Search Documents

By J. Kalejta

Ever increasing depth of mineral extraction presents a challenging environment for hard rock underground mines. High in-situ stresses and associated seismicity with potential rockburst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. This paper describes a method of mechanized installation of a chain-link mesh evaluated at the Kiruna mine in Sweden and South Deep Mine in South Africa. A purpose-built mechanized roll mesh handler was used in this evaluation. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilizing the hydraulic circuit normally used for the feed arrangement. A number of key performance indicators have been identified as success criteria: ??A 30-50% faster installation compared to the conventional methodology ??The mesh should sustain any blast damage when applied to the blasting face ??No unraveling of the mesh when cut ??No failure of mesh under normal conditions Although the energy-absorbing mesh combined with yielding rock bolts is a ground support system of choice for rockburst prone conditions, the operational upsides recognized during the evaluation imply that this product can also be competitively used in less demanding ground conditions where customarily weld mesh or shotcrete are used as a primary surface support. The main conclusion: a fast, safe and fully mechanized installation.

Aug 1, 2013

By H. Nejati

Experimentally, the Semi-Circular Bending Moment (SCB) fracture toughness test results of Basalt Specimens Under Illumination (BSUI) have shown reduction in fracture toughness and failure force as a result of micro-cracking. The fractographic investigation of BSUI confirms initiation and extension of micro-cracks. Determination of a relation between strength reduction (herein fracture toughness reduction) and density, location and orientation of thermo-mechanical induced cracks due to microwave radiation is critically important. Numerical modeling can bridge strength reduction and the density of thermal microcracks generated due to microwave radiation. Discrete Element Modeling (DEM) is a power tool for simulation of micro-crack initiation, coalescence into macroscopic fractures and failure mechanisms in brittle rock specimens under different stress regimes (herein combination of pure tensile stress due to SCB testing, and thermal stress due to microwave radiation). For this purpose, a DEM modeling of SCB testing of basalt using EDEM (i.e., a DEM based software). DEM models are calibrated according to results of experimental SCB testing as reported in previous papers. This paper first reviews some background data on SCB fracture toughness, and experimental results of fracture toughness of microwave treated SCBs. Then it proposes a new methodology for simulation and validation of rock samples exposed to microwave illumination with regard to experimental results, and discusses the correlation between fracture toughness of BSUIs and density of micro-cracks, which is attributed to applied microwave power and duration of illumination.

Aug 1, 2013

Leadership "Organizing a group of people to achieve a common goal" Paradigms ? Rush to produce or cut costs. ? The most important thing after safety is production. ? We?ll take care of ??this?? once in production. ? I know what to do, 30 years of experience in mining. ? I want a 100% reliable operation.

Aug 1, 2013

By Julian V. Simela

Conventional methods of underground surveying use theodolites/total stations and 3D laser scanners to obtain information about the underground environment. Current methods of geo-referencing these instruments to a mine reference system include triangulation, trilateration and resection. However, despite technological advancements, surveying procedures have remained slow, laborious and relatively unchanged during the last half-century. Recent innovations in the robotics community have shown that automated mapping of underground mining tunnels can be undertaken using 2D/3D laser scanners. These techniques have the potential to, in turn, improve upon current underground surveying and mapping methods. Automating surveying and mapping using current surveying tools without changing the setting up procedures or removing current constraints, or even changing the type of equipment used, does not change the status quo. The problem of moving from a static, tripod based surveying and mapping system to an unconstrained mobile surveying and mapping system is the subject of this paper. A current challenge for automated mapping is the ability to automatically geo-reference a mobile mapping system to a mine reference system. For a mobile mapping system that uses a horizontally mounted 2D laser scanner to gather data of the underground environment, the challenge of determining its position and orientation within the mine environment is magnified even more. This paper introduces Mobile Automated Scanner Triangulateration (MAST), a technique under development at Queen?s that is designed to geo-reference a mobile mapping system to a mine reference system for the purposes of underground mine surveying. MAST quickly and automatically determines scanner 2D position and orientation (azimuth) in a mine reference frame by using minimal human input.

