Search Documents

By John P. Turner, Benjamin J. Turner

"This report describes a research project for evaluating the applicability of the widely accepted 80 percent criterion for elongation of ground anchors to anchors with unbonded lengths exceeding 100 feet. This issue is driven by several recent projects involving ground anchors for landslide stabilization in which a significant percentage of the anchors did not meet the criterion that requires measured elongation during proof load testing of at least 80 percent of the theoretical elastic elongation. The projects involved anchor unbonded lengths in the range of 85 to 220 feet, which is outside the range traditionally used in practice, although anchors of this length are being used more frequently for landslide stabilization. The principal objective of this research is to address whether the widely accepted criterion of 80 percent elongation is applicable for such applications, and whether other factors affect the ability of anchors to meet the criterion.Analytical methods for predicting transfer of load along the length of steel strand due to friction loss are used routinely in the prestressed concrete industry. These analytical expressions provide a rational framework for quantifying changes in load due to friction along the length of a ground anchor in terms of a ‘wobble coefficient’ (K) as defined in Aalami (2004). Values of the wobble coefficient for ground anchors can only be determined by back-calculating from load tests, i.e., fit the value of K to the appropriate analytical expression based on the known test load and measured percent elongation. The analytical basis is first developed and shown to provide a tool for evaluating results of anchor load tests to determine the magnitude of expected elongation as a function of unbonded length. Next, a database of anchor load tests is used to back-calculate values of K for anchors with unbonded lengths in the range typically used in geotechnical applications (< 100 feet). These values of K are then used to calculate expected friction loss for anchors with high unbonded lengths (100 to 250 feet) to evaluate whether the 80 percent criterion is reasonable."

Jan 1, 2017

By A. Pezzuto

"Pipes are used on mine sites in a variety of applications including transport of slurry, conveying clean and processing water, and in mine dewatering. Mine waters and slurries can cause pipe wear and failures via several mechanisms (or combinations thereof) such as abrasion, scaling, and corrosion. Polyethylene (PE) pipe materials have grown in popularity over the past several decades due to their chemical and mechanical properties (e.g., inertness, flexibility, relatively low density) and low cost. While PE is generally resistant to corrosion, it is subject to abrasion. To combat this, a novel, rubber-like liner is in development. In addition to comprehensive abrasion testing, however, the liner must be evaluated to see how it performs under other conditions. Here, a brief field study is described that tested PE pipes with the new liner against traditional PE pipes to specifically assess mineral scale buildup. The study was conducted in the Reiche Zeche study mine in Freiberg, Germany in six different locations with varying water qualities and flow conditions. INTRODUCTION Water and slurry conveyance are major operations on and around mine and mill sites, from mine dewatering, to tailings transport, to water treatment processes. Conveyance systems in such applications can include great lengths of pipe materials along with pumps and monitoring instruments, and thus represent significant capital investments. Due to the variability of the physical and chemical properties of water and slurries, pipe materials are subject to a wide range of conditions. These can cause pipe wear and eventually failure leading to serious economic, environmental and social, consequences. While pressure-induced pipe failures (e.g., ruptures or ""bursts”) can be immediate, most failure mechanisms involve gradual processes. Scaling and sedimentation can present major problems for pipe systems conveying highly mineralized waters. Sedimentation generally refers to the deposition of suspended solids, such as sand, clay, silt, or organic matter onto pipe surfaces. This phenomenon can occur due to a decrease in water velocity or particle collisions with the pipe wall. Scaling, on the other hand, commonly refers to the deposition of precipitated mineral salts (including oxides and hydroxides) onto pipe surfaces. Mine waters often have extremely high ion concentrations (i.e., high dissolved solids content) due to their interaction with enormous surface areas of minerals, which are exposed during mining and processing operations (Brown and Barley, 2002). As these waters are transported, slight changes in temperature, pressure or chemistry (e.g., pH or ORP) can cause instability with respect to ion solubility such that salt precipitation begins to occur. “Seed” crystals can rapidly grow and attach to pipes, either due to local surface phenomenon near the pipe wall (e.g., which can promote coagulation) or sedimentation of the precipitated solid. Whether due to suspended or precipitated solids, as the solids begin to stick to pipe walls, “aging” or hardening processes can commence; and the build-up of scale can become self-perpetuating as the scale itself provides an attractive “nucleus” for further attachment of particles or crystal growth (Muryanto et al., 2014). Over time, scale-buildup reduces the effective pipe diameter, which can ultimately result in decreased flow velocity, clogging and, in some instances, bursting (Dirany et al., 2016)."

