Search Documents

By A. S. Ibrado, D. W. Fuerstenau

"Gold, silver and copper form various complexes with cyanide, of which only the singly charged dicyano form adsorbs appreciably on activated carbon. The adsorption of the dicyano complexes appears to be controlled predominantly by chemical reaction at the surface of a shrinking unreacted core. Metal uptake over time is non-linear, which eliminates control by boundary layer diffusion. The rate of adsorption is not enhanced by a reaction interruption, which suggests the absence of concentration gradients in the pores. Finally, the rate of adsorption increases with decreasing activated carbon size in a manner consistent with the shrinking core model. The results of this investigation accentuate the importance of efficient acid washing of carbon and removing carbon fines from the barren carbon stream. INTRODUCTION With the dwindling reserves of high-grade ores, most of the world’s gold is produced from low-grade ores by cyanide leaching. In the past, leaching was followed by the Merrill-Crowe process, in which gold is precipitated from clarified pregnant solutions by zinc cementation. This process is still being used for high-silver ores, where the cost of carbon stripping becomes prohibitive. For deposits with silver-to-gold ratios of about 4 or less, adsorption on activated carbon would be the usual solution purification step taken. The process simplifies solid-liquid separation and offers a viable solution to preg-robbing organic carbon in some ores. The modern industrial application of carbon adsorption started with the carbon-in-pulp (CIP) process, where carbon adsorption was used mainly as a solution purification step. In 1973, Homestake Mining Company commissioned the first large-scale CIP plant in the U.S.A.1 Later, carbon was added earlier in the circuit to control preg-robbing by adsorbing gold cyanide onto activated carbon as soon as it is dissolved. The scheme is successful because activated carbon is a stronger adsorber than the organic carbon found in preg-robbing ores. This process came to be known as the carbon-in-leach (CIL) process. Numerous research investigations have been performed on the chemistry involved in the CIP process, which at the time of its introduction was not clearly understood. Of these, research on the kinetics of adsorption probably bears the most immediate impact on industrial practice,2,3 where adsorption systems rarely reach equilibrium, if at all, and slight slowdowns in the adsorption rate can translate into significant decreases in revenue. To illustrate this, organic compounds, like flotation reagents, have been known to impair CIP circuits. However, laboratory tests showed that the organic compounds do not significantly affect the adsorption capacity of activated carbon. Rather, the harmful effect may be attributed to a lowered adsorption rate.4,5 Also well known is the faster rate at which fine activated carbon powders reach equilibrium compared to coarse activated carbon, even though the final (equilibrium) amount of material adsorbed per unit weight is the same."

Jan 1, 2015

By K. Bommer

"In today’s fast paced, globally competitive world, reliability and machine uptime are of the utmost importance to a successful operation. Along with these targets more emphasis is being put on cost reduction and decreasing the environmental impact of the overall system. To achieve these goals, automatic lubricators and lubrication systems have been used in many industries for years and are now becoming a common tool in the mining industry as well. These systems are able to provide proper lubrication amounts at the proper times autonomously, helping to keep the machines running smoothly while minimizing the physical support required. Copper mines in the southwest have begun utilizing auto lubrication to avoid mistakes and unplanned shut downs on critical equipment. This paper will describe the engineering behind these products and review case histories where these tools have been successfully utilized in the mining industry. INTRODUCTION In a dirty, dusty, wet environment, where machine uptime is imperative, proper lubrication of bearings is the only way to survive. With the push for cost reduction and mines striving to lower their environmental impact and increase worker safety according to MSHA guidelines, the old lubrication practices have come under scrutiny. It is no longer encouraged or cost effective to have maintenance personal walk from point to point throughout the entire mine pumping a shot of grease into each bearing once per shift. Automatic lubricators and lubrication systems have been on the market for years but recently, as the market focus has changed and technology has developed, the use of these systems has begun to rise in the mining industry. Automatic lubrication systems can be as simple as a single point lubricator lubricating one (1) bearing or a more complex system lubricating numerous bearings. With system design, the automatic lubricator provides a preset amount of grease to a bearing at regular, predetermined intervals. The systems designed to lubricate more than one bearing contain grease pumps of some design and possibly PLC controllers which can be used to remotely adjust and monitor the system. As can be seen in Figure 1, the right amount of lubrication can be achieved much more reliably with automatic lubricators. Depending on application needs, the market now has products to fit almost every wish list. This paper is going to focus on the single point systems that are lower in cost but are still being effective."

