Search Documents

By Patrick J. Hannigan

A comparison of 40 statically and dynamically load tested piles was performed to evaluate the variation between testing methods. This evaluation indicated an agreement of 10% to 15% could be obtained when the available static resistance is fully mobilized by both methods and when time dependent capacity changes are minimized. Dynamic pile testing recommendations for minimum induced impact force, ram weight to pile weight ratio, and considerations for time dependent capacity changes are presented.

Jan 1, 1987

By R. Mittler

Over 100 saprolite samples from Turkey Hill Gold Mine, Lumpkin County, Georgia, were analyzed (-80 mesh) for As, Au, and Sb. Maximum values are 16.2 ppm As, 7.9 ppm Au, and 29.1 ppm Sb. Results show trace element content of saprolite varies with topography: ridge top samples show a pronounced decrease in Au and Sb, and to a lesser degree in As, whereas, slope and valley samples have anomalous Au and Sb concentrations, with no discernable pattern for As. Statistical analysis shows strong correlation between Au and Sb and none between Au and As. This study will serve as a model for gold exploration in deeply weathered terrains with variable relief.

Jan 1, 1987

By Davidson JR, Napier-Munn TJ, Kojovic T

A research program was conducted to determine the relationship between operating conditions and medium losses in Mt Newman Mining's Beneficiation Plant. It was found that major medium losses were adherence losses and losses fran the overflow from the water recovery cyclones. Operating density and medium blend were found to have a significant effect on the medium consumption. Viscosity was thought to be the underlying factor. This viscosity problem was overcame by adding dilution water to the cyclone spigot discharge to reduce viscosity. The result was a reduction in medium consumption of 25 percent under normal operating conditions. Keywords:- Heavy Medium, Viscosity, Medium Carposition

Jan 1, 1987

By Henry R. Tiedemann, William H. Hansmire, Harvey W. Parker

Although the use of precast concrete segments for tunnel linings has been common for many years in Europe, acceptance of this type of lining has been slow in the United States. This paper explores the cost, design, and construction considerations of concrete segmental lining with a view to promoting its use in this country when favorable conditions exist. The different perspectives held by owners, designers, and contractors are discussed. In addition to cost, other considerations include previous design and construction experience, size, length and function of tunnel, watertightness, and liability. Cost comparisons are made to traditional ground support and lining. Under favorable conditions, the use of precast concrete segmental linings can be technically feasible and cost effective.

Jan 1, 1987

The Dizon open pit mine of Benguet Corporation in western Central Luzon, Philippines has yielded some 182 000 t copper, and about 26 000 kg gold and 48 000 kg silver as by products since it started operation in November 1979. The 140 million tonne orebody is associated with a small quartz diorite porphyry stock emplaced in volcanic rocks on the basal slope of a stratovolcano complex as stockworks, fracture fillings and disseminated sulphide mineralization averaging 0.43% Cu, 0.93 g/t Au and 2.5 g/t Ag. Intense hydrothermal alteration accompanied the mineralization that developed fairly distinct mineral assemblages within and around the intrusive. Post-ore volcanic activity later gave birth to an upward-flaring diatreme which broke out south of and adjacent to the orebody and partially destroying it. Subsequent volcanic activity buried the mineralized area along with the rest of the stratovolcano's surrounding slopes under a thick deposit of pyroclastic and laharic debris. Erosion eventually removed the volcanic cappings over Dizon and also exposed the quartz diorite porphyry stock which might have resulted in the truncation of a sizeable section of the Dizon deposit. The chain of stratovolcanoes that comprise southeastern Zambales range hugging the southeastern edge of the Zambales ophiolite is part of a west-facing volcanic arc that extends for some 300 km along the western margin of central and southern Luzon whose development has been correlated to the subduction in the Manila Trench located off the west coast of Luzon. Prominent WNW-trending lineaments that cut across the ophiolite appear to be splays of the Philippine Fault whose intersection with the Mt. Pinatubo stratovolcano complex might have localized the emplacement of a number of intermediate stocks along with the gold-rich porphyry copper mineralizations associated with some of them.

