Search Documents

By David R. Shields, Michael T. Bracher

"The $330 million (U.S.) Dana-Farber Cancer Institute’s Yawkey Center for Cancer Care (Yawkey Center) sits in the heart of Boston’s Longwood Medical Area. The Yawkey Center is a cutting-edge cancer care facility that houses Dana-Farber’s adult clinical care and clinical research programs. Standing 14 stories above grade, it includes 7 stories of underground parking extending 75 ft (23 m) below ground. The structure is on a 198 by 186 ft (60 by 57 m) site sandwiched between Dana-Farber’s 13-story Richard A. and Susan F. Smith Research Laboratories Building, the Medical Area Total Energy Plant (MATEP), Jimmy Fund Way, and Brookline Avenue, a busy four lane artery through the heart of the Longwood Medical Area. Together with Simon Design Engineering, the project structural engineer, GEI Consultants designed an innovative foundation and excavation support system to isolate the building from ground vibrations generated by the adjacent MATEP power plant. In effect, the Yawkey Center is a 21-story free-standing structure that starts 7 stories below grade.The MATEP facility provides power for 9 million sq ft (840,000 sq m) of occupied space in the medical area. There are six 32-cylinder diesel engine generators in the facility that produce low-frequency ground vibrations in the 10 Hz range, similar to the natural frequency of typical building elements. The resonant response of the Yawkey Center building structure to these ground vibrations would affect the performance of sensitive medical research equipment and cause an unacceptable environment for clinical care.The soil profile at the site consists of stiff clay, fine sand, glacial till, and bedrock consisting of hard metamorphosed conglomerate. In-situ measurements of ground vibrations performed in boreholes showed that there was little attenuation of the vibrations with depth in the soil layers overlying the bedrock, but the vibration amplitude in the bedrock was markedly lower than in the overlying soil. Based on this data, an innovative foundation system was designed to support the building on bedrock located up to 110 ft (34 m) below ground surface, while isolating it from the surrounding soil. This was done by physically separating the below-grade parking garage floors from the perimeter foundation walls to create a free-standing structure supported on the bedrock"

Jan 1, 2012

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

By Erik Westman

Few studies have been conducted regarding the location, movement, and relative magnitude of the rear abutment of a longwall coal mine. The rear abutment, or the abutment pressure arch in the gob area, is controlled primarily by the quality of pack of the gob; the more compacted the gob is, the larger the stress would be theoretically. While there is no definitive location for the rear abutment, early studies showed that it could be located as far back in the gob as 300 m (1,000 ft). Like the location of the rear abutment, there has been little research conducted and very few answers as to the exact magnitude of the rear abutment load. Due to the fact that the rear abutment has been studied considerably less than the front or side abutment, the need for further studies is evident. From a ground control standpoint, the location and magnitude of a rear abutment could reveal information on the caving process associated with longwall mining, such as when the initial cave could be expected to occur in future panels. Besides the possible importance of the rear abutment from a ground control perspective, evidence related to the longwall rear abutment could be vital from a ventilation standpoint. The peak rear abutment location could serve as an area for harmful gases, such as methane, to accumulate because forcing air through repacked rock is more difficult than through loose rock. The objective of this study is to determine whether passive seismic tomography could image the location, movement, and relative magnitude of the rear abutment as the longwall face retreated, in addition to the forward abutment and gob. The results of a passive seismic imaging study at a western US longwall show evidence for the location, movement, and relative magnitude of a rear abutment. A clear zone of highlystressed strata is shown where the forward abutment is expected and a low-velocity, damaged zone is shown behind the face where the gob is located. These two zones retreat with the face over a three-week period. In addition, the images show a return to stress levels behind the gob that are slightly higher than overburden stress levels, which is presumably the rear abutment. This occurs at a distance behind the face that is approximately the same as the face width for this mine. We can conclude that passive seismic imaging can be used to identify the location, movement, and relative magnitude of the rear abutment of a longwall mine. This conclusion is dependent on the use of appropriate data collection and processing methods. The information provided can benefit the both ground control and ventilation engineers as they strive to improve the safety and efficiency of longwall mines. The knowledge associated with the rear abutment of a longwall could not only help increase production through proper initial planning and reduce down time, but it could also make positive strides in improving the overall safety surrounding a longwall mining operation.

