Search Documents

By Michael J. Martinson

A powerful methane explosion in the mid-shaft pump station of a main service and ventilation shaft killed several persons on the station; more workers were killed when a mancage travelling down the shaft fell to the shaft bottom under a pile of broken concrete slabs from a brattice wall destroyed by the explosion venting into the shaft and a tangled mass of twisted steelwork from the equipped compartment. The newly-commissioned shaft serves a recent extension of an established mine on the Orange Free State (OFS) goldfield in South Africa. After outlining the circumstances in which the paper was written, and reviewing the nature and extent of the methane hazard in OFS mines, the paper describes the physical layout of the shaft and summarises evidence given by witnesses at the official inquiry concerning events prior to the explosion. No attempt is made to apportion blame for the incident.

Jan 1, 1989

By Keith G. Wallace, Daniel J. Brunner

The traditional approach to mine ventilation planning involved making estimates of airflows, including leakage routes, and summing the corresponding pressure drops along consecutive paths in order to determine the fan pressures required. This methodology changed completely with the availability of computers. Mainframe digital computers began to be used for mine ventilation network analysis in the mid-1960's. Their use spread rapidly throughout the world in the 1970's. Mainframe machines were employed owing to the need for high speed numerical procedures and substantial storage requirements. However, during the past decade, the growing availability of low cost but powerful microcomputers has allowed the development of net- work analysis programs that can handle ventilation systems of hundreds of branches, and which can produce results within a few minutes. This paper discusses recent advances in software and hardware development specific to mine ventilation planning. Software developments include interactive data and output manipulation, graphical representation of output, internal checks on input parameters to preset ranges and subroutines which calculate the gas distribution throughout the network from known gas sources. Hardware advances have led to significant increases in memory to facilitate the analysis of large ventilation models, math co-processor chips which greatly shorten run times, and plotter hardware for graphical output displays. Recent software developments make it possible to graphically display output on printers faster than on standard plotters.

Jan 1, 1989

By N. I. Jayaraman

Dust scrubbers on continuous miners are steadily gaining in popularity. Recent Bureau of Mines research on scrubbers is reviewed, with emphasis on the following areas: * Development of a new type of water-powered scrubber which can be retrofitted to existing miners. * Comparison of scrubber effectiveness with blowing and exhaust line ventilation. * Improving the quartz dust collection of flooded-bed' panels.

Jan 1, 1989

By J. G. Bensley, K. S. Detheridge

"Many plants use computers for process control and most have computerized Management Information Systems but few have been able to have these systems interact with one another. Developing this system interaction is not a one-step process but requires careful planning and implementation. This paper describes two projects that were implemented to provide the bridge between the process control and management information systems of Cominco Limited. Both projects include the replacement of essentially process control systems installed in the late 1960s. These original systems provided an enhanced level of control in the form of Direct Digital Control (via computer/manual analogue control stations) and a management reporting capability of process data. The experience gained from the use of these systems over a period of fifteen years formed a basis for the evaluation and planning for the new systems. The new systems were commissioned in 1985 and 1986 and operating and further developments leading to a totally integrated process information and control system are underway. INTRODUCTIONThe concept of hierarchical control involves a control structure consisting of a number of defined levels. Each level performs a defined function with information consolidated and combined as it moves up through the hierarchical structure. The commonly accepted structure of a hierarchical control system echoes the structure of the plant which is being controlled. Referring to Figure 1:Level 0 - Sensors and ActuatorsSensors and actuators, such as thermocouples and flow control valves, interface directly to the process and are generally connected directly to the controllers or multiplexers at Level I.Level 1 - Regulatory ControlThis level provides basic PID control (proportional/integral/ derivative) typically using microprocessor based controllers and programmable controllers for digital control of motors and machines. Systems at this levelare usually segregated by plant unit, e.g, crushing, flotation, drying. Control is concentrated on achieving optimum conditions for a particular feed rate."

Jan 1, 1989

The first principle one usually Learns about blasting is that cunpetence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced blaster when operating in a new area, may have to make one or two shots just to acclimate himself to the new conditions with which he is faced.

Jan 1, 1989

By D. R. East

The concept of sub-aerial tailings deposit.ion using a managed rotational deposition system to form a deposit of partly-saturated tails for North American conditions was introduced by Knight and described by Knight and Haile (1983). The application of the sub-aerial technique, together with continuous removal of all surface waters and underdrainage outflows from the Key Lake uranium mine I s tailing storage facility in Northern Saskatchewan, Canada, has been documented by Knight and Haile (1984). Since then, the concept is being applied in the United States to tailings facilities in California, Nevada, Arizona, Utah, Colorado, Idaho and South Dakota.

