Search Documents

By Maral Papazian Bedian

"Case 2. 100th Street Bus Depot: Elimination of Deep Caissons in Favor of Spread FootingsThe PROJECTThe 100th Street Bus Depot is a new five-story bus terminal for the New York City Metropolitan Transit Authority occupying one city block in Manhattan between 99th and 100th Streets, and between Lexington and Park Avenues. It replaces a former two-story garage, built in the 1890’s and initially used as a trolley-car barn. The new structure is a steelframed building with concrete floors and includes a partial basement near its middle. The easternmost column line with design loads of 10 MN (1,125 tons) is within 1.5 m of the underlying multi-tube Lexington Avenue subway system. To support the new columns along the subway line, the project bid plans had called for 1 m diameter and 17 m deep drilled shafts. The upper 14 m of each unit would have required 50 mm separation from the surrounding rock to prevent stress from being imposed on the roof and walls of the adjacent tunnel. The column loads were thus transferred to below the base of the tunnel and supported by 3 m long sockets in bedrock. The bid documents contained extensive test boring information, which revealed that the project site was underlain by massive Manhattan Mica Schist bedrock within just 3 m below street level. In fact, the Lexington Avenue two-level and multi-tube subway had been tunneled through this rock circa 1910, leaving an about 6 m thick solid roof over the upper-level subway. The NX rock core recovery values were near 100 %, with average RQD of 75 %.The CHANGEThe Bus Depot project was let as a design/build contract with a very aggressive fast-track schedule. Both the pre-bid preliminary design and the subsequent final design by the Contractor’s own hired design engineers relied heavily on very restrictive codes, including unnecessarily conservative approaches to seismic design. Any suggestion for value engineering change was undesirable and was strongly resisted. Yet, objecting against the blind reliance on codes in foundation design, the author questioned the real need for the deep drilled shafts to support the columns along the subway. The unsupported statement that no stresses from the new structure can be imposed on the roof and walls of the adjacent tunnel was not sufficient reason for the drilled-shaft design. Unconvinced that deep shafts were necessary, the author rushed to MTA’s warehouse where many rows of rock core boxes were neatly stacked. Careful inspection and some simple testing of the rock cores with the blows of a geologic hammer gave support to the reservations about the design. Later, as expected, the schist bedrock at this site was found to be hard to very hard with unconfined compressive strength values estimated to range from at least 70 MPa to over 100 MPa (10,000 psi to 15,000 psi). The tensile strength of the rock was assessed to be minimum 5 MPa (750 psi)."

Jan 1, 2003

By J. Postle, Deborah McCombe

"This is the third in a series of articles about the Committee for Mineral Reserves International Reporting Standards (CRIRSCO). The first article was an interview with Niall Weatherstone, Chairman of CRIRSCO (CIM Magazine, February 2008) the second described the background and goals of CRIRSCO (CIM Magazine, March/April 2008). In 2007, CRIRSCO was adopted as the Reserves and Resources Task Force of the International Council on Mining and Metals. This decision by ICMM has resulted in an increased level of funding for CRIRSCO and the ability to advance its objectives. In mid-October 2007, CRIRSCO members met in London England to discuss the status of each of the member countries’ reporting codes and the progress of various CRIRSCO projects. Update on national reporting codes Australia: The last update of the Australian JORC Code was in 2004. While there are ongoing discussions about issues that arise from the application of the latest version of the Code, there are no plans to update JORC in the near future. Canada: The Canadian Securities Administrators revised National Instrument 43-101 in December 2005. At the same time, the Canadian Institute of Mining, Metallurgy and Petroleum published updated Resource and Reserve Definitions that are incorporated by reference in NI 43-101. CIM is continuing work on developing Best Practice Guidelines to assist practitioners in the estimation of Mineral Resources and Reserves. South Africa: The South African Mineral Reserve Committee is currently awaiting an update of the Johannesburg Stock Exchange Limited Listing Rules, which will incorporate both SAMREC and SAMVAL (South African valuation guidelines). The official launch of both codes is expected in 2008. Europe: The Pan-European Reserves Reporting Committee expects to release a consultation draft in 2008. Emphasis is being placed on industrial minerals and aggregates, which constitute a very large industry in Europe. Chile: The Chilean Certification Code was approved in early 2008. As part of the Code, a National Commission is being established to screen and review reports on a random or specific basis. United States: The Society of Mining Engineers updated the SME Reporting Guidelines in 2007. The Securities and Exchange Commission has not accepted these more up-to-date definitions and guidelines. The SME committee will continue to discuss the incorporation of these Reporting Guidelines with SEC. SME has also established a class of membership, a Registered Member, which includes disciplinary measures for non-compliance with the SME guidelines."