Aug 1, 2013

By S. Beitler

The availability of renewable energy does not meet the demands of consumption. Hence, fossil fuels will continue to be an important energy source, and coal promises to cover the requirements for the coming decades. Because of its high energy content, deep lying bituminous coal and anthracite are important for energy generation. One trend in the future of coal mining is thin seam mining, because thick seams more and more have been exploited. A well-known and approved longwall mining method for thin seams is plowing which has big advantages compared to a shearer because of its compact design. The extraction of those thinner coal seams will become more and more important in coal industry and therefore the plow will receive more attention in future. Most approaches in longwall automation are focused on the shearer and need a more or less intelligent exploitation machine. Therefore those approaches cannot be used for the plow technology. The authors introduce a shield-data-based horizon control (SDHC). The developed approach integrates the shield data provided by the roof support and process monitoring into the horizon control process to keep the plow in seam even if the seam trend changes. This control concept can be used for the shearer as well as for the plow. The basic idea of SDHC for plow application will be introduced in this paper and first simulation results will be shown.

Aug 1, 2013

By Yan-Jun Shen

The rock mass classification system, BQ (basic quality), is the only national system that is suitable to most kinds of rock engineering in China. It uses two main aspects of the rock mass, the intact uniaxial compressive strength (UCS) and the rock intactness index (KV), to obtain the rock mass BQ. The index KV could be measured by the acoustic wave method. However, because this method is an indirect approach to characterize the rock mass structure, misfits often occur between the test results and the actual rock mass characteristics. Therefore, a new parameter KGSI expressed by the geological strength index is proposed to replace the original KV, and a new method is presented to express the value of BQ as a function of the UCS and the KGSI. Then, the underground excavations at five hydropower stations were chosen as examples to study the relationship between the revised BQ and the each of the international systems (RMR, Q or RMi). In addition, the applicability of the RMR, Q, or RMi system is discussed for China?s rock characteristics and geological conditions, and suggestions are given for improving the revised BQ system.

Aug 1, 2013

By R. Liu

As Building Information Modeling (BIM) becomes widely adopted by the construction industry, it holds undeveloped possibilities for supporting Facility Management (FM). Some FM information systems on the market claim to address the needs for FM requirement. However, the question of whether the functionalities provided by the current BIM-based FM software companies are those actually required by the FM Professionals still need to be answered. The data is required by FM professionals in the operation and maintenance phases of facilities and type of maintainability problems that frequently occur, which can be solved early in design phase, have not yet been addressed. The aim of this paper is to clarify the frequently occurring maintainability problems and to investigate the potential areas that can use BIM technology to solve the maintenance problems in early the design phase. A survey was conducted to collect perspectives from the industry practitioners for the maintenance problems and their frequency. The survey results indicated that maintainability considerations should be taken into consideration during the facility design phase. The results also address the perceived areas by practitioners that need maintainability consideration in design phase

Aug 1, 2013

By D. B. Apel

As depths to the ore bodies keep increasing around the globe, the problem how to deal with the increasing temperature of undisturbed rock mass becomes very important. In extreme cases the rock temperature at the bottom of the mine could raise up to 80 °C. In deep mines, geothermal heat is considered as the primary heat load contributor, which accounts for 50?90% of the total heat load depending on different geological conditions. Thus the geothermal heat control in underground mines is the most important and demanding issue to ensure a suitable working environment. In this study, expanded perlite aggregate (EPA) was incorporated as a lightweight substitute for sand. Five mixtures were prepared using 0, 25, 50, 75 and 100% replacement ratios of sand by EPA. These, mixtures were tested in the laboratory for both the insulating and strength properties of the developed shotcrete. The goal of this research was not only to develop shotcrete which would exhibit good insulating properties but also which would exhibit strength properties similar to the regular shotcrete. This paper not only reports the results of the laboratory tests but also discusses the output of numerical model which was performed to evaluate the benefits of using the insulating shotcrete in reducing the cooling costs at hot underground mines.

