual acceptance of mining projects. Six demographic factors and 16 mine characteristics were selected based on literature review. Four of the six demographics factors were confirmed to be significantly (p < 0.05) correlated with people?s attitude of the importance of the mine characteristics. All sixteen mine characteristics are identified as important factors. The most important mining factors are Job opportunities, water shortage or pollution, air pollution and land pollution. Both the mining and control groups have same opinion of 12 mining characteristics and differ on four (infrastructure improvement, labor shortage for other businesses, noise pollution, and mine life). During design and management of mines, this data can be used as a reference. This result will facilitate better choice experiment (survey) design for discrete choice modeling. Such discrete choice models can provide a viable framework for data-driven community engagement and sustainable mine management.

Feb 23, 2014

By P. James

Blue Planet Strategies (BPS) focuses on improved resource utilization and targets converting wastes into resources. New BPS capability (DEMET) wrings extra value from mining and processing wastes by enabling new production from waste and residual sources. This powerful platform technology provides considerable processing flexibility and enables various new economical treatment options to extract key metals from low level and process byproduct stream sources normally left as waste by traditional processing methods.[1]

Feb 23, 2014

By J. Tavares

It is no mystery why the mining industry has such lofty safety standards. In dealing with Mother Nature and gravity, the combination of the two can create significant hazards from high wall and tunnel collapses to huge landslides. The loss of production from a major disruption could be enormous. The price tag on the loss of human life is immeasurable. The evolution of geotechnical instruments and software has been ongoing for years. But the biggest innovations have occurred during the era of cell modems, internet, and wireless networks, allowing for real time data and alarms to be delivered globally anywhere and anytime to one?s computer, laptop and smartphone. Yet in some ways you can thank the urban construction projects for developing much of the technology in use by today?s mines. Due to the density of population and the billions in dollars of structures and infrastructure in cities throughout the US and the world, urban projects have faced intense scrutiny for years. Out of this scrutiny was born the necessity of real time automated monitoring of instrumentation and sensors, a defence against catastrophic failures, and real time early warning systems through alarms that can and do saves lives. It is also possible to identify areas of concern with subsequent remediation prior to failure.

Feb 23, 2014

By D. Spitty

Mining companies often have many disparate systems and repositories of data in their organization for planning and scheduling outbound mining supply chains. To optimize ore quality, throughput, transport logistics scheduling and delivery to contract, planning teams need to model and manage the value chain accurately and achieve a consolidated, enterprise view of operational performance. Planning teams coordinate a complex series of activities to ensure production forecast accuracy. They also negotiate and execute complex contracts often with disconnected and limited visibility of production forecasts, quality, and variability with little ability to accurately market potential product specifications over longer time horizons. This market is becoming increasingly dynamic, with increasing variability and the time for planning teams to react is decreasing. This is driving the need towards using science to generate the necessary scenarios required to support the decisions made by planners on a frequent basis. Resource-to-Market is a highly flexible, user-configurable supply chain management system for the mining and metal processing industries. This provides an integrated view of the supply chain that supports the dynamic nature of planning in a mining company, embraces variability of elements across the supply chain with the ability to optimize across all the functional areas of the operation to enable optimal decision making for often competing objectives such as throughput, quality, cost, revenue and profit.

Feb 23, 2014

By D. Zim

Mining activity in South America is a growing enterprise. One of difficulties found in many areas of the South American continent, especially in north Chile and south Peru, is the shortage of water supply. In order to overcome this difficulty some mining companies proposed to transport the water from Pacific Ocean up to the mountains. This can be accomplished by the use of stainless steel pipelines, but this is a cost prohibitive solution and is also subject to severe pitting corrosion in a saline environment. The use of mild steel may be a lower cost solution than stainless steel as the material of construction for pipelines but it is subject to corrosion anyway. The corrosion in this case can be internal or external corrosion although cathodic protection as well preventive maintenance usually is enough to mitigate external corrosion without the need to shut down the pipeline. The same is not true about the prevention of internal corrosion. It is not practical, sometimes not even possible, shutdown a pipeline to carry out an inspection and fix sections where potential failures are detected. It is possible avoid corrosion caused by sea water within the mild steel pipelines by applying a proper chemical program designed to virtually eliminate dissolved oxygen in the water commonly called deaeration.1 This type of treatment obviously involves additional capital investment since it requires the construction of one deaerator with the first pumping station and additional equipment at each point where the water can come into contact with oxygen. Deaerators will increase operational costs and subsequent injection of chemicals will be required in the case of multiple degasification facilities thus increasing the consumption of chemicals. grams based on oxygen scavengers, the objective of the present study is to develop a new water treatment capable of preventing mild steel corrosion in aerated sea water. The new treatment must be able to prevent both generalized and localized (pitting) corrosion and overcome the necessity to construct and operate deaerators.

