Search Documents

By Robert E. McIvor

"“Classification System Efficiency (CSE)” is a powerful, emerging tool that can be used to increase grinding circuit efficiency. It is defined as the percentage of the ball mill energy being used to grind target, oversize particles. The discovery, validation and current use of CSE, including how it was manipulated, are described through seven plant case studies. These resulted in efficiency improvements ranging from 3 to 30 percent, along with major reductions in over-grinding. The achievable CSE for any given circuit is described. This paper demonstrates both how, and how much, every plant can benefit from increasing grinding circuit CSE.DEFINITIONS: BALL MILL CIRCUIT “CLASSIFICATION SYSTEM EFFICIENCY (CSE)”, “EFFECTIVE MILL GRINDING POWER”: “WASTED/OVER-GRINDING MILL POWER”The closed ball mill circuit is shown in Figure 1. The extreme importance of the circulating load ratio in determining circuit productivity was demonstrated by Davis (1925) and re-published by Guadin (1939), as shown in Figure 2. The circuit production rate increases with increased circulating load ratio, rapidly so at first and continuing to increase more gradually with higher and higher values of circulating load ratio.The underlying cause of this relationship was seen when comparing the ball mill feed and product size distributions from two different ball mill circuits, one with a low circulating load ratio, and one with a high circulating load ratio (Figure 3). While the F80’s and P80’s of these two circuits were close to the same, the mill feed and discharge size distributions were quite different. The ball mill in the circuit with the higher circulating load ratio contained a substantially greater fraction of material coarser than the target P80, as indicated by the respective mill feed and discharge size distributions. This fraction represents the fraction of the mill power being expended on “coarse” (in this case, plus P80 size) material, or the circuit “classification system efficiency.” The “effective mill grinding power” is the total mill power multiplied by the CSE. The compliment of CSE, the remaining fraction of “fines” in the mill, is the fraction of the mill power being wasted, and spent on over-grinding of material already finer than the circuit target product size. This is the “wasted/over-grinding mill power”"

Jan 1, 2013

By J. Paraszczak

ABSTRACT Diesel-powered loaders are a pillar of modern underground metal mining. As these mines are getting deeper and hotter and the emission regulations stricter, ventilation costs are soaring, affecting production cost. Also, the cost of diesel fuel is expected to rise. These may make the use of diesel engines more problematic. Electric load-haul-dump machines (LHDs) are an interesting alternative. This paper compares features and performance of diesel and electric, cable-powered LHDs. It overviews equipment offerings, and compares, analyzes and discusses technical parameters, operational problems and cost issues. The paper gives some conclusions about electric LHD applicability and performance, indicates possible applications, and suggests further research work.

Jan 1, 2013

By S. Yalcin, S. Chang, M. Oliazadeh

"Present day ferrochrome demand is on the rise, as more steel products require this material as an alloying element. It is projected that the stainless steel demands will grow by about 6% per year to 2020; as such, the supply and demand for ferrochrome appears promising. Chromite is the only economical source of chromium, which is commonly upgraded by gravity techniques and used to produce ferrochrome. The gravity separation methods are not able to treat particles finer than 0.1 mm efficiently. Therefore, in processing chromite ore, a large quantity of fine tailings; some 25% of the mineral values have been reported as lost in slimes during processing. The chromite content of these tailings is typically 10-20% Cr2O3 and accumulates into a large stockpile/pond. A chromite concentrator project in Canada, considers a cut-off grade of 20% Cr2O3. This indicates further processing might be required to recover chromite from low-grade stockpile when the high-grade deposits are depleted. Low-grade ores normally indicates disseminated chromite ores with low liberation and consequently fine comminution. This paper reviews the techniques for treating chromite from fine material and provides some examples of successful operations in fine chromite recovery. Beneficiation techniques for fine particles include gravity separation, magnetic separation, and flotation. Several case studies are presented here that used one of the aforementioned methods or a combination of them.INTRODUCTIONChromium is one of the essential element and important material for production of ferrochrome alloys and special steel. Chromium occurs as chromium spinel, a complex mineral with chemical composition of (Fe, Mg) O (Cr, Al, Fe)2 . Chromite ore is exclusively found in ultramafic igneous rocks. Major associated gangue minerals are talc, quartz, serpentine and iron oxides.Chromite is a heavy mineral, with a specific gravity in the range of 4-5, relative to associated gangue minerals in a chromite ore, which makes gravity concentration a suitable process. This is generally true for coarse particles, ranging from 1 mm to 100 mm. Typically, the ore is prepared by crushing (and grinding if necessary) to a suitable size and the material is sized for the appropriate beneficiation techniques. It is common to use heavy medium separation (e.g. dense media drums, dense media cyclones, or Dyna Whirlpool) to treat coarse size and intermediate size particles (1 – 100 mm). Intermediate and fine particles (20 – 0.1 mm) could be treated by jigs. Spirals, shaking table, sluices, and Reichert cones can upgrade fine particles. Figure 1 shows a typical chromite beneficiation process flowsheet. As can be seen, it consists of three major sections: feed preparation (crushing, screening), de-sliming, and concentration. Beneficiation recoveries range from 80 to 85%, although the ratio of upgrading is only 2 to 3."