Aug 1, 2013

By N. Razavinia

Most mining and metallurgical industries produce relatively large quantities of low grade waste heat which they vent, for the most part, to the environment. To date, little is being done to recover some of this heat and transform it from low grade to a high grade energy form such as electricity. A few decades back this was also true of paper, plastics and metals. Recycling was not a prominent activity. Today, we all know that it is and that recycling is a must for sustainable development. To this end, we feel that we are now at that point in time when the recycling of waste heat to electricity must be given serious consideration. By recycling waste heat one can achieve at least one if not two of the following benefits: 1) reduction in the carbon footprint ? by improving the overall energy efficiency of a process, and 2) production of electricity at an economically viable cost. We have developed a process that captures, concentrates and converts (3 C?s) waste heat to electricity. The process comprises 3 distinct interacting units. The first unit captures and concentrates waste heat using heat pipe technology. The second unit converts some of the concentrated heat to mechanical work which can then be readily converted to electricity. This unit is based on the classical piston/cylinder engine arrangement that is widely used by consumers to power systems with compressed air, for example. The third unit of the process dissipates the heat that the engine cannot convert to high grade energy. It also uses heat pipe technology to achieve this. The combination of the 3 units forms a unique system for recycling waste heat. This paper describes the system and it presents some results that show how the system can be made to be economically viable.

Aug 1, 2013

By P. Hr?enjak

Two groups of methods are usually used in design procedures of underground excavation of dimension stone: the analytical and numerical methods of analysis. In all of these methods the in situ rock mass strength represents the main problem. This is due to massive rocks in dimension stone deposits, consisting of large blocks of rock separated with particular discontinuities, for which the Hoek-Brown empirical criterion, developed for jointed rock masses, cannot be realistically used to estimate rock mass strength, especially for a particular block of rock mass or a particular pillar. On the basis of the regular underground excavation process of dimension stone by separating blocks with the flat jack application, we developed the in situ flexural strength testing method. We carried out numerical analyses and evaluation of uncertainty of measurement in order to validate the in situ flexural strength testing method. On the basis of very good validation results, as well as results of the in situ flexural strength testing of exploitable layers on the ?Kanfanar? quarry, we introduced a new coefficient of reduction, which can be used for correction of other strength parameters determined by laboratory testing for obtaining a realistic value of rock mass strength.

Aug 1, 2013

By A. G. Pathan

Rock and soil mechanics investigations were carried out in block VIII at Thar Coalfield, Pakistan. Most of the strata were mainly composed of sand, with an average content of 67.68 %. Laboratory studies of rock and soil samples from drill hole GT-01 revealed that the strata in block VIII are very weak with an average uniaxial compressive strength of 3.59 MPa, an average tensile strength of 0.68 MPa, an average Young?s Modulus value of 0.234 GPa, an average cohesion of 129.19 KPa, and an average friction angle of 55.47°. Slope stability analysis, based on a probabilistic approach, was carried out using Slide-V software. Monte Carlo simulations have been applied to investigate the probability of failure in the slopes of an open pit lignite mine in block-VIII. From the slope stability investigation, it was found that the probability of failure is 0 % at a slope angle of 16°.

Aug 1, 2013

By Nobuyoshi Yabuki

Building Information Modeling is a prevailing methodology in the building industry and half (by length) of the world's shield tunnels are in Japan. Accordingly, for shield tunnels from 2005 to 2007, we developed a product model called IFC-ShieldTunnel, which is based on Industry Foundation Classes (IFC), in order to meet the future demand for such a product model. IFC-ShieldTunnel was developed by adding new elements that are specific to shield tunnels and that are not included in the original IFC. The added elements include shafts, segments (A, B, and K types), waterproofing elements, segment joint elements, and ring joint elements. Furthermore, soil layers and void elements were created. Recently, we updated the product model by re-organizing the entities and correcting errors. We deployed the updated IFCShieldTunnel model in the construction of an actual shield tunnel in Tokyo for about a year from August 2010 in order to check its feasibility. In the verification process, first, segments were modeled using Autodesk Revit Structure 2011 and property data were assigned to each segment element. Next, a mapping between the original attributes of the entities of IFC and properties of IFC-ShieldTunnel segments was developed. Using this mapping and IFC?s IfcBuildingElementProxy function, we were able to convert the IFC data from Revit Structure 2011 to IFC-ShieldTunnel automatically. Segment data were also converted from Revit Structure to Google SketchUp by IFC-ShieldTunnel. Furthermore, the construction scheduling and cost data were converted from Revit Structure to EXCEL for 4D and 5D analyses of construction. We interviewed engineers who used IFC-ShieldTunnel and received positive comments about the utilization of the product model. Overall, our test demonstrated the feasibility of IFC-ShieldTunnel. In future work, we plan to apply IFC-ShieldTunnel to more projects and test its practicality.

