Search Documents

By S. Chai

Waste dumps are widely used to discharge stripped mine wastes in open pit mining methods. As mining progresses, the height of the waste dumps will increase gradually, which may induce sliding failure once the height exceeds a critical value. Therefore, estimation of the maximum dumping height is crucial to the life-cycle use of a waste dump. However, published information about the maximum height of mine waste dumps are extremely rare. In this study, the maximum dumping height is estimated based on the strength-reduction technique by numerical simulations. The influences of dump geometry and properties on the maximum height are investigated. The results show that the maximum dump height decreases as the dump slope inclination angle α or the unit weight of dump materials γ increases, but decreases when the shear parameters of dump materials (cohesion c and internal friction angle ϕ) increase. The maximum height starts to increase with the ground inclination β when shear failure occurs at the interface between the dump and the base. Furthermore the effects of the dump width B, Young’s modulus E, and Poisson’s ratio μ of dump materials on the maximum height are almost insignificant. Good agreement was found between numerical results available in the literature and those obtained in this study.

Oct 1, 2022

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Numerical lateral load analysis based on the beam on Winkler foundation (BNWF) model (i.e., the p-y method) is a simple, and widely used tool to predict lateral responses of drilled shafts from field load tests. The lack of a site-specific p-y model for cemented soil layers such as caliche is one of the major limitations of simulating lateral load tests conducted in Las Vegas Valley. In this study, some of the existing p-y models for rock materials, such as Florida Limestone and Vuggy Limestone have been evaluated to simulate the lateral resistance of caliche. This has been done in the context of four lateral load tests in caliche-dominant sites from the recently constructed Raiders Stadium project in Las Vegas (NV). The uncertainty in characterizing the material properties of caliche has been addressed. The p-y analyses were performed using NVShaft, a MATLAB-based, comprehensive load analysis program. The applicability of the considered p-y models for caliche material was evaluated by quantifying the normalized error margins between measured and predicted lateral responses from the simulations of the mentioned load tests. Correlations between such errors and the depth and thickness of caliche in soil layers affecting numerical predictions were established, for both up to and beyond design load levels.

Oct 1, 2022

By Gerald Verbeek, Erick Baziw

Downhole Seismic Testing (DST) is an extensively utilized geotechnical tool for site characterization. DST provides low strain (<10-5) in-situ interval shear and compression wave velocity estimates. These velocities are determined by obtaining relative arrival times of source waves as they travel through the stratigraphy and are recorded by one or more vertically offset seismic sensors. The DST arrival times have associated measurements errors and resolution limitations, which become more pronounced as the depth interval of analysis is reduced. Baziw Consulting Engineers (BCE) has developed a new DST analysis technique, the so-called DSTPolyKF algorithm, whereby the arrival times of DST data set are used to define a high order polynomial. The main advantages of this new technique are four-fold: 1) the ability to utilize all arrival time estimates irrespective of measurement errors. 2) the ability to analyze the data with user specified and even small (≤ 0.5m) depth intervals. 3) the ability to apply sophisticated data fusion for significantly more accurate DST interval velocity estimation. 4) the use of polynomial regression accuracy parameters to quantify how well the “best fit” polynomial fits the acquired arrival time data sets. This paper outlines the mathematical details of the best fit polynomial where a Kalman filter formulation is implemented. The performance of the DSTPolyKF algorithm is demonstrated by processing real DST data sets.

Oct 1, 2022

By Eleonardo Lucas, Christ Barriga

The use of saline water, a product of the sea water osmosis process, for the processing of the mineral from the Bayovar Mine in Peru, is part of the process of final disposal of the studied tailings. In this sense, this paper presents an experimental program implemented for the correct evaluation of this fine low-density phosphate tailings, the behavior of six solids contents prepared in the laboratory with limits between the range 8.5% to 21% were analyzed. The results achieved, from settling and consolidation tests by hydraulic consolidation test, attested to the effectiveness, in addition to being representative, based on the analyzes and comparisons instituted and the definition of the compressibility and consolidation characteristics of the phosphate tailings of the evaluation.

Sep 30, 2022

By Abrahan Barriga

The present study demonstrates the feasibility of the ultrafine grinding and atmospheric leaching process applied to refractory gold concentrates from Salave Project located in northern Spain. At bench scale, it was found acceptable sulfide oxidation was about 84-85% and CIL gold recoveries between 95-96% applying specific energy consumption between 30 and 60 kWh/t during ultrafine grinding. The atmospheric oxidation of the sulfide concentrate was controlled between pH 4.4 and 4.8 with a mixture 90/10 of CaCO3/NaCO3 with residence time of 48 hours for the atmospheric oxidation and 30 hours residence time for the CIL process.