Feb 23, 2014

By M. A. Oskouei

Draglines are dominant machines and the most electricity consumers in surface coal mines. With the growing price of energy, environmental concerns, and the high sensitivity of mine profitability to dragline productivity, any improvement in efficiency of draglines can be beneficial for mines. Research has shown that operator skills have a significant impact on energy efficiency of loading machines. This study suggests a method to identify the key parameters that lead to differences in operator energy efficiency (responsible parameters). First, correlation analysis is used to identify parameters that are correlated to energy efficiency. Second, linear regression of a difference matrix is used to determine responsible parameters. Since this method is based on pair-wise comparison of operators, equal number of cycle is required for pairs of operators. Complete case analysis (CCA) is used to handle missing data problems. The final conclusion is made after removing the effect of random sampling and by considering all pairs of operators. Identifying responsible parameters can improve operator training programs. The suggested method is illustrated with a case study using field data.

Feb 23, 2014

By J. Paraszczak

Application of teleoperated and automated (or ?autonomous?) mobile equipment in underground metal mines is a promising avenue for overcoming some of the challenges facing mine operators. These include, but are not limited to, the issues related to safety and health of underground workers, better use of the shift time leading to increased productivity, skilled manpower shortages, and remoteness of some mine sites. Autonomous load-haul-dump machines and trucks offer several benefits over man-operated ones, but their use at their full capacity is a challenging and complex task. This paper makes an overview of commercially available equipment and systems and their applications. It examines factors affecting adversely availability, utilization, and production efficiency of autonomous vehicles and compares them to conventional man-operated machines. Technical and operational aspects are discussed and their criticality is analyzed. Based on that, recommendations concerning means and measures that may help raise operational effectiveness are given. It is stressed that due to a scarcity of publicly available information on the performance and cost of autonomous loading and haulage operations, more field studies and in-depth analysis are needed.

Feb 23, 2014

By M. L. Harris

Explosions in underground mines and surface facilities such as processing plants are caused by confined accumulations of combustible dust and/or flammable gas mixed with air in the presence of an ignition source. Underground explosions can be prevented by minimizing methane concentrations through methane drainage and ventilation, by adding sufficient rock dust to inert the coal dust, and by eliminating ignition sources. The effectiveness of rock dust in arresting explosion propagation was proven by experiment and practice (1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11). The precise mechanism by which rock dust (generally pulverized limestone dust) quenches flame has not been fully explained, but is believed to be absorption of thermal energy from the heated gases and absorption of radiant energy, which reduces the preheating of unburned coal particles ahead of the flame front. One measurable aspect of explosibility is incombustible content. In order to determine whether enough rock dust is applied, 30 CFR1 § 75.403, Maintenance of Incombustible Content of Rock Dust, requires at least 80% incombustible content on the roof, ribs, and floor of underground coal mines. 30 CFR § 75.403-1 further defines the incombustible content as follows: ?Moisture contained in the combined coal dust, rock dust and other dusts shall be considered as a part of the incombustible content of such mixture.? In order to determine the incombustible content of the mine dust, samples of deposited dust from specified areas in a mine must be collected, analyzed, and then compared with the minimum standard of 80%. The traditional low temperature ashing (LTA) approach to determine if a coal and rock dust mixture is compliant with the inerting requirement consumes the coal dust and considers the remaining material to be inert. Compliance with the law is then determined by comparing the measured percentage of inert material of the representative band sample with the pre-established requirement of 80%. The incombustible content of the sample includes rock dust, the amount of moisture as received at the lab, and the inherent ash in the coal. The LTA method is not itself a direct measure of explosibility but is a surrogate that calculates a single parameter associated with large-scale Bruceton Experimental Mine (BEM) explosion test results conducted with dry rock dust. This method assumes a homogenous mixture with no layering of rock dust and coal dust. Float coal dust is a serious explosion hazard if it accumulates on top of the rock dust and is not mixed with the rock dust (12). Mitchell and Nagy (13) studied the effectiveness of water as an inerting agent for the coal dust explosion hazard. The study emphasized that surface water evaporates readily from dusts. Thus, in a passageway where the dust is wet, changes in weather or the ventilation system could dry the dust and make it unsafe in a relatively short period of time. Where adequate rock dust has been applied, this drying effect is not a factor. However, if the mine depends upon the moisture content as part of the incombustible content, fluctuations in the dust surface moisture within a mine can render moisture content an ineffective and inconsistent measure of safety. Additionally, if sufficient moisture is absorbed and subsequently relinquished by rock dust, a cake can form and render the rock dust ineffectual. The trend has long been recognized that mine explosions occur primarily during the winter season when the humidity is low for long periods of time (14, 15, 16). In light of this trend and due to the potential variability of the moisture content of the dust, it may not be prudent to include variable surface moisture in the total incombustible content of the sample. Instead, surface moisture should be viewed as an additional safety measure as long as the rock dust is dispersible. However, moisture limits the ability of the rock dust to disperse and can significantly reduce its capacity to effectively inert propagating explosions (2, 13, 17, 18, 19, 20, 21, 22). Given the methods by which the as-received moisture and incombustible content are determined, dust samples from the 2010 MSHA database were assessed to determine the variability of the moisture content throughout a year and how often the measured as-received moisture might have affected the dust explosibility determination if removed. The findings were then verified by observation in laboratory studies and within the NIOSH OMSHR Safety Research Coal Mine (SRCM).

