Search Documents

By Qingguo Xue, Jingsong Wang, Guang Wang, Yuanyuan Zhang

Due to complicated structure and composition of high-phosphorus iron ore, pure substances were used to simulate the chemical composition of high-phosphorus iron ore to study the reaction of fluorapatite at different temperatures and effect of additives. The gasification process of P during carbothermic reduction process was investigated using a quadrupole mass spectrometer gas analysis. It is found fluorapatite was reduced to phosphorus which diffused into iron and gas phase. From the gas analysis, it was observed that PO and P gas species were vaporized around 800 °C. As the reduction temperature increased, the diffusion of phosphorus into iron was enhanced. The presence of Ca(OH)2 as additives not only promoted the reduction of iron oxide, but also decreased the degree of fluorapatite reaction to inhibit P into iron.

Mar 1, 2018

By Lu-ming Zhao, Li Zhao, Yu Wang

In this paper, the change of crystallization rate, dendrite arm spacing and dendrite width of mold flux with various magnetic field conditions were studied by experiment. Having found that the crystallization ratio of mold flux increased from 33 to 96.6%, the dendrite arm spacing decreased from 72.47 to 38.02 lm, the dendrite width decreased from 48.47 to 27.02 lm while the magnetic field frequency (f) equaled to 8 Hz and its strength (B) increased from 0 to 30 mT. The crystallization ratio of the mold flux increased from 91.9 to 96.1%, the dendrite arm spacing decreased from 60.53 to 28.08 lm,the dendrite width decreased from 42.53 to 24.08 lm when B equaled to 20 mT and f increased from 6 to 12 Hz. However, the XRD analysis indicated that the phase types of the mold flux under the experimental conditions did not transform. Results showed that an alternating magnetic field can promote the crystallization of mold flux and refine grain structure.

Mar 1, 2018

By Zhengde Pang, Xue-wei Lv, Guibao Qiu, Chenguang Bai, Zhiming Yan

As a result of the consumption and the rising cost of raw materials for ironmaking, steel producers have increased their utilization of low-cost, low-grade raw materials such as high alumina iron ore. The effect of Al2O3 and the Al2O3/SiO2 ratio on the viscosity, surface tension and sulfide capacity of the CaO–SiO2–Al2O3–MgO–TiO2 blast furnace slag system were studied in the present work. At a fixed CaO/SiO2 ratio of 1.20, 9 mass pct MgO, and 1 mass pct TiO2, the viscosity increases with an increase in Al2O3 content at a range of 16–24 mass pct, and decreases when the Al2O3 is higher than 24 mass pct. Increasing Al2O3/SiO2 from 0.47 to 0.92 causes a slight decrease in viscosity of the slags and has an opposite effect when Al 2O3/SiO2 is more than 0.92. The surface tension increases with increasing Al2O3 content at a fixed Al2O3 content and Al2O3/SiO2 at a fixed CaO content. The desulfurizing capacity decreases with increasing of Al2O3 content, while increases with increasing Al2O3/SiO2 at a fixed CaO content.

Mar 1, 2018

By Chengyi Ding, Yangyang Xie, Xuewei Lv, Senwei Xuan, Chenguang Bai, Kai Tang, Gang Li

Dicalcium ferrite (2CaOFe2O3, C2F) is one of the most significant bonding phase of fluxed sinters. Reduction of C2F was investigated via thermal kinetics analysis. The isothermal reduction behavior of C2F by 30% H2 and 70% N2 at 1123 K (850 °C), 1173 K (900 °C), and 1223 K (950 °C) were discussed by thermogravimetric analysis in this paper. The results revealed that the C2F reduction was typical one-step reaction. The apparent activation energy of the C2F reduction was 27.40 kJ/mol. The rate-determining steps of the C2F reduction were the first inner gas diffusion, then the inner gas diffusion and interface chemical reaction mixed controlling. The ln-ln analysis implied that the C2F reduction was described by the Avrami–Erofeev (A-E) equation, thus appeared as a 2D A-E equation kinetics reaction.