Jan 1, 2017

By Robert Bachus, Jamey Rosen, Fabio Santillan, Georgette Hlepas

"A seepage barrier of length 4,800 feet and maximum depth 144 feet is being installed at Bolivar Dam in Ohio. This project is owned by the United States Army Corps of Engineers and contracted to Treviicos South. Many data types are being collected, synthesized and analyzed on a nearly real-time basis to monitor and track dam construction using several technologies including an enterprise relational database and web-based Geographical Information Systems. These data are being collected by both the owner and contractor and managed by the data subcontractor, Geosyntec Consultants. Each of the owner and contractor brings their own list of goals and desires to the data management program, and the subcontractor’s duty is to address these goals with minimal compromise by either party. The owner requires comprehensive, transparent and timely access to data in both “executive summary” and detailed formats. The contractor requires immediate analysis of disparate data to determine (for example) if a given excavation meets the specified tolerance and continuity requirements. This paper will describe the tools and methods used to store, analyze and visualize these data and discuss how each party’s needs were met in a collaborative system.INTRODUCTIONThe 4,800 foot long seepage barrier under construction at Bolivar Dam requires the collection, organization, and sharing of several types of data. These data include drawings and borehole logs that existed prior to construction; data collected during construction (seepage barrier panel composition and verticality data, slurry quality control and quality assurance data, grouting records, etc.); and instrumentation data collected and reviewed throughout and beyond construction. Each of these data streams require input and review from the Owner (United States Army Corps of Engineers (USACE), responsible for quality assurance and the ultimate consumer of the data), the Contractor (Treviicos South, responsible for the construction of the seepage barrier, its quality control and analysis of the data per the Contract Specifications), and the Data Management Subcontractor (Geosyntec Consultants, responsible for organizing and presenting the data to meet the needs of the Owner and Contractor). While all parties work with the same common goal, i.e.: producing a high quality product in an efficient manner making dam safety paramount during construction, and require immediate and comprehensive access to these data, the needs and desires of the parties differ. The challenge presented to the Data Management Subcontractor is to synthesize these data into a series of tools and reports that meet each of these needs."

Jan 1, 2017

By A. Navarra, F. Mucciardi, H. Marambio, R. Parra, F. Oyarzún

"Discrete event simulation (DES) is an appropriate framework for the plant-wide analysis of copper smelters. These smelters apply a common set of chemical reactions: copper-iron sulfides are blasted with oxygen-enriched air, sending the iron into a slag phase and the sulfur into the offgas. Moreover, conventional copper smelters exhibit similar operational dynamics: a smelting furnace operates continually, feeding into an alternating set of converters that produce batches of blister copper. The thermochemical and operational commonalities of copper smelters are integrated within the DES framework. This serves as a common basis to begin evaluating the system dynamics of individual smelters. For complex problems, the simulation framework should be developed in phases, incorporating feedback from different personnel who have complementary perspectives. Sample computations are provided in this paper based on the Hernán Videla Lira smelter, whose production is constrained by meteorological conditions. IntroductionWorld copper production is approximately 18.5 million t/y (Brininstool, 2015), worth $80 billion a year. Out of this total, 75 percent comes from the pyrometallurgical processing of sulfide minerals (Fig. 1), which occurs in copper smelters. The remaining 25 percent is from the hydrometallurgical treatment of oxides and complex ores (Rotuska and Chmielewski, 2008), which uses solvent extraction and electrowinning.The current paper describes the pyrometallurgical processing, recognizing that the underlying thermodynamics and kinetics are well known (Degterov and Pelton, 1999), with the notable exception of minor element transport, such as arsenic (As), antimony (Sb), bismuth (Bi), silver (Ag), gold (Au). The latter is an ongoing area of research, as smelters are faced with increasingly complex ores (Devia, Wilkomirsky and Parra, 2012; Swinbourne and Kho, 2012). This paper focuses on the system dynamics of copper smelter operations, which has received considerably less attention than the chemical thermodynamics and kinetics.Smelter engineers and managers may contribute to the sustainability of their plant by improving their understanding of operational system dynamics. Indeed, we have prompted smelter improvement projects (Navarra, 2016; Navarra et al., 2016; Navarra and Mendoza, 2013) simply by adapting methodologies that are commonly used in other sectors. These previous works incorporate principles from computer-integrated manufacturing (Groover, 2000) and theory of constraints (Dettmer, 2007), featuring the use of discrete event simulation (DES)."

Jan 1, 2017

By Yanchuan Li, Haifei Yao, Haiyan Wang

"Dust pollution is very serious in coal mining process, which is a great threat to the underground staff health and equipment and facilities safety. Coal seam water injection in mining process is an effective way to reduce coal mine dust concentration at the source. However, the effectiveness of water injection is limited in high-pressure and low-porosity coal seam. To improve the moisture content of coal seam, expand the wetting range and enhance the effect of dust reduction by water injection, the injectability and influencing factors of coal water injection are analyzed by numerical simulation method, and the sealing technology under high-pressure condition is studied. Then, according to the practical conditions of Tangkou coal mine, the parameters and process system of process system are designed, the effect of high-pressure water injection in coal seam was determined by testing water injection quantity, water increment and dust concentration. It is showed that the dust-removal rate of the high dust concentration operation such as falling coal and moving frame is 63.49% and 59.72%, the maximum dust-removal rate of multi-processes is 53%, which achieve a high level of application. The research results in this paper is of important theoretical and practical value to improve the water injection effect of high-pressure and low-porosity coal seam and improve the efficiency of dust removal in coal mining process.Introduction With the increasing of the depth and mechanization of coal mining, coal dust, the impact of ground pressure, ground temperature and other natural disasters continue to upgrade the harm degree (Wang 2011, Wu et al 2012), disaster incidents occur frequently, which seriouslythreaten the safe and efficient mining and the physical and mental health of underground staff. Coal seam water injection can effectively reduce the coal dust when coal crushing, prevent the impact of mine pressure, coal and gas outburst disasters, by increasing the thermal conductivity of coal, reduce coal temperature, and prevent spontaneous combustion of coal. In addition, coal seam water can soften the hard coal, so that speed up the recovery rate, improve coal production and efficiency (Wu et al 2008, Nie et al 2007). However, the coal seam in many mining area is with high-pressure and low-porosity feature, Coal joint cracks are not developed and relatively hard, water injection is difficult in these coal seams, then the desired disaster prevention effect cannot be achieved (Jin et al 2001, Zhao et al 2000). In this paper, the numerical simulation and field test methods are used to design the high-pressure and low-porosity coal seam water injection technology, so as to solve the difficult problem of coal dust control in high-pressure and low-porosity in deep well mining process."