Jan 1, 1989

By Bibby P. A, Leupen R. A

A 24,300 tonnes per year state of the art Silicon smelter is being constructed for Barrack Silicon Pty Ltd at Kemerton, 20 kilometres north of the City of Bunbury in Western Australia. The plant is designed for the reduction of high purity quartzite lump to metallic silicon in two 27MVa Demag submerged arc electric furnaces. The primary reductant, a high purity charcoal, will be manufactured at the plant from locally sourced jarrah wood waste (Eucalyptus Marginata). Commercial silicon production is scheduled to commence in October 1989. Keywords: Silicon, Smelter, Quartzite, Furnace, Charcoal, Jarrah, Wood, Eucalyptus Marginata.

Jan 1, 1989

By J. D. Miller, Jon J. Kellar

Researchers in flotation chemistry have long sought to describe collector adsorption phenomena in greater detail including kinetics, orientation and interactions between adsorbed species. Now a quantitative description can be made in-situ using FTIR internal reflection spectroscopy. Details of the adsorption process at the surface of mineral crystals, machined into internal reflection elements, can be described from first principles, provided the refractive indices, incident angle, and wavelength of light are known. Collector orientation can be established based on spectral characteristics of plane polarized and perpendicular polarized light. Examples of the use of in-situ FTIR internal reflection spectroscopy are given for the sapphire-sodium dodecyl sulfate system and for the fluorite-sodium oleate system. It is expected that quantitative in-situ analysis of collector adsorption reactions by FTIR internal reflection spectro-scopy will continue to grow in importance and will provide an important new dimension in our understanding of flotation chemistry.

Jan 1, 1989

By N. C. Matheson

The West's Shell Pile has been used on sites with very soft ground conditions for over 60 years. Fibre reinforced precast concrete shells 900mm long are threadled onto an internal mandrel which can be extended according to the depth driven to attain the load bearing resistance. On completion of driving the mandrel is removed leaving the precast shells to form a permanent lining to the cast insitu concrete core. To give resistance to high contamination, a tar based epoxy coat is sprayed on the outside of the shells or a flexible PVC liner is installed inside the shells to protect the core. Fundamental to the resistance to contamination is the quality of the precast fibre reinforced concrete shell, the mix design and method of manufacture. A series of detailed laboratory experiments were carried out using samples immersed in concentrated acid and sulphate solution. The long term effects of exposure to contamination is recorded in the case studies of existing piles at two gasworks sites.

Jan 1, 1989

By R. A. Sharma

Neodymium metal was successfully produced by the reduction of Nd203 with Na in the presence of CaC12-NaCl melts by the overall reduction reaction Nd203 + 3 CaC12 + 6 Na ? 2 Nd + 3 CaO + 6 NaCl at -750°C. The metal produced was extracted from the salt media by dissolving it in a Nd-Fe alloy pool. The yield (percentage of theoretical neodymium produced) was found to depend on the salt composition and the mass ratio of salt to neodymium in the reactor. A yield of 95% was obtained with salt ratios as low as 3.5. Further decrease in the salt ratio below 3.25 decreased the yield. Stirrer position had little effect on yield; while increasing the temperature and placing fins in the reactor increased the yield. The Nd-Fe alloy produced was of as good quality as that produced using Ca reductant, and was suitable for direct use in producing General Motors MAGNEQUENCH? alloy for permanent magnets.

Jan 1, 1989

By Riggin P. R.

"IntroductionIndustrial Relations combines two very important relationships - employee relations and union relations.Employee relations always come into play when people are hired to perform tasks. Because mineral processing plants cannot be operated successfully without people, at least not yet, if they ever will be, employee relations must exist in an operatingplant.If the employees choose to be represented by a union, then a relationship with the union as an institution also comes into play. It is very important to note that unionization does not mean that the employee relationship is replaced by a relationship with the union. The latter is superimposed on the former, but it does not replace it. Similarities and overlaps in the two relationships will be present, some of which are of fundamental importance. Nevertheless, they are two different relationships and the reader should bear this in mind when reviewing those parts of this chapter which discuss unionization, collective bargaining, collective agreements, and work stoppages.These two important relationships, which we have chosen to combine and call industrial relations, have crucial roles to play in the social system which interrelates people performing the necessary tasks involved in the operation and maintenance of a plant. The technological organization - equipment, process layout and so forth - and this social system are interdependent and complementary. This chapter attempts to show that the potential level of effectiveness of both the technological organization and the social system depends on the recognition and nurturing of this nexus between them.Occupational health and safety and training are subjects for another chapter. But, both of these have been critical and longstanding employee relations topics . They are destined to take on added importance in the future. As issues in collective bargaining, they are also attracting increasing attention in all union relations. It is hoped that the reader will not isolate from industrial relations those topics which are being dealt with in another chapter. They are very much a part of it and we cannot refrain from making some reference to them."