Jan 1, 2003

By Guojun Qi

This work relates to wafer bumping technologies for flip chip packaging applications in the electronics industry. Nickel and its alloys are alternative under bump metallization (UBM) materials because of their slower reaction rates with Sn-based solder as compared to Cu-based UBMs. In this study, we compared the morphologies of the intermetallic compounds (IMC) formed between Sn-bearing solders (Sn3.5Ag and eutectic Sn-Pb) and two types of nickel- based UBMs, electroless Ni-P (EN) and sputtered nickel. Both chunky-type and needle-type of intermetallics were observed between the EN UBM and the solders. In the case of sputtered Ni UBM, there is only a layer of scallop-type intermetallics formed. The morphology change and growth kinetics of the IMC in thermal aging process were analysed. Kirkendall voids were noticed from samples of Sn3.5Ag solder vs Ni-P UBM that have undergone prolonged thermal aging at high temperature.

Jan 1, 2003

I would like to build on the keynote address given by Peter Stoker to the Fourth International Mining Geology Conference (2000) entitled æThe Role of the Mine GeologistÆ. He concluded that à the important aspects of the professional contribution of a mine geoscientist to a mine operation include: The geoscientists prime task is to maximise the profitable extraction of the ore deposit on which they are working û that is to add value. They must maintain and develop their own expertise. By ensuring a truly professional approach to all they do, they will provide the best service to the community, to their company or client, their shareholders and their family or close associates. In that process they will also assist in protecting themselves in this increasing litigious world. I intend to build on these points and, in particular to expand on what it really means to take a truly professional approach to mine geology. Mine geology is different from other forms of geological practice. As a mine geologist you are the advocate for the orebody. After all the orebody is the one thing that is unchangeable.

Jan 1, 2003

By J. W. Davis

In the last few years major industrial companies have begun to realize the importance of Reliability as an enterprise strategy that, properly implemented, will improve financial performance. Typical results of an effective Enterprise Reliability Strategy include a 20% -50% reduction in maintenance cost accompanied by a 5% - 10%increase in real production capacity, with no capital investment in production equipment. One factor fueling the race to acquire and implement enterprise reliability is the pressure for companies to be increasingly cost-effective and competitive in global markets. In a recent study, Asset Productivity: The Next Wave, the Boston Consulting Group (BCG)stated that, “In order to compete for funds, companies must offer investor returns that are competitive with other opportunities. Alternative investments such as dot-com and others with non-traditional business models have raised the bar.” (APDF version of the study can be downloaded at www.bcg.com). BCG views asset productivity as the most powerful mechanism for increasing shareholder return. The author believes that the most effective way to increase Fixed Asset Productivity is to maximize asset utilization by increasing the Reliability of the Assets and the associated processes. Developing and implementing an ERS requires significant effort and knowledge. Most companies have difficulty finding a sufficient supply of these valuable commodities to implement an ERS Program internally. Many companies also struggle with figuring out how to get started and what direction to proceed.

Jan 1, 2003

By Steve Kral

Mining is a risky business. The cost of exploring for new mineral deposits is high and the success rate of finding one worthy of development is relatively low. And once a deposit is identified, there is no guarantee that it will become a mine. Mining companies have to spend a lot of time and money on due diligence, prefeasibility and feasibility studies, and sustainable development and environmental issues before deciding whether the deposit will become a profitable mine. And then there are the millions of dollars spent in developing the deposit and building a mine. No wonder the mining industry has trouble attracting investment capital. Companies take a large risk in developing reserves and investors take a similar risk in investing in them. So mining companies must be as accurate as possible in determining mineralization that makes it to reserve status. After all, reserves are a company’s most important asset and one of the critical factors analysts and funding sources look at when determining if a mine or mining company is worth the risk.

Jan 1, 2003

By B J. van Loggerenberg

The capital cost of major items of mining equipment is very high. The operating cost of such equipment is also high. It is therefore important that such expensive equipment is used productively. To this end mine management uses production data systems and management accounting systems to monitor events and provide data for analysis to enable management to make operating and business optimisation decisions. This could be done better if there was an understanding of productivity in terms of its utilisation and efficiency components. What has been missing has been a methodology to properly account for the productivity of equipment in terms of its contribution in dollars to the costs and profit of the mine. An explanation of the Productivity Accounting methodology will be given. It will then be shown that productivity has two components, that of capacity utilisation and efficiency. These are defined and the dollar contribution of each to costs and profit shown. The efficiency component tracks the effect of proportional changes in input cost quantities used in the mining process as mining production changes. The capacity utilisation component tracks the effect of step changes in the input cost quantities used in the mining process as mining production changes.