Jan 1, 2017

By M. Epiney, A. Ghahreman, R. Kim1and

"In the presence of sulfidic refractory ores, increasing the dissolved oxygen (DO) concentration can positively affect the gold leaching rate. To identify the role of DO in gold cyanidation, electrochemical behavior was studied in the presence of 3 different ores. Sample 1 was a low sulfide pyrite ore, contained 5.14% pyrite, 0.19% galena and 3.09% S. Sample 2 was a pyriticore as well, contained more sulfide as 8.35% S, and 12.4% of pyrite. Sample 3 was a tailing of silicate gold ore, still containing75 g/tAu, 0.13% Pb and 0.18% S. Gold cyanidation kinetics were studied by cyclic voltammetry (CV) and chronoamperometry tests. With sample 1, the gold oxidation peak current density from CV curve was increased to 1.38mA/cm2under oxygen injection, while it was only 0.66 mA/cm2with air injection. From chronoamperometry test, the reaction rate was also faster under oxygen injection. Sample 2 showed similar behavior with sample 1, but the gold oxidation peaks higher than sample 1, i.e. 1.75 and 2.27 mA/cm2, under air and oxygen injection, respectively. However, it seemed that the gold oxidation was impeded by sulfide ions for a longer period. In the presence of sample 3, the gold oxidation peak was the highest among three ores –2.75mA/cm2under oxygen injection, because of its lowest sulfide content. However, from chronoamperometry test, it was also shown that the gold oxidation was impeded because of a significant amount of Pb in the ore sample.INTRODUCTIONIt is well known that gold is leached under oxidative condition (Marsden &House, 2006). Through the most representative and oldest gold leaching technique, cyanidation, more than 90% of gold can be selectively leached from an ore. According to Elsner’s equation, gold is leached in cyanide solution by forming cyanide complex [Au (CN)2–], and oxygen is consumed as an oxidant(Eq. 1)."

Jan 1, 2017

By D. Barber, A. D. Miller, P. A. Bray

The project was to develop an area within the existing West County Wastewater Treatment Plant which would enable the construction of a new Raw Wastewater Pump Station (RWPS) with a footprint of approximately 85 feet by 190 feet and a foundation depth of about 82 feet below grade and a new Short- Term Detention Basin (STDB) with a footprint of about 80 feet by 130 feet and a foundation depth that varied from approximately 3 to 24 feet below grade.. The excavation support system had to be designed to withstand both normal and the 100-year flood elevations. A Reinforced Soil-Cement Wall (RSW)was chosen to provide a hydraulic barrier which consisted of a single row of soil-cement elements installed along the perimeter of the area to be excavated. Steel wide flange beams were installed on 4 foot centers to support construction loads and be resistant to the lateral forces of the soil and hydrostatic pressures. The RSW was installed to a maximum depth of 104.5ft using a triple-auger drill rig with mixing paddles with a 2ft key into weathered shale providing a cutoff wall consisting of 53,150 square foot of treated soil. The project was to provide the initial design of the excavation support for the pumping station excavation support system and groundwater cutoff. There was 534 linear foot of soil-cement-bentonite wall installed and 106 - 80 foot long W21 x 121 wide flange beams installed on four foot centers into the alignment of the wall. Each element was drilled down into the weathered shale to obtain groundwater cutoff. Derek R. Guthrie Water Quality Treatment Center Pumping Package is the site for a new pumping station that will service Louisville, Kentucky residents. After unplanned long term exposure into the winter, the effects of freeze thaw cycles were evident.