Jan 1, 2015

By Brian Danyliw

"Dust control is an increasingly important consideration for all mining operations from a health, safety, environmental and maintenance perspective. Modern mining operations incorporate a variety of mechanical dust control techniques into design however in many cases these engineered systems are unable to meet desired fugitive dust level targets. In these cases a variety of chemical dust suppression options are available to operators to assist in meeting their targets. This paper provides an overview of available chemistries, discussion of application techniques and equipment requirements and available performance monitoring technologies. This paper will also include a number of case histories discussing the treatment approach chosen, challenges encountered, chemical feed, storage and application equipment, monitoring techniques employed and results achieved.INTRODUCTIONDust FundamentalsFugitive dust by definition is an aerosol consisting of particulate matter suspended in a gaseous medium. Aerosols can include suspensions of particulate (solids) or sprays (liquids) or a mixture of both. Of particular concern from an occupational health and safety perspective are aerosols of particulate matter due to their involvement in classical occupations lung diseases such as silicosis, poisoning through chronic exposure to compounds such as lead and beryllium and expected involvement in more modern identified conditions such as cancer, asthma, and a host of other respiratory and non-respiratory conditions which may be caused or influenced through exposure to dust.According to the ""Glossary of Atmospheric Chemistry Terms"" (IUPAC, 1990), ""Dust: Small, dry, solid particles projected into the air by natural forces, such as wind, volcanic eruption, and by mechanical or man-made processes such as crushing, grinding, milling, drilling, demolition, shoveling, conveying, screening, bagging, and sweeping. Dust particles are usually in the size range from about 1 to 100 µm in diameter, and they settle slowly under the influence of gravity."" It should be noted that the behavior of particulates with respect to settling rate in air is a function of particle mass and shape and therefore the geometric size of the particle can be misleading. Occupational hygienists utilize the concept of particle aerodynamic diameter as a more representative reflection of particle size. Particle aerodynamic diameter, is defined as ""the diameter of a hypothetical sphere of density 1 g/cm3 having the same terminal settling velocity in calm air as the particle in question, regardless of its geometric size, shape and true density."" The expression of particle size as aerodynamic diameter allows for a more consistent understanding of particle behavior both from a settling perspective as well as from the perspective of how dust particles will behave in the respiratory tract. Figure 1 illustrates settling rates for particles of various aerodynamic diameters. The relationship between particle size and settling rate is important for understanding what size of particles must be addressed by dust control strategies as well as what particle sizes represent the most danger from an exposure and occupational health perspective."

Jan 1, 2015

By W. Beres

Many non-commercial operators are currently faced with the need to operate fleets of legacy gas turbine engines. How long such engines can be kept in service safely, without replacing a significant portion of their aging structural components, has become a growing concern to engine life-cycle managers, due to uncertainties in the remaining lives of critical components of these engines. This paper describes the application of the damage tolerance methodology to predict safe inspection intervals (SII) for critical components of gas turbine engines, using components of a turboprop engine for a transport aircraft as examples. High temperature components of this engine are made of advanced aerospace alloys. The methods of predicting three-dimensional fatigue crack growth at the critical location of turbine discs and spacers using both commercial and in-house developed algorithms are presented. Sensitivity analyses are performed to determine the effect of variations in material parameters on the predicted safe inspection intervals. In addition, spin rig tests performed for both turbine discs and spacers are described. Finally, crack growth rates predicted by numerical analyses are compared to those obtained from spin rig testing and the damage tolerance of the turbine components is assessed.

Jan 1, 2015

By John A. Davis, David W. Brunton

(Excerpts, pp 157-160) The usual means of firing blasting charges, especially in tunnels and adits in the Western States, is by the use of a safety fuse. The term safety fuse originated from the fact that when properly used under working conditions this fuse burns at a uniform rate and does not flash or explode, as was often the case with the means employed for igniting blasting charges previous to its invention; but the term is somewhat misleading, because the fuse is not, nor has it ever seriously been claimed to be, safe for use in gaseous coal mines. The fuse used for tunnel work is composed of a core of gunpowder surrounded by various layers of waterproofing material.