Jan 1, 2013

By A. Kapito

The formation of bainite in steel is dependent on the size of the casting, the heat treatment, and the alloying elements. It is difficult to obtain a fully bainitic microstructure in steels during heat treatment because of its close proximity to the martensite (a?) reaction. The ferrite (a) and pearlite reactions in steels are also rapid and shield the bainite reaction. Alloying elements therefore need to be added to separate the bainite reaction. Boron (B) and molybdenum (Mo) are key elements added to bainitic steels because of their ability to retard the a reaction. Other elements used in the production of bainitic steels are silicon (Si), chromium (Cr), manganese (Mn), and titanium (Ti). In this paper we investigate the effect of alloying elements on the bainite reaction through the use of dilatometry. Dilatometry is a technique that determines phase transformations in the steel and through which continuous cooling transformation (CCT) curves can then be developed. Some initial results are presented of an ongoing study on the development of bainitic steels for railway wheel applications.

Jan 1, 2013

Improvements in cost efficiency, noise control, environmental design and ergonomics ? the mining and construction industries are facing demands on many fronts. The international manufacturers of construction machinery are responding to these challenges, and they will be presenting their innovations in all these fields at bauma 2013. bauma, the international trade fair for mining and construction machinery, mining vehicles, and building material machines, takes place from April 15 to 21, 2013 at the Messe Munchen exhibition center in Munich, Germany. The last bauma, in 2010, attracted 3,256 exhibitors from 53 countries, and more than 420,000 visitors from more than 200 nations. Covering a total of 555,000 m2 (5.97 million sq ft) of exhibition space, bauma is one of the largest trade shows in the world. This year?s fair is expected to surpass the 2010 figures. Here are some examples of the new developments visitors can expect to see at the show.

Jan 1, 2013

Smart defense: that?s what the industry needs to play for the next four years, according to panelists at the 118th Annual Meeting of the Northwest Mining Association (NWMA), which met December 2-7 in Spokane, WA. The conference was well attended, with approximately 2,200 attendees, 244 booths in the two packed exhibition halls, and a rich offering of short courses, field trips, social events and technical sessions. Speakers at the packed legislative session articulated many of the frustrations felt by members of the mining community after the U.S. elections in November, and offered words of advice. Matthew Ellsworth, the new Government Affairs hire at NWMA, stated it best: ?Elections are like Christmas: you find out who?s naughty and nice ? and it?s always going to come again.?

Jan 1, 2013

By Vicki Tschirhart, Bill Morris, McMaster University

A new method for mapping faults within basement rocks underlying the Thelon Formation and glacial overburden was developed and tested in the Aberdeen Sub-basin. This method utilizes newly acquired aeromagnetic data, the Blakely algorithm for defining magnetic source edges, a calculated dip-direction map, a digital elevation model (DEM) derived from the Canadian Digital Elevation Database, and the positions of identified, inferred and newly mapped faults that are within and adjacent to this sub-basin. Combining these data revealed three age groups of faults. One group is seen only on the DEM; these faults are young brittle structures that have no effect on the sub-Thelon basement unconformity, and are not visible on the dip direction map. A second group is evident on the dip direction map but not the DEM; these faults are old basement structures that did not propagate upward through the Thelon Formation. The third group is expressed on both the DEM and dip direction map; these faults are also old structures that propagated upward during and/or after deposition of the Thelon Formation. The latter group of faults may be of greatest interest for uranium exploration, with reactivation increasing their potential to serve as conduits to transport uranium-rich fluids and focus deposition at or near the unconformity surface. This methodology has promise for comprehensive mapping of basin faults and tracking the tectonic development of the whole Thelon Basin through time.