Jan 1, 2012

By R. Asmatulu

According to Darcy's law, the rate of filtration should increase with increasing pressure drop across a filter cake. In centrifugal filtration, the driving pressure is created by the centrifugal forces applied in the free water on the surface of a filter cake. However, the pressure drop can become negative when the free water surface disappears, which makes it difficult to achieve low cake moistures. In hyperbaric centrifugal filtration, this problem is overcome using air pressure to restore the pressure differential. In the present work, various mineral and coal fines have been subjected to hyperbaric centrifugal filtration tests. The laboratory tests show that the moistures of various mineral fines, such as copper and zinc concentrates, phosphate, talc, kaolin clay, and precipitated calcium carbonate, can be reduced substantially below that achieved by conventional centrifuges. Similar promising results have also been obtained with various coal fines in laboratory and pilot-scale test programs and in full-scale plant demonstrations.

Jan 1, 2012

By Q. G. Reynolds, R. T. Jones

"Residence time distributions are well defined for batch and continuously stirred reactors. However, there exist many smelting furnaces that do not fit either of these classifications. A mathematical description is presented for the case of a furnace that is fed continuously, but where the liquid slag and metallic products are tapped intermittently. The effects of slag and metal tapping intervals and the fraction of liquid retained in the furnace, are shown to have a significant effect on the residence time distribution.INTRODUCTIONThere are some processes in which the time spent by the feed material in a smelting furnace plays a significant role in determining the extent of the reactions between metal and slag and influences the degree of settling of metal droplets from a molten slag.Residence time distributions are well defined for batch and continuously stirred reactors. However, there exist many smelting furnaces that do not fit either of these classifications. Here we will focus on producing a mathematical description for the case of a furnace that is fed continuously, but where the liquid slag and metallic products are tapped intermittently. The effects of slag and metal tapping intervals and the fraction of liquid retained in the furnace, are studied.Previous work (Jones, la Grange and Assis, 1997) has studied the effect of retention time on the degree of cobalt recovery achieved in a slag reduction process. In that work, a method was proposed for the calculation of the mean residence time of the contents of a pilot-plant furnace. That approach is to be extended here for the purposes of providing a more general design or scale-up tool.The maximum allowable depth of molten material in a given furnace is affected by such factors as the desired batch size (or the size of the ladles) and the pressure of the molten material that the tap-hole and surrounding system can withstand. Within these constraints, there might be some scope for choice of taphole position. The effects of this choice need to be understood mathematically."

Jan 1, 2012

By Guolin Zheng, Tiejun Chun, Jian Pan, Deqing Zhu, Xianlin Zhou, Dong Chen

"The high temperature oxidizing-chloridizing roasting is one of useful methods to separate nonferrous metals from pyrite cinder and metallurgy slag. However, as one kind of main nonferrous metals in pyrite cinder and metallurgy slag, copper’s chlorination behavior is not demonstrated. In the present study, chlorination behaviors of CuO, Cu2O and CuS at the temperature range of 1025-1175 ? in air by simulating the chloridizing roasting process of pyrite cinder and metallurgy slag have been investigated. It is shown that Cu2O and CuS is much easier to remove, CuO is refractory to remove. In addition, the presence of SiO2 and CaO increases the Cu removal rate from CuO while the presence of SiO2, Al2O3, CaO and MgO decreases the Cu removal rate from Cu2O. Fe3O4 influences the Cu removal rate from CuO and Cu2O positively.IntroductionAs two kinds of significant secondary resources, pyrite cinder and metallurgy slag contain not only abundant iron but also considerable copper, lead, zinc etc. Millions of tons of pyrite cinder and metallurgy slag were discharged from nonferrous metal and chemical industries annually [1, 2] in China. The pyrite cinder and metallurgy slag are formed by roasting of minerals at a high temperature, so the properties of them are distinctly different from the natural iron ores, and the iron in them is closely associated with copper, lead, zinc and other nonferrous metals. High-quality pyrite cinder and metallurgy slag containing high iron and low impurities can hardly be obtained, leading to their low utilization degree [3]. Chlorination is characterized by the high reactivity of chloridion, the high volatility and low melting point of metal chlorides, and the big differences in the formation of metal chloride. Therefore, chlorination is widely applied in extraction metallurgy."