Feb 23, 2014

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014

By L. Schlink

Impacted waters, often complex, are created in mining which at some point in the mine life cycle will need to be attended. The simplest and most cost effective method of handling impacted water is to reuse it as makeup water for operations. At the end of mine life, operational reuse will not be an option and the impacted water will require treatment to achieve alternative reuse goals. Conventional mine impacted water treatment is successful in removing unwanted constituents but create brine and sludge that may require special handling or additional treatment, resulting in additional liabilities and costs. Freeport-McMoRan Copper & Gold has taken an approach to water treatment that focuses on transformation not concentration. The Water Treatment Test Facility located at Sierrita Mine has three test plants that are piloting the mine impacted water transformation process. Two plants have been designed for the removal of calcium and sulfate with products of gypsum and sulfur. The third plant removes metals from process water and transforms them into marketable metal sulfides. The transformation, rather than concentration, of mine impacted water solutes greatly reduce long term risks.

Feb 23, 2014

By D. D. Faulkner

Cable bolts anchored with traditional two component polyester resin cartridges have successfully supported difficult roof conditions in underground mines. Resin cartridges provide a cost-effective cable bolt anchoring system with consistent anchorage performance characteristics when properly installed. The most commonly used cable bolts in the U.S. mining industry are 270 ksi (1,862 MPa), 0.7 and 0.6 inch (18 and 15 mm), seven-strand smooth cable with resin mixing bulbs (also known as bird cages), and 40- and 30-ton nominal capacity, respectively. However, there are other types of cable bolt anchoring systems aside from bird cages. Recently, many questions have been raised regarding the anchorage characteristics of various types of cable bolts. Keystone Mining Services, LLC (KMS), the affiliated engineering company of Jennmar Corporation, conducted a variety of controlled tests developed to closely model actual underground installations. These tests compared the performance of three commonly used cable bolt varieties, including plain, bird caged and indented seven-strand cable. Details of the laboratory testing and comparative analysis of the results are provided.

Feb 23, 2014

By J. F. Brune

This is a shortened version of the paper ?The Methane-Air Explosion Hazard Within Coal Mine Gobs published in the 2013 volume of SME Transactions (Brune, 2013). This paper analyzes the explosion hazard resulting from the formation of methane-air mixtures in the mined-out gobs of underground longwall coal mines. Evidence from numerous mine explosions suggests that explosive methane zones can form within longwall gobs. Explosions and fires resulting from these methane accumulations have led to severe and fatal injuries to the miners, including the explosion of the Upper Big Branch mine in West Virginia, where 29 miners lost their lives. The paper also reviews current research on numerical modeling of gas flows in longwall gobs and outlines how targeted injection of nitrogen into gobs can effectively reduce the volume of such explosive methane zones. The paper concludes that comprehensive monitoring of gas compositions along the accessible fringes of the gobs along with inertization, improved ventilation schemes and further research are necessary to control this explosion hazard and make mining operations safe.

Feb 23, 2014

By S. D. Abbott

Mines are filled with a mixture of gases, some of which are toxic, flammable, or explosive. Others serve as early reporters of impending problems. Mines monitor these gases in order to ensure the safe, efficient operation of the facility and avoid losses or disasters. Two different approaches to monitor these gases have historically been taken. One kind of device measures the amount of each gas present by using selective detectors (e.g. handhelds and spectrometers). Another kind separates the mixture of gases into the individual constituents, then measures the amount of each gas present (e.g. gas chromatographs). Handheld units are the most widely used, but gas chromatographs are the most powerful yet underutilized units available to enhance mining operations. There are many misconceptions about the nature, applicability and proper use of each type of device, and little data is available. Up to this point, many people had only the manufacturers? claims to guide them. This study was undertaken to clarify the range of applicability, important characteristics, and value in use of these units in real-world situations. An additional goal of the study was to provide ways to evaluate comparative data, and thus aid mining operations in choosing the most beneficial and reasonable ways to use such devices in various situations and contexts.