Jan 1, 2017

By S. Kelebek, U. Demir, T. C. H. Richards, E. Koss

"Laboratory-scale tests were carried out to investigate the response of a high-grade (~143 g/tonne) well-liberated gold ore to flotation using two collector types. Octyl and amyl xanthates, representing conventional types of collectors, were tested against an n-octanoic and hexanoic acids under moderate and high redox potential conditions. The latter was based upon a suggestion in literature that monocarboxylic acids are able to adsorb onto the surface of gold at redox potentials near 600 mV (SCE). This investigation did not demonstrate that these carboxylic acids could function as collectors for gold in real ores. In fact, they appear to have slightly depressed gold. However, the results demonstrated that octyl and amyl xanthates acted as highly effective gold collectors for this ore and that an increase in the collector dosage led to an increase in recovery for all mean particle sizes. In some tests, gold recoveries of around 95% were attainable in concentrates with grades around 6 kg/tonne, indicating that xanthate flotation remains a viable means of concentrating gold even at coarse grain sizes. Various aspects of the process such as grade-recovery performance and recovery by size are discussed.INTRODUCTION Three methods are used for the recovery of gold in mineral processing, either alone or in combination: gravity concentration, cyanidation and flotation. Gold occurs as a by-product in some ores together with platinum group metals and as the primary metal in other ores in the form of native gold and electrum, which are alloys of gold, silver and minor amounts of copper. Flotation is a viable method for recovering liberated gold where the gold is visible under an optical microscope (greater than 1 µm in size) and where the attachment of gold grains is not prevented due to bubble loading by competing minerals. It is generally known that grains finer than 150 µm in size will float with most collectors."

Jan 1, 2017

By Gerald Verbeek, David Tara

"When selecting an impact hammer to drive a particular pile, the decision is often based on local experience. In those cases, the contractor falls back on previous experience or draws on the experience of the hammer manufacturer to select the hammer that will be able to do the job. Obviously, a more scientific approach would be to perform a pile driving simulation using one of several commercially available software packages (e.g., GRLWEAP, AllWavePDP or PDPWave).However, this type of analysis requires quite a bit more effort. First, an accurate model of the pile driving process has to be developed, which includes a model of the soil profile at the job site and input into the analysis program. Then, the model must be analyzed to assess whether the combination of hammer, pile and soil model work.Over the years, numerous individuals and organizations have tried to develop something that would fit nicely in between these approaches: something more advanced than a gut feeling yet something that could be done on the back of an envelope; in other words, a “Goldilocks” approach — not too simple, not too complex, but just right.Screening Tool CriteriaThe goals of the approach are twofold: (1) select the appropriate impact hammer to drive an open toe steel pipe or H-pile, and (2) then use the model for the subsequent high strain dynamic testing (HSDT). The Goldilocks approach centers around five different criteria.1. Maximum Driving StressTo minimize the risk of damage, the maximum driving stresses are generally limited to 80 to 90% of the yield stress (fy) of the steel section. This approach does not consider issues such as hammer alignment, initial imperfections, denting and/or elastic buckling, and pile material fatigue history. However, even when these issues are not applicable, limiting average stresses to 0.9fy or even 0.8fy does not necessarily mitigate the risk of pile damage (Mostafa, 2011)."

Jan 1, 2017

By C. Birch

"Mineral reserve statements as well as optimizing mine planning require a block model with grades for each mining block. A cut-off grade is determined by considering the mining costs as well as the expected revenue for each block. These grades are estimated using various techniques, but in reality there is uncertainty in the grade values. These uncertainties result in two types of error. A type I error is where material is classified as ore and mined, but the true value is below the cut-off grade and the material is therefore waste. This material constitutes dilution. The type II error is where material is estimated to be below the cut-off grade and is classified as waste, whereas the true grade is actually above the cut-off grade. This material is not mined and the value is lost.This research considers the value of the lost ore and the costs of dilution under various degrees of uncertainty. Simulation using @Risk and mixed integer linear programing (Excel Solver) is used in a financial optimizer model to maximize either profit or net present value. This is applied to four Witwatersrand tabular gold deposits to investigate the impact of block grade uncertainty on cut-off grades.When optimizing for profit, value may be added by adjusting the cutoff grade slightly downwards. When optimizing for NPV, value may be added by lowering the cut-off grade significantly for the lower discounting rates. At higher discount rates, the lowering of the cut-off grades should be reduced, and in some cases an increase in cut-off grade may be required. Each mine reacted differently to the optimization and thus there is no single rule that can be applied across all tabular Witwatersrand gold deposits."