Jan 1, 2013

By Todd Burchett

Mining engineers spend countless hours and resources when designing a new underground coal mine. Their primary objective is to design the safest and most efficient operating mine with regards to coal production. A key variable often overlooked in this design stage is the slope conveyor. Typically, a slope conveyor is expected to operate with a 98-percent or higher availability. However, too often little effort is put forth by the mining engineer to optimize its design. Coal companies will rely on engineering, procurement, construction and management (EPCM) companies for the preliminary design, because the slope conveyor will be considered part of the surface material handling processes. This preliminary design will be used when soliciting quotations for the slope conveyor. Unfortunately, EPCMs may not have enough expertise with conveyors to optimize the design. This expertise is available with an original equipment manufacture (OEM) of conveyors, which ultimately may be responsible for supplying the slope conveyor. Each OEM will provide a bid package that represents what it considers to be the optimal design.

Jan 1, 2013

ABSTRACT It is critical that historical processes and concomitant exposures to specific nickel substances be understood because some diseases linked to inhalation of certain nickel-containing substances have a long latency between first exposure and disease onset, and because nickel substances vary significantly in their toxicological properties. A discussion of the smelting history and related processes at Vale Canada’s (Inco’s) Copper Cliff, Ontario, smelter is integral to the understanding of these processes. The post-1950 processing history, equipment, propensity for aerosol formation, operational procedures, and ventilation controls used by Vale Canada in roasting, smelting, converting, and copper-nickel separation is discussed.

Jan 1, 2013

By Heather E. Lawson

Recent field data providing measured pillar loading from a deep western mine revealed that an increased load transfer distance existed compared to expected values (Larson et al., 2012). Additionally, recent work by Tulu and Heasley (2012) has shown that the abutment angle in deep longwall mines can be significantly reduced as the depth of mining increases. The load transfer distance and abutment angle are both used as parameters to estimate pillar loading in longwall design. To investigate the potential implications of these observations on pillar loading in deep longwall mines, a parametric study using ALPS loading estimation procedures was performed. A supplemental study was conducted using LaModel to further investigate pillar loading at the tailgate. The study found that the abutment angle is particularly important for panels with supercritical geometries. As panels reach a subcritical geometry with increasing depth, the primary influence of the abutment angle is reduced and matched by other factors, including load transfer distance for tailgate loading. An extended load transfer distance was shown to potentially reduce loading on pillars adjacent to the longwall as the loading is spread over a larger area. The results of these studies indicate a need for further field verification and research toward regional geologic influences on pillar loading and how these may impact ground stability.

Jan 1, 2013

By G. Couture, J. -F. Dubé, F. Letarte-Lavoie

"The Xstrata Nickel Raglan concentrator, located in Quebec’s Nunavik region, has been in operation since 1997. Originally designed to process 800,000 tonnes per year of high-grade nickel ore, the plant’s current capacity is 1.3 million tonnes per year due to various optimization projects. In 2011 and 2012, the Metallurgical group, with assistance from BBA, updated and optimized the variables affecting SAG throughput in order to optimize process stability while maintaining maximum plant throughput. This project consisted of reviewing the control strategy and completely updating the pre-existing Fuzzy Logic controller. This paper describes the successful update of the controller including a complete revision of control rules, a new process control strategy and the integration of new process variables, most notably mill rotational speed. It will also show how this new approach has provided a simple and robust way of delivering both an increase in throughput while reducing process variability.INTRODUCTIONThe Xstrata Nickel Raglan Mine concentrator is located in Northern Quebec along the 62th parallel. It has been in operation since 1997 and was originally designed to treat 800,000 tonnes of ore annually. The Raglan Agreement held with the Makivik Corporation and the Inuit communities limits the annual tonnage of ore that can be processed at 1.32 million tonnes.The ore is processed in a 24 foot variable speed, semi-autogenous grinding mill (SAG). The conversion from Autogenous Grinding (AG) to SAG was completed in 2006. Before the ore is processed by the SAG, its size is analyzed by a Wipfrag camera that provides a granulometry estimate. A cone crusher reduces the SAG’s discharge screen’s oversize material. A 14 foot diameter ball mill ensures final grinding before the flotation stage.Many control strategies were used at the SAG over the past few years. Fuzzy Logic was first used in 2007 in order to control tonnage feed to the SAG. This first version only measured the value of the variables without taking into account their rate of change. Revisions were made over the course of the last few years to improve controller performance. Other variables were added such as slurry density and crusher Closed Side Setting (CSS). The previous revision of the Fuzzy Logic was done in 2009 with a review of the rules only."