Sep 30, 2022

By Merrill Steve, Dabrowsli Bartosz, Law Harrison, Taggart Diane, Christodoulou Lance

The capability to enhance flotation performance is a continuous pursuit in the mineral processing industry. Incremental improvements are being pursued by incorporating design changes into established flotation technologies. The industry, however, is demanding advanced technologies to perform better in terms of improved resource utilization while at the same time ensuring that power and water usage is reduced. To meet these demands, it is necessary to make a step change in the performance capability of flotation equipment.

Sep 30, 2022

By Ian Coltrin, Steve Merrill, Dariusz Lelinski, Sudhir Kamath

Froth flotation has been the heart of mineral beneficiation for over a century. Over the years, developments have been made in flotation cell design, size, and in many other aspects of flotation technology. Despite the overall effectiveness of these improvements, valuable mineral particles are often lost along with waste material. These particles are lost when the froth recovery process within a flotation system is not designed for variable froth conditions seen in plant operations. Both the amount of froth generated and the type of froth in a flotation cell change as concentrate is removed down a row of cells. Traditionally, froth recovery has been designed using a froth carry rate averaged over the entire row of flotation cells with a static amount of open area at the top of the cell.

Sep 30, 2022

By Mauricio Estrada, Luis Vilchez, Luis Valencia, Marco Vera, Italo Manzo

Flotation is the most used separation process worldwide. Flotation characterization is usually carried out in batch conditions at laboratory scale. A phenomenological description of the flotation process is challenging, however, the evaluation of flotation performance in a contextual manner by means of a pilot plant is beneficial to reduce uncertainty on metallurgical results. In addition, leveraging pilot plant results by digitalize them helps describe the process dynamically. Consequently, flotation pilot plant testing allows a Digital Twin (DT) to be generated by combining ore characteristics, process information and a digital architectural platform. Therefore, the generation of a Digital Twin of the flotation pilot plant provides a tool to explore and evaluate new operating scenarios. This allows an optimum scenario to be identified and scaled up (i.e., industrial operation).

Sep 30, 2022

By Ken Rahal, Chris Braun

As head grades of mines around the world decline, generation of tailings is increasing. Along with the increased tailings generation, reduction in water availability, and recent tailings dame failures, are causing mining companies to look at different disposal methods. One of the methods that is gaining traction is filtered tailings. Filtered Tailings currently provides the greatest water recovery and the smallest footprint among all the tailings disposal methods. This paper will present two case studies that analyze the filter and air compressor costs associated with a change in the final cake moisture target (i.e. a change from 17-wt% to 15-wt% cake moisture), for a base metal mine and gold mine.

Sep 30, 2022

By Sivan Iswaran, Will McLean

This paper details a 2MLD ion exchange water treatment plant which selectively removes arsenic, antimony, iron, hardness, and sulphate from mining water; designed to meet environmental quality indicators such as sulphates. The client, Fosterville Gold Mine Pty Ltd, is owned by Kirkland Lake Gold and is one of the world’s highest grade gold mines. The site located near Melbourne, Australia had identified a risk of reduced mine water storage capacity due to surface run-off and increased sulphate rich dewatering of the underground mine at depth. Clean TeQ Water carried out the project management, process design, procurement, and commissioning for the plant, which was handed over in August 2020.

Sep 30, 2022

By Egonk Arriagada, Brindel Barzola, Peter Leckie, Greg Zwolak, Gilmar Guzmán, Germán Chen

Newmont’s Yanacocha operation in Peru presented an especially challenging environment for reliable cyanide measurement and control, processing 3 semi-distinct complex ore types with feed Cu ranging from below 250ppm (as CuCN) to more than 5000ppm, and feed S ranging from low to 5%, resulting in cyanide consumption from as low as 1.5 kg/t to as high as 3.1 kg/t, and gold recovery ranging from approximately 57% to about 78 % (average plant performance based on the type of ore). A literature search by the authors to identify a method for accurate cyanide determination that was also suitable for automation settled on the work of Breuer et al (2011) as a basis. Early challenges in adapting the laboratory technique for the ‘real solutions’ and the range of variability experienced in the plant are discussed, as are other operational challenges due to the complex and changing solution chemistry.