Jan 1, 2017

By M. Z. Emad, M. U. Khan

"Coal mines opting for longwall mining or its variations rely on the main and tail gates for production. Stability of these entries or crosscuts is crucial in coal mining operations. Roof or strata failure can be fatal, may lead to property loss and delay in production. Failure of the gates depends upon many factors including the mining method, panel dimensions, pillar width, mine depth, caving rate, dimensions of gates and roof strength properties. In Pakistan coal is mined through a variation of longwall mining method with almost no mechanization while using timber as a primary support. Timber support as chock is very useful in coal mines especially in overhanging face. Similarly gate entries and coal faces are supported by chock supports throughout their length. In this paper the stability of the longwall gate is assessed for a typical coal mine in Pakistan by using finite element code. Numerical modelling considerations for gate entries are discussed. A model parametric study is performed for key factors. The results showed that the existing mining practice is not suitable and there is a need to review the mining approach. INTRODUCTION Main and tail gate entries leading to longwall mining panel play a crucial role in production cycle. Failure of any of these may lead to loss of life, property and production delays. The stability of gate entries depends primarily on the nature of loading and stresses incurred. It is relatively easier to assess the ground response to production for common longwall mining panel. In thin-seam coal mines the gate entries are generally supported throughout their length by timber made chock supports. The tailgates receive huge deformations and stresses during the mining and backfilling cycle. The chock supports are required to take care of rock falls leading to blockage of entries causing production delays and loss of capital. A number of supports are available for supporting the gate entries (Hoek and Brown 1980; Brady and Brown 1985). The support system can be selected based on load-deformation characteristics including the yielding behavior, pre- and post-yielding behavior (Barczak, 2003). The principal of support selection is that the support characteristics must match the ground response in order to maintain the gate entries (Mucho, et al., 1999). It has been observed that thin-seam mining (<1 m) is very challenging and it is necessary to develop an understanding of ground mechanics before the selection of an efficient support system Dolinar (2003). The chock supports have been tested for load-deformation characteristics in the laboratory (Barczak 2003). But the ground and support interaction, response and loads must be assessed for individual site. This can be accomplished by in-situ testing and observations at few locations. The generated data is generally insufficient for complete understanding. Numerical models can combine the data generated in the laboratory and on-site to fulfill the requirements."

Jan 1, 2017

By Z. Scopa, E. Tarshizi, R. Setterlind, L. Frost, R. Livernois

"THE MINES OF THE FUTURE The mines of the future present a host of challenges, which may appear exciting or daunting depending on one’s perspective. Whether some sectors of the public recognize it or not, the demand for raw resources is not going away any time soon. In fact, it is rising as global population grows, urbanizes and attempts to steadily increase quality of life. Yes, at the same time that much of the highly developed world is calling for greener goods, reduced consumption, and cleaner production, in other areas there are cries for clean water and sanitation, consistent energy supply, access to health care and education, personal security, and support for basic human rights. The balancing act for sustainable development of our global society is indeed precarious, and the mining community is necessarily a key player. Fortunately, many industry members have accepted this role and the responsibility to provide leadership and a solid foundation for progress. Looking ahead, we need new generations of leaders, many of whom will be mine engineers, which are ready to tackle all sorts of complex problems. There are tremendous needs just for technological innovations. Increasingly tough deposits will require that we continue to expand scale toward “super” pits and “deep” underground mining fully develop unconventional recovery techniques like in-situ leaching and gasification or deep-sea extraction, and seriously consider off-earth endeavors. Such work will take entirely autonomous equipment; novel separations, processing and recycling methods; and systems that can withstand extreme physical conditions – just to name a few. It will also take a level of systems integration never-before seen in our field, complete with big data issues, sophisticated analytics and modeling efforts, and cyber-security challenges. Moreover, increasingly complex environmental problems will require creative solutions. Addressing issues like pollution control across multiple media, emerging contaminants, optimal management of wastes, selective mining, and shared use of resources between mine operations and surrounding communities and ecosystems are among top priorities. Really, a complete paradigm shift must occur, such that our focus is on overall improvement of environmental conditions, rather than minimization of impacts. A similar shift will be required in the social realm. How can we make miners safer and healthier on-site and off? How can we contribute to communities such that they are better off, now and long-term, for having a mine next door? How can we help transform artisanal mining practices to also contribute to sustainable development? How can our work be a factor in increasing economic and political stability? How can we improve the public understanding of raw resources and the need for mining enterprises?"

Jan 1, 2017

By H. Pempel, J. Markowski, P. Ay

"Metal-coated thermoplastic parts find more and more functional and aesthetic applications in the interior and exterior of cars. The vapor-deposited or electroplated coatings are usually composed of a plurality of nickel- and chromium-containing layers, which are applied to copper-containing carrier layers on the polymers. Previously, recycling processes are mainly focussed at the recovery or thermal utilization of the plastics. Targeted and selective recycling of the metallic coatings is usually not carried out. Together with several SME, BTU developed a process, in which a complete and separate recovery of all components in high purity is possible with biotechnological methods. The bioleaching is carried out with iron and sulfur-oxidizing bacteria, especially Acidithiobacillus ferrooxidans. The copper-containing layers are dissolved in the solution; chromium- and nickel-containing particles are precipitated as solids. After the bioleaching, a mechanical separation of the individual metal-containing components and their separate workup are carried out. End-products are metallic copper, a nickel- and chromium-containing solid and the cleaned plastics. The bioleaching ensures a high purity of the end products. Through the use of bacteria, which are also found in nature, the process is environmentally friendly. Compared to chemical leaching using inorganic acids, considerably shorter leaching times can be achieved. In addition to the optimization of the leaching process, the R/D-project also includes the development and testing of the apparatus technology.INTRODUCTION The material complexity of many end-user products has increased in recent years, especially in the fields of electrical appliances, vehicle technology and medical technology. However, the demands on functionality, safety, comfort and energy efficiency still play a greater role in product design as factors such as sustainability and usability. For example, if a car still holds more than 70% of steel in the 1980s, a vehicle nowadays includes a larger proportion of a variety of difficultly separable plastics and composite materials, as well as complex metal composites. This relates in particular to composites made from such different materials as metals and plastics. The processing and recovery of the components of those complex material mixtures is difficult for recycling companies."

