Search Documents

By Duclerc Fernandes Parra, Vijaya Kumar Rangari, Washington Luiz Oliani, Danilo Marin Fermino, Ademar Benevolo Lugao, Nilton Lincopan, Luiz Gustavo Hiroki Komatsu

Polyethylene is widely used for packing applications. Different grades of polyethylene, LLDPE and LDPE play a major role in the film blowing industry. The use of nanoclay in polymer matrices (non-polar) requires the use of a compatibilizer agent, ethylene graft maleic anhydride copolymer (PE-g-MA), which acts as a bridge for nanoclay-matrix-interaction. In our study, blown films of LLDPE, LDPE, and their blends were produced using a twin screw extruder. The combination of PEs as matrix, montmorillonite (MMT) and silver nanoparticles (AgNPs) intended to improve mechanical and thermal properties. Nanocomposites films with 1 wt% of montmorillonite and 0.5–1.0 wt% silver nanoparticles were prepared by blow extrusion and evaluated. Nanoclay intercalation/exfoliation degree was investigated by X-ray diffraction spectroscopy (XRD) and scanning electron microscopy (SEM). Mechanical and thermal properties were evaluated. The results showed optimum dispersion at intercalation/exfoliation levels for polyethylene nanocomposite (PENC), slight increasing in mechanical and especially improvement in thermal properties.

Mar 1, 2017

By Ramana G. Reddy, Yuxiang Peng

The long-term corrosion behavior of Haynes 230 (H230) alloy in MgCl2–KCl eutectic salt was evaluated at 1273 K for 500 h in Ni crucible in argon gas. The results showed H230 alloy has good corrosion resistance. In addition, corrosion was noted to occur by depletion of Cr, which was deposited on the Ni crucible. Based on the calculation of Gibbs energy of Ni-Cr alloy and exchange current density of Cr in MgCl2–KCl, the Tafel model was constructed to investigate the corrosion potential and rate. The galvanic corrosion can be explained as the predicted results were in agreement with the experimental data.

Mar 1, 2017

By R. H. Eric, P. Taskinen, A. Bhalla, P. Halli

Sustainable development requires less energy consumption with lower carbon footprint. In this review the solid state reduction behaviour of three oxide ores using methane gas are briefly summarized based on experimental work conducted in our laboratories. The discussion concentrates mainly on mechanisms of the reduction studied through SEM-EDAX and X-ray diffraction techniques. Limited preliminary kinetic input is also mentioned. Iron ore containing titanium and vanadium could be reduced significantly in the solid state with methane-hydrogen mixture up to 400 °C lower than is needed in ordinary solid state carbothermic process. The reduction of chromite and manganese ores were possible similarly at lower temperatures with potential energy savings lower carbon footprint.

Mar 1, 2017

By A. Rikos, G. Pantazopoulos, A. Vazdirvanidis, A. Toulfatzis

In this study, the mechanical properties of an annealed CuZn36 rolled brass alloy with 0.2 mm thickness with respect to anisotropy expressed in terms of plastic strain ratio measurements (r-values, normal and planar anisotropy) are related with the development of specific rolling and recrystallization texture components obtained by EBSD. Anisotropic behaviour is primarily controlled by the crystallographic texture and constitutes an indicator of multi-axial mechanical behaviour, affecting directly the drawability and sheet metal formability. Microstructure examination employing optical and Scanning Electron Microscopy of tensile specimens are performed in order to investigate the emergent damage mechanisms in relation to the texture and structure evolution of the final product.