Feb 23, 2014

By D. K. DeForest

The olfactory system (sense of smell) is crucial to the ability of fish to avoid predators, recognize kin, and synchronize reproduction (Baldwin et al. 2003). Copper (Cu) has been shown to impair olfaction in juvenile freshwater life stages of salmonids (including Pacific salmon and trout) in some laboratory experiments; and in the United States, public concerns have been expressed that current regulatory criteria for Cu in fresh water are not adequately protective of olfactory function in salmonids (e.g., OSU 2007; Pearson 2007). These concerns have largely been raised because some Cu concentrations that have caused olfactory impairment in salmonids in the laboratory are less than Cu concentrations that have been shown to reduce salmonid survival, growth, or reproduction (the effects endpoints that are typically considered in deriving ambient water quality criteria). However, two important and interrelated points that must be considered: (1) freshwater Cu criteria are "driven" by the sensitivities of several invertebrate species that are more sensitive than the olfactory impairment threshold in salmonids when (2) the influence of water chemistry on Cu bioavailability is properly considered in deriving Cu criteria. Bioavailability refers to the ability of various chemical forms of Cu to interact with receptors on the surface(s) of organisms and thus directly cause toxicity or uptake by the organisms. The toxicity of Cu and other metals to aquatic organisms is a function of water chemistry. For example, acute Cu toxicity in fresh water generally decreases as pH, water hardness (Ca2+ and Mg2+), alkalinity, and dissolved organic carbon (DOC) concentrations increase (Meyer et al. 2007). The U.S. Environmental Protection Agency (USEPA) has recommended hardness-based freshwater aquatic life criteria for Cu and other metals since the 1980s (e.g., USEPA 1985); and hardness-based metals criteria decrease (i.e., become more restrictive) as water hardness decreases. More recently, the USEPA has recommended freshwater aquatic life criteria for Cu based on the biotic ligand model (BLM; USEPA 2007), which accounts for the influence of multiple water chemistry parameters, including DOC, pH, alkalinity, Ca2+, Mg2+, and several other cations and anions. The BLM-based Cu criteria generally decrease as DOC concentration, pH, alkalinity, and water hardness decrease. Because DOC has a stronger influence on Cu bioavailability than water hardness, hardness-based and BLM-based Cu criteria can differ considerably. For example, in water that has low DOC and high hardness, the hardness-based Cu criterion would be relatively high (because it is driven by the high hardness) but the BLM-based Cu criterion would be relatively low (because it is driven by the low DOC). Thus, any evaluation of the protectiveness of Cu criteria against a given effect, such as olfactory impairment, must properly account for the chemistry of the exposure water. Meyer et al. (2013) compiled data on Cu-induced olfactory impairment and olfactory-induced behavioral effects from tests in which BLM parameters were measured. They demonstrated that the USEPA&apos;s BLM-based freshwater life criteria for Cu are protective against olfactory impairment, because it adequately accounts for water chemistry (whereas the USEPA&apos;s hardness-based Cu criteria are not consistently protective). Olfactory impairment by Cu is now receiving increased attention in Canada and Europe (e.g., Wall 2013; Stang 2013). Accordingly, in this paper we have expanded the analysis of Meyer et al. (2013) to consider copper guidelines from various other countries and whether these guidelines are protective against olfactory impairment.

Feb 23, 2014

By M. Fan

Coal has in general a wide range of density from minus 1.3 to plus 2.0 g/cm3 because of its variations in purity, rank, and porosity, etc. The coal density has great impact on froth flotation performance, but much less attention has been paid to particle density than particle size. Our previous research results demonstrated that cavitation-generated nanobubbles around 700 nm in diameter can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubble on the flotation performances of different density fractions (minus 1.3, 1.3-1.4, 1.4-1.5, 1.5-1.6, 1.6-1.8, 1.8-2.0, 2.2-2.2, and plus 2.2 g/cm3) of coal was investigated using a bank of 10-liter flotation cells, a specially designed 50-mm-inside-diameter column, and a 152-mm-inside-diameter column. It was found that nanobubble has the biggest impact on the flotation performance of 1.4-1.8 g/cm3 medium-density coal particles.

Feb 23, 2014

By L. Sandbak

The Turquoise Ridge Joint Venture (TRJV) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestones, siltstones, and mudstones. The weak nature of the ground facilitates the underhand cut and fill mining methods. TRJV has been working to optimize ground support and mechanize top cut drift sizes and eliminate operating hazards associated with jackleg drilling. Safety Factor analysis based on bolt strengths has allowed us to pursue larger sized top cut drifts and to evaluate bolt length sizes and spacing. Switching from jackleg sized drifts of 10?W x 10?H to a mechanized 12?H x12?W top cut drift design has the potential to decrease overbreak, provide more uniform drift design sizes and bolt patterns, and increase ore production by at least 38%.

Feb 23, 2014