Jan 1, 2012

By Tiejun Chun, Jian Pan, Deqing Zhu, Zhiyong Ruan

"In this paper, the desulfuration of pyrite cinder pellets was carried out. Phase analysis shows that most sulfur of pyrite cinder exists in the form of elementary sulfur. Most sulfur was removed in preheating stage. 81.25% sulfur was removed and the average SO2 concentration of exhaust gas was 1365ppm when the pellets were preheated at 950oC for 9 min. The final product, assaying 62.42wt%Fe and 0.02wt%S content at 96.88% desulfuration was achieved under the conditions of preheating at 950? for 9 min and roasting at 1200? for 15 min, which can be used as the burden for blast furnace.IntroductionPyrite cinder, as a subsidiary product of sulfuric acid production by roasting of pyrite ores, was solid waste in sulfuric acid enterprises. According to the statistics, the annual production of pyrite cinder is about 15 million tons in China. Besides, there is lots of pyrite cinder deposited for many years [1-3]. The pyrite cinder consumed in the cement and other industries as auxiliary additives only accounts for less 30% of its total discharge and the left is stored in waste pond, occupying much land and polluting environment in China [4-5]. Moreover, pyrite cinder contains iron between 30-63% which can be utilized as a cheap raw material for ironmaking by sintering or pelletizing processes, which can not only prevent pollution but also provide cheap raw materials for ironmaking [6-7]. However, compared to traditional iron ore concentrate, pyrite cinder possesses higher sulfur content."

Jan 1, 2012

By George W. MacDonald

ALFRED NOBEL was born at Stockholm on October 21st. 1833, and died on December 10th, 1896. Although Sobrero’s discovery of nitroglycerin dated back to 1847, this explosive was manufactured on a commercial scale for the first time in 1862, by Nobel at a factory which he erected at Heleneborg, near Stockholm. These works were entirely wrecked by an explosion in 1864. In 1865, he erected works, which are still in existence, at Winterviken, near Stockholm. In 1864 Nobel introduced modifications in the manufacture of nitroglycerin which were the subject of a patent (see footnote No. 1), and at the same time, claimed a process for the detonation of nitroglycerin. Nobel states that, up to that time, the method used for the manufacture of nitroglycerin consisted in pouring glycerin, drop by drop, into a mixture of sulphuric acid and nitric acid contained in a refrigerating mixture. In order that the nitroglycerin should not be decomposed, the temperature was not allowed to rise above 0° C.