Jan 1, 2013

By Dan Wang, Qian Li, Yong-bin Yang, Tao Jiang

"Thiosulfate is one of the most promising non-cyanide lixiviants for gold leaching. However, the undesirable reaction between thiosulfate and copper (II) gives rise to increased reagent consumption, which results in high cost and huge limit to its development. This paper presents study on the effect of ammonia, copper (II) and Cu(NH3)l+ ions on the oxidative decomposition of thioulfate. It shows that the presence of copper (II) and Cu(NH3)l+ can significantly increase the thiosulfate oxidation, while ammonia is relatively unaffected. The oxidation of thiosulfate by copper(II) in the absence of ammonia is fast at first and then decreases as time increased within a certain time, which can postulate that an intermediate product is responsible for the decreased consumption. The effect of ammonia is depended on the interaction with copper (II), which was found to significantly affect the consumption of thiosulfate.IntroductionFor over one century cyanidation is widely used in industrial production of gold, due to its simplity of process and low cost of production. However, cyanide is a highly toxic chemical reagent used dangerously and brings serious environmental pollution. What's more, cyanidation has slow speed of leaching gold and poorly leaching effective for refractory ores. With the exhausting of free-milling gold ores and promoted environmental protection requests, the disadvantage of cyanidation becomes a growing problem. In recent years, more and more research activities have been focused on alternative processes using non-cyanide lixiviants. Among the non-cyanide lixiviants, thiosulfate is considered as the most promising one[l-5].Compared to cyanide, thiosulfate is an inexpensive, nontoxic and less-pollution reagent, which can form complexes with many metal ions. Thiosulfate leaching of gold has an acceptable leaching rate and is insensitivity to impurities. Moreover it presents advantage on the treatment of refractory gold ores such as carbonaceous gold ores, copper gold ores, complex arsenic and sulfur gold ores, and so on[6]."

Jan 1, 2013

By Ulrich Leiste, David M. Fox

This paper presents the results from small scale testing aimed at measuring the loads on a rigid target due to the detonation of a buried mine. The aim of this research is to find how the impulse delivered to the target varies as the air filled void volume fraction within the soil changes.

Jan 1, 2013

By Norman Paley, Finn Ouchterlony

Detailed fragmentation data for different blast delay timing tests at the Red Dog mine in Alaska are analyzed. This work is a continuation of previous work in which the crusher output was found to be better described by the three-parameter Swebrec function than by the Rosin-Rammler function. For a crusher model, the x50 variable sufficed to describe changing crusher input while b and xmax could be considered fixed. For the crusher output from aggregated stockpile rock, as measured by digital image analysis using Split-Online, the constancy of b was not as apparent. In this paper detailed stockpile data, single Split data series, and sieved belt cuts of crusher product are analyzed using the Swebrec and truncated Rosin-Rammler functions. The variability of b is confirmed. By using specific fraction passing sizes a shortcut is presented that removes the need to do curve fitting to determine the three Swebrec function parameters.

