Search Documents

By Run-sheng xu, Hai-yang WANG, Di ZHAO, Teng-fei SONG, Jian-Liang Zhang

This paper was mainly focused on the different semi-cokes and charcoal which could be new fuels for blast furnace injection. Through the comparative study with bituminous coal and anthracite coal, the properties of semi-cokes and charcoal were presented in this research. 10 indexes of different fuels were obtained by different standard experiment, including proximate analysis, ultimate analysis, igniting point, explosivity, transportation characteristic, ash properties, grindability, calorific value, combustibility and reactivity with CO2. According to the data analysis, it provided a theoretical basis for rational utilization of various blast furnace fuels, and helped to broaden the scope of the blast furnace injection fuels. This research could contribute to energy conservation, emissions reduction, and sustainable development of iron and steel enterprises.

Jan 1, 2015

By Yuan She, Qihang Liu, Keng Wu, Hailiang Ren

By observing different coal char’s microstructures and microscopic morphologies during the coking process, the characteristics of COREX coal char’s microstructure and properties were analyzed. MCRI and MCSR were used to respectively describe the reactivity and the strength after reaction of coal char, with those of BF’s coke for reference, and then the physical meaning of MCRI and MCSR were given. MCRI and MCSR were determined by the composition of coal char. For the two kinds of COREX coal, the formula to forecast the hot performance of coal char was set up by making a multiple linear regression between the hot performance and microstructure of the coal char at 1100℃, and the predictive values of coal char’s hot performance at 600℃, 800℃ and 1000℃ coincided well with the measured values.

Jan 1, 2015

By Gaifeng Xue, Xiaohong Xu, Meng Liu, Yijie Song, Guotao Xu, Jixiong Liu

BN (Boron Nitride) based composites were prepared with hot-pressing by using h-BN as main material in ceramic preparation process. The relative density, bending strength, vickers’ hardness, thermal shock resistance, thermal expansion coefficient, thermal conductivity, phase composition and microstructure were tested and analyzed by using modern testing technology. The results indicate that the best formula is B, the relative density is 97%, the bending strength is 260 MPa, the hardness is HV5 343kg/mm2, the thermal expansion coefficient is 2.8×10-6℃-1, the thermal conductivity is 22 W/(m.K) and have no crack after thermal shock for 20 times by water cool. XRD analysis indicates that the main phase compositions are h-BN, β-Si3N4 and sialon. SEM studies show that the grains wrapped up by solid solution.

Jan 1, 2015

By Vinicius Alves Gomes, Jean Igor Margem, Thallis Cordeiro, Frederico Muylaert Margem, Roberto Faria Jr., Sergio Neves Monteiro, Marina Rangel Margem

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and neutral with respect to CO2 emission. In particular, the fiber extracted from the malva plant stem is nowadays recognized as one of the strongest lignocellulosic fibers. However, the thermal properties of the malva fibers have yet not been fully investigated. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity of a pressed malva fibers sample. The results revealed that these fibers showed a superior thermal insulation capacity.

Jan 1, 2015

By Dietmar Eifler, Marcus Klein, Hendrik Kramer

Conventional methods to characterize the fatigue behavior of metallic materials are very time and cost consuming. That is why the new short-time procedure PHYBALCHT was developed at the Institute of Materials Science and Engineering at the University of Kaiserslautern. This innovative method requires only a planar material surface to perform cyclic force-controlled hardness indentation tests. To characterize the cyclic elastic-plastic behavior of the test material the change of the force-indentation-depth-hysteresis is plotted versus the number of indentation cycles. In accordance to the plastic strain amplitude the indentation-depth width of the hysteresis loop is measured at half minimum force and is called plastic indentation-depth amplitude. Its change as a function of the number of cycles of indentation can be described by power-laws. One of these power-laws contains the hardening-exponentCHT eII, which correlates very well with the amount of cyclic hardening in conventional constant amplitude fatigue tests. To identify heat-treatment-parameters and SAE 52100 TRIP-alloys with high hardening rates as well as their damage tolerance the PHYBALCHT- and PHYBALLIT-method were used. One modified SAE 52100 TRIP-alloy was investigated in detail. The fatigue behavior and the cyclic hardening of the selected SAE 52100 TRIP-alloy was investigated and compared with conventional SAE 52100. Conventional stress-controlled fatigue tests were performed on a servo-hydraulic test system with a frequency of 5 Hz and a load ratio of R = -1. Different rates of cyclic hardening were identified. The size of the nonmetallic inclusions leading to crack initiation and the number of cycles to failure were used to evaluate differences in the damage tolerance capability.