Jan 1, 1987

By Christopher Mark

A new method for the design of longwall pillars, called "Analysis of Longwall Pillar Stability" (ALPS), is described. The method is the final result of a research program that included two major field studies, extensive reanalysis of data from other in situ measurements, and detailed evaluations of available pillar design methods. The key problem addressed by ALPS is estimation of the abutment loads applied to longwall pillars. Based on underground stress measurements made in mines in three states, equations for predicting the magnitude, distribution, and time-of-arrival of abutment loads are proposed. Stress measurements are also used to evaluate empirical pillar strength formulas for use in longwall pillar design. ALPS has been verified by application to case histories from several mining areas, and examples taken from the Pittsburgh and the Blue Creek seams are presented. Step-by-step guidelines for using this design method are also given.

Jan 1, 1987

By A. J. Reynolds

In recent years, rapid depletion of the higher grade reserves, allied to decreases in paylimits, has led to the exploitation of secondary, erratically mineralized placer horizons on various marginal and low grade gold mines. On Blyvooruitzicht Mine, the rich Carbon Leader Reef has limited reserves, necessitating exploration of the lower grade Middelvlei Reef. This placer has always presented evaluation and exploration problems, to such an extent that it was, at one stage, considered uneconomic. Despite an extensive underground drilling programme no ore reserve targets of reasonable size were apparent. However, when a certain degree of parallelism between sedimentological trends in the Middelvlei Reef and the underlying Carbon Leader was recognized, a meaningful exploration model could be developed. Firstly, all historical sampling records for the Carbon Leader were entered into a computerized system; the database comprised in excess of 340 000 data points. Variables captured consisted of gold value, uranium value, con- glomerate thickness and total reef thickness. The raw data were then averaged into blocks, and plots of different variables were computer-generated for further analysis. This enabled the Carbon Leader to be modelled sedimentologically and, thereby, exploration targets for the Middelvlei Reef were generated, based on the Carbon Leader facies trends. Geostatistical analysis of sampling data in exposed areas of the Middelvlei Reef underground has confirmed the sedimentological breakdown of the placer into distinct facies areas. A facies model relating value distribution patterns to depositional trends, both for the Carbon Leader and the Middelvlei Reef, has thus been incorporated into a mine planning strategy.

Jan 1, 1987

By Matsuo T, Uga Y

The tunnelling work to construct a sewage trunk line designed by the Sewage Bureau of Kobe City along north side slope of Rokko mountain range incorporated an all ground condition type (broad spectrum) TBM with slurry transport system with jet pump manufactured by Kawasaki Heavy Industries, Ltd. Boring dia. of the tunnel measured to 2.0 m. The construction planning and implemen- tation were done by Ohbayashi Corporation, the general contractor. The heading way was 3342.4 m in overall length.; construction work ran from April '84 to June '85. The max. daily progress marked 31.9 m and the max. monthly progress 493.1 m according to the relevant record. The machine proceeded with the work under geological conditions featured with conglomerate, rhyolite, tuff breccia and slate, whereby soft soil zone mostly of clay was encountered in a limited area. In the latter case, however, steel segments were substituted for supporting steel ribs. The tunnel was routed beneath a meandering road with the result that more than 40% of overall length show a curvature of 50 to 200 m radius.

Jan 1, 1987

By Michael von Seebach

High-pressure grinding rolls subject the feed material to pressures of 200 N/mm? During this process considerable size reduction and the Formation of flakes occur. This paper describes the basic consideration For design and operating of this type of mill. It is also shown that the particle size distribution resulting from this process is typical for grinding processes but untypical for crushing processes. High pressure grinding rolls are designed in size of up to 2.8 m roll diameter allowing feed material top sizes of 250 mm. The rigid frame, bearing and drive - train design allows a broad application of the high-pressure grinding rolls operating the machine in open or semi-closed and closed circuit for dry and moist feed materials. Operating results show that capacity increases of up to 100 % can be accomplished with this technology. The high-pressure grinding roll also, allows for lower operating and maintenance costs due to energy savings of up to 20 L and reduction of wear to less than 1 76 for dry and less than 0.1 5 for wet grinding. Other advantages of the high-pressure grinding rolls are smaller equipment sizes than a ball or SAG-mill for a given capacity resulting in lower building sizes with reduced capital in- vestment costs.