Sep 30, 2022

By Yohel Olortegui, Rolando Alvarado, Julio Sagua, José Lima

La planificación estratégica de una operación minera debe estar en constante evolución para hacer frente a escenarios cambiantes, y en ocasiones atípicos, como variaciones agresivas en el precio de los metales, tecnologías emergentes, modificaciones a estándares y normas legales para desarrollar el negocio minero, entre otras. Es entonces necesario implementar innovaciones revolucionarias, en lugar de solo mejoras constantes (Hammer, 2004). Lograr esta mencionada innovación operacional genera impactos de mayor magnitud en la cultura operativa, trayendo consigo la reducción de exposición a peligros, incremento en uso de energías limpias y reducción de huella de carbono, cambio en la estrategia de operación, reducción de costos operativos.

Sep 30, 2022

By Javier Illanes, Maurice Moore, Felipe Moroni, Rafael Acosta

Any organization that subjects its activities to a continuous improvement process must be able to adequately measure the results of the implemented changes in order to pursue better results over time. This is no different for mining companies. When it comes to blasting, an accurate fragmentation analysis can correlate blast design and rock mass parameters to particle size distribution, enabling us to further analyze the correspondence of specific design patterns, applied to specific rock mass properties and the result in measured fragmentation indicators, such as P80 and fines percentage.

Sep 30, 2022

By Pascual Perazzo Vaschetti Gabriella

The increasing emphasis on environmental issues has crucial importance in mining projects, hence in tailings dams. Their water barrier needs a two-fold environmental assessment: the environmental impact caused by construction activities, and the environmental impact over time. Unfortunately, tailings dams’ failures have great and long-lasting environmental consequences, and as mining sites become bigger and tailings dams higher, the risk of failures may increase. Furthermore, since these dams are mostly constructed over many years, design parameters/materials may change, the engineers may change, and since cost is a driving parameter, less attention may be given to quality control and monitoring. Geomembrane water barriers mitigate such impacts.

Sep 30, 2022

By Laurie McDonnell

As reserves of high-grade, easily accessible ores decline, it is becoming increasingly important to treat complex feeds and recover multiple target metals, and to identify approaches that will achieve this is a cost-effective manner. Hydrometallurgical treatment of sulphide based material allows for a balance between costs, recovery, and flexibility in final product selection. Glencore Technology’s hydrometallurgical solution to the treatment of sulphide ores is the Albion Process™, comprising two main steps. The first step involves ultra-fine grinding using the IsaMill™, which minimises the potential for passivation of the leaching sulphide and increases surface area for oxidation during the Albion Process™ leach. The second step is the oxidation of the finely ground sulphide concentrate utilising the HyperSparge™ for oxygen injection in Glencore Technology’s Oxidative Leach Reactors (OxiLeach™).

Sep 30, 2022

By Stefano Utili, Robert Pell, Nelson Morales, Cristobal Valderrama, Andrea Agosti, Guillermo Albornoz

The overall slope angle (OSA) of pit walls plays a crucial role in the financial return of open pit mines. The work showcases a novel design methodology where non-planar geotechnically optimal pit walls with an OSA steeper than what is used in current design practices are employed without compromising mine safety, i.e. the optimal profiles are featured by the same Factor of Safety (FoS) than their traditional design counterparts. In the current design practice, pit wall profiles are often designed to be planar in cross-section and the profile in between ramps especially tend to be defined by a constant inter-ramp angle.

Sep 30, 2022

By Stanko Nikolic, Oscar Mendoza, Christian Pasten, Stuart Nicol, Ben Hogg

ISASMELT™ technology is based on the use of an elegant furnace system design which uses submerged lance technology to provide highly efficient mixing and reaction of feed materials in a molten slag bath. Within Peru the ISASMELT™ technology has been applied to the Southern Copper Ilo Smelter, part of Grupo Mexico. Southern Copper selected the ideal technology to meet their sulphur capture and particulate emissions requirements whilst minimising capital and operating costs. The commissioning of the ISASMELT™ in 2007 marked the modernisation of the primary smelting section of their smelter, with traditional batch converters still used for the secondary smelting stage of the copper production flowsheet.