Jan 1, 2015

By Qiang Zhong, Bin Xu, Qian Li, Yong-bin Yang, Tao Jiang, Yan Zhang

The occurrence of different ringing behaviors in oxidized pellet kiln for two kinds of coal (A and B) with similar properties, is difficult to explain based on the relationship between kiln ringing and coal properties. In this paper, the interaction of coal ash with pellet scrap powder was considered by studying the cohering behavior of powders consisting of them. The results showed that the cohering briquette strength of pellet scrap powder increased considerably when mixed with a small amount of coal ash; a maximum could be reached when the mass percent ratio of coal ash was 1.5%; the strength of powder mixed with coal B ash was always higher in same firing system. This obviously illustrated that coal B caused a more serious ringing problem. The relevant mechanism was that the stronger reactivity of coal B ash made cohering briquette have a more perfect crystallization and a more compact structure.

Jan 1, 2015

By Jinjing Dua, Jun Zhua, Kuiren Liub, Bin Wang, Xiaolei Wua

V-Ti-Fe as hydrogen storage alloy was prepared by reducing metal oxides with a metallothermic reduction method. The deoxidation process of the V-Ti-Fe alloy was performed by electro-deoxidation and vacuum induction melting method, respectively. The results showed that the content of oxygen impurity can be controlled at about 0.2wt% after electrolyzing for 240min. Both the maximum values of hydrogen absorption capacity and the effective hydrogen desorption capacity are 2.65wt% and 1.01wt%, respectively. The deoxidization effect of vacuum induction melting process is more remarkable, with Ce as the reducing agent. It is found that Ce addition is beneficial for reducing the componential segregation, promoting the hydrogen absorption activation of V-Ti-Fe alloy. When m(Ce)/m(alloy) is up to 5%, the oxygen content has been reduced to 0.05wt% and the maximum hydrogen absorption capacity and the effective hydrogen desorption capacity are up to 3.36wt% and 1.85wt%, respectively.

Jan 1, 2015

By G. Plenge, M. Brittan

"Plant design parameters for gold extraction, leach residence time and cyanide consumption are generally determined from standard bench-scale bottle roll or agitation leach tests. The application of laboratory data to process design has essentially evolved from the testing of oxide or low cyanide-consuming ores. Such scale-up factors may not be appropriate for ores that deplete cyanide and oxygen since this interferes with gold extraction kinetics. High cyanide-consuming ores also exacerbate the differences between the conditions applicable to small batch tests and large continuous operations. Testing a reactive high-sulfide South American ore deposit necessitated the re-evaluation of conventional bench-scale cyanidation procedures. Pulp density can be a major factor affecting the results for plant design purposes and should be treated as a test work variable. As with high clay-bearing ore, where pulp viscosity can hinder mass transfer, minimizing the influence of test equipment on gold extraction kinetics may require low pulp densities. This introduces interpretative complexity since cyanide consumption changes as a function of pulp density. Activated carbon also consumes cyanide, so its effect has to be accounted for in the case of carbon-in-leach (CIL) or carbon-in-pulp (CIP) plant flowsheets. Since cyanide is an expensive reagent, often a major component of plant operating costs, it is important that the scale-up of cyanide consumption from laboratory to plant be representative. The traditional method of reporting cyanide consumption in bench-scale testing is questioned since it takes credit for residual free cyanide in leach tails. The projected plant consumption may be better estimated by using the total cyanide addition in a laboratory test. We propose a test work protocol that categorizes the cyanide consumption into its components but requires more extensive testing to generate design data. The ultimate validation of scale-up factors used by project engineers requires rigorous bench-scale versus commercial plant comparative data. Such data are not readily available.IntroductionMajor factors in the design of a gold processing plant are gold recovery, leach residence time and cyanide consumption. These parameters are important determinants of project revenue and costs and, thereby, potentially of project financial viability. Estimates of the associated design criteria for a commercial plant are normally generated from laboratory cyanidation, carbon-in-leach (CIL) or carbon-in-pulp (CIP) tests using standard procedures (Angove, 2005). The key question is whether the standard laboratory test work procedures developed historically for low reagent consuming ores are appropriate for ores that are highcyanide and oxygen consumers.The present paper examines test procedural factors that can influence the test work results and, therefore, their interpretation for design scale-up purposes. The study refers in particular to a high cyanide-consuming sulfide ore. The ore was being tested to develop scoping level engineering design criteria for a proposed project in South America."