Jan 1, 1989

By V. Castranova, K. VanDyke

"INTRODUCTION A soluble mediator has been described which is released from activated rabbit leukocytes and induces histamine secretion from rabbit platelets (Barbaro and Zvaifler, 1966; Siraganian and Osler, 1971). This factor has been isolated, characterized and named platelet activating factor, PAF (Bcnveniste et. al., 1972). PAF has since been chemically identified as l-0-alkyl-2-acetyl-sn-glyceryl-3-phosphocholine (Benveniste et. al., 1979; Demopoulous et. al., 1979).PAF is a lipid mediator of broad biological activity. It causes smooth muscle contraction, contraction of lung tissue and decreased FEV 1; while enhancing capillary permeability thus causing edema (Pinkard, 1983). In addition, PAF is a chemoattractant and can lead to inflammation.PAF has been reported to stimulate the release of lysosomal enzymes, leukotriene B,, and lipid metabolites from neutrophils (Smith et. al., 1983; Shaw et. al., 1981; Lin et. al., 1982; O'Flaherty et. al., 1984). The objective of the present investigation was to further characterize PAP-induced stimulation of granulocytes and to develop a bioassay, i.e. chemiluminescence, for screening PAF receptor antagonists and inhibitors of PAP-induced activation of granulocytes. The possible use of the chemiluminescence assay to monitor PAF synthesis by human granulocytes is also described.METHODSBlood was drawn from healthy volunteers into a blood storage bag containing CPD anticoagulant. Granulocytes were partially purified by dextran sedimentation and further purified by centrifugal elutriation as described previously (Jones et. al., 1980). Granulocytes obtained by this procedure were approximately 95 percent pure. The number of granulocytes in this preparation was determined using an electronic cell counter (Coulter Model Z1, Coulter Instrument Co., Hialeah, FL). Isolated granulocytes were used to monitor membrane potential, hydrogen peroxide and superoxide release, oxygen consumption, calcium uptake and, in some cases, chemiluminescence. Studies of PAF receptor antagonists were conducted using neutrophils isolated by density centrifugation. Briefly, blood was layered onto Mono-Poly-Resolving Medium (Flow Laboratories, McLean, VA) and centrifuged at 22 °C and 300 g for 30 min. Neutrophils collected from the second band of this gradient were at least 90 percent pure."

Jan 1, 1989

By Harrison R. Cooper

Composition data is needed as input for executing process control and management of particulate separation for flotation control. While requirements for composition data can be satisfied in many cases by manual sampling and analysis, automatic sampling and assay systems are now viewed as justified for all but the simplest or smallest processes. On-stream X-ray fluorescence analysis (XRFA) has satisfied requirements for the main portion of metalliferous sulfide ore flotation processes as XRFA technology evolved in reliability and sophistication from its beginnings in the late 1950's. In recent years, advanced on-stream analysis technologies have reached levels of development suitable for use in process control to increase efficiencies of important processes in mining and minerals industries such as coal fines flotation and industrial minerals beneficiation (particularly phosphate beneficiation) where XRFA methods have been inapplicable. Recent technical developments pertinent to use of advanced technologies as well as improvements to established on-stream composition analysis methods are discussed.

Jan 1, 1989

By J. M. Elegante

A belt drive attendant was working underground during his shift at the junction of two belt drives. He worked alone, but communicated with others at the mine by underground phone. At noon his shift foreman stopped by his workstation. At 2:00 p.m. he was contacted by phone by a fellow belt drive attendant. At 5:00 p.m., he was found dead by the oncoming evening shifter.

Jan 1, 1989

By Peters S. G, Beams S. D

CONCEPTS AND REGIONAL GEOLOGY The Charters Towers region holds many keys to the metallogeny associated with the complex geological development of eastern Australia during the Palaeozoic. Tectonic, magmatic and volcano-sedimentary depositional episodes can be identified and related to the chronological development of batholithic host rocks (Clarke & Paine, 1970; Henderson, 1986; Murray, 1986). Pre-batholithic basement rocks in the north (Charters Towers Metamorphics) consist of a package of amphibolite grade schists interlayered with and intruded by gabbros and diorites (Peters, 1987). To the south (Seventy Mile Range Group) greenschist facies Cambro-Ordovician rocks overly some of the basement. The lower age of this basement is not constrained, parts of it could be as old as Pre-Cambrian. Mid-Ordovician (approx. 470 my) to Lower Devonian (approx. 400 my) age I-Type granitoid plutons of the composite Ravenswood batholith intrude the pre-batholith basement and the Seventy Mile Range Group. Igneous activity was initiated again in the Carboniferous with the extrusion of rhyolitic lavas and pyroclastics associated with porphyry and high-level intrusive complexes (Wyatt et al., 1971). The Ravenswood block is bounded by Devonian and Tertiary sedimentary sequences of mainly continental provenence.