Mar 1, 2018

By Qingyun Huang, Wei Lv, Junyi Xiang, Xuewei Lv, Chenguang Bai

The kinetics of iron leaching from ilmenite in hydrochloric acid solutions were investigated. The effects of pre-oxidation roasting, leaching temperature, and holding time on iron extraction rate were determined. The results obtained show that the extraction of iron is significantly enhanced by pre-oxidation roasting and increasing leaching temperature from 75 to 108 °C. The results of the kinetic analysis of the leaching data indicate that the reaction is controlled by diffusion through the product layer. The apparent activation energy for the extraction of iron has been calculated to be 62.5 and 55.1 kJ/mol for untreated and oxidized ilmenite, respectively.

Mar 1, 2018

By Lu-ming Zhao, Li Zhao, Yu Wang

Mould flux is a vital functional material which is based on silicate including flux and framework material. The effects of magnetic field intensity and frequency on viscosity of mould flux were tested by rotational viscosity tester and a measurement device for electromagnetic characteristics of mould flux viscosity under high temperature conditions. The results show that: with the magnetic field intensity rising (0 –30 mT), the viscosity of mould flux increases by 1.3–1.8 P. With the frequency rising (6–12 Hz), the viscosity of mould flux is increased by 1.2–1.4 P. When the binary basicity is 1.08, the viscous flow activation energy increases with the increase of the magnetic field intensity and frequency. It can be the main reason for the increase of mould flux viscosity that the electromagnetic forces disrupt the ordered structure of mould flux and make the ion migration rate increase.

Mar 1, 2018

By Djalma Souza, Felipe Perissé Duarte Lopes, Frederico Muylaert Margem, Sergio Neves Monteiro

The development of composite materials is a combination of distinct materials, with applications in various areas, such as: aerospace, automobile, etc. Regardingmechanicalresistance,composites reinforced with a dispersion phase in a fiber form is more relevant. The green idea is use composites with natural fibers instead offiberglass, especially in non-structural applications. The Fique fiber has occupying an important place at Colombian agricultural and agribusiness sectors. Epoxy matrix composites reinforced with 1–6 Fique fabric layers were tested and the results indicated that thetensile properties improve with increasing theamount of Fique fabric layers. The fiber/matrix interaction was analyzed by scanning electron microscopy.

Mar 1, 2018

By Donggen Fang, Liu Xuan, Jilai Xue

SiO2 and Al2O3 in the metallurgical slag of nickel laterite ore have great recycling values. In this work, Si and Al were extracted from the slag in NaOH based molten salts through alkali roasting and water leaching process for preparing zeolite materials. The extraction ratio of SiO2 increases with increased temperature and appropriately prolonged time, and more than 80% SiO2 can be recycled from the slag after roasting at 550°C. Si and Al from the slag are in the filtered liquor for producing zeolite materials, while Mg, Ca, Fe and other impurities remain in the leached residues. Adding Na2CO3 into the alkalin-slag roasting process can reduce the amount of pure NaOH used with minor decrease in extraction ratio of SiO2, while make better separation of Ca to avoid it getting into the filtered liquor. Adding Al2O3 into the alkalin roasting process can replace part of more expensive NaAlO2 addition that is required for preparing zeotite material, which may bring out a minor decrease in extraction ratio of SiO2 due to formation of NaAlSiO 4 in the filtered residues. Quality X zeolite and 4A zeolite materials can be made from the starting liquor containing Si and Al recycled from the laterite nickel slag through alkali roasting and water leaching process.

