Search Documents

By Roger A. Dworak

This report describes in detail the work done on the development of the Time Domain Reflectometry Microcomputer (TDRM). Modifications to the FMC-Model 302A Cable Fault Locator is described in Appendix D. The TDRM unit uses an 8080 microcomputer to accurately locate major faults in low capacitance cables to within ± 1 foot when properly calibrated. Major faults in high capacitance cables are usually located within ± 5 feet. The upper limits of fault detection are <1 kilohm shunt fault and >7 ohm series fault. In practice fault detection limits are reduced to <300 ohms shunt fault and >30 ohms series fault because of discontinuities caused by cable repair.

Jan 1, 1977

By Robert E. Wallhagen

This report describes the results of a four year investigation into improved face ventilation systems for underground coal mines. The objective was to experimentally determine configurations for a diffuser fan system and a water spray (spray fan) system which will provide a maximum reduction in face methane concentrations without causing an increase in methane concentrations at the operator&apos;s position. The experimental evaluation was performed in full scale mock-up mine entries, simulating continuous mining operations in both a six foot and four foot coal seam complete with normal ventilation, water sprays, and methane emission. A limited study was also performed to assess the effect of scrubber discharge location on methane concentrations in the face area. The results indicated that diffuser fan and spray fan systems that were designed to augment the natural airflow pattern in the entry could provide a factor of 3 to 5 reduction in average methane concentration at the face, compared to a mining machine with just conventional water sprays. The properly designed diffuser and spray fan systems also significantly reduced the total methane present in the entry. A properly designed dust scrubber discharge can reduce face methane levels by a factor of two.

Jan 1, 1977

By M. D. Aldridge

The results of designing, constructing, installing and operating a ventilation monitoring system throughout an entire commercial coal mine is presented. Measured parameters were airflow, methane, carbon monoxide, temperature, relative humidity and differential pressure. A central computer provided for automatic system operation. Preliminary tests of two remotely controlled ventilation regulators were performed in conjunction with the monitoring system.

Jan 1, 1977

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155, "Demonstrating the Noise Control of a Coal Preparation Plant." A Consolidation Coal Company coal preparation plant (the Georgetown Plant) was selected for demonstration of various noise control techniques and materials in a commercially operating plant. At the start of the project, the 1650 tons per hour (tph) plant was surveyed to document the existing sound levels and worker noise exposures. On the basis of the survey, individual noise sources were characterized and assigned priorities for treatment. Four categories of noise control treatments were installed in this plant: ? Resilient impact pads ? Curtains ? Chute liners ? Resilient screen decks. Currently (1977) available resilient impact pads and curtains were found to be suit-able for general use in coal preparation plants; in the Georgetown Plant, they provided significant noise reduction [6 to 10 dB(A)]. The overall performance of the chute liners which also provided useful noise reduction, was strongly dependent on the specific installation. Although the resilient screen decks have the potential for 7 to 9 dB(A) of coal/screen impact noise reduction, blinding and delamination (in composite decks) en-countered at the Georgetown Plant represented major design problems for these products. This program achieved noise reductions of up to 10 dB in various areas of the Georgetown Plant (within the restrictions imposed by the plant&apos;s operation) resulting in significant reduction in worker noise exposures.

Jan 1, 1977

The safety analysis of shaft-sinking operations included a review of accident reports from coal and metal-nonmetallic mine shaft-sinking projects in the United States, a review of foreign and domestic shaft laws, and discussions with shaft contractors and Federal mine inspectors. Accident data were studied to identify the most common and the most severe types of shaft accidents and to determine their immediate and contributing causes. Additional factors such as worker training and experience, equipment and sinking procedures, regulations and enforcement practices were also investigated to determine their impact on shaft safety. The results of the study are summarized in recommendations for improved training of shaft miners and clarification of Federal shaft-sinking regulations. A guide to assist mine inspectors in examining shaft-sinking projects is also included.

Jan 1, 1977

By William A. Hustrulid

A technical and economic evaluation of the potential for improving mining productivity through the use of underreamers in blastholes, specifically in relation to Minnesota taconite, Arizona surface copper and in situ mining operations is presented. Included are (1) a review of the drilling and blasting practices presently being used, (2) a discussion of current underreamer technology. (3) the presentation of a general economic cost model for underreaming, (4) the application of the model to surface taconite, surface copper and in situ mining, and (5) a summary discussion including required performance specifications, potential overall benefits, and recommendations for further development.