Jan 1, 2015

By L. Magne, M. Maldonado, R. Varela

Real-time optimization of flotation circuits demands for accurate and reliable measurements to support the decision making process. The collection zone gas holdup is an important variable in this context as integrates the effect of machine and chemical factors on the bubble size and velocity distributions. It has been demonstrated that gas holdup not only correlates with bubble surface area flux, which defines the particle collection rate and recovery in the collection zone, but also with water overflow, a variable which has been related to the froth zone recovery. Therefore, on-line gas holdup measurements provide a reliable alternative to judge efforts leading to the optimization of flotation cells and columns. Estimation of gas holdup in flotation from electrical conductivity measurements has been proposed and extensively used in lab and industrial installations. The approach is based on the application of Maxwell's model, which relates the concentration of a dispersed phase in a continuous medium to measurements of the conductivity of the liquid medium and of the mineral pulp with and without air bubbles included. These measurements require a conductivity cell which covers a representative volume of the flotation cell, and creates a homogeneous electric field throughout this volume that ideally is not affected by the conductivity of the medium. The development of such a cell in the limiting space and geometry of a laboratory flotation cell has been problematic, but a multi-electrode arrangement offers a promising alternative. Electrodes were installed in the flotation cell of a Denver unit; the results of preliminary testing are discussed with a focus on its performance in the measurement of two- and three-phase dispersion conductivity.

Jan 1, 2015

By R. Gray, B. Hebblewhite

Experience from Australia had identified what is referred to as nonconventional surface subsidence behavior. This occurs under irregular surface topography, resulting in valley closure, valley floor uplift or “upsidence,” and far-field horizontal movements, occurring even beyond conventional “angle of draw” limits. This paper discusses such behavior recently observed in Pennsylvania and focuses on the 2005 case of Duke Lake Dam in Ryerson Station State Park. In July 2005, there was a significant increase in water leakage through a number of growing cracks in the dam, leading to the dam being breached to avoid an uncontrolled failure. An underground longwall mine was located approximately 900 ft to the north, mining at depths of 330 to 720 ft. Investigations, including a subsequent ground movement monitoring program, found a range of evidence in the vicinity suggesting that valley closure and farfield horizontal movements may have occurred, resulting from the adjacent mining. Besides discussing the phenomenon of nonconventional subsidence behavior and the Ryerson State Park case study, this paper includes an assessment of the mining, geology and subsidence impacts and suggested ground behavioral mechanisms.

Jan 1, 2015

By K. J. Ma, L. Ma, J. Stankus

The paper’s intent is to evaluate pumpable foamed cementitious mine seal material by determining the shear strength of a generic foamed cement in the laboratory. The tests were conducted on three scales: small-size specimens, consisting of cylinders 4 in. in diameter or 3-in. prisms; double shear medium- size specimens, measuring 13 in. by 10 in.; and large-size specimens, measuring 6 ft by 4 ft by 4 ft. The small-specimen shear tests resulted in average peak and residual shear strengths of 128 psi and 56 psi, respectively. These values are fairly consistent with published shear strengths of foamed cementitious material. However, the other two types of shear tests did not achieve the shear strength of a typical pumpable foamed cementitous mine seal material. Based on the test results, the paper concluded that the structural analysis of cement foam seals should be based on their residual shear strengths, approximately 20 psi, determined from small laboratory-scale tests of the cement foam/concrete or rock interface, and not be based on their peak strengths.