Mar 1, 2018

By Vahid Javaheri, David Porter, Tun Tun Nyo

A field emission scanning electron microscope equipped with EBSD has been employed to evaluate the role of 0.013 wt% Nb on the evolution of the microstructure and texture of a novel thermomechanically processed low-alloy, medium-carbon steel. Specimens were subjected to hot-rolling with a total reduction of 80%, four passes in the recrystallization regime and four passes below the non-recrystallization temperature. Immediately after rolling, the strips were quenched to 420 °C and subsequently cooled slowly in a furnace to simulate strip coiling with transformation of austenite to bainite. The results showed that Nb microalloying results in a finer microstructure with a sharper texture when compared to an identical steel but without Nb. In addition, analysis of the retained austenite texture indicated that the main bcc texture components are the product transformed brass and copper components in the parent austenite.

Mar 1, 2018

By Isadora Dias Perez, Monica M. Jimenez Correa, Jorge A. Soares Tenorio, Denise Crocce Romano Espinosa

The generation of mining waste has been the subject of environmental, economic and social concern. Alternative and sustainable methods of recycling metals technologies are desired. The present work focuses on the application of the ion exchange technique for the extraction of metals contained in a lateritic nickel mining effluent. The Purolite S950 chelating resin was used in the present work because it has the ability to adsorb transition metals present in an acidic solution. The experiments were carried out in a batch varying the pH in the range of 0.5–2.0. 1 g of resin was placed in contact with 50 mL of solution and stirred for 120 min at a speed of 200 rpm and temperature at 25 °C. The results demonstrated that the affinity of the resin varied with pH. The adsorbed metals were only copper, manganese, magnesium and zinc. The most extracted metal was copper, corresponding to 37%, when the solution was conditioned at pH 2.0.

Mar 1, 2018

By Thamyres C. Carvalho, Edemarino A. Hildebrando, Roberto F. Neves, Francisco R. Valenzuela-Diaz

Synthetic clays are an option of materials that can be modified to obtain better and specific properties when compared with natural clays. Although clays are found in nature, they have many disadvantages that limit the use of them, such as existence of impurities, and variations in composition. Therefore, the objective of this work was to obtain synthetic clay/polyester resin nanocomposites. To characterize the clay, we used X-ray Diffraction (XRD), Total Attenuated Reflection Spectroscopy in the Fourier Transform Infrared Region (ATR-FTIR) and Scanning Electron Microscope with Field Emission (FEG-SEM) methods and the nanocomposites were characterized by XRD and mechanical resistance to compression. The results show the purity of the clay and the time of synthesis is an important parameter for its crystallization process. The clay/polyester nanocomposites were obtained and showed an increase in the ductility.

Mar 1, 2018

By Helio Wiebeck, Vijay Rangari, Julyana Santana, Francisco Valenzuela-Díaz, Esperidiana Moura, Marcus Vinicius de S. Seixas

Closed-cell polyethylene (PE) foams have been extensively used in many applications such as packaging, transportation, sports, construction, and agriculture because of their variety of properties including light weight, chemical resistance, thermal and electrical insulation. The objective of this study is to evaluate the influence of electron-beamirradiation on the properties of LDPE/EPDMblend foams. The LDPE/EPDM blend (80/20 wt%) were prepared by melt extrusion, using a twin-screw extruder machine. The foam structure of LDPE/EPDM blends was obtained by melt extrusion process, using a special single screw for foaming with 1.5 wt% of foaming agent as blowing agent. The foam samples were irradiated by electron-beamat radiation dose of 25, 50, 75 and 100 kGy and submitted to heating in an oven at 100 °C. The specimen tests samples of irradiated and non-irradiated foams were submitted to mechanical tests, DSC, TG analysis and density measurement.

Mar 1, 2018

By Zhi Yang, Ahmad Ghahreman, Farzaneh Sadri

Impurity removal is a very important stage of the hydrometallurgical treatment of rare earth elements (REE) processing circuit, which is performed after water leaching of the acid baked REE concentrate. Lime neutralization has a high efficiency in removal of impurities and is the preferred process due to its economic advantage; however, the process has its own problems, such as the production of large volumes of gypsum and co-precipitation of REE with gypsum, i.e. REE loss. This work deals with the effect of several additives (cetryltrimethylammonium bromide (CTAB), polyvinylsulfonic acid (PVS) and polyacrylic acid (PAA)) on the uptake of REE by gypsum from synthesized acidic solutions. The main purpose of this study is to investigate the changes in the crystalline morphology of gypsum precipitated by the addition of crystal habit modifiers and to determine the crystal changes’ effects on the uptake of REE by gypsum. In this regard, different concentrations (0.2, 2 and 5 g L−1) of above-mentioned additives were studied at room temperature.