Jan 1, 1977

By Roy L. Soderberg

The Bureau of Mines has conducted substantial research on the design, construction, and operation of metal and nonmetal tailings ponds. This design guide, like related Bureau publications that preceded it, is produced to assist the industry in the management of mill tailings disposal. It covers the site selection, sampling, laboratory testing, design, construction, operation, and inspection of tailings embankments. The effects of environment, topography, and hydrogeology are also included, and various methods of stability analysis and factors affecting stability are reviewed. Because of the diversity of problems encountered in tailings embankments, specific solutions are not intended. The guide is, however, a useful checklist for designers, operators, and inspectors of this type of structure.

Jan 1, 1977

By Gordon R. Sima

The contract is concerned with feasibility studies, design and fabrication of a group of prototype hand-held test instruments and machine-mounted test instruments for measurement of electrical shock hazards of mining machines. An instrument for use in open pit mining machine ground wire verification was proposed, developed, built, and tested. This report presents the design and operational theory of the open pit instrument as well as information on the program to improve the original prototype hand-held machine-mounted test instruments.

Jan 1, 1977

By Walter W. Kaufman

The braking performance of underground, rubber-tired, non-coal mining vehicles is evaluated. Surveys of mining equipment and braking manufacturers and underground stopping tests are discussed as they relate to this evaluation. Stopping performance recommendations are included as well as related aspects of roadway construction and runaway vehicle protective devices.

Jan 1, 1977

By A. N. Baldwin

This report documents work performed under Bureau of Mines Contract J0265029 to study and develop two innovative mining systems: ? An underground auger capable of augering into the right and left ribs without repositioning the machine ? A conventional mining system employing recently developed innovative machinery. The report is separated into two volumes to document the two studies separately. Volume I describes work performed and the recommended concept for a bidirectional auger. Volume II describes the studies of mining equipment performance and mining plane developed to determine a conventional mining plan offering improved productivity.

Jan 1, 1977

By R. A. Strehlow

This is the final report for U.S. Bureau of Mines contract HO-122122, which was in effect from June 30, 1972 through January 4, 1976. The work resulted in the design and construction of a large laboratory scale coal dust burner and the use of this burner to study gaseous and coal dust flammability. A new technique for determining gas phase flammability was developed and the effect of solid and gaseous suppressants on the propagation of coal dust flames was studied. In addition, a technique for measuring the C/H ratio in the flame was developed and the C/H ratio that was measured in a coal dust flame on this burner showed that the burning process was preceeded by pyroysis of the coal dust. Both experimental and theoretical studies showed that radiative trans-port is very important to the propagation of a coal dust flame.

Jan 1, 1977

Explosives identification tagging refers to the addition to explosives, during manufacture, of coded microparticles that can survive detonation, be recovered and decoded, and allow the explosives to be identified and traced to the last legal possessor as a result of distribution records kept of the coded tagged explosives. This study seeks to prepare the way for National implementation of identification tagging of all dynamites and cap-sensitive slurries (also known as water gels) by resolving technical issues and by developing a plan for pilot testing of the program. It is presented in two volumes: Volume I, National Implementation Model, and Volume II, Pilot Test Plan.

Jan 1, 1977

By J. Bootle

Marrow vein deposits will continue to be an important source of valuable minerals. Productivity per manshift is not keeping pace with operating costs. Increased mechanization of stoping operations must be obtained to create greater productivity at a reduced cost per ton. This application of mechanization may be to either present methods or to newly developed concepts. The total mine unit operations will be effected by increased productivity. Two approaches to increasing the mechanization of narrow vein stoping were studied with the intention of increasing stope productivity and decreasing stoping costs. A method of bringing efficient rubber-tired equipment into narrow cut and fill stopes was designed. It proposes to provide stope access by way of a ramp constructed on the stope fill. Impact breaking equipment was studied and specific applications proposed.

Jan 1, 1977

By Sabri Ergun

Cost estimates and technical feasibility are compared for six chemical coal cleaning technologies. The comparison is based on conceptual application of the chemical cleaning methods for removal of pyritic and organic sulfur from a utility grade bituminous coal. The process layout includes receipt of 8,000 tpd ROM coal, fine coal pulverizing, desulfurization, and preparation of a compacted clean coal suitable for storage and shipment. The methods are: the Magnex iron pentacarbonyl process, the KVB dry oxidation process, the Battelle hydrothermal caustic leaching precess, the TRW Meyers ferric ion leaching process, the Ledgemont oxygen/water leaching process, and the Bureau of Mines/Energy Research and Development Administration air/water leaching process. Capital costs estimated for the desulfurization operation alone, scaled to 8,000 tpd, range between $14 MM and $122 MM, while estimated operating costs for desulfurization alone on the same scale of operation range between $7 and $17 per ton clean coal produced. Relatively little is known about the chemical cleaning of coal, and present cost estimates indicate that the method might not be competitive at its present state of development when used alone to clean utility grade coals for sulfur removal. The principal attractiveness of chemical coal cleaning lies in its potential for combination with physical cleaning to produce cost competitive compliance coals in a combined process with high-Btu yields.