Jan 1, 2015

By P. G. Dempsey, J. R. Heberger, J. P. Pollard

During a mine disaster or emergency, underground air can quickly become contaminated. In these circumstances, all underground mine workers are taught to don breathable air supply units at the first sign of an emergency. However, no contemporary oxygen consumption data is available for the purposes of designing breathing air supply equipment specifically for mine escape. Further, it would be useful to quantify the oxygen requirements of breathing air supply users for various escape scenarios. To address this need, 14 participants crawled a distance of 305 m each while their breath-by-breath oxygen consumption measurements were taken. Using these data, linear regression models were developed to determine peak and average oxygen consumption rates as well as total oxygen consumption. These models can be used by manufacturers of breathing air supply equipment to aid in the design of devices that would be capable of producing sufficient on-demand oxygen to allow miners to perform self-escape.

Jan 1, 2015

By Gregg Davidson, Lonnie Jacobs, Brett Zernich, Alan Howard, Robert Pintabona

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2014

By T Elkington, A Finch

The theory of constraints (TOC) is a business improvement method that focuses on exploiting a business’s bottleneck to deliver the highest possible profit. Early applications were mostly in the manufacturing industry; however, the theory in itself is completely generic and has now been applied widely in other industries such as services, retail, software and distribution, amongst others. The intent of the approach is attractive – it focuses on the ‘silver bullet’ rather than ‘death by a hundred projects’, and it focuses on growth rather than cost cutting. Application within the mining industry has been limited to date, although there are a few applications emerging. This paper discusses how TOC can be applied to maximise value during the project planning phase and how to maximise profits when the mine is operational. The paper uses two case studies to illustrate the approach. Case study 1 uses the approach to improve tactical mine planning, which delivers an increase in revenue of 58 per cent. The second case study is a strategic mine planning example that delivers an increase in value of 77 per cent.CITATION:Finch, A and Elkington, T, 2014. Application of the theory of constraints to strategic and tactical mine planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 129–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By P Cesare, S Munro, D Wandel, R A. Bearman

Consideration of the processing plant operational envelope is a key factor in production scheduling,and therefore mine planning, for any mining operation. In many cases hard-wired or regressionbased tonnage-grade-recovery relationships are used as mine planning constraints and as a means of valuing the system output. In extensions of this type of approach, various regressions can be used to describe throughput limits, based on a number of global metallurgical parameters.The ultimate position for the optimisation of a mine plan and production schedule is to have a full process plant model running as an integrated part of the mine planning exercise. A plant model suitable for this needs to have all the required sensitivities to input parameters such asfragmentation, grade, mineralogy, strength and hardness. The model then needs to convert these to performance measures for the plant, which include recovery, throughput, product size distributions, energy consumption, water use and operating cost.In this paper an approach is outlined that takes this view and then goes beyond it to provide a full, time-based bottleneck identifi cation and valuation tool.Using such an approach it becomes possible to run mine plans and production schedules in windows of days, weeks, months and over the life-of-mine with a time-enabled process model acting as the active constraint. In this way virtual bottlenecks can be identifi ed for various mine plans and schedules well ahead of time. The value of de-bottlenecking can be defi ned, not just at a plant scale, but in terms of the overall mining operation, and the data can be used as the basis for capital investment decisions.CITATION:Bearman, R A, Cesare, P, Munro, S and Wandel, D, 2014. Incorporation of a full process plant model as an active constraint for mine planning and production scheduling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 121–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J Whittle

This paper describes what is involved in carrying out a comprehensive optimisation of a long-term operating schedule for a mining complex. It details the data that must be assembled and discusses the different approaches to optimisation and what limitations they put on the variables and constraints that can be handled.CITATION:Whittle, J, 2014. Not for the faint-hearted, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 3–6 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By R Dimitrakopoulos, R Goodfellow

