Search Documents

By P. Campbell, E. M. Gardy, L. Hachkowski

Introduction The efficient process control of a uranium mill and its associated mining operation requires a nearly continuous knowledge of the uranium concentration in the ore. Generally, the approach is to use laboratory assays of grab samples from the mill feed belt. In some cases, elaborate and expensive systems have been used to ensure random sampling, but even with these systems, mass-balance discrepancies still exist. There is a requirement for an on-line instrument that can give a prompt, accurate analysis of a large portion of the feed stock. The authors have recently evaluated a laboratory system that achieves these goals using neutron activation and delayed neutron counting. The development of the on-line uranium ore analyzer is a consequence of previous work done at the Whiteshell Nuclear Research Establishment (WNRE) (Campbell et al., 1978 and 1981), and is based on the emission of delayed neutrons after the neutron irradiation of fissionable materials. The mechanism of delayed neutron emission has been described (Keepin, 1965), but briefly is as follows. The fission fragments resulting from irradiation are in an excited state. Certain of these delayed fission products, precursors, decay to a more stable state by the emission of a delayed neutron. The delayed neutrons can be divided into six groups with effective half-lives ranging from 0.2-55 sec. It is important to note that more than 50% of the delayed neutrons are emitted within the first 6 sec after irradiation; this has an influence on the design of the analysis instrument. Measurement Cycle The measurement cycle involves a neutron irradiation, a delay time, and a counting period. The laboratory demonstration model of the ore analyzer comprises a californium-252 neutron source, a source chamber, a pneumatic transfer facility, and a neutron irradiation and counting module [(Fig. 1)]. The ore sample is placed in the irradiation chamber. The neutron source is transferred to the center of the chamber for a 5-sec irradiation while the helium-3 thermal neutron detectors are switched off. As the source returns to the storage chamber, the detectors are switched on and the delayed neutrons counted. The total assay cycle is 16 sec. The current instrument design calls for the ore to be cut from the main belt every 16 sec by a mechanical arm and dropped into the analyzer directly, or via another belt. The cycle starts when there is a sufficient mass of ore in the irradiation chamber to depress a switch and stops when the delayed neutron count is finished. The ore is then dropped through the bottom of the analyzer chamber and returned to the main belt. The counts from each cycle are accumulated and the data reduced to give the desired information.

Jan 1, 1985

By T. K. McCranie, A. H. Tousley, A. H. Kackman, L. R. Gregory, A. Jr. McElrath, R. J. Krekel

In Roman and earlier civilizations the term cement was applied only to mixtures of lime, pozzolana, sand, water, etc., used as a mortar to bind larger stones. Today, portland cement, the subject of this section, can be briefly defined as follows: The product obtained by finely grinding clinker produced by calcining to incipient fusion (i.e., sintering) an intimate and properly proportioned mixture of argillaceous and calcareous materials. History The Egyptians were probably the first to join building stones with a mixture of sand and a cementitious material (i.e., having the property of or acting like cement). It is generally accepted that the cement used by the Egyptians on such structures as the Great Pyramid was calcined gypsum, Later the Greeks began to calcine limestone for use as a mortar with sand and water. Still later, broken brick and tile were added to the mortar to make the first concrete. The Greeks and Romans found that some sands produced mortars that were especially resistant to the action of water. Hydraulic (i.e., underwater-hardening) cements formed by combining slaked lime, water, and finely divided siliceous materials (e.g., pozzolana) possess superior strength and are capable of resisting the destructive action of water. They were used on the Pantheon, Colosseum, and other structures, some of which are still standing. In 1756 an English engineer, John Smeaton, found that an argillaceous limestone (i.e., containing an appreciable amount of clay as an impurity) produced a cement with greater resistance to the action of water. Despite Smeaton's findings, the use of the old mixture of lime and pozzolana long retained its popularity. Significant contributions in cement technology from England, Swe¬den, France, and Holland were made in the next 68 years. However, the invention of portland cement is generally credited to Joseph Aspdin, an Englishman, who in 1824 patented "portland cement." The name was selected because, on hardening, it resembled the natural building stone from the Isle of Portland, England. The patent features mixing ground limestone and argillaceous materials in appropriate proportions and calcining (i.e., expelling CO2 by roasting) the mixture. This superseded the existing practice of calcining naturally occurring argillaceous limestone. In about 1845 Isaac Johnson, also English, conducted experiments on proportioning the components and calcining them at higher tem¬peratures. His accomplishments are accepted as the beginning of the present-day portland cement industry. The U.S. cement industry originated with the demand for good hydraulic cement for building structures such as the Erie Canal, which was started in 1817. The first discovery of cement rock (i.e., naturally occurring argillaceous limestone with near-optimum ratios of calcium carbonate, alumina, and silica) near Fayetteville, N.Y., was made by C. White. In 1818, White secured a patent for the manufacture of natural cement from that deposit. Subsequently, several natural cement plants were built in 1830-1840 at Rosendale, N.Y., and in the Lehigh Valley of Pennsylvania. David Saylor, who participated in establishing a natural cement plant at Coplay, Pa., in 1850 discovered that a superior cement could be produced by calcining the rock at higher temperatures than hith¬erto. In 1871, Saylor obtained a patent and commenced the manufac¬ture of portland cement. By 1890, there were 17 portland cement plants in the United States with a combined annual output of 62,300 tons. At the end of 1970, the number of plants producing portland cement in the United States (including Puerto Rico) was 169, down from a maximum of 185 in 1967, with total annual shipments of 73.4 million tons valued at $1,298 million. (Fig. 1). In 1970, annual world production of hydraulic cement (which includes pozzolanic materials, hydraulic limes, natural cement, alumina cement, and portland cement, all of which are in current use in various parts of the world) reached 630 million tons (Table 1). Flowsheets of typical U.S. cement plants are shown in Chapter 13. Chemical Composition and Physical Properties It is generally accepted that portland cement clinker consists of a mixture of compounds or synthetic minerals. The four principal compounds are:

Jan 1, 1985

By T. C. Bibb

Longwalls using shearers in seam heights of less than 1.2 m (48 inches) are relatively rare in the U.S. Westmoreland Coal Company is currently operating a shearer-equipped longwall at a cutting height of 1.17 m (46 inches) in its Bullitt Mine. This face has averaged 2795 metric tons/day of operation since its startup on April 3, 1984. Longwall productivity in thin seams is substantially impacted by equipment reliability and availability of useable working room for travel and access. This paper addresses the design criteria used in selecting this face equipment, with the goal of maximizing these two parameters. Equipment discussed includes shearers. face conveyor, shields, stageloader, and emulsion system.

Jan 1, 1985

By T. E. Kobrick

When Ralph Banks called and asked if I would agree to present a paper on environmental health in the coal industry, I was reluctant because I have not been actively involved in coal mine dust control on a day-to-day basis for a number of years. Ralph reminded me that I am one of the few industry people with an industrial health background who remembers the pre-1969 Federal Coal Mine Health and Safety era. This marks the second time within the past year that I have had a similar request based on the same basic reasons. While I was pleased to have been remembered, I'm beginning to feel like the football player who has played one too many games. In responding to Ralph's request to present an overview of the past, present and future of environmental health in the coal industry, I have attempted to take the broad approach of someone who, having been intimately involved in an area of endeavor for a number of years and then leaves, has an opportunity to revisit that area at a later date to see what has changed and what remains the same, what have been the successes and the failures. Since none of us can foresee the future, trying to project too far ahead is fraught with frivolity, except that unless one is foolish enough to accept a future invitation to review those predictions compared to actual events, no one will recall how accurate or inaccurate those projections might have been. I can assure you that I will not ask to accept that challenge, so you can rest comfortably that five years from today you will not be asked to sit through a similar presentation by me - and that's a promise.

Jan 1, 1985

By Doyle P, Mulroney D

The Cassidy Shaft was sunk to access the Mount Charlotte and Reward Orebodies below the Flanagan Fault. The 1,184m deep shaft is concrete lined to 6.5m diameter for its full depth. The initial 590m was excavated by stripping into a 1.8m diameter borehole and hoisting the broken material through the existing mine. The remaining 594m was excavated by conventional shaft sinking methods. The shaft was sunk through 3 existing plats and an additional 8 plats cut. 1,800 tonnes of steel and 8 cables were installed during the furnishing of the 4 compartments.

Jan 1, 1985

By H. W. Schreiber, H. R. Babitzke, R. E. Rodriquez, Patterson J. A., C. D. Masters, J. J. Schanz, R. B. McCammon, E. A. Noble, P. M. Krishna

A five-year effort by the ASTM subcommittee E10.14 on uranium resource evaluation has culminated in the approval of E901-82, Classification System for Uranium Resources (ASTM Standard E901-82, April 1983). The standard classification was prepared with participation of representatives from the US Department of Energy, the US Department of Interior's Geological Survey and Bureau Mines, utilities, and consultants. The classification a resource is based on level of knowledge and the economic producibility of the resource at a given time. Alphanumeric identifiers are used rather than words to avoid confusion with existing terms, definitions, and classifications. An example demonstrates the dynamic nature of the process of classification and attests to the necessity of addressing both the aggregate needs of broad-scale resource planning and the specific needs of individual property evaluation. Problems that remain infixing the classification a given uranium resource include uncertainty in estimating the quantity of undiscovered resources and resolving differences that may exist in deciding when the drill-hole spacing is adequate to determine the tonnage and grade of discovered resources.