Jan 1, 1987

Australia has a high level of research and development capabilities in government, industry and tertiary institutions. In the- remote sensing fields, we have developed a range of applications in geology, agriculture, infrastructure and environmental monitoring which are very cost effective and applicable to projects in the Asian and Pacific region. Support by the Department of Science through the Scientific Industries Steering Committee has enabled rapid penetration of this technological capability into projects with significant economic and financial benefits. It has also led to the opportunity for development of new sensors and processing systems, through collaborative projects with regional countries, which. will have applications in cloud covered, rainforest, and coastal tropical regions for geological and resource applications.

Jan 1, 1987

By Slavoljub D. Maksimovic, Steve J. Page

The Bureau of Mines measured respirable dust emission rates from overburden drilling at a surface coal mine and the transport of this dust to downwind locations. The emission rates were estimated by using multiple gravimetric dust samplers mounted on a cross-shaped tripod located immediately downwind of the drill. The transport of this dust was measured at more distant downwind locations by a combination of respirable gravimetric sampling and integrated bag sampling of sulfur hexafluoride (SF6), which was used as a tracer gas. Two modes of sampling were used: (1) At five sampling locations arranged in a semicircle around the drill. The radius of this arc ranged from 15.85 m (52 ft) to 71.32 m (234 ft). (2) In-line sampling at downwind locations with samplers located at intervals of either 10.67 m (35 ft) or 15.24 m (50 ft) for a total distance of 76.20 m (250 ft). Samples were taken 1 .22 m to 1.52 m (4 to 5 ft) above ground level. Test results for the semicircular test arrangements showed that at any downwind location, the maximum contribution of respirable dust due specifically to the drilling operation was 42%; the average for eight tests was 13.6%. In general, there was no correlation between the downwind distance of this maximum contribution and the maximum contribution itself because of changing wind direction. Test results for the in-line arrangements indicated that the transport of the dust from the drilling operation usually decreases rapidly with distance and that, even though the drill dust may produce significant health hazards for the drill operator and drill helper (or other personnel in the immediate vicinity), the exposure of downwind personnel to drill-generated dust may not be a significant problem.

Jan 1, 1987

By Kaji S

The Tsugaru Tunnel, located on the Honshu island approach to the Seikan Tunnel, is 5,880 m long and has a "Shinkansen" cross section of 90 m2 area. The geological formation through which the tunnel passes consists of very soft rock most of which is unsolidified sandstone belonging to the Neogen. The permeability coefficient is in the range of 10-2 to 10-4 cm/s and being water bearing with a high ground water level, the ground is unstable and subject to soil outflow phenomenon. Kajima Corporation, undertaking the Futamata Construction Section (1,420 m long), excavated the tunnel by the upper half heading method with side pilots employing the following countermeasures to cope with these severe conditions.

Jan 1, 1987

By Tracy T. Morris

The current state of the mining community has made it imperative for operations to reduce costs and increase productivity in order to remain competitive. This has been done in Colorado with the installation of an Outokumpu flash flotation machine for the production of a gold/silver/lead concentrate.

Jan 1, 1987

By Jeff Schwoebel, Arcy, D&apos Horner

The Deep Coal Seam Project is a multi- year, large-scale research and development effort between the Gas Research Institute (GRI) and Resource Enterprises, Inc. (REI). The project is being conducted at the Red Mountain Site, a multi-well test site located in the southeastern portion of the Piceance Basin near Collbran in Mesa County, Colorado. The project objective is to develop the drilling, reservoir evaluation, completion and production technology required to produce gas from a thick, deeply buried coal seam. To understand the parameters controlling gas production, project efforts are focused on the Cameo "D" coal reservoir which lies at a depth of about 1707 m (5,600 ft) at the test site. This paper overviews the drilling, testing, completion, and production techniques used on the 1, 2 and 3 Deep Seam wells and implications for resource development.