Jan 1, 2017

By C. Bergstrand

"Precipitation of gypsum and the formation of scale may pose a serious challenge in the leaching of several minerals. As an example, precipitated gypsum may form scale in the machines increasing the need for maintenance. Alternatively, it may encapsulate precious elements, i.e. gold and lower the recovery during subsequent leach processes. In this work we explore how different biopolymers modify the rheology of gypsum at three different pH levels at ambient and elevated temperatures. The ability to disperse gypsum vary with temperature, pH and biopolymer. It is also inversely related to the scaling potential. Measurements of the zeta potential as a function of increasing amounts of biopolymer reveals that the magnitude of the zeta potential changes in the presence of biopolymer, and so does the ability to disperse the gypsum suspension. Similar results with hematite will also be discussed. The methodology and results may aid in the selection of additives used in mineral processing applications where scale pose a problem.INTRODUCTION Processing of refractory gold ores normally involve either atmospheric or oxidation under pressure in order to convert sulfides to oxides (Weir, King, & Robinson, 1986; Weir, Robinson, & King, 1986). This conversion facilitates leaching of gold (and silver) in normal CIL processes. During oxidation, sulfides are converted to sulfates. Normally, there is an abundance of calcium ions in the process water, either released from the ore or added as lime to adjust pH for the CIL process. Precipitation of calcium sulfate, or other compounds (calcium carbonate, jarosite, hematite) is a way to remove gangue minerals from the solution entering the CIL circuit (Ji, King, Fleming, & Ferron, 2010). Precipitation may also cause challenges in the process as gold (or other valuable elements) may become encapsulated in gangue. (Beauchamp, Choung, & Xu, 2006). In addition to precipitation, the precipitated gangue minerals may solidify and form scale in the processing equipment. Recently, Lauten and Kluck (2016) found that dispersants used as scale inhibitors to prevent encapsulation of gypsum did not modify the solubility of gypsum. In the utilised model system, similar amounts of gypsum precipitated with and without dispersants. Instead, it was found that the dispersants evaluated as scale inhibitors reduced the yield stress of gypsum suspensions. The reduced yield stress was associated with a reduced tendency for gypsum particles to agglomerate and form scale."

Jan 1, 2017

By Sara Moshfeghi, Seyyed Majdeddin Mir Mohammad Hosseini, Abolfazl Eslami

"Due to variety of current pile bearing capacity methods based on the cone penetration test (CPT), for optimum design, it is necessary to evaluate the performance of such methods in different geotechnical conditions. Geotechnical databases including piling and in-situ testing records have been recognized as useful tools for analysis, design and economical construction. In order to evaluate pile bearing capacity methods, AUT-CPT&Pile database has been compiled including 450 full scale pile load tests and CPT sounding records. This database consists of different pile types with a relatively wide range of geometries and various soil conditions. Forty three records of piles driven in sand deposits were then employed to evaluate effects of ultimate capacity interpretation criteria from load displacement diagrams. The Davisson offset limit criterion, the Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter were compared to estimated capacities from ten CPT based design methods currently used in practice. The Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter lead to reasonable results, the Brinch Hansen 80% criterion showed less scatter. For evaluating the accuracy and the precision of CPT-based methods, the results were compared to estimated capacities. Results of comparison indicate that the CPT-based methods mainly predict the pile capacity withreasonable accuracy.INTRODUCTIONAmong the different approaches of estimating the pile bearing capacity, in-situ tests, especially, the cone penetration test (CPT) are favored due to the cone similarities with piles in modes of installation as well as fast and continuous profiling. This trend is practically well established where deep foundations are to be constructed in soft to medium subsoil deposits (Eslami and Fellenius, 1997; Mayne and Niazi, 2009).Employing different design methods results in a wide range of values which complicates the selection of an appropriate one to determine the pile bearing capacity. Several studies by Briuad and Tucker (1988), Eslami and Fellenius (1997), Abu Farsakh and Titi (2004), Schneider et al. (2008) and Eslami et al. (2011) confirm disparity of different design methods predictions. Thus, for optimum design, it is necessary to evaluate and compare the performance of current methods.Geotechnical databases are known as helpful tools in research and practical applications for optimizing analysis and design and are mainly used for management and interpretation of data, evaluation of design methods, calibrating LRFD or ASD design factors, etc. Pile lateral and axial load tests are examples of databases in geotechnical engineering. A summary of several CPT and pile load test databases is presented in Table 1."