Jan 1, 1989

By S. S. Gajin

The paper deals with parametric vibrations of an axially loaded pile. The dynamic model is derived by means of Hamilton's principle and reduced to a partial differen­tial equation with variable coefficients and corresponding initial boundary conditions, taking into account the influence of the axial force. By means of Galerkin's method, the partial equation is further reduced to a Matheu-Hill's matrix partial differential equation of the second order. Since the problem of the dynamic stabili­ty has been expressed only for standing piles, the paper analyses in detail two stan­ding piles, one which is restreined, whereas the other is hinged at the toe. In both cases it is assumed that head horisontal displacement is prevented. Using Ruunge-Kutt's method, a computer analysis in the time domain is given for the characteristic parameters and possible boundary conditions. The paper analyses the stationariness of the process, as well as the dependance of the critical excitation frequency upon the pile parameters. The results have been illustrated by respective diagrams.

Jan 1, 1989

By D. Mohan

Soft to medium dense silty and clayey soils are found in many parts of India and conventional friction piles have normally been used for foundations of high rise buildings and other structures on such soils. The author investigated the use of Bored Compaction Piles and these have been used on these soils achieving substantial economies in cost over conventional friction piles. Similarly highly expansive clays, commonly known as Indian Black Cotton Soils occupy about 20 percent of the Indian land area. Short bored underreamed piles have been developed for such soils and a very large construction of various types of buildings and other structures have come up on such piles over the last thirty years in various parts of the country. The paper describes investigations leading to the design and development of both these type of foundations.

Jan 1, 1989

By W. L. Cornell

The Missouri Pb ores are the only domestic Co resource being mined and processed for other metals; therefore, they present a viable short-term opportunity for Co production. Lead, zinc, and copper concentrates are produced from the ore. The Cu concentrate can contain up to 30 pct Co and the Pb concentrate up to 15 pct Co. Since Co is detrimental to the processing of the Zn concentrate; the remainder of the Co is rejected to the tailings. The tailings can contain as much as 50 pet Co originally present in the mined ore. Researchers at the U.S. Bureau of Mines have successfully tested on a continuous basis a process that recovers a bulk sulfide concentrate from mill tailings. The concentrate contains up to one-half of the Co and from 50 to 90 pct of the Pb, Zn, and Cu. Concentrate weight represents 10 pet or less of the total tailings.

Jan 1, 1989

By Leszek Hoser

Polycrystalline oxide superconductors that have the perovskite structure, that are oxygen deficient, and that have compositions based. on the so-called. 1-2-3 (YBa2Cu3O7) compound, were investigated.. The materials exhibit a high critical transition to superconductivity at temperatures near 90oK. It was determined that maintaining the oxygen content within the correct range in connection with an appropriate amount of CU ions in the crystal lattice leads to high-critical temperature (Tc:) superconducting properties. High-Tc: superconductors with a critical temperature in the range of 100°K were developed. Further investigations, based. on the theoretical examinations of the origin of superconductivity, have been performed and are discussed..

Jan 1, 1989

By Junbiao Liu

Rutile is mostly produced from placer sands. Its beneficiation from primary deposits has rarely been investigated. However, there is interest in primary deposit because of the depletion of sand deposits. The Zaoyang deposit in China is the only rutile primary deposit currently mined. The plant employs a Tabling-Magnetic process which recovers only 20% Ti02 at a grade of 87%. This study shows that significant improvement on the recovery (52% at the same grade) can be achieved. This study includes a detailed mineralogical examination and the development of a processing flowsheet of the ore. The gangues are primarily amphiboles, garnets, zoisites, and chlorites. The liberation of rutile occurs at about 200 mesh. Gravitational, flotation, and magnetic separations are all employed in the process developed, depending on the mineral characteristics and experimental results. The flotations circuit utilizes benzyl arsonic acid to float rutile and sodium fluosilicate to depress the gangues. This is a new reagent scheme for rutile flotation.

Jan 1, 1989