Jan 1, 2012

By E. Peek, L. Becze, K. Reading

"Gallium oxide is an important semiconductor material used in optoelectronic devices (flat panel and solar cell) catalysts and sensors. One of the methods to produce ?-Ga2O3 is the so-called hydrothermal route. It is practiced by Neo Gallium Compounds and comprises of two steps: (1) the production of mainly gallium-oxy-hydroxide in a pressure vessel by reacting metallic gallium with water at 200-220 ºC and (2) the calcination of gallium-oxy-hydroxide at 700-750 ºC to convert it into ?-Ga2O3. This paper describes this pressure hydrometallurgy process supported with relevant thermodynamic data and presents the characteristics of the ?-Ga2O3 powder produced for commercial purposes. INTRODUCTIONGallium is a relatively new metal, having been predicted by D. Mendeleev in 1871, discovered by P.E. Lecoq de Boisbaudran in 1875, and first commercially produced in the USA in 1943. Gallium is not rare, being more abundant in the earth crust than antimony, bismuth, molybdenum, silver and tungsten. However, few gallium minerals exist in nature, and the dispersion of gallium within other minerals add to the complexity of its recovery. In practice, gallium is found in dispersed state primarily in bauxites and in some sphalerites, and, to a much smaller extent, in some coals. At present, a very large proportion of the primary gallium in the world is recovered as a by-product of aluminum plants, mostly Bayer plants, where gallium is extracted from a bleed of the Bayer liquor (Roskill, 2011). In 2011, world production of primary gallium was estimated at 200 metric tonnes. In addition, there is a significant contribution of recycling to the overall yearly availability of the metal.Gallium exhibits fairly remarkable properties: it is liquid above 29.76 ºC, can be supercooled, and with its high boiling point (2204 ºC), is the metal with the widest liquid range. Gallium is magnetic, and is an excellent conductor of both heat and electricity. Gallium also displays a marked anisotropic electrical conductivity (Roskill, 2011). All these properties render gallium almost irreplaceable in the semiconductors (GaAs, GaN, GaSb, GaP wafers) and the optoelectronics industry (flat panel, solar cell)."

Jan 1, 2012

By Lijuan Li, Xin Xia, Junjun Huang, Qijie Zhai, Xiang Jiang

"Some experiments with different temperatures (1173, 1223, and l273K) and different annealing times (3, 4, 5, 6min) were carried out on cold-rolled plate of Fe-36Ni invar alloy. The microstructure and the mechanical properties were observed and tested respectively, and the fracture morphology was observed by SEM. The results show that with increasing of the temperature and the annealing time, the austenite grains gradually grow up accompanied by a small amount of annealing twin crystals, meanwhile, its plasticity and toughness are improved, and it is typical ductile fracture under the condition of tensile failure. After annealed at l223K, the invar alloy has better comprehensive properties than that at the other annealing temperatures, and the grains size is more uniform. Furthermore, when the annealing time is 4min, the invar alloy has the best comprehensive properties.IntroductionAs we known, most metals and alloys expand with increasing temperature. More than one hundred years ago (in 1897), Guillaume observed that Fe-Ni alloy with face-centered cubic (fcc) crystal structure, consisting of36%Ni, showing a very small thermal expansion coefficient below the ferro-to-paramagnetic transition, the thermal expansion coefficient around room temperature( <2 X 1O-6K-1 compared to most metallic materials which have a thermal expansion coefficient of 10-20 X 1O-6K-1) [1,2]. Since then, the subject has attracted many researchers, and various alloys with low thermal expansion coefficients have been developed. These alloys, generally known as ""invar alloys"", are in demand where dimensional changes due to variation in temperature must be minimized and where high stability is required [3, 4]."

Jan 1, 2012

By Allan Breitenbach

Leaching has been used since the 1600s on unlined ore dumps and since the late 1970s on lined leach pads for the recovery of metals from mined ore, the latter typically called ?heap? leaching and the former ?dump? leaching. Modern day run-of-mine (ROM) or crushed ore heaps are stacked in controlled lifts on lined leach pads and irrigated with a solvent solution (dilute alkaline cyanide for precious meals, dilute sulfuric acid for base metals and uranium). Conventional lined leach pads store process solutions and any storm water, snow melt and cumulative wet season surplus water by gravity flow to external ponds. Impounding valley leach pads (also known as valley fill heaps) differ from conventional leach pads by storing various combinations of process liquid solution and surplus water within internal ponds by using the interstitial pore volume of the ore. While impounding liquids within the heap is simple in concept, impounding leach pads are more complicated for construction and containment compared to conventional leach pads with external ponds.