Jan 1, 2015

By Brian Wilson, Franz-Werner Gerressen

"Cutter Soil Mixing, also known as CSM, was developed in Europe as an alternate method of Deep Mixing to the more traditional single and multiple auger techniques, and brought to market by Bauer Maschinen GmbH (Bauer), towards the end of 2003. Initial development of the technique had been completed in a joint venture between Bauer and Bachy Soletanche. In 2004 the concept was introduced to the North American market. Continued development of the method and demonstration of its versatility, both in terms of applications and applicable soil types has seen a steady growth in the number of designs incorporating the approach, and contractors offering the technique. This paper provides a brief overview of the variety and size of projects and applications where the method has been adopted, discusses some lessons learned with respect to equipment operation as well as the improvements that have been introduced to the equipment, and briefly reviews the current state of practice, as well as some of the associated on-going research and development.BACKGROUNDCutter Soil Mixing (CSM) is a technique for deep soil mixing that was initially developed as a collaborative effort between Bauer Maschinen (Bauer) and Bachy Soletanche, but which ultimately resulted in the separate development of two somewhat different brands of CSM tool. The Bauer brand of CSM entered the European market in 2004, and was first promoted in the North American market in late 2004, with the first project starting in 2005. The Bachy Soletanche brand, sometimes referred to as “Geomix” was first marketed in Europe in 2005 and the first model introduced in North America in 2007.The development of the Cutter Soil Mixing technique utilized the experiences gained from Trench Cutter/Hydrofraise equipment, developing a technique that incorporates two cutting wheels rotating about a horizontal axis as opposed to the more conventional deep soil mixing approach which utilizes augers and mixing paddles rotating about vertical axes. Whereas the Trench Cutter/Hydrofraise technique excavates the soil from within a panel, and supports the open hole using a bentonite slurry, the CSM technique cuts and displaces the soil whilst pumping a slurry/grout directly into the soil through a port located between the wheels. The combination of cutting the soil while introducing an appropriate volume of slurry effectively fluidizes the column of soil around and above the cutter head. While this process achieves a high degree of mixing, even on the downward cutting stroke, thorough in-situ mixing typically occurs on the withdrawal stroke, when most of the slurry is added."

Jan 1, 2015

By J. H. van Laar, L. J. van der Walt, P. L. Crouse, H. Bissett, G. J. Puts

"SynopsisSilicon carbide nanopowders were produced using a microwave-induced plasma process operating at 15 kPa absolute and at atmospheric pressure. Methyltrichlorosilane (MTS) served as precursor, due to its advantageous stoichiometric silicon-to-carbon ratio of unity, allowing it to act as both carbon and silicon source. Argon served as carrier gas, and an additional hydrogen feed helped ensure a fully reducing reaction environment. The parameters under investigation were the H2:MTS molar ratio and the total enthalpy. The particle size distribution ranged from 20 nm upwards, as determined by SEM and TEM micrographs. It was found that an increase in enthalpy and a higher H2:MTS ratio resulted in smaller SiC particle sizes. The adhesion of particles was a common occurrence during the process, resulting in larger agglomerate sizes. SiC layers were deposited at 15 kPa with thicknesses ranging from 5.8 to 15 µm.IntroductionIt is well known that methyltrichlorosilane (CH3SiCl3 or MTS) decomposes to form silicon carbide (SiC) and hydrogen chloride (HCl) as shown in Equation [1]. The reaction kinetics and mechanisms for this reaction are thoroughly reported in the literature (Sone et al., 2000; Papasouliotis and Sotirchos, 1999; Kaneko et al., 2002; Wang et al., 2011)."