Jan 1, 1987

Control dust generated during overburden drilling at surface coal mines using either wet suppression or dry collection systems. Approach For the wet suppression systems, a range of water flow rates was tested over a number of holes. Each hole was drilled at a specific and constant flow rate. A recording flow meter was mounted in the water line near the control system pump. For the dry collection systems, each drill was tested with the front of the shroud set at different heights above the ground. Because of the irregularity of the ground surface, all height measurements were taken at the front of the shroud. Background Wet drilling systems consist of a water tank mounted on the drill from which water is pumped into the downhole air line. The water droplets in the bail air conglomerate dust particles as they travel up the the annular space of the drilled hole, thus controlling dust as the air bails the cuttings from the hole.

Jan 1, 1987

By F. Garacia, J. Cervik

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of a discharge pipe. These measurements are erroneous and tend to be high by as much as 30 pct. The Bureau of Mines deter- mined method factors (correction factors) for anemometer measurements taken in this manner. Method factors for 4-, 6-, and 8-in (10.2-, 15.2-, and 20.3-cm) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By I. Toromanoff, F. Habashi

The transformation of a low-grade titanium slag into synthetic rutile or synthetic anatase can be enhanced by attrition grinding.

Jan 1, 1987

By A. Ward, A. Smith, D. Harpley

Methods for the prediction of seepage quality from waste-disposal facilities are evaluated for input to the design of desalination treatment facilities. This is done by reference to a waste dump seeping into a near-surface aquifer, the contaminated seepage being collected by scavenger wells. As the quality of contaminated water intercepted by the wells will vary with both space and time, it is necessary for predictive methods to accommodate such variations. One-dimensional and two-dimensional predictive solute transport models are described and applied to the seepage and scavenger-well example mentioned above. The advantages and disadvantages, interims of overall applicability, data requirements, and possible accuracy, are described and discussed. While one-dimensional models have the advantages of speed, simplicity, and cost, the frequent requirement of prediction in both space and time necessitates more complex, two-dimensional simulation.

Jan 1, 1987

By R. R. Smith

The meaning of the title, "Blank Piece of Paper," refers to the need for management to take a completely fresh viewpoint to the problems facing our industry. These problems are so severe and some so new that conventional thinking may not be adequate to resolve them. Innovation has to be a part of every company's approach to the solutions, our concept is to start with a "Blank Piece of Paper.' The objective of 'this paper is to outline steps which can be taken to improve the profitability of a mining business. This is not an examination of technical solutions to individual problems, but rather recommendations for overall change in management thinking. This philosophy is based on our actual, hands-on experience in major open pit operations worldwide over the past 25 years.

Jan 1, 1987

By C. M. Davidson, D. J. Drexler

"Sulphuric acid treated with hydrogen peroxide to destroy organic contaminants could conceivably show increased corrosivity toward carbon steel shipping and storage vessels, caused by the persistence of a peroxide residual. This paper describes work performed to determine the effect of 0-200ppm hydrogen peroxide on the corrosion of carbon steel by 93% and 98% sulphuric acid at room temperature (23ºC) and 50ºC.Steel electrodes were exposed to acid containing several peroxide levels (0. 45, iOO and 200 ppm) for up to two weeks. Specimens were removed at intervals and weight loss, open circuit potential, depth of metal loss and residual peroxide concentration recorded.Hydrogen peroxide decomposes considerably over two weeks in iron-contaminated sulphuric acid. initial peroxide concentrations > l00 ppm suppress corrosion, but the effect is lost when concentration decays below about 60 ppm. Sustained peroxide levels in the range below 60 ppm may increase corrosion rates. These phenomena are interpreted by analogy with anodic passivation."

Jan 1, 1987