Jan 1, 2017

By L. Wilfley, G. A. Calboreanu

"Wear resistant 25% Cr hard cast iron is a heterogeneous material containing 1,600 HV hard chromium carbides embedded into martensitic matrix. It is the most used cast alloy in wear operations of mining industry, chemical industry, fracking, etc. During the last decade the hard iron manufacturers increased wear resistance in the following ways: • Reduce / eliminate harmful retained austenite and chromium + carbon depleted areas especially within eutectic carbide cells. In Max5A the improved 25% Cr alloy brittle carbide eutectic cells are removed which increases toughness. • Delay delamination between chromium carbides and matrix particularly during sliding abrasion wear. Delamination commences at the weakest chromium carbide – matrix contact lines exposing chromium carbide to localized bending stresses which gradually chip carbides away. Once the chromium carbide base is removed accelerated wear degradation occurs. • Evenly randomize and avoid discontinuities in the chromium carbide network. When chromium carbides are perpendicularly positioned to the wear surface wear rate is minimized. On the contrary the highest wear rate takes place when 3D oriented chromium carbides are parallel with the wear surface. In this case chromium carbides cover top network discontinuities being just matrix supported which leads to rapid carbide cracking. The new hard iron discussed in this paper fulfils and exceeds the above requirements increasing the casting service life around 250% in various wear operations. Physical and mechanical properties of Max5A are compared with well manufactured Industry Standard 25% Cr hard iron. The paper presents practical accomplishments obtained in the USA, South America and India. INTRODUCTION The chemical composition of Max5A and Industry Standard 25% Cr are identical like specified by ASTM A532 Class III Type A requesting C = 2.0-3.3% and Cr = 23.0-30.0%. Manganese, silicon, nickel, molybdenum and copper contents are limited by maximum accepted quantities.[1] According to published data the eutectic chromium carbides chemical composition of 25% Cr hard iron is Cr = 54% and C = 8% which indicates strong depletion of chromium and carbon along chromium carbide - matrix interfaces. [2] The optimized Max5A microstructure has minimized retained austenite, is devoid of harmful carbide eutectic cells and has the most advantageous chromium carbide and secondary chromium carbide morphology. This favorable microstructure increases wear resistance, mechanical properties and corrosion resistance. The paper compares the Max5A microscopic features and mechanical – physical properties with similar properties of high quality Industry Standard 25% Cr."

Jan 1, 2017

By Gautam Benerjee, Veera Reddy Boothukuri, Bhattacharjee Ram Madhav, Panigrahi Durga Charan

"India’s tryst with mechanized longwall coal mining started with the introduction of the first self-advancing powered support longwall (PSLW) face at Moonidih Colliery of Jharia Coalfield in 1978 and at Godavarikhani (GDK)7 Incline of Singareni Collieries Company Limited (SCCL) in 1983. During the last 37 years, about 30 longwall units in Coal India, Ltd., (CIL) and 10 longwall units in SCCL have been introduced with powered roof supports of varying capacity, ranging from 280 to 800 tonnes, in many mines in India under varying geological and geotechnical conditions. The majority of the longwall faces in India have been worked under relatively shallow cover (up to 200m), and significant strata control problems have been encountered due to poor caveability of the roof, inadequate capacity of the supports, a lack of knowledge on longwall caving mechanisms, less than adequate strata monitoring systems, and the non-availability of quality spare parts, etc. This has resulted in structural damage to supports and increased downtime of the equipment, thereby making longwall mining in India a case of technology failure. Energy demand for a developing country like India with a population of 1.2 billion is huge, and the thrust on increasing coal production continues. However, the share of coal production from underground mines in India continues to decline (current share is around 6%) because of absence of successful mass production technology in underground coal mining. Under this backdrop, a high-capacity longwall with state-of-the-art technology was introduced in 2014 at Adriyala Longwall Project (ALP) of SCCL for the first time in Indian Coal Mining Industry. The first longwall panel (LWP) has been completed successfully. This paper highlights the major geotechnical challenges encountered during development of the longwall gate roads due to the presence of two overlying clay bands, significant in-situ horizontal stresses and the experience of using rigid (welded) steel wire mesh with resin-anchored roof bolts. Efforts have been made to analyze longwall weighting and caving behavior, such as main and periodic weightings, the effect of front and side abutment pressures, and the behavior of gate roadway support systems under immediate friable weak roof with overlying massive sandstone."

Jan 1, 2017

By J. R. Schafler, J. L. Brinkman

"The US coal mining industry has suffered a recent decline in profits caused by a combination of decline in commodity demand and more restrictive government regulation, forcing coal mining companies to cease production in numerous mines. A 40% decrease in the total number of coal mines occurred from 1994 to 2000. The number of mines remained relatively constant until 2008 when a change of government sparked a series of new environmental regulations which have contributed to another 15% decrease from 2008 to 2016. In contrast, production has only decreased by 3%, increasing from 1994 to 2008, and then decreasing since 2008. However, this value is skewed by large increases in sub-bituminous coal production and decreases in other coal ranks. Several aspects assist in executive decisions on mine longevity and economic worth. Studies of open source mine data collected by mandated government surveys coupled with commodity history can be used to find relationships between mine closures and these elements, which include statistics on production tonnage, seam height, coal rank, etc. This paper looks at coal mining trends since 1994 by comparing mine, market, and regulation factors that may influence mine closure. INTRODUCTION The US coal mining industry is currently experiencing a decline in both demand and commodity price while facing implementation of more stringent air and water pollution regulations. Company profits have decreased significantly, forcing several major companies to declare bankruptcy. The industry was required to adapt to survive. Many of these companies have adjusted by abandoning mines; the last two decades have seen a drastic decrease in the number of mines. To discover the primary causes of this downturn, three major aspects must be studied: properties of abandoned mines, commodity history, and regulatory impact. TRENDS SINCE 1994 Each year, US coal mines are required to submit data on a wide variety of categories to the Mine Safety and Health Administration (MSHA) and the US Energy Information Administration (EIA). This data includes administrative records, production values, and information regarding the attributes of the mined material and the mine itself. Each year since 1996, EIA has released a report summarizing the data from two years prior. Additionally, MSHA maintains a database containing a collection of all the most current data. These resources are the primary sources for the following figures."