Jan 1, 2015

By Alberto Carmona Rosell, Sri Ram Ramankutty

"The installation of Bored Piles and Diaphragm Wall under slurry using tremie raises quality concerns on the integrity of concrete. It is vital to understand the effects on concrete integrity during concrete pouring process. This paper intends to unveil to what extent the compressive strength of the concrete pour is affected in contact with drilling fluid still. Another important angle of analysis proves whether the inclusion of solids particles of un-hydrated fluid could have impact on the concrete compressive strength. The testing comparing the response of concrete compressive strength when drilling fluid is included into the concrete mix altering the water/cement ratio by 5%, 20% and 30%. Comparative results are analysed between two different hydrated slurries namely sodium activated Bentonite and 3rd generation synthetic polymer.1. INTRODUCTIONSoil stabilization is the base for a successful deep foundation execution. The G3 System Slurry developed by Ground Engineering Operations (GEO), with its third generation polymer, namely PolyMud®, is an innovative and unique alternative to the mineral based slurries for soil stabilization, enhancing the quality and integrity of the underground foundation structures. It optimises the production rate of work progress and cost as well. At the same time, PolyMud® slurry is proven to be environmentally friendly.Guaranteeing the maximum quality of the foundation elements according to the initial design is one of the most important objectives and a concern for the foundations contractors. In order to fulfil the project expectations in this aspect, any incident that could compromise the designed concrete integrity and capacity must be avoided.GEO, has carry out its own research regarding effects on the concrete compression results if drilling fluid intermixes with fresh concrete while pouring. To shed light in this regard, GEO, in collaboration with CML (Concrete Materials Laboratory) Sdn. Bhd., carried out empiric tests that analyse this particular event from different perspectives, bringing up the corresponding results that will be studied and commented in this article."

Jan 1, 2015

By Alessandro Navarra, Roberto Parra, Boyd Davis, Frank Mucciardi

A smelter scheduling algorithm has been developed, which allocates the oxygen production between the smelting furnace and the converter aisle, so as to maximize copper throughput. The algorithm is intended for daily operation planning, controlling the sequencing of the converter cycles, and the oxygen drawn by these cycles. In some cases, it may be worthwhile to decrease converter oxygen allocation in favour of the smelting furnaces. Thus, a better utilization of the oxygen plant can increase primary copper throughput by several percentage points. This principle is demonstrated through sample computations. The approach presented in this paper can be incorporated into smelter management software.

Jan 1, 2015

By K R. Brentley

"Tshepong Mine, Harmony’s largest gold producing mine, is situated in the Free State portion of the Witwatersrand Basin, east of Odendaalsrus and north of Welkom, South Africa. The Basal reef is a narrow tabular conglomerate and is the main gold bearing ore body. The strata strikes mainly in a northsouth direction with an average dip of 22 degrees. Currently mining takes place at depths of between 1 690m and 2 150m below surface. The Basal reef unit consists of a conglomerate ranging between a few and 30cm in thickness. Some 80-90% of the gold occurs in the lower portion of the conglomerate. Directly above the conglomerate is a quartzite placer unit, the Basal quartzite, which is a clean, hard competent rock and varies in thickness between 50cm and 200cm. The Basal unit is overlain by the Khaki shale which can vary between 30cm and 500cm in width. It is weak and incompetent khaki coloured chloritic shale.A method of stoping, termed “undercut”, is practiced in order to remove the lower 15-20cm of the gold rich strata. The method entails removing this portion along with some 70-80cm of footwall host rock which is a strong competent quartzite. The hard competent quartzite overlying the conglomerate is left in-situ to form a competent hangingwall which can stabilize and prevent exposure of the weak Khakishale. This method of extraction was developed through trial and error and has been used reasonably successfully since its inception in the early 1960’s where the method was developed to extract the Basal reef at the Western Holdings Mines. Recently prospect drilling and a number of localised hangingwall failures indicated that the residual quartzite beam could be less than 60cm and in some instances as thin as 30cm in certain areas of the mine. The result of this is a less stable hangingwall which not only poses a safety risk to workers in these areas but also had the potential of locking up some 840 000 Tonnes of gold bearing ore. At the present gold price this amounts to revenue of approximately ZAR1.5 billion (U.S. $143 million).This paper discusses the method of “undercut stoping” and existing practices in place at Tshepong Mine. It also explores new initiatives such as the use of a simple freely-supported elastic beam solution to perform back analysis, on-site data capturing of beam thickness and support geometries in order to develop empirical design charts and numerical modelling to assist in the verification of the empirical design method."