Aug 1, 2013

By S. G. Hardcastle

The effects of air velocity in promoting cooling through the evaporation of sweat generated when working at a high metabolic rate and/or in hot environments is well known. Many of the environmental heat stress indices consider the effect of air movement directly or indirectly within their determination, be it through the use of a specific instrument i.e. a wet-bulb globe temperature meter or Kata thermometer, or inclusion of in the calculation of a stress index, including the effective temperature, air cooling power, thermal working limit, ISO 7933?s predicted heat strain model. Within these models, ambient air temperature, relative humidity and barometric pressure are also considered in varying degrees to quantify an airstream?s capacity to evaporate sweat. Deep mine studies have shown cumulative increases in heat exhaustion rates with both decreasing air velocity and decreasing air cooling powers. However, despite a capacity to cool, the resultant cooling is very dependant on sweat production and its availability for evaporation; these are included where sweat rates and skin wettedness are considered. The first depends on hydration and physiological factors whereas the second is more an engineering factor related to the degree of clothing required. As sweat rates deteriorate with aging, the benefits of evaporative cooling potential can similarly be expected to be diminished. This paper continues to report upon on-going physiological studies exploring the potential for heat stress in deep underground mines through the simulation of mining activities in environmental chambers and a human calorimeter facility. The focus of this paper is to introduce preliminary data suggesting that increasing air velocity (0.5, 1.5 & 3.0 m/s) is beneficial for young subjects (22 ± 1 yrs), as indicated by lower core and skin temperature measures and heart rate during an intermittent work protocol, and then show a lesser benefit for older subjects (62 ± 2 yrs). Both subject groups performed the same task under the same environmental condition (35°C, 60% RH) wearing a standard mining ensemble. The study similar to others being performed under the Deep Mining Research Consortium funded research continues to provide evidence that a greater understanding of heat management processes is required and that worker education is critical as environmental measures and health and safety regulations may not be expected to include all demographic factors such as age, sex and health which are known to affect human thermoregulatory response.

Aug 1, 2013

By A. Bascetin

The mining industry in Turkey has been developing in the last 10 years. Mine wastes and tailings have thus been increasing, depending on the rising production rates. There are many problems related to accidents that occur in tailings damps. In this study, the applicability of the surface paste disposal (SPD) method for a Pb-Zn mine in western Turkey was examined. Density was 3.084 and specific surface area was 0.899 m2/g. The mill tailings have very low plasticity and show characteristics of clays and silts in terms of the Unified Soil Classification System. The particle size distribution of the tailings was 39.2% particles finer than 20 µm. The results of this study showed that the physical and chemical properties of mill tailings make them suitable for SPD.

Aug 1, 2013

By B. Surender Mohan

Mother Earth being a treasure of minerals, it is prime duty of the mankind to preserve this natural source to ensure steady growth of the nation. Utmost care is to be taken to see that these natural resources are explored and exploited scientifically in a sustained manner to ensure that the resource base improves and last longer. In this backdrop, the topic of ?Lignite - its resource and technology options to exploit deep seated deposits? is an apt subject to be deliberated upon in the present context, where the shallow deposits may slowly get dwindled. I shall deliberate upon the resource base of lignite, production profiles of the last five decades, consumption pattern, demand / supply projections, future available technology options to exploit the deep seated deposits, growth trends of the sector etc. in my paper. With the available resource base and future technology options, I can confidentially make a statement that ?lignite will remain as cocontributor along with coal to India?s energy generation and may well maintain its same status in the 21st century too, as it has been in the later part of the twentieth century?.