Mar 1, 2017

By Raj K. Rajamani, James R. Nagel, York R. Smith

In this work, we examine the efficacy of Electrodynamic Eddy Current Separation (EECS) to recover valuable materials from end-of-life solar panels. Traditional rotary-based eddy current separators are capable of excitation frequencies of 1 kHz or less and struggle to economically separate particles smaller than 1 cm. A new design of eddy current separators has been developed at the University of Utah which has no mechanically moving parts. The design is capable of excitation frequencies up to 50 kHz, allowing sorting of particles as small as 1.0 mm. Recently, we have been successful in separating mixtures of Si/Al and CdTe/Al particles (1–3 mm) with recovery and grades greater than 85%, an energy demand of 68 kWh/short ton of sorted material, and throughput of roughly 10 kg/h. Current and future challenges utilizing this method for valuable material recovery from end-of-life solar panels are discussed.

Mar 1, 2017

By G. E. S. Lima, I. K. R. Andrade, N. G. Viana, R. O. G. Martins, L. M. Sathler, L. G. Pedroti, C. M. M. E. Torres, W. E. H. Fernandes, C. M. Silva, M. A. Caetano

In Brazil, kraft pulp mills are rapidly expanding and industrial waste generation is increasing. Technical feasibility of using solid wastes from kraft pulp mills as raw material in other industries may be an interesting approach to manage environmental and economic aspects of the industry. This paper proposes the incorporation, in different proportions (0, 2.5, 5 and 7.5%), of alkaline solid wastes from pulp mills, namely dregs and grits, to clinker in the Portland cement industry. The research was carried out in two steps: (i) characterization of dregs, grits and clinker; (ii) laboratory testing (determination of soundness by the Le Chatelier method, determination of setting times, determination of water content of the paste with normal consistency, determination of compressive strength and static modulus of elasticity). The results showed that the addition of dregs and grits to the clinker up to 2.5% were feasible according to the Portland cement Brazilian standards.

Mar 1, 2017

By T. F. Oliveira, E. B. Zanelato, J. Alexandre, L. J. T. Petrucci, A. R. G. Azevedo

The paper and cellulose industry is responsible for generating large amounts of solid waste, which are produced during various stages of the production process. Currently this material goes to places like landfills and other generating costs for the company. Furthermore, cement, mortar and concrete represent a significant economic and environmental cost. This study aims to determine the pozzolanic activity index in the residue studied to verify its viability in the incorporation of the same in cement. It will be used Luxan method for this determination. The data found show that the material has the possibility of being incorporated in the mortar due to its pozzolanic activity index.

Mar 1, 2017

By Zhenzhou Yang, Zuotai Zhang

In the present study, we proposed a method that using sewage sludge (SS) as alternative fuel and raw material to produce cement clinker. It was found that the increasing amount of SS can favor for the formation of tricalcium silicate (C3S) but the excessive amount can cause the impediment effect. Furthermore, SS contains high contents of trace elements, especially for zinc and manganese. The thermodynamic equilibrium calculation of Zn and Mn are also conducted to further understand their transformation behaviors and the results show that zine is predicted as a volatile element while manganese shows great condensed potential during the cement clinker calcination process.

Mar 1, 2017

By Michael Somerville, Paul Voigt, Chunlin Chen, Alistair Burrows

To date, many types of primary concentrate have been smelted using the ISASMELT™ technology, with annual smelting of copper concentrate alone exceeding 7 million tonnes. Most of this material could best be described as chalcopyrite concentrate, owing to the predominance of copper attributable to this single mineral. Chalcopyrite concentrates lend themselves readily to smelting with a fayalite slag, and producing a matte containing 55–65 wt% Cu. However, the ISASMELT™ technology also stands ready to meet future copper demand through the treatment of new types of concentrates containing relatively low iron and high silica levels. Various slag systems have been considered for direct-to-blister smelting. They have been evaluated computationally, using the MPE thermodynamic modelling package, and practically, at pilot scale. The lime-silica-iron oxide slag was found to have the lowest slag make, lower dissolved copper and hence lowest copper losses. Based on the outcomes of the modelling and pilot scale testwork a future smelter flowsheet has been defined, comprising a single ISASMELT™ direct-to-blister furnace, an electric slag cleaning furnace, and appropriately designed anode furnaces.