Jan 1, 2012

By K. M. Murphy, M. B. Wittrup

ABSTRACT The Saskatchewan Ministry of Environment recognizes the importance of environmental protection as an important contributor to Saskatchewan’s economy, with the environmental performance of industry closely monitored. Unfortunately, environmental regulation is often accompanied by significant process that does not always add value to environmental protection activities. The Saskatchewan Ministry of Environment has embarked on a visionary restructuring of its regulatory framework from conventional command and control regulation to a results-based regulatory framework. This new regulatory framework will provide for establishing clear environmental protection and resource management objectives; streamlining the environmental acts and regulations; developing an environmental code of practice; relying on qualified persons; enhancing compliance and enforcement tools; eliminating of many permits; and developing greater certainty in environmental assessment decisions. Results-based regulation promises to deliver enhanced environmental protection with less process. The uranium industry in Saskatchewan will be used as an example of the potential effects of results-based regulation.

Jan 1, 2012

By J. Mothomogolo

Mining projects are capital-intensive and are also characterized by high technical and economic risks. These factors pose challenges to mining entrepreneurs when they seek to raise seed capital for mining start-ups. There are limited sources of mining investment funds in South Africa and each has shortcomings due to one reason or another. Another impediment is South Africa?s status as a developing economy, in which the standards of living ? which in turn influences the savings culture ? the limited GDPs and budget, the socio-political environment, and banking, mining, treasury and other regulations, determine the size of investments, particularly in mining ventures. The proposed funding mechanism was developed with the aim of filling the gaps identified in existing funding mechanisms that were developed by the government with the introduction of the Minerals and Petroleum Resources Development Act (MPRDA), 2002. The shortcomings identified were presented to the study participants as questions to obtain views that were used to define innovative ways of raising mining start-up capital. Most participants in the study supported the derived hypotheses and proposals, and these were used to refine the proposed mechanism for mining investment in South Africa. The proposed funding framework is aimed at encouraging interaction between mining entrepreneurs, government, and the investors to align goals and expectations when undertaking a mining investment.

Jan 1, 2012

By Enrique Munaretti, Vitor Rosenhaim, Jair Carlos Koppe, Joao Francisco Feijo

The B3 mine is a multiple coal seam strip mining in operation in Rio Grande do Sul, the southernmost state in Brazil. A traditional truck & excavator operation is used to remove the overburden and selectively mine coal seams, ranging in thickness from 30 cm (1 ft) to 2.5 m (8.2 ft). Blasting is required in order to excavate part of the sedimentary rock overburden where the rock is too hard for mechanical excavation, and to mine the coal seams, selectively.

Jan 1, 2012

By T. G. Joseph, A. Chamanara

ABSTRACT: The chicken and egg scenario — where adverse truck motions cause ground deterioration and poor ground profiles cause adverse truck motions — is a downward deterioration spiral dominating our industry. If we remove one action, the reaction stops. A simple truck to excavator load data analysis and wireless communication system is outlined, which will provide visual assistance to the excavator operator in achieving improved load placement and balance in a truck body. This will reduce subsequent hauler duty cycle adverse motions and g levels that contribute to structural fatigue, higher tkph, reduced tire life, and ongoing maintenance of haul roads.