Jan 1, 2013

"The characterisation of resources and description of variability across different ore domains is key to accurate prediction of probable metallurgical performance. Such characterisation testwork often has limited drill-core from which to work and this immediately confines the characterisation method to smallscale. For flotation feeds, the JKMSI (Mineral Separability Indicator) is being developed as a potential characterisation tool, building on earlier work by Chudacek, (1990), which used shaken test tubes, and was called the EMDEE device. In addition, the consistency of flotation recovery for specified size fractions has shown to be preserved, irrespective of the amount of material in that size fraction obtained by different milling conditions, so that the overall recovery can be estimated from knowing the particle size distribution (McIvor and Finch, 1991; Bazin et al, 1994, Runge, 2007 and Wightman et al, 2010) The JKMSI unit uses less than 10 g of material per test in narrowly sized classes and results to date have demonstrated the value of the test. This paper discusses the potential of the test by demonstrating the link between JKMSI performance and mineralogy of five different ores from Laguna Seca, Escondida Minera Limitada as well as the correlation to plant scale performance obtained in an earlier survey (Coleman et al, 2006). Further work to tie down the proof of representatively of the small sample has been identified and is discussed and included in the paper. INTRODUCTIONSince the uptake of the flotation process at the turn of the twentieth century, small scale, laboratory methods have been sought to characterise flotation response. Although laboratory batch flotation tests are the most widely used method to evaluate reagents, characterise ore variability and obtain suitable model parameters using various scale up factors Runge (2101) other methods using less ore would be useful where ore samples were limited.A method using test tubes for testing ores’s flotation response to reagents was first developed by Ian Walk (Wark & Wark, 1935; Wark; 1938; Sutherland and Wark 1955). In these tests a 50 cc stoppered measuring cylinder served as a means for a qualitative experiment, the aeration being effected through violent shaking by hand. In these experiments about 10 g of mineral was ground by pestle and mortar under water after which the ground material was deslimed and adequately conditioned with the appropriate reagents."

Jan 1, 2013

By Hadi Fanisalek

"Most industries attempted to conduct their energy consumptions in an optimized way for a few decades. This is because policymakers and top managements in industries have felt the critical situation of a possible energy shortage that could happen for them in the near future, even in countries with significant fossil fuel resources. Decisions related to energy consumption in any industry will have a long-term effect on different parts of the industry structure. In this way, energy decisions should be categorized as part of any industry's main strategic and long-term decisions, which should be made by top strategists. On the other hand, strategic management has many powerful tools to help the policymakers in industries to establish a long-term strategy for energy consumption and reducing or preferably eliminating the energy loss. This will be more important for industries in the Middle East, where they have just started to make an applicable strategy for their energy consumption and to design a long-term procedure for their energy management. Based on strategic management and by comparison we designed and offered a new model for establishing the main structure of energy management strategy in primary aluminum industry, which is a high consuming energy industry. This strategy, which we will call ESM (Energy Strategic Model) and has been applied for a typical primary aluminum industry in this paper, is similar to the practical models in the field of strategic management, which were developed for designing the overall company strategy.IntroductionThe elementary goal for introducing strategic management in any organization was to establish a successful plan helping the company to survive and to gain competitive advantage over its competitors in a rough business environment. Strategic management is an ongoing process that evaluates and controls the business and industries in which the company is involved; assesses its competitors and sets goals and strategies to meet all existing and potential competitors; and then reassesses each strategy annually to determine how it has been implemented and whether it has succeeded or needs replacement by a new strategy to meet changed circumstances, new technology, new competitors, and a new economic environment[!]."