Mar 1, 2017

By G. O. Onyedika, M. U. Obidiegwu, G. C. Onuegbu

The effect of kolanut (KN) filler and compatibilizer (maleic anhydride) contents on the transport of toluene through low density polyethylene (LDPE) and low density polyethylene composite were studied at the temperatures 40, 60 and 80 °C.The kolanut powder used was ground to 25 μm particle size. In preparation of composite 0–5 wt% of kolanut powder and 0–2.5 wt% of the compatibilizer were mixed with 200 g of low density polyethylene in an injection moulding machine. The injected polyethylene and polyethylene/kolanut composites (LDPE/KN) were taken for sorption test. The sorption data obtained for low density polyethylene and kolanut powder filled low density polyethylene at the different temperature investigated were expressed as the molar percentage uptake (% Qt) of toluene per gram of the kola nut composites. Results show that the uptake of toluene at the five filler content (0–5 wt%) generally increased with increase in sorption temperature but decreased with increase in compatibilizer and filler contents. This can be seen at 80 °C and 0, 1, 1.5 and 2.5 wt% of compatibilizer respectively. The molar percentage uptake of toluene at 1 wt% of filler yielded the following values; 8.6789, 8.4768, 8.3476 and 8.2679 respectively. At 2 wt% it yielded 8.6224, 8.1333, 7.9525 and 7.9042 respectively, at 3 wt% it gave 8.4336, 7.9450,7.8900 and 7.7823 respectively, at 4 wt% it yielded 8.0263,7.9614,7.8218 and 7.6800 respectively and at 5 wt% it gave 7.9635, 7.8630, 7.6256 and 7.5013 respectively.

Mar 1, 2017

By Ruixuan Zhang, Yan Li, Shusen Cheng

The high temperature distribution of the blast furnace raceway plays an important role in continuous and steady production. There are a number of techniques which have been developed for flame temperature measurements, but most of them have considerable errors and instability. To obtain more accurate results, an efficient optimization algorithm is necessary. This paper presents a novel measurement approach based on the two-color method and an optimization algorithm using images of raceway flame captured by the RGB CCD (Charged-couple Device) camera to calculate the projection temperature distri- bution. Furthermore, both the back-propagation neural network and the principal component analysis are applied to calibrate the correlation between blackbody temperature and the gray-level intensity. Experimental results obtained from the blast furnace raceway demonstrate that the proposed optimization approach performs well in the measurement offlame temperature compared with the measured temperature.

Mar 1, 2017

By Ping Long, Jian Wu, Yaochun Yao

Atomic force microscope (AFM) is widely used for determining of surface performance of materials with smoother surface. In this research, atomic force microscope was used in morphology determination of powder material. Samples were dispersed in aqueous system by ultrasound wave and prepared on mica sheet. Multiple mappings of different powder samples, such as sintered products of ferrous oxalate, ferrous oxalate with lamella structure, lithium carbonate, boron powder, ferric oxide and zinc oxide, were investigated and analyzed in detail. Results showed as follow: ferrous oxalate sintered in different processes and conditions presented different morphology characteristics both in shape and size. Ferrous oxalate obtained from special process presented two-dimension lamella structure and self-assembly phenomenon. The shape and size of lithium carbonate particles were uniform. Defects of mappings on boron powder, ferric oxide and zinc oxide reflected problems of the preparation process before scanning. Determination experiences of powder material in AFM technology could be obtained.