Jan 1, 2012

By J. Talja

"Non-ferrous metal concentrates contain typically 7 – 12% water when received at the smelter. Removal of this water prior to smelting is always economically feasible because unnecessary heating of vapour (from 100 °C to 1200 °C) in the smelting furnace can thus be eliminated. This results in major reduction in CO2 emission and direct annual savings of several millions of dollars due to improved energy efficiency. Next step to further improve the energy efficiency, to gain substantial savings and simultaneously cut emissions is to select modern technology for the drying process. Consequently, all CO2 emission will be completely eliminated (from 40,000 tpy down to 0 tpy), NOx emission will be negligible, and the SO2 emission will be reduced by over 99 %. Switching of conventional direct heated drying technology to modern indirect steam drying brings, in addition to dramatic emission reduction, additional savings due to further improved energy efficiency. Direct energy savings count for 900 – 1300 MJ/t H2O, which depending on the concentrate feed rate and its moisture load can be worth several millions of dollars every year. Additional savings in operational expenses related to drying and gas cleaning may be worth a few million dollars more. Sustainability is a key issue today, and major savings together with significant emission reduction are readily available by proper technology selection for concentrate drying. INTRODUCTIONSustainability is a decisive principle in any process industry accompanied with emissions and high amount of energy. This is of significant importance in metal processing, including concentrate drying, where minimum impact on the environment, people and community are targeted, and all this with minimum cost, effort and resources. Therefore, special attention is paid to high energy efficiency, low energy consumption with preferable utilization of waste energy, safety issues, availability, level of maintenance, cost of maintenance, and emissions among other things.Non-ferrous metal concentrates can be dried using various techniques. Conventional drying based on direct heating, and use of fossil fuels for drying energy has almost entirely been replaced by steam drying. It is based on indirect heating and it has become the most dominant drying technology for copper concentrates during the last decade with over 90% of the market share of all new dryer installations. Among the steam dryers the Kumera Steam Dryer is the most pre-dominant technology with some 70% of all new dryer installations world-wide."

Jan 1, 2012

By W. Gabryk

A large new underground platinum mining project required that all different mining options were investigated during an option study before proceeding to the prefeasibility stage of the project. The capital project team identified 21 different options requiring investigation. These options considered 10 different access methods and 4 different mining methods. Each of the 21 options required a mine design, a valid production schedule, and the associated economics in order to facilitate a comparison on project Net Present Value (NPV) and other metrics. The project sponsors required this work to be completed in 3 months and therefore the project team decided to adopt an object-oriented modelling approach as implemented by Cyest Corporation. This would allow all 21 options to be valuated within the tight time frame due to the generation and re-use of templates. Standard objects were configured into templates containing the mine layout, design, and scheduling logic. These templates could then be assembled into a model to represent the option being investigated. The adoption of rules-based design and production scheduling then allowed for the rapid generation of a valid production schedule for each option with different iterations of varying production ramp-up and mining efficiency assumptions. The activity-based operating costs, labour, and capital were also linked to the standard templates such as a half level or barrel, which were then replicated to represent the overall mine structure for each option under consideration. Using this approach for each option, a full production schedule was produced per mining activity, the operating costs were calculated using activity-based costing, an infrastructure capital expenditure estimate was determined, the development capital requirements costed, and an overall NPV determined. This options study was completed in an unprecedented 10 weeks and a recommendation was put through to the Business to take three of the options to the next study phase.

Jan 1, 2012

By Yi Luo

Subsurface strata movements and deformations caused by longwall mining operations in underground coal mines could affect many important coal mining activities, such as gob well degasification, ground water protection and multiple seam mining. The stratifications in the overburden have significant influence on the subsurface and surface movements and deformations in the ground subsidence process. An enhanced subsurface subsidence prediction model considering overburden stratifications has been introduced in this paper. In this method, the entire overburden strata are equally divided into a finite number of layers and the percent of the hard rocks in each layer is an additional input. The proven influence function method is applied to predict the subsidence on each of the predefined layers progressively upward using the predicted subsidence on the previous layer as the subsidence cause for the current layer. A computer program is developed to facilitate the calculations. A case demonstration is used to show the applicability of the proposed subsurface subsidence prediction model.