Aug 1, 2013

By A. Kowalski

This paper presents methods of implementation and the added value that can be achieved by connecting personnel tracking systems and alarm-broadcasting systems. The authors point out the functions of the two systems that enable cooperation between them. Methods for connecting the systems on the surface and underground areas of mines require some intervention in both systems, so the authors point out a possible phased approach to introducing cooperation methods. Due to the fact that tracking systems in Polish mines are at an early stage of implementation, the article aims to provide new functionality, attempts to identify the needs of future users, and describes the experience of both production companies in terms of the development of cooperation methods.

Aug 1, 2013

By J. Parreira

This paper presents a deterministic/stochastic model that was created to compare an autonomous haulage truck system to a manual one by calculating and estimating benchmarked Key Performance Indicators (KPIs) such as productivity, safety, breakdown frequencies, maintenance costs, labour costs, fuel consumption, tire wear, and haulage cycle times.

Aug 1, 2013

By Mory Ghomshei

As fossil fuels become depleted over the next century, it is imperative that Canada and other countries examine ways to transition to other sources of energy, particularly renewable resources. A critical obstacle to developing Canada?s renewable energy resources is the scarcity of infrastructure to wheel the generated electricity to a viable market. For each megawatt of renewable electrical power, a maximum of 1 km of connecting power line is typically feasible. This means that hydropower, geothermal, and wind power projects with capacities up to 100 MW must be located within a maximum of 100 km of a main power line in order to be economically viable. With a total length of about 1200 km, the proposed Northern Gateway oil pipeline project creates an excellent opportunity to become a corridor that can seed renewable energy projects in Northern British Columbia and Alberta. Utility companies must build new infrastructure to provide the electricity for constructing and operating the proposed pipeline. The pipeline and linked power line infrastructure therefore, should be designed and built with consideration to create an energy highway to the significant renewable energy resources, such as hydro, wind, and geothermal, in the vicinity of the proposed pipeline. Some of the important renewable energy resources in northern British Columbia can be developed in connection with the proposed pipeline. It is estimated that close to 2,500 MW of commercially viable wind, geothermal and run-of-river power resources are present in the proximity of the proposed pipeline corridor. While oil flows westward from the Alberta bitumen fields, the generated green power can flow eastward to help the Canadian oil sand industry to offset as much as 10 Megatons of carbon emissions per year. The generated carbon credits are equivalent to 75% of the emissions associated with extraction of the 525,000 barrels per day of oil from oil sands, intended to be carried by the pipeline.

Aug 1, 2013

By J. Chretien

The ability to continuously monitor the air quality within a mine has become instrumental in becoming a low cost producer. The many considerations involved in monitoring air quality include sensor type, hardware placement, as well as data storage medium. BESTECH has had the opportunity to gain insight into these air quality monitoring considerations through deployments of NRG1-ECOTM, a minewide energy consumption optimization system. This paper explores the particular challenges overcome through these installations, and provides a set of guidelines for mines that want to maximize data capture while minimizing costs. It provides a view of additional benefits of air quality monitoring, such as ventilation control, reporting and trending.

Aug 1, 2013

By Xue Yang

Even though many approaches have been proposed for automated fault detection and diagnosis of Heating Ventilation and Air Conditioning (HVAC) systems, and advanced maintenance programs, such as preventive and predictive maintenance have been applied for the systems, issuing work orders for corrective maintenance is still a reality. Currently corrective maintenance still accounts for more than 55% of all maintenance programs in average facilities in the US (DoE, 2010). Indoor air related problems are especially important among corrective maintenance work orders. This paper provides details of a case study conducted to capture the workflow that HVAC mechanics follow, their rationale in diagnosis process and the information they typically refer to while responding to indoor air related corrective maintenance work orders. The general workflow for HVAC mechanics to complete such types of work orders was summarized into 5 stages, and generic information requirements recorded from the case study were synthesized. Initial findings show two main challenges in the industry for HVAC mechanics to get access to required information, which highlights the need for a systematic approach that would enable identification of such information applicable to a given context under which a work order has been generated and provide values of required information for HVAC mechanics to do sound diagnosis through integrated data repositories.

Aug 1, 2013