Jan 1, 1977

By R. V. Ramani

In this the available information friction factors and leakage report, on characteristics are reviewed and summarized. The use of Penn State Mine Ventilation Simulator (Volumes II and III of the Final Report) to analyze the sensitivity of the ventilation system to the changes in leakage and friction factors is discussed with examples. In simple ventilation systems, the results of changes in leakage and friction factors can be easily solved and explained by the laws of air-flow. In complex systems, with fixed quantity branches and multiple sections, the effect of changes in leakage and friction factors cannot be generalized. This study points out the importance of good input data for obtaining reliable information from computer analyses and demonstrates the application of simulators to analyze the effectiveness of ventilation systems. An extensive bibliography on friction factors, leakage characteristics and ventilation economics is included.

Jan 1, 1977

By Joseph L. Jordan

Coal is essential to America?s future energy needs. To meet these needs mining methods must be safe, economical, and environmentally acceptable. Belt conveyor systems for coal haulage from surface mines offer great potential in this situation. The advantages over conventional truck haulage are particularly promising for area strip mines in western coal fields such as the Powder River Basin where relatively thick, flat-lying coal seams occur. The current demand for low-sulfur coal specifically emphasizes the need for better mining methods in these areas. Underspoil haulage is the term applied to transportation of coal from the pit to the surfate in area strip coal mines by belt conveyors in tunnels under the spoil. The advantages over trucks include lower manpower requirements, greater pit safety and efficiency, and improved reclamation procedure. This evaluation includes a comparison of total mining costs for truck haulage versus six variations of the underspoil haulage concept. The more efficient of these underspoil haulage systems have economic advantages over truck haulage which become more pronounced with deeper overburden, thicker coal, and higher annual production.

Jan 1, 1977

By R. S. Rosso

A program to investigate the effects of hardened washers on the uniformity of roof bolt tension and the resulting ground control in an underground mine was carried out. The complete roof bolt installation and roof bolt loads, mine convergence, and bed separation were monitored for a period of five months. The results show no evidence to support or refute the theory that mechanical roof bolts offer better support when they are installed with a high uniformity of tension. Also shown is the fact that if the bolts are installed with a maximum deviation from the mean torque of ±15% the addition of hardened washers significantly improved the uniformity of the installed tensions in the roof bolts.

Jan 1, 1977

These proceedings consist of an introduction, nine descriptive papers, and a summary. The first paper is an overview of the respirable dust research program, the second paper describes the Mining Enforcement and Safety Administration&apos;s proposed changes in the respirable dust enforcement program, and the third paper describes respirable dust measurement. The remaining papers, by Bureau and contractor personnel, describes methods of reducing the amount of respirable dust to which coal miners are exposed. Of the six methods of reducing exposure to respirable dust described, two are methods of preventing or reducing the amount of respirable dust raised during mining operations, two are methods of collecting or removing dust after it has been released into the mine atmosphere, 2nd two describe methods that are combinations of prevention and collecting .

Jan 1, 1977

By A. E. Kasten

The contract objective was to develop and test automatic fire control systems for large surface machinery in surface coal mines. The effort described by the report covers the period from 31 January 1977 to 11 November 1977 and accomplished the following tasks: ? Data accumulation, mainly from visits to the major manufacturers and mine sites. ? Hazard analysis of blast-hole drill, mining shovel, and dragline. ? Recommended design concepts for automatic fire control systems for each of these vehicles. ? Detail system designs for each of these vehicles. ? Procurement of prototype systems for the blast-hole drill and mining shovel. ? Installation of the prototype systems on machines at a surface mine and demonstra¬tion of performance by fire tests on the machines.

Jan 1, 1977

By John H. Johnson

A study of mine air quality was conducted using the latest advanced continuous monitoring instruments. An overview of the various interacting variables in the mine that affect air quality is presented. One effort involves the evaluation of portable instruments, the development of measurement techniques, sample analysis procedures and computer programs for statistical analysis of measurement data, and the application of the instruments and techniques to the measurement of the concentrations of CO, CO2, NO, NO2 and particulate matter in a lead and a copper underground mine. A second effort involves the first application of the Mine Air Monitoring Laboratory (MAML), a mobile trailer containing laboratory type instruments, sampling and data systems for the measurement of CO, CO2, NO, NO2 and particulate matter. The data from the MAML for blasting and for operating diesel equipment are analyzed and presented in various plots.

Jan 1, 1977