Jan 1, 2015

By C. Samuelsson, H. Ahmed, B Björkman, A. Andersson

The cost of raw material and energy is a continuing driving force towards working with increasing the recycling of ore based steelmaking residues. In Sweden no on-site sinter plants are operated at the integrated steelworks. Instead, selected residues from the plant are incorporated in a cold bonded briquette product which is recycled to the process via the blast furnace (BF). Since the BF sludge is the major bleed of zinc out of the furnace it is required to be de-zinced prior to recycling in the briquette product. In the present work landfilled BF sludge has been characterized with respect to chemical composition, particle size distribution, X-ray diffraction (XRD), and scanning electron microscopy (SEM). The sludge was also subjected to laboratory scale hydrocyclone trials aiming at reducing the zinc content making the sludge viable for recycling. The results suggested that the sludge had been agglomerated prior to the characterization and hydrocyclone treatment. The zinc removal using the hydrocyclone was discussed.

Jan 1, 2015

By V. Labiouse, F. Orellana

"Hollow cylinder samples can be tested for both the characterization of rock properties and the physical modelling at reduced scale of engineering applications. Particularly, this type of experimental setup can be used to simulate different stress conditions around underground openings, as already developed in the petroleum engineering field e.g. to study the instabilities around deep wellbores during either drilling or the oil production phase. Some authors have also used this technique to successfully characterize the damaged zone around underground openings in the tunneling engineering field looking for an efficient design of their support.This article presents a new hollow cylinder testing device developed at the Rock Mechanics Laboratory of the Ecole Polytechnique Fédérale de Lausanne (EPFL), Switzerland. It allows a full and independent control of the confining pressure and pore water pressure conditions at both the inner and outer boundaries of Thick-Walled Hollow Cylindrical samples. In order to mimicking a tunnel excavation in a porous rock mass, after initial recovery of the in-situ stress and pore water pressure, the hollow cylinders are subjected to a decrease in the internal confining pressure. Moreover, X-Ray Computed Tomography scans of the specimens are performed through the testing cell before and after the mechanical unloading to monitor the displacements undergone and the sample damage. The equipment, testing procedure and data analysis techniques are briefly presented in the paper.The good performance of the apparatus has already been checked on weak rock specimens, among others on Boom and Opalinus Clay samples. In many configurations, the mechanical unloading is found to induce a Damaged Zone (DZ) around the central hole. Its geometry and extent show a great similarity with in-situ observations around tunnels driven in the Boom and Opalinus Clay formations. Such similarities contribute to increase confidence in the understanding and modelling of the ongoing processes."

Jan 1, 2015

By S. Bhattacharjee

"Rock failure process is generally recorded or measured using conventional sensors like strain gauges, seismic, micro-seismic, acoustic, electromagnetic and other techniques. The above sensors are either to be pasted on the surface of the rock sample or placed very near to it to capture the response of the sample with the increment of load. This requires precise tools to cut or polish the locations where sensors are to be placed. Moreover, deformation or acoustic or micro-seismic activities are recorded only at the locations where sensors are pasted.Recent development in Digital Image Correlation (DIC) technique has shown promise to measure deformation / strain at every location of the surface of a sample. In DIC, two images (reference and deformed) are taken within a small time interval of the same object are compared to estimate the change in reflectance as a function of displacement, velocity or rate of strain at each pixel while the object is undergoing through a loading process. In this study, extended digital image correlation (X-DIC) technique has been implemented using 4-noded quadrilateral elements with a discontinuity surface in the deformed image. The continuous and enriched displacements are estimated at each node.The X-DIC method is verified using numerically generated images. The study has been further extended to evaluate the performance of X-DIC method on deformation analysis of experimental samples under uni-axial loading condition. The results of this study show that X-DIC method is an effective tool for determination of displacements of the entire surface of a rock sample having a discrete crack or discontinuity in a non-contact manner. This method demonstrates the applicability to investigate rock failure mechanism for the entire sample in a laboratory set up as well as monitoring of pillar failure mechanism in underground mines."