Jan 1, 2012

By B. Yamamoto, D. Post, J. De Leon, A. Meike

"This paper describes the theory, design, building, and testing of the passive magnetic bearing stabilizing system which is the core of the passive magnetic bearing system. The stabilizing system is made up of two large magnetic disks opposing themselves with a stabilizing disk in the center which allows the system to self-locate in a null position without the need for external power sources or sensors. When outside forces act upon the stabilizer, the magnetic fields interact with the stabilizing plate to return the system to its null position. Collaboration between two industry leaders has allowed an actual prototype to be built and tested providing real data to prove out the theory.INTRODUCTIONMagnetic bearing/stabilizer systems have many advantages over conventional mechanical bearing systems. These include near-zero drag losses and no need for lubrication since the rotating elements make no mechanical contact with the stationary elements of the bearing system. However all magnetic bearing systems must contend with a constraint known as Earnshaw’s Theorem in the early 1800’s, this theorem asserts the impossibility of constructing a stable, non-contacting, electrostatic or magnetostatic levitation system using only fixed charges or fixed magnetic poles, such as those produced by permanent magnets. Because of the constraint imposed by Earnshaw’s Theorem virtually all present-day commercial magnetic bearing systems are of the “active” type. That is, they employ electromagnets that are powered by amplifiers the inputs to which come from sensors embedded in the bearing system. These sensors are a part of a feedback loop that operates to keep the levitated rotating parts of the bearing stable and centered. The resulting complexity means that active magnetic bearings are expensive, require periodic maintenance, and continuously consume electrical power to energize their amplifiers and their electromagnets.Passive magnetic bearings are, of course, also subject to the constraints imposed by Earnshaw’s Theorem but they solve this problem in a straightforward and simple way, with only “passive” elements that take advantage of a loophole implicit in the derivation of Earnshaw’s Theorem. This loophole is that Earnshaw’s Theorem as derived applies only to static systems, i.e. an assembly of stationary permanent magnets arranged so as to levitate an object containing other permanent magnets. The theorem can be overcome if dynamic effects are taken into account. In active magnetic bearings the “dynamic effects” involve the afore-mentioned sensors, amplifiers, and electromagnets."

Jan 1, 2012

By E. R. Weltevreden, C. Klauber, C. Vernon

"In this paper a review of the current status in recycling technologies for cathode ray tubes is given for both the glass and phosphors. Particular emphasis is placed on the opportunities for the recovery of the rare earth elements (REE) from the phosphor coatings. This is placed in the market context of alternative virgin sources and some of the advantages and disadvantages for REE waste recovery. Future opportunities are explored and also some experimental detail on a low cost leach system is presented. INTRODUCTIONThe disposal of cathode ray tube (CRT) based colour televisions has accelerated world-wide with the development of high definition flat screen panels. The total number of colour CRT televisions that have been sold in the United States in the mid-20th century is estimated to have been over 2 billion (U.S. Environmental Protection Agency, 2007), with high current rates of disposal. It is estimated that of the 20 million televisions annually discarded, 78% are send to landfill (Nnorom, Osibanjo & Ogwuegbu, 2011). However, this easily accessible item of electronics cannot only be turned into a valuable resource using the right recovery procedures, it can also prevent the substantial environmental contamination arising from improper disposal. In this review we focus on previous and current work performed on the recycling of CRT based televisions. Due to the increasing demand for rare earth metals, the main focus will be on the possibilities and challenges of recycling the fluorescent phosphor powders on the CRT’s panel glass.CATHODE RAY TUBE’S GLASS RECYCLINGConventional cathode ray tubes consist of three main parts, the panel, the funnel and the neck (Figure 1). To produce the different colours on the screen, the inside of the panel is coated with a matrix of hundreds of thousands of small phosphor dots. Each dot is one of three types of coloured phosphors, emitting either red, green or blue light. These emit light when excited by a beam of electrons generated by electron guns located in the neck of the CRT. These beams pass through holes in the shadow mask and excite the phosphor coating on the inside of the panel, to give light of variable RGB composition, see Figure 1."

Jan 1, 2012