Jan 1, 2013

By L. Flett, S. Woods, C. Deredin

"Following a significant reduction in world Imperial Smelting Furnace (ISF) capacity from 2003 to 2008, a major optimization initiative was successfully carried out on the lead upgrading and bulk (zinclead) flotation circuits in the Brunswick Concentrator.This paper describes the process improvements that have taken place in order to reduce the quantity of bulk concentrate:•,Increase in lead upgrading rougher flotation circuit capacity•,Installation of a closed-circuit bulk regrind utilizing MillPebs and 150 mm Cavex hydrocyclones•,Installation of two additional cleaner flotation stages on the bulk circuit•,Optimization of the manipulated variables in the lead upgrading and bulk circuitsINTRODUCTIONThe Brunswick Mine (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The planned closure of the mine will take place at the end of the first quarter in 2013. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.A simplified flowsheet for the concentrator is given in Figure 1. The overall flowsheet involves SAG milling, secondary ball milling, selective flotation, and dewatering by thickening, filtering and drying. The complexity of the flowsheet evolves from the requirements for fine grinding and the production of four concentrates: zinc (sphalerite), lead (galena), copper (chalcopyrite) and bulk (sphalerite plus galena).Primary hydrocyclone overflow feeds the copper-lead aerator-roughers for flotation at pH 9.0 with soda ash. Plant xanthate (80-20 sodium isopropyl and potassium amyl) and AP407 are used as collectors in the copper-lead circuit. The rougher concentrate is directed to the copper-lead regrind circuit and the tailings are fed to the secondary grinding circuit. The secondary hydrocyclone overflow from the secondary grinding circuit feeds the copper-lead rougher-scavenger banks. Rougher concentrates are reground to a P80 of 28 µm prior to three stages of copper-lead cleaning. The first stage of cleaning is done in an open circuit with the tail reporting to the cleaner scavenger. The cleaner scavenger concentrate reports to the regrind circuit and the cleaner scavenger tail combines with the rougher/scavenger tail to feed the zinc circuit. The second and third stages of cleaning are performed in closed circuit with the cleaner tail being recycled to the copper-lead regrind circuit. The average final concentrate grades 23% Pb, 3% Cu and 704 g/t Ag, and is fed to the copper separation circuit."

Jan 1, 2013

When it comes to safety in the mining and extractive industries, success is literally a matter of life and death. Anything short of perfection is not acceptable. In recent years, the mining industry in the United States has made tremendous strides in terms of health and safety for its workers. Part of that success has come with an increased focus on the issues of safety, an intense examination of procedures, liberal sharing of best practices and a focus on the synergy between safety, reliability and environment. During his closing keynote address of the Safety Management & System Reliability Conference in Minneapolis, MN on Nov. 15, Joe Driscoll, vice president of Great Basin Gold, showed a calendar from the coal fields in Pennsylvania from the early 1900s. The calendar marked the number of mine-related deaths each month. Some months, the number was as high as 50. It was an illustration of how far things have come, but there is still much more work to be done.

Jan 1, 2013

Miners really are an optimistic bunch. Even with the dark clouds hanging over the global industry, mining professionals still turn out in droves at industry conferences. In February, more than 7,200 professionals attended SME?s Annual Meeting in Denver, CO, a record. And the following week, more than 30,000 people converged on Toronto, ON, Canada for the Prospectors and Developers Association of Canada (PDAC) meeting. For many small and junior mining and exploration companies the PDAC conference is a place to find potential investors in their projects. The Investors Exchange attracts several hundred companies, each showing off their properties to the many money types who wander the hall during the four-day conference.

Jan 1, 2013

By R. H. Batey

"The process control and cost of monitoring mining slurries is normally accomplished using a continuous mass flow system, conventionally embodying a volumetric magnetic flow meter and nuclear density meter. DuPont’s Maxville Mine at Starke, Florida, USA was chosen to examine costs associated with performance of a nuclear density meter. Since it is typical of many mid-sized establishments and has a long history in their use. The published accuracy under ideal conditions of a nuclear density meter is ± 1.0%, but in practice considerable ambiguity of cost in annual production implies ± 2% at best. Using such accuracy in a 400mm (16”) pipe carrying zircon slurry at 75,000 tons/day, the cost of ambiguity, together with initial and running costs, amount to nominally $962,000 per year.Such cost leaves much to be desired. This paper describes an unique continuous, direct mass per unit volume Density Meter used for mining slurries in pipe sizes up to 1000mm (40”), which significantly reduces the cost of ambiguity of measurement and running costs. At the same time the disadvantages of nuclear devices are obviated.In an effort to reduce costs, a 400mm non-nuclear Density Meter was installed at the DuPont Maxville mine. A typical on-site accuracy can be shown to be ± 0.285%, whereby the cost of ambiguity, initial and running costs in the example above shows an annual improvement of $78,660, a reduction of over $880,000 per year.Even higher cost savings may be demonstrated with mass flow systems having gas entrainment compensation. Unlike nuclear and other inferential density meters, the signal quality of this non-nuclear Density Meter is totally unaffected by entrained gas found in mining slurries. This non-nuclear density meter is then ideally used with a vortex velocity domain sonic flow meter, and provides for the first time compensation in wet density or dry % solids, as well as wet or dry mass flow of mining slurries with entrained gas, resulting in enormous reductions in cost ambiguity."

Jan 1, 2013