Jan 1, 2015

By N. Ginouse, S. Reny

"In the mining industry time is critical as production depends on the speed of the mining cycle. During the mining process, the time required to re-open access for the next phase of an underground heading is a key point that strongly depends on the ability of the selected ground support technique to promptly ensure the safety of workers. Fiber reinforced dry-mix shotcrete has been proven to be an efficient and well adapted technique, able to produce a ground support material with the required energy absorption or flexural toughness in a single application phase. In this context, this paper demonstrates the possibility of significantly speeding up the mining process by using a new fiber reinforced dry-mix shotcrete. The new fiber reinforced dry-mix shotcrete is capable of developing flexural toughness in only 24 hours that is equivalent to what is typically achieved after 28 days using current fiber reinforced drymix shotcrete technology.INTRODUCTIONShotcrete is often used for ground support when using the drill and blast method or other tunnelling methods. But before re-opening access for the next phase of the underground heading, the applied shotcrete is required to reach a minimum compressive strength and in case of fiber reinforced shotcrete, a minimum flexural toughness (energy absorption) in order to ensure the safety of the workers going into the heading. Combined with bolts, the use of conventional fiber reinforced shotcrete becomes an interesting method for ground support as it is applied very soon after excavation and works to stabilize ground movements (Bernard E. S., 2009). In this case, the toughness development of fiber reinforced shotcrete becomes an important feature of the material when looking to speedup the mining cycle. However, early re-entry criteria in underground openings are difficult to ascertain as the load carrying capacity of fiber reinforced shotcrete is usually assessed after 7 or 28 days. For this reason, re-entry criteria varies from one mining area to another and are usually based on compressive strength requirements. For example, in northern Ontario, Canada, one of the current practices in the mining industry consists of allowing safe re-entry once fiber reinforced shotcrete has developed a compressive strength of higher than 4 MPa (Dufour, O’Donnell, & Ballou, 2003). Flexural toughness requirements on fiber reinforced shotcrete are also typically based on evaluation after 28 days."

Jan 1, 2015

By Iina Vaajamo, Jani Jansson, Lauri Pesonen

In pyrometallurgical operations, structural integrity of a high temperature furnace plays a crucial role in the overall safety, profitability and ecological footprint of the plant. Furnace integrity is related to how reliable a furnace is and it can be compromised, for example, by having poor operating and maintenance practices, an inefficient cooling system and flaws in the overall furnace design. These flaws and poor practices might lead to unexpected shutdowns, production losses, increased emissions, or worse. This paper presents the main factors to consider when engineering a furnace and developing its operating practices, while ensuring safe and reliable operations without compromising process efficiency and quality of the final products. In this respect, Outotec’s solutions for the cooling system and for automation systems like PROSCON, Process Advisor, Sentinel and our Smelting Information Management System, are also introduced.

Jan 1, 2015

By Ahmad Ghahremaninezhad, Rebecca Radzinski

Arsenic is a highly toxic compound that is naturally found in the environment and is released through the processing of sulphide minerals. Arsenate (As5+) is less toxic than arsenite (As3+) and is soluble in water but can form insoluble precipitates when metal ions are present. The arsenic removal processes used in industry assume that arsenic is in its pentavalent state. Hydrogen peroxide can be employed to oxidize arsenite; however, it is expensive. It has been shown that activated carbon can be used to catalyze the oxidation of arsenite with oxygen as the only consumed reagent at ambient conditions with an efficiency of 99% in less than 24 hours. The mechanism which oxidizes arsenite is not yet understood; however, this study shows that a strong oxidizing agent is formed in-situ. The species and amount of oxidant formed were determined via iodimetric titration and electrochemical methods. The production of oxidant was optimized by comparing the amount of oxidant formed in-situ to the relative amount of arsenite oxidized.