Jan 1, 2003

By D. G. C. Robertson

The thermodynamics and kinetics of the reactions involved in fuming zinc from oxide slags using coal or coke were first studied in 1955 and have been the subject of many investigations since that time. The key reaction is ZnO(in slag) + CO Zn(g) + COl. This paper will review the some of the recent work, and will add new insights obtained in experiments carried out by the authors. In the first series of experiments it was shown that the reaction 2Fe2+ + ZnO = 2Fe3+ + Zn(g) or 2FeO + ZnO = Fe2O3 + Zn(g) does not occur at an appreciable rate, as is expected from thermodynamic considerations. In the second series of experiments it was shown that zinc does not fume from the slag at a significant rate unless a reductant has been added. This again is in accord with thermodynamic considerations, but is in contradiction to some of the experimental results reported in the literature. A third series of experiments was carried out with excess coke being present, so that the rate of supply of reductant was not in any way controlling the rate. The kinetics of zinc oxide reaction were then found to be independent of the zinc oxide concentration, but increased with increasing basicity, and temperature. The presence of high concentrations of FeO in the slag also improves the kinetics. At low zinc oxide concentrations iron oxide reduction occurred in parallel with zinc oxide reduction. We propose that (under the conditions of this work) the kinetics were controlled by a chemical step, namely the rate of desorption of an adsorbed CO2 species. This is the same mechanism as reported by Belton and co-workers for the kinetics of the reduction of FeO. This explains why the reduction of metal oxides in slags by hydrogen is often faster than by CO.

Jan 1, 2003

By James P. Bennett

EAF slag chemistry and its control have been recognized as important in producing quality steel at a low price for a number of decades_ EAF steel producers make lime and dolomite additions to furnaces, controlling the CIS ratios and sulfur pickup from the steel. Existing phase diagram data at 1600°C for CaO, MgO, FeO, SiO2, and Al2O3 was used to write a computer model optimizing slag chemistry for slag foaming and reduced refractory wear. The model, its development, and its use in an industrial steelmaking environment will be discussed along with how the model can improve energy efficiency. The importance of EAF mass balance to account for critical materials like Si in scrap and refractory wear using the model will also be emphasized_

Jan 1, 2003

By M Simanjuntak, A M. Supomo

PT Freeport IndonesiaÆs copper/gold operation disposes of approximately 222 000 dry metric tonnes of tailings per day via two thickeners. Reduction of the flocculant dosage rates in each of the tailing thickeners has been achieved with the installation of Clarometers«, modifications to the existing operating DCS control strategy and a change in plant flocculant. This has reduced the flocculant consumption rate in the last twelve months by approximately 20 per cent. It has also highlighted the disparity in the settling rates of the two thickeners. Collaborative efforts between Cytec technical site engineers and Freeport operational personnel have made possible the overall gains achieved in the tailings thickener optimisation.

Jan 1, 2003

By Doug Halbe

?Many are called, but few are chosen.? The biblical adage applies not only to life, but also to hydrometallurgical processes. There have been, in the past, many outstanding successes with new processes ? and also some dismal failures. What are the odds of success for a new process? When there have been problems, why? What can you do to make sure these problems don?t occur with your process? What effect will a slow startup have on project economics? How do financial institutions ? the people who loan your company money for the project ? feel about new processes and why? Is it possible to predict or estimate the time required to reach design parameters?and if so, how do you sell this estimate to management ? and financial institutions? Probably most important ? when do you start thinking about the answers to these questions?