Sep 30, 2022

By Gökhan Çevikbilen, Ümit Karadoğan, Sevde Korkut, Berrak Teymur

This study proposes a methodology for dewatering of mine waste using a multistage process, combining geotextile tubes and anionic polyacrylamide (PAM), which accelerates the recycling process of water for aggregate mine waste facilities. For this purpose, waste from a rock quarry located in Istanbul was investigated. Flocculation tests revealed that the use of anionic PAM at an optimum dosage reduced sedimentation time and decreased turbidity. The compatibility of geotextiles and mine waste conditioned with different dosages of the effective PAM was evaluated by rapid dewatering tests, considering the water content of the filter cake, amount of infiltrated solid content, and rate of filtration. Geotextile dewatering tests were also performed on PAM-free and conditioned suspensions. The dewatering process was optimized by the use of a geotextile tube in two stages: (i) on the unconditioned suspension and (ii) on recovered PAM-conditioned leachate. Directing PAM-free non-hazardous soil-based material obtained in stage i to alternative beneficial uses is suggested, to minimize the volume of waste. Furthermore, recycling of the effluent obtained at the second stage of the proposed method will ensure more efficient water reuse

Sep 29, 2022

By José Maria Silva, Eugênio Oliveira, Ruberlan Silva, Thiago Souza, Lucas Reis, Lorena Guimarães, Matheus Bianchetti

Copper mine operations consistently generate a large quantity of tailings after their concentration processing. These tailings are either piled up or stored in a dam, where both alternatives of disposal lead to environmental impacts. The dam copper tailings have a huge potential for by-product production thus improving sustainability and profitability in industrial operations. This paper describes a study aiming at producing a magnetite pellet feed as a by-product from a dam chalcopyrite flotation tailings and generating free magnetite non-magnetic rougher tailings. The chemical assay and mineralogy analysis of dam copper flotation tailings indicate low Fe grade (6.34 wt%), high SiO2 grade (63.14 wt%), low magnetite (3.6 wt%), and high iron silicates content (22.72 wt%). The complex mineralogy of these tailings leads to the need of grinding the rougher magnetite pellet feed as fine as 80% of particles smaller than 20 μm ( P80) aiming at improving magnetite liberation. The proposed process route comprises a scalping screen, low field rougher, and cleaner magnetic separations using a drum magnetic separator (80 kA/m or 1000 Gauss), followed by silicates reverse cationic flotation as a recleaner step. With this process route, it was possible to produce a high-quality magnetite pellet feed reaching 68.00 wt% of Fe, 2.13 wt% of SiO2, 0.51 wt% of Al2O3, and 95.1 wt% of magnetite. The Blaine specific surface area was 2300 cm2/ g, being in the range recommended for pelletizing (1900 up to 3000 cm2/ g). The total mass, Fe, SiO2, Al2O3, and magnetite recoveries were 2.77%, 29.71%, 0.09%, 0.12%, and 73.17%, respectively. Most of the magnetite losses, around 20% of total magnetite fed, occurred in the oversize of the scalping screen. Additionally, it generated non-magnetic rougher tailings with less than 1.0 wt% of magnetite that could be used as by-products and reduced the amount of tailings disposal in a dam. This study contributes toward the sustainability of operation, minimizing tailings disposal.

Sep 28, 2022

By Shaoyang Yan, Xinming Chen, Huazhe Jiao, Huaibao Chu, Chang Wang

In terms of the technical problems of rib spalling in large mining height coal face, a long-distance advanced pre-grouting layer flexible reinforcement technology is proposed in this paper. Based on the mechanism and failure mode of rib spalling in the coal face, the mechanical properties of the aluminum plastic composite pipe were analyzed by using the tensile and compression experiment. The deformation and strength characteristics of “flexible pipe + grouting” specimens were studied by uniaxial compression test, splitting test, and shear test. The UDEC numerical simulation software was used to simulate the reinforcement effect of “flexible pipe + grouting” at different positions. Combined with the field application, the feasibility of long-distance advanced pre-grouting layer flexible reinforcement technology was verified. The test results show the following: The coal face has the characteristics of brittle and large deformation. The aluminum plastic composite pipe has the characteristics of good elongation and tensile strength, which can endure the large deformation of the coal face. The “flexible pipe + grouting” can improve the tensile and shear strength of coal. The UDEC numerical simulation analysis indicated that the grouting hole layout of “flexible pipe + grouting” has a significant difference in the reinforcement effect of the coal face. Compared with single row grouting reinforcement, the reinforcement effect of double row grouting holes 1.5 m and 3.0 m away from the roof is better. According to the field application, it is feasible to use aluminum plastic composite pipe as a flexible grouting pipe to reinforce coal seam with 80–100 m long-distance pre-grouting. Long-distance advanced pre-grouting layer flexible reinforcement technology can improve the daily production of coal and reduce the support cost of the coal face. As a new method of reinforcement, long-distance layered flexible reinforcement has a significant effect on the prevention and treatment of rib spalling in large mining height coal face.

Sep 27, 2022