Jan 1, 2015

By Tom Snyder, John Brulia

PART 3 – UN Identifi cation Markings for the Highway Transportation in Commerce of Bulk Explosives, Oxidizers, and Combustible Liquids

Jan 1, 2015

By S. M. Rupprecht

"SynopsisOver the last decade in South Africa, there has been a significant increase in the number of mining operations, both open pit and underground, which use independent contractors to carry out mining activities. Often mine owners will choose the contractor option without fully understanding the consequences of undertaking this option. Traditionally, contract mining has come at a cost premium of about 15% to 20% compared to an owner mining scenario. However, due to the large number of junior mining companies entering the mining arena in South Africa contract mining rates have increased, with cost premiums as high as 50% being reported. This paper looks at the merits of owner mining versus contract mining and describes under what conditions it may be favourable to select the one option over the other. In addition, the methodology of entering into contract negotiations with the objective of establishing a fair and sustainable relationship is discussed.IntroductionOver the last decade in South Africa, there has been a significant increase in the number of mining operations, both open pit and underground, which use independent contractors to carry out mining activities. Surface mining, for example, may use contractors to conduct drilling and blasting operations or load and haul operations. Underground mining may contract out work such as shaft sinking, mining, support, construction work, cover drilling, sweeping and vampings. Common surface operations such as mineral beneficiation, waste disposal, security, and product transport may also be outsourced to contractors.Many companies have a business model that utilizes contractors for the entire mining cycle, maintaining a small head office to provide direction and control. The difficulty with this option is that often mining companies will choose the contractor option without fully understanding the implications."

Jan 1, 2015

By Q. G. Reynolds, R. T. Jones

The choice of furnace design parameters has a marked effect on the integrity of the furnace that is constructed. The design methodology for DC arc furnaces typically begins with the chemical reactions and feed materials that define the process. The specific energy requirement of the process, and the feedrates of the raw materials largely determine the power requirement for the furnace. A chosen value for the 'power intensity' sets the diameter of the furnace. Justification is provided for why this is a good choice of scale-up parameter. Equations are presented to quantify the resulting trade-off between thermal efficiency and the degree of error that can be tolerated in the balance between power and feedrate. This improved understanding should provide a better rationale for selecting an appropriate power intensity (or furnace diameter) for future furnaces.

Jan 1, 2015

By Mark McComb, Geoffrey R. Lane

"Over the years many differing approaches have been developed to clearly understand the nature, mode of occurrence, associations and deportment of both free-milling and refractory gold in a wide variety of differing geologic environments and plant products. Many approaches can be taken to characterize the ore which may occur as complex fine grained gold, ultra-fine grained gold, coarse nuggetty gold, complex Asrich refractory gold and double-refractory gold. The approach taken in assessing small drill core composites from Novo Resources Beaton Creek Paleoplacer gold project located in the Pilbara region of Australia was complicated by the nature of the ore, the small amount of sample available from current exploration work, and the gold grade and the grain size distribution. In this case the scope of the study was limited by sample availability although significant amounts of valuable information was also gained. This gold characterization study included the following elements:??Size fraction assays??Ore microscopy??Preparation of heavy mineral concentrates from sized fractions (screening) of crushed or milled head using heavy liquids and Superpan table.??Systematic scans of the heavy mineral concentrate, middling, and tailing fractions using TIMA Automated Scanning Electron Microscopy integrated with an Energy Dispersive Spectrometry to provide semi-quantitative elemental analysis of the individual grains found in the sample.The unique methodology employed to detail the gold deportment was the combination of the Tescan Integrated Mineral Analyser (TIMA) and the Oxford INCA GSR software. This technique not only allowed us to document the deportment of gold but recognize other associated minerals, which included gersdorffite, chalcopyrite, uraninite, coffinite, brannerite and several Rare Earth-bearing minerals.INTRODUCTIONGold deportment studies are commonly carried out on preliminary gold exploration projects in order to determine the various limitations, which may effect processing of the potential ore. This is often because it may be expected that there may be a refractory component to the gold, which may limit physical separation techniques and suggest more costly hydrometallurgical techniques. Often when carrying out gold deportment studies the mineralogical methods may be limited to assuming that the gold will be fine and easily found using standard techniques of optical microscopy or Scanning Electron Microscopy. This may not always be the case as various geological environments may pose their own individual problems to determining the deportment of the gold grains."

Jan 1, 2015