Mar 1, 2018

By Yuanbo Zhang, Zijian Su, Bingbing Liu, Guanghui Li, Manman Lu, Tao Jiang

Acid wastewater containing toxic metal ions has become increasingly important global environmental concern and lead (Pb) is one of the prime toxic heavy metal ions. Humic acid (HA), a kind of natural organic matter, has been proventohaveagreatadsorptioncapacityformetalcations(Pb2+,Cu2+,etc.).Our previous study has verified that HA has excellent adsorbing ability on vanadium titanium-bearing magnetite(VTM) particles. In this study, VTM-HA complex magneticparticles werepreparedfor removing Pb(II)fromacidwastewater,which could be easily recycled by magnetic separation. The effects of pH value, ionic strength and VTM-HA concentration on the removal ratio of Pb(II) were deter- mined by isothermal adsorption tests. The results indicated that Pb(II) adsorption was subject topHand ionic strength. When initial Pb(II) concentration is 100 mg/ L, the residual concentration and removal ratio of Pb(II) reach 0.17 mg/L and 99.83%, respectively, which are much lower than the discharge standard. (cid:1) (cid:1)

Mar 1, 2018

By Pedro Henrique L. M. Lopes, Édio Pereira Lima Jr., Fernanda Santos da Luz, Fábio de Oliveira Braga, Sergio Neves Monteiro

Several works have been dedicated to study the ballistic response of multilayered armor systems (MAS), including those using natural fiber composites as second layer. These composites disclosed good ballistic performance, having economic and environmental advantages. In the present work, the objective was to investigate the effect of areal densities of each MAS layer, in the overall performance of a MAS with an alumina ceramic front, a curaua fabric reinforced composite filling, and an aluminum alloy backing the target. Ballistic “backface signature” tests were conducted, varying the areal densities of the MAS layers according to a Box-Behnken design. The results showed a similar influence of the ceramic and aluminum layers in the MAS “backface signatures”, although deformation and failure mechanisms were significantly different. The composite also showed significant participation in the overall MAS performance. Since the composite is cheaper and lighter, a balance minimizing the other layers would be advantageous.

Mar 1, 2018

By Shengli Wu, Yuandong Pei, Zhixing Zhao, Shuhai Ou, Jiangshan Shi, Huaiying Ma, Jun Xiong

Spraying technology on sintering surface bed after ignition has become a hot research topic, with the purpose of achieving energy-saving, emission reduction and improvement of sintering indexes. In this paper spraying steam technology was researched from theory, experiment and practice. First of all, from the thermody- namic and kinetic analysis, the mechanism of sintering surface spraying steam was analyzed and its advantageous effect was con firmed. Based on this, sintering pot test and commercial trial were carried out respectively. The results shown that spraying steam is bene ficial for increasing coke combustion ef ficiency with improving CO 2/(CO+CO2) in the exhaust gas from 80% to about 85% level, through decreasing CO content of flue gas by more than 1000 –2000 ppm. There was a suitable spraying amount to improve the quality of the sinter, and the spraying position of the steam cannot be excessively front and rear. Due to the low steam pressure (1 kg) and temperature (about 100 °C) compared with industrial steam (3 kg and 130 °C, respectively), the sinter quality such as yield index was affected by spraying steam in sintering pot test to a certain extent, and proper spraying amount (0.008 m 3, 50 kg sinter) in sinter pot test is far smaller than application amount in commercial trial (2t/h). It is thought that suitable spraying steam parameters has a comprehensive effect of energy saving and quality improvement.