Mar 1, 2017

By R. Padilla, M. C. Ruiz, L. Salinas

Chloridizing roasting of bismuthinite (Bi2S3) with NaCl–O2 has been studied to remove the impurity Bi by volatilization from copper concentrates that contain bismuthinite. The study was conducted using mixtures of Bi2S3 and NaCl in a horizontal furnace and TGA apparatus. The variables were temperature, oxygen partial pressure, and NaCl concentration. The chlorination was analyzed by weight loss measurement method. XRD results of calcines reacted for short times in 21% O2, and 850–1000 °C showed the presence of Bi, BiOCl, and Na2SO4, while at longer times in the same conditions, Bi2O3 was identified as a stable phase. Thus, the chloridizing-volatilization of Bi2S3 proceeds through the formation of Bi and BiOCl. Temperature affected significantly the fraction of weight loss of samples. At 600 and 900 °C in 10.3% oxygen, the maximum weight loss was 4 and 20%, respectively. An increment in the partial pressure of oxygen in the range 1–21% affected negatively the Bi2S3 conversion. At normal roasting temperatures (550–700 °C), bismuth volatilization by NaCl roasting was found to be marginal.

Mar 1, 2017

By Chao Li, Shi Sun, Hongxu Li, Jiaqi Fan, Liangtian Wei

Aiming at the recovery of copper from smelting slag, a flotation approach was studied. It was found that this slag composed of fine particles with complex association and distribution, in which bornite was the main copper-bearing mineral after a detailed mineralogy analysis via polarizing microscope, SEM and XRD. Consequently, flotation was attempted to recycle Cu in slag containing copper sulphide components. Three key factors affecting flotation were ascertained, namely, grinding fineness, the collector and the pH value, while the recovery of Cu estimated by ICP and XRF. Copper concentrate grading at 14.47 with 79.66% Cu recovery was obtained, in the condition of the grinding fineness of −0.074 mm and the proportion of 80%, reagent dosages of 50 g/t for butyl xanthate and a pH value of 10 adjusted using Na2CO3.

Mar 1, 2017

By M. A. Kader, W. D. Hutchison, M. A. Islam, P. J. Hazell, J. P. Escobedo, A. D. Brown

The effects of post-foaming thermal processing on the quasi-static compressive strength of closed-cell aluminium foam with an average relative density of 0.56 g/cc have been investigated. Samples were subject to one of four material conditions: as-received (AR), warm aged (WA), solution treated (ST), and annealed (AT). X-ray diffraction (XRD) was performed to determine a relationship between each material condition and macro-crystallographic texture of the dendritic α-Al phase. It was found that all heat treated samples contained clear deviations from random texture towards the exterior regions of the samples, indicating non-uniform recrystallization kinetics. The ST and WA samples exhibited the highest yield stresses and energy absorption, with the AT samples exhibiting the lowest. Additionally, it was found that the AR and WA conditions lost 12.8 and 15.6% of their total mass from brittle cell wall crumbling, whereas the AT and ST conditions lost 2.5 and 3.0% of their total mass.

Mar 1, 2017

By A. Arenas-Flores, Pandiyan Thangarasu, J. P. Hernández-Lara, F. R. Barrientos-Hernández, J. A. Romero-Serrano, A. Hernández-Ramírez, M. Pérez-Labra

BaTiO3 doped with Gd3+, was synthesized from BaCO3, TiO2, and Gd2O3 as powders using the solid state reaction method (Ba1-xGdxTi1-x/4O3). The milling of the precursors was performed in an agate mortar with acetone as control means and compositions x = 0.001, 0.005, 0.05, 0.15, 0.25, 0.35 Gd3+ (wt%). Firstly, the powder mixture was decarbonated at 900 °C for 8 h, after it was sintered at 1400 °C for 5 h. Tetragonality of synthesized BaTiO3 doped with Gd3+ was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Raman spectroscopy (RS). Subsequently, the powders sintered were uniaxially compacted cold until to obtain pellets of about 10 mm in diameter; which again were sintered at 1400 °C for 4 h. XRD patterns and Raman spectra results revealed that the crystal phase of the obtained particles was predominately tetragonal BaTiO3.