Jan 1, 2003

By Youngkook Lee

The precipitation kinetics of NbC in ferrite matrix of the Nb microalloyed steel was investigated experimentally and numerically. The mole fractions of NbC precipitates formed at different isothermal temperatures were measured as a function of holding time by electrical resistivity test and were compared with both a mathematical model based on time-dependent nucleation and growth rates and the hardness. There is a good match among the calculated and measured precipitation kinetics of NbC and the hardness. The isothermal precipitation-temperature-time diagram of NbC in ferrite matrix of the Nb microalloyed steel was newly generated. Keywords: Precipitation, Carbide, Ferrite, Nucleation, Growth, etc

Jan 1, 2003

By Benoit Clermont, Jan Lux

"Magotteaux and Anglo Platinum started a co-operation program with the main aim of establishing the optimum milling configuration measured in terms of throughput, fineness and energy consumption.For this purpose, a fully instrumented pilot milling plant, supplied by Magotteaux (Pty) Ltd, and equipped with a 0.9 x 1.0 m ball mill, was erected at Frank concentrator (Merensky Pt ore). The primary ball mills at Frank concentrator were surveyed in order to set the conditions for the base case. This data was then replicated in the pilot mill under the same configuration. Thereafter, a series of different parameters were varied in order to attempt to optimize the milling system.Only grate versus overflow discharge and open versus closed circuit will be discussed in this paper.It should be noted that this paper does not attempt to give a universal solution as to what milling configuration is optimum in all cases. The conclusions apply for this particular case and probably most others, but it would be advisable to consider each case on its own.CONCLUSION• Overflow versus grate dischargeAn overflow mill has a “pool” of slurry around the toe of the ball charge, which creates a counter lever to the ball charge. This will reduce the absorbed power in the range of 10-15% (depending on the case) and will consequently result in a coarser grind. The tests found a 4% gain in grinding efficiency (Wio) with an overflow mill but this is probably not significant.This lower absorbed power and coarser grind can be counteracted by increasing the ball charge (if below maximum) and/or by increasing the mill volume when removing the grate discharge (a typical grate takes up about 300mm of the mill length).• Open versus closed circuit"

Jan 1, 2003

By James P. Bennett

EAF slag chemistry and its control have been recognized as important in producing quality steel at a low price for a number of decades. EAF steel producers make lime and dolomite additions to furnaces, controlling the CIS ratios and sulfur pickup from the steel. Existing phase diagram data at 1600°C for CaO, MgO, FeO, SiO2, and Al2O3 was used to write a computer model optimizing slag chemistry for slag foaming and reduced refractory wear. The model, its development, and its use in an industrial steelmaking environment will be discussed along with how the model can improve energy efficiency. The importance of EAF mass balance to account for critical materials like Si in scrap and refractory wear using the model will also be emphasized.

Jan 1, 2003

By William E. Roscoe

"Valuation methods are well established for mineral properties with production or imminent production, and include discounted cash flow and comparable transactions. Valuation methods for non-producing mineral properties, however, are more subjective. Non-producing mineral properties include those at various stages of exploration, properties at the prefeasibility or feasibility stage, properties with currently uneconomic mineral resources, and past-producers. Different valuation methods may be appropriate for different types of mineral properties.Income approach methods such as discounted cash flow and option pricing are generally not applicable to properties at the exploration stage. The market approach is generally appropriate to all types of mineral properties, although it is difficult to find good comparables because of the unique nature of mineral properties and the small number of transactions. Cost approach methods, such as appraised value and geoscience factor, are commonly used for exploration stage properties.Canadian standards and guidelines for valuation of mineral properties are in the process of being finalized by a Special Committee of the Canadian Institute of Mining, Metallurgy and Petroleum (CIMVal Committee). The CIMVal Standards are intended to be consistent with National Instrument 43-101, which sets regulatory standards of disclosure for mineral projects, and with International Valuation Standards. The intent of the CIMVal Standards and Guidelines is that mineral property valuation be carried out by appropriately qualified individuals and that all relevant information be disclosed."

Jan 1, 2003

By M. C. Mound, L. Fradette, C. Colbert

Metallurgical Accounting in the mineral processing industry transforms accumulated process data, including flow rates and assays, into a coherent information format. This is used to rapidly provide production reporting and key performance indications. A fully comprehensive and coherency of available data must be a component of any system expected to accomplish reconciliation in the mass balancing process. Quality issues are thus improved with such desired methods via a mass-balancing engine utilizing the results of measurements acquired by various on-line sensors, analyzers, and sophisticated laboratory equipment. Metallurgical Accounting, when accomplished through such an engine, provides high value information in a simple, straightforward, and simplified manner. Exceptional utility is then transparently available to authorized personnel for access to metallurgical accounting reports, production reports, mass balance results, performance indicators, and so on. This paper discusses how such information can be used to "drilldown" into each result set by consulting the data hierarchy to evaluate and validate calculations and input data used to produce the specific results being queried. The power of such a system resides in the full and true integration of all production and laboratory data. What is integrated are the data thus acquired via a single user interface, a single database, a single configuration tool, etc. From this comes the derivation of contextual information and its maintenance. It is possible to reduce metallurgical accounting and production reporting from possibly hours or even days to a matter of minutes. The result is maximization of information reliability and availability from masses of otherwise discrete and difficult to access key data.