Mar 1, 2018

By Liugen Sun, Xingming Jiang, Weijiao Yang, Yihang Hu, Yongqiang Yang, Hua Wang

During the past decades, cyclone electrowinning (CE) has been regarded as a novel separation technology, which can be used for direct electrowinning of metals from low concentration solution. Recently, CE was proven effective for the treatment of antimonic gold concentrates. The experimental results of cyclone electrowinning of antimony show the current efficiency increases from 43.8 to 72.2% with the increasing current density (from 254.8 to 647.3 A/m2), and on the other hand, power consumption per ton antimony decreases from 6100 to 4200 kWh with the aforementioned increasing current density. The grade of the obtained cathode antimony could reach 98.6%. Compared with the traditional electrowinning using parallel-board electrodes, the economic profit of CE was 33.1% higher attributed to the high current efficiency of CE. In addition, CE could adapt to high current density. All these characteristics indicate the CE method can be implemented commercially for processing antimonic gold concentrates.

Mar 1, 2018

By Liguang Zhu, Yihua Han, Qingjun Zhang, Xiaoyan Wu, Pengcheng Xiao

The evolution of chemical composition, size, proportion, and morphology of the Al-Ti-Mg-O inclusions during the steelmaking process of Interstitial Free (IF) steel from the RH to the Continuous Casting (CC) slab were investigated by means of Auto-SEM. Results showed that many of Al2O3 and MgO-Al2O3 type inclusions are modified by TiOx, while most of their shapes are irregular due to the high melting temperature. The composition evolutions and melting characteristics of Al-Ti-Mg-O inclusions under different contents of [Al], [Ti] and [Mg] were estimated by using thermodynamic software Factsage 7.0. Results showed that estimated results are in good agreement with the analysis results of industrial samples. Both the Ti alloying and spontaneous enrichment would make a high Ti concentration environment that was in favor of the TiOx existence. Moreover, more TiOx component can modify MgO-Al2O3 spine inclusion into inclusions with a lower melting temperature.

Mar 1, 2018

By Matthew John M. Krane, Patrick E. Krane

This study examines the operations of the Cowper stoves attached to an iron blast furnace from a Second Law perspective. The exergetic efficiency of a 3-stove system operating at cyclic steady state is determined using a model accounting for the thermal, mechanical, and chemical flow exergies of the top gas and blast air, as well as the thermal exergy stored and released in the stoves. The analysis covers the heating and mixing of blast gas in one on-blast stove, and the combustion of top gas and its use to heat two on-gas stoves. The effect of different cycle times, and blast furnace operating conditions on the exergetic efficiency of the cycle is examined, and the optimal cycle time for different blast temperatures found. In addition, a study of the combustion parameters quantifies the advantages of using enriched oxygen in the combustors.

Mar 1, 2018

By Duclerc Fernandes Parra, Ademar B. Lugão, Nilton Lincopan, Fernanda Esposito, Vijaya Rangari

Polymeric hydrogels are natural or synthetic systems, which have gained interest due to their high biocompatibility with soft tissues. These types of hydrogels have been used for wound dressing as a drug delivery system. Here in this study the polymeric hydrogels based wound healing systems were prepared using poly (N-vinyl-2-pyrrolidone) (PVP), poly (ethylene glycol) (PEG), agar and neomycin drug followed by gamma irradiation to promote crosslinking and sterilization. The influence of irradiation process with 25 kGy dose was investigated. The gel fraction and maximum swelling were estimated using physicochemical methods and found about 95% gel fraction and 1100% swelling after 8 h of immersion. Neomycin released from hydrogel was carried out by Liquid Chromatography-Mass Spectrometry method and the drug concentration remained constant for 48 h. Hydrogel/neomycin exhibited antibacterial effects against Staphylococcus aureus. With these results, it can be inferred that hydrogel/neomycin is a suitable candidate for wound dressing.

Mar 1, 2018