Jan 1, 2017

By S. Nakamura, M. Takaoka, Y. Mizuno, T. Kusakabe

"Mercury is produced as a byproduct from gold mines and, historically, has been transferred to recyclers and used for various industrial processes and products. However, under the Minamata Convention on Mercury, adopted in 2013,the intentional use of mercury in processes or products will be minimized in the world. Surplus elemental mercury should be treated as a hazardous waste and consequently, should be converted to a more stable chemical form for long-term storage or permanent disposal. A stabilization method has been developed to react mercury and sulfur using a planetary ball mill. The planetary ball mill can produce high-energy conditions and enable samples to react within a short period of time. A series of tests has been conducted to confirm that mercury sulfide can be produced using a bench scale machine with 2400 mL pot. Under a suitable experimental condition with 25 mm ball diameter, 30%of ball filling rate and 1.05 of molar ratio of S/Hg, a powdered mercury sulfide product was successfully obtained in 60 minutes. The leach ability and atmospheric emission from the product was extremely low. This stabilization method would contribute to an environmentally sound mercury management strategy for the gold industry.INTRODUCTIONDue to its unique physical and chemical properties, mercury has numerous applications, including in industry and medicine. However, mercury and its compounds are highly toxic. For example, in Japan, methyl mercury in waste water caused Minamata disease in the 1950s, which affected large numbers of people (Minamata Disease Municipal Museum, 2001). In recent years, environmental pollution caused by emissions and releases of mercury into the atmosphere, waterbody and land by various emission sources such as coal fire plants, artisanal and small-scale gold mining (ASGM), non-ferrous metal industries, waste incinerations etc. has also become a significant problem. To protect human health and the environment from anthropogenic emissions and releases of mercury and its compounds, the Minamata Convention on Mercury was adopted in 2013(UNEP, 2013)Because ground gold ore typically contains mercury at 0 to 100 ppm, mercury is often produced as a byproduct from gold mines (UNEP, 2016). In gold mining operations, mercury can be released from the ore by roasting or by leaching in cyanide solutions and recovery onto activated carbon. According to Yanget al. (2016), 85.1%of mercury in a concentrate was vaporized during a roasting process. Both processes finally discharge elemental mercury as a byproduct. In the USA, more than 100 ton of mercury was discharged from large-scale and industrial gold mining (Miller, 2004)."

Jan 1, 2017

By F. Nava-Alonso, E. Pérez-García, A. Uribe-Salas, J. C. Fuentes-Aceituno, A. A. González-Ibarra, E. N. Castillo-Ventureño

"Precious metals cannot easily be recovered from tellurides by the standard cyanidation process. This work assesses the cyanidation of synthetic samples of precious metals tellurides and explores some alternatives for the leaching of these species (i.e. cyanidation in presence of lead nitrate and thiosulfate leaching). For this purpose, three chemical systems were studied: (1) cyanidation of silver telluride and the effect of lead (II) nitrate addition, (2) cyanidation at high alkalinity and high cyanide concentration of a gold-gold telluride sample containing tellurium and tellurium dioxide, and (3) thiosulfate leaching of silver telluride employing cupric sulfate as oxidant and EDTA as complexing agent for copper. Results showed that standard cyanidation dissolves 10.5% of silver from silver telluride in six hours, while with the addition of 100 mg/L lead increased the silver dissolution up to 100% in the same time. The standard cyanidation of the gold-gold telluride sample dissolves only metallic gold in six hours, while when cyanide concentration and pH were increased, gold and gold telluride were simultaneously dissolved. Finally, thiosulfate leaching dissolves 43.1% of silver from silver telluride in six hours.INTRODUCTION Precious metals tellurides are classified as refractory ores due to the difficulties associated with processing them by the standard cyanidation method. The increasing presence of gold/silver tellurides in some deposits around the world, specifically in Sonora, Mexico, requires new approaches to the cyanidation process, or the development of new leaching techniques. Treatments have been proposed for the recovery of gold and silver from their tellurides, including roasting, preoxidation, cyanidation with lead nitrate, and the use of leaching agents other than cyanide (Zhang, et al., 2010; Ellis and Deschenes, 2016). This work presents preliminary results of three options to recover precious metals from pure tellurides: the cyanidation of gold telluride at high cyanide concentration and high alkalinity, the addition of lead nitrate to the standard cyanidation process, and the use of sodium thiosulfate as leaching reagent."

Jan 1, 2017