Jan 1, 2003

By G. J. Olson

This paper describes the microbiology basics underlying heap and tank biooxidation of metal sulfide ores and concentrates. The primary organisms are identified and described along with the reactions they catalyze and their growth requirements. Also described is the interaction between ore leaching bacteria and the leaching environment in terms of solution chemistry, temperature, and mineral precipitation. Specific factors and agents that stimulate or inhibit growth and activity of ore bioleaching will be identified. Some of these factors are organism-specific and others are generic for microorganisms that grow under acidic conditions. Current knowledge of the limits of bioleaching in terms of dissolved ions in leach solutions, pH, and temperature will be summarized.

Jan 1, 2003

"The Companion Policy is guidance and not law. It sets out the views of the Canadian Securities Administrators (CSA) at to the manner in which the CSA interprets and applies certain provisions of NI 43-101 and Form 43101F1. The Companion Policy references the CIM Best Practice Guidelines for Mineral Exploration, and the Mineral Resources and Mineral Reserves, and that they should be followed by Qualified Persons.COMPANION POLICY 43-101CP TO NATIONAL INSTRUMENT 43-101 STANDARDS OF DISCLOSURE FOR MINERAL PROJECTS This companion policy sets out the views of the Canadian Securities Administrators (the “CSA”) as to the manner in which the CSA interprets and applies certain provisions of National Instrument 43-101 and Form 43-101F1 (the “Instrument”), and how the securities regulatory authorities or regulators (the “Securities Regulatory Authorities”) may exercise their discretion in respect of certain applications for exemption from provisions of the Instrument. PART 1 APPLICATION AND TERMINOLOGY 1.1 Supplements Other Requirements – The Instrument supplements other continuous disclosure requirements of securities legislation that apply to reporting issuers in all business sectors. 1.2 Evolving Industry Standards and Modifications to the Instrument- Mining industry practice and professional standards are evolving in Canada and internationally. The Securities Regulatory Authorities will monitor developments in these fields and will solicit and consider recommendations from their staff and external advisers as to whether modifications to the Instrument are appropriate. 1.3 Application of the Instrument -The definition of “disclosure” under the Instrument includes oral and written disclosure. The Instrument establishes standards for disclosure of scientific and technical information regarding mineral projects and requires that the disclosure be based on a technical report or other information prepared byor under the supervision of a qualified person. The Instrument does not apply to disclosure concerning petroleum, natural gas, bituminous sands or shales, groundwater, coal bed methane or other substances that do not fall within the meaning of the term “mineral project” in section 1.1 of the Instrument. 1.4 Mineral Resources and Mineral Reserves Definitions - The Instrument incorporates by reference the definitions and categories of mineral resources and mineral reserves as set out in the Canadian Institute of Mining, Metallurgy and Petroleum (the “CIM”) Definition Standards on Mineral Resources and Mineral Reserves (the “CIM Definition Standards”) adopted by the CIM Council on November 14, 2004, as amended. 1.5 Best Practices Guidelines for Mineral Resources and Mineral Reserves - A qualified person classifying a mineral deposit as a mineral resource or mineral reserve should follow the CIM Estimation of Mineral Resources and Mineral Reserves Best Practice Guidelines adopted by CIM on November 23, 2003, as amended. These guidelines are posted on www.cim.org."

Jan 1, 2003

My topic for today is the Crown Minerals of the future. New work initiatives are underway and the organisational structure is being overhauled. These are not insignificant changes and in this paper briefly summarises these proposals. These new work initiatives and changes to the organisational structure will have implications for the industry as a whole and also for the way individual clients interact with Crown Minerals.

Jan 1, 2003

By George J. Tamara

The urban environment presents special challenges for the design and construction of earth retention systems. Complications arising from difficult subsurface conditions are compounded by the presence of urban infrastructure and existing and prior construction. The proximity of adjacent structures as well as intense prior use can cause special concerns including the potential for archeological artifacts or contaminated ground or ground water. Utilities and structures may be particularly vulnerable to the effects of ground movement, dewatering and vibrations. Difficulty of access, congestion and limited work areas may severely restrict means and methods of construction. Dewatering may be limited or prohibited because of concerns for disposal of clean or contaminated water, depletion of aquifers, drawing of contaminants to the site or dewatering induced settlements.

Jan 1, 2003