Jan 1, 1985

By Leo L. Van Sambeek

An understanding of the creep and yield behavior of salt is required for the rock mechanics design aspects of solution mining. Most previous studies of salt behavior have been performed on small specimens of salt under homogeneous stress conditions; i.e., uniaxial and triaxial tests on specimens <0.002 m3. The corejacking test is a larger scale test (-0.75 m3) with inhomogeneous stress conditions that provides data on the structural response of salt. Interpretation of the responses from eight such corejacking tests provides verification of the requisite constitutive parameters required to predict salt behavior at different levels of stress and temperature. These constitutive parameters are not those studied in the usual laboratory test. Corejacking test results show almost inseparable elastic and plastic closures simultaneous with the corejack pressurization. Very rapid closure (on a relative basis) continues for a period of time after the pressurization. This rapid closure is shown to be both continuing yield deformation and creep deformation. After the period of rapid closure, the closure rate approaches a constant value. Numerical modeling of the corejack tests using a creep law containing both transient and steady-state creep functions does not provide results that agree with the responses measured in the corejack tests. Using an experimental design technique plus additional numerical modeling that includes yielding of the salt, results in identification of the significant parameters which allow agreement. The significance of the results from the study is demonstrated by comparing the postulated stability and creep response of a solution-mined cavern using the previous understanding of salt behavior and the understanding developed from this study.

Jan 1, 1985

By Thad M. Jones

This paper considers the sampling, digitizing and reconstruction of seismic signals. A sampling frequency range is proposed and a minimum limit is suggested. Digitizing precision criteria for both peak velocity and analysis applications are given. Several methods for reconstructing signals from sampled data are presented.

Jan 1, 1985

As near surface deposits are increasingly mined out and pit widths beginto exceed the reach of practical direct-casting stripping machines, high haulage costs can make truck-shovel pre-stripping operations uneconomic. This is compounded because the rate of inflation for diesel fuel oil, lubricants, tyres, etc. exceeds the general rate of inflation. The use of conveyor transport systems, long established in terracemining operations in weak materials, e.g. engineering soils, can provide a viable haulage alternative in pre-strip operations and in some open pit settings. The paper describes the engineering requirements and basic economics of such systems.

Jan 1, 1985

By Rudolf Voigt

Lignite reserves occur all over the world in different climatic regions. This means, that the impact of the hydrologic regime upon mining activities and, vice versa, of the mining activities upon ground and surface water conditions will be different between any two mines. On the other hand, most economically important lignite deposits can be grouped according to principal depositional and structural features described briefly in the following section. These features do allow a preliminary assessments of the nature of ground water problems which may face the mine. The cost of protection against water which threatens a mine, the environmental impact of the appropriate measures to achieve this end and the restraints of population density which both might exclude the most cost-effective approach will govern the project expenditure for drainage work. Whether or not this expenditure can be borne by the project must be established during the feasi¬bility phases of mine planning. So, the somewhat provoking title of this paper does not mean that its question can be answered once for ever. It should rather serve to bring to the attention of the audience the major features of mine water control.

Jan 1, 1985

By Charles R. Jenkins

Three sedimentation ponds had their performance evaluated before and after installation of modifications. Each pond had a floating baffle installed, two had siphon outlets and one had a floating outlet device. Baffles inhibited short circuiting, and the outlet devices retarded flow following a rainfall event, and drained the pond creating a large storage volume to maximize detention time. Total suspended solids and settleable solids tests were run on samples of influent and effluent to evaluate pond performance. Particle size analyses were run on samples containing measurable amounts of solids. Performance improved in each pond, with baffles providing the major improvement. Through the entire surface mining process un- protected soil is exposed to direct rainfall and subject to accelerated erosion. Without controls, receiving streams would be "choked" by the additional sediment load. Several states, including West Virginia, require that sediment control ponds be constructed to trap the sediment before the water enters receiving streams. Even well designed ponds have exhibited difficulty in meeting effluent limitations. In a study supported by EPA, about half the ponds did not meet effluent limitations (1). There is a critical need to reduce sediment losses using presediment pond controls or by improving sediment pond performance. The objectives of this study were to evaluate modifications designed to improve sediment pond performance by; 1) monitoring three ponds prior to modification, 2) install floating baffles and 3) modify the principle spillway and determine the change in pond performance.