One of the primary objectives when optimising a mining complex is to maximise its value for the primary stakeholders. In order to achieve this objective, it is necessary to holistically optimise all aspects of the mining complex, including decisions of when to extract materials from the available sources, how to blend or stockpile these materials and how to best use the available processing streams to satisfy customer demand. Existing methods for global, or holistic, optimisation ignore the compounded effects that risk has on the performance of a mining complex. Over the past decade, several stochastic optimisation approaches have been proposed to integrate various forms of uncertainty into the open pit mine design and production scheduling. These methods, however, are limited in their ability to simultaneously optimise the production schedules for the portfolio of mines, material destination policies, the use of the available processing streams and the various products that are produced at each location of the mining complex.This paper aims to discuss a new method for the global optimisation of open pit mining complexes with geological uncertainty. The proposed generalised methodology is capable of modelling and holistically optimising mining complexes, including aspects related to production scheduling, blending, stockpiling and non-linear interactions that often occur in practice, but are over-simplified in existing models. Two case studies are discussed to highlight the need for these complex, stochastic optimisers. First, a case study for a nickel laterite blending operation highlights the need to integrate geological uncertainty into the optimisation in order to ensure product quality constraints are respected. Second, a case study for a copper-gold mining complex highlights the added value when simultaneously optimising the production schedule and the stockpiling and treatment of extracted materials.CITATION:Goodfellow, R and Dimitrakopoulos, R, 2014. Stochastic optimisation of mineral value chains – developments and applications for the global optimisation of mining complexes with uncertainty, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 13–22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By H M. Parker, G Verly, T Postolski

Assessing the uncertainty and risk in mineral resource estimation is required for best practice and is implied by the public reporting codes in the categorisation of mineral resources and reserves. One industry best practice is quantifying the risk on future production for a given period, which can be done using two geostatistical approaches: conditional simulation and drill hole spacing studies based on estimation variances. Conditional simulation can provide a more complete and flexible answer to the problem, but it takes a fair amount of time to complete. Drill hole spacing studies are simpler, faster and can provide reasonable assessments of mineral resource uncertainty.This paper is a presentation of the principles, theory and practice of drill hole spacing studies. Various types of risk assessment are considered. Difficulties encountered in practice are discussed, and solutions are proposed. The important parameters impacting the results are reviewed. Examples of results and sensitivities are shown.CITATION:Verly, G, Postolski, T and Parker, H M, 2014. Assessing uncertainty with drill hole spacing studies – applications to mineral resources, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 109–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J Balzary, A Mohais

Dynamic market and operating conditions, coupled with an environment in which multiple objectives and trade-offs are common, pose major challenges for planners and schedulers working in any mining entity. Many mining companies recognise the need to shift from a siloed mining-focused push model to an integrated value chain, demand-driven approach, but there are still fundamental barriers in business process and the supporting technology preventing a consideration of end-to-end optimality.This paper presents some elements of experiences working with companies to adopt such advanced approaches. In addition to algorithmic elements, an approach to phased and gradual deployment of progressively more sophisticated optimisation models is described. From a practical software adoption perspective, it is believed that this last concern is also of primary importance. Next generation approaches to the optimisation of complex bulk commodity demand chains, namely iron ore and coal are presented, with case studies in the world’s largest integrated operations in Western Australia and Queensland from the raw material mined through to market. Utilising accurate simulation models supported by metaheuristic optimisation techniques, a range of ways to engineer a dynamic decision support framework that can adapt and change with the inevitable changes in commodity markets is explored. Objectives such as total revenue, margin, cost, NPV, throughput, asset utilisation, contractual penalties and bonuses, and energy consumption can be managed simultaneously across the mine, plant, logistics network, port operation, shipping and sales domains.CITATION:Balzary, J and Mohais, A, 2014. Consideration for multiobjective metaheuristic optimisation of large iron ore and coal supply chains, from resource to market, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 213–222 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By S Q. Liu, E Kozan

This paper proposes a new multiresource multistage scheduling problem for optimising the open pit drilling, blasting and excavating operations under equipment capacity constraints. The flow process is analysed based on the real-life data from an Australian iron ore mine site. The objective of the model is to maximise the throughput and minimise the total idle times of equipment at each stage. The following comprehensive mining attributes and constraints have been considered: types of equipment; operating capacities of equipment; ready times of equipment; speeds of equipment; block-sequence-dependent movement times of equipment; equipment-assignment-dependent operation times of blocks; distances between each pair of blocks; due windows of blocks; material properties of blocks; swell factors of blocks; and slope requirements of blocks. It is formulated by mixed integer programming and solved by ILOG-CPLEX optimiser. The proposed model is validated with extensive computational experiments to improve mine production efficiency at the operational level. The model also provides an intelligent decision support tool to account for the availability and usage of equipment units for drilling, blasting and excavating stages.CITATION:Kozan, E and Liu, S Q, 2014. An Open pit multistage mine production scheduling model for drilling, blasting and excavating operations, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 329–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014