Mar 1, 2017

By Chaoying Ni, Dimitry Sediako, Prashant Karandikar, Sean Fudger

Neutron diffraction measurements were performed on steel encapsulated metal matrix composites (MMCs) in order to quantify bulk residual stresses. A coefficient of thermal expansion (CTE) mismatch induced residual compressive stress method is utilized as a means of improving the ductility of the MMCs and overall efficiency of several macro hybridized materials systems. Systems consisting of an A36, 304 stainless steel, or Nitronic® 50 stainless steel shell filled with an Al-SiC or Al-Al2O3 metal matrix composite are evaluated in this work. Upon cooling from processing temperatures residual strains are generated due to a CTE mismatch between each of the phases: steel, aluminum, and reinforcement. The analysis shows variation in the measured strain and stress results due to outer steel thickness, difference in CTE between materials, and relative position within the composite.

Mar 1, 2017

By Maria Rashidi, Maryam Ghodrat, Bijan Samali

Treatment of sharp medical waste (waste disposable syringes) produced in hospitals or health care facilities in an environmentally sound ways have raised concerns relating to public health and occupational safety. Life cycle assessment (LCA) is a decision-supporting tool in waste management practice; but relatively little research has been done on the evaluation of sharp medical waste treatment from a life cycle perspective. Our study assesses the environmental performances of medical waste incineration as a type of dominant technology for specific medical waste of average composition. Inventory models were used for waste incineration and residues land fill. Background data were derived from modelling performed in HSC Chemistry thermochemical package linked with GaBi environmental assessment tool. Two scenarios have been considered and compared: Waste disposable syringes partially replacing coke in Electric Arc Furnace (EAF) steelmaking (WSI) and conventional incineration with pure metallurgical coke without adding waste syringes (CI). The results of this study could support the medical waste hierarchy and indicate that from a life cycle perspective, replacing part of metallurgical coke with waste syringes in electric arc furnace steelmaking leads to fairly significant reduce in most of environmental impact categories.

Mar 1, 2017

By E. Salinas Rodríguez, I. Rivera Landero, E. G. Palacios Beas, J. Hernández Ávila, E. Cerecedo Sáenz, M. A. Mesinas Romero, M. I. Reyes Valderrama

For this study, a sample of 5 g of copper powders obtained by grinding printed circuit boards of computers fixe to 50 mesh (270 μm) according Tyler® series was used. This sample was wholly characterized by XRD, SEM–EDS and AAS. The leaching medium used wasO2S2O3 2. From the evaluated variables it was obtained an apparent order of the reaction of n = 2.34 s−1, whereas according the effect of partial oxygen pressure it was obtained an apparent order of reaction of n = 0.9516 and the activation energy of system was of 6.5 kJ mol−1, the results so achieved suggest a transport control to the solid–liquid interface. Under certain work conditions such as: S2O3 2 ¼ 0:5M, 500 mL, 750 min−1, P/PO2 = 1 atm, 338 K, 5 g of sample and 9000 s of reaction time, it is possible get up to 97.35% of leached copper.

Mar 1, 2017

By M. Firdaus, M. A. H. Shuva, M. A. Rhamdhani, G. A. Brooks, S. Masood, M. A. Reuter

Declining grade of primary ores and resource efficiency have led us to process more alternative metal resources such as e-waste. One of the processing routes for extracting valuable metals from e-waste is through the black copper smelting. However, the underlying knowledge of the thermodynamics behaviour of the valuable metals contained in e-waste during smelting are limited which prevent us from developing an optimised process to recover all the metals. These different metals clearly will have different favourable conditions for their extraction. To illustrate this, the distribution behaviour of germanium (Ge) and palladium (Pd) between liquid copper and ferrous-calcium-silicate slag during black copper smelting was analysed. It was demonstrated that oxygen partial pressure and slag composition affect the partitioning of these metals to the copper phase and the favourable slag chemistry for recovering these metals is opposing. Considering the available thermodynamic data of these metals, an analysis for the optimum conditions is presented.

Mar 1, 2017