Jan 1, 1985

By Benjamin W. Haynes

The Bureau of Mines conducted research to provide technical information needed to devise waste management plans for the processing of manganese nodules. Studies included summary descriptions of Pacific manganese nodules, process options and flowsheets, methods for characterizing nodules and their tailings, and results of analyses of laboratory and pilot-plant generated tailings. This information is the result of a cooperative research effort of the Bureau of Mines and the National Oceanic and Atmospheric Administration (NOAA), with NOAA providing funding and the Bureau conducting the research. A summary of the extensive literature review is provided for manganese nodule mineralogy, chemistry, processing techniques, and methods of analyses. Characterizations and analyses of laboratory-generated tailings and slags are given, as well as the results of the leaching studies on these waste materials. Leachability was determined by three standard leachate tests- the Environmental Protection Agency (EPA) extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the U.S. Army Corps of Engineers-EPA seawater elutriant test. While the wastes generated in the laboratory may not be entirely representative of those to be generated in full-scale plants, results of these studies provide a positive indication that commercial recovery of cobalt, copper, manganese, and nickel from manganese nodules would be environmentally acceptable.

Jan 1, 1985

By R. A. Matuszak

Historically most mine management teams have been forced to operate in a more or less subjective manner. The objectives of mine management are simple and clear. Like other operational managements, mine management teams have the traditional well defined goals of improving efficiency and production while decreasing costs. Unlike other operational managements however, mining teams deal regularly with a vast assortment of uncertainties caused by: - Key production tools being mobile and widely dispersed, and - Non-uniform mining conditions At best in most operations these conditions cause obstacles to productivity and at the same time cause long delay in managment awareness of the obstacles. Planning with delayed feedback of information about necessary deviations is incomplete planning. For these reasons increased operational efficiency remains a constant though somewhat elusive goal.

Jan 1, 1985

Western Mining Corporation began shaft sinking operations at it&apos;s Foster orebody, south of Kambalda, on the 20th June, 1984. The top levels of the orebody are currently being mined via a decline some 1.5km away.Long term plans require the shaft and decline to combine and produce 400,000 tonnes of nickel ore per annum. Eventually all of the ore produced will be hauled up the shaft.The shaft is 4.5m in diameter and the target depth is 760m. Ground conditions to date suggest there will be no further need for concrete lining beyond the oxidised zone. As such, the sink is an open-shaft development in competent basalt rock. Shaft furniture will be installed on completion of the excavation to the target depth.This paper summarises the experience in the project to date, along with comparisons to conventional shaft sinking methods employed in previous years at Kambalda Nickel Operations.

Jan 1, 1985

By A. Lloyd, Montgomery, J. Jorgesen, W. J.

"Coals are ranked according to their degree of metamorphism or progressive change in the natural series from lignite to anthracite. The reader is referred to ASTM Standard D-388, ""Standard Classification of Coals by Rank"" for a detailed description of the system in use throughout North America including Canada.Fixed carbon and calorific value (expressed in Btu/ lb) calculated to the mineral-matter-free basis have been chosen as the main characteristics from which rank is established. Higher rank coals are classified according to fixed carbon content, lower rank coals according to the calorific value on a ""moist"" mineral-matter-free basis. Certain adjacent groups are differentiated according to their agglomerating (caking) properties. ""Moist"" refers to inherent moisture. Referring to Table 1, coals having calorific values greater than 14,000 Btu/lb on a moist mineral-matter-free basis and fixed carbon of 69% or more on a dry mineral-matter-free basis are classified according to fixed carbon. Coals having calorific values of less than 14,000 Btu/lb on a moist mineralmatter-free basis are classified according to calorific value on a moist mineral-matter-free basis. Agglomerating coals having 69 to 86% fixed carbon on the dry mineral-matter-free basis are classified in the low or medium volatile group of the bituminous class according to their volatile matter content. Agglomerating coals having calorific values between 10,500 and 11,500 Btu/lb are classified in the high volatile C bituminous coal group; nonagglomerating coals in the same calorific value range are classified in the sub-bituminous A coal group."

Jan 1, 1985

By R. M. Campoy

Mexico&apos;s mineral wealth has long been recognised and indeed has played a historically significant role on a world scale. The dynamics of the Mexican mineral industry have experienced a dramatic transformation especially over the last two decades. This transformation has mainly been instigated by the high growth rates and industrialisation of the Mexican economy since the 1960&apos;s. This paper focuses on the base metals sector of the industry which represents one of the major contributors to this transformation. The objective is to present a brief base metals review and to discuss some recent occurrences which pertain to this sector of the industry. This is followed by a discussion of mining&apos;s relevance in the current economic situation in Mexico. With this overview as background, the investment climate, primarily from a domestic investor&apos;s perspective and secondly in terms of foreign investment, is discussed. Finally, some recent government initiatives, including tax and accounting changes, are outlined. Any one of the sections of this paper can easily be developed into an extensive and indepth analysis; however, the intention of this paper is to provide the reader with a broad overview of the topics discussed.

Jan 1, 1985

By James J. Broderick

In the production of Pig Iron - Limestone, Coke and Iron Ore pellets are changed to the blast furnace and reacted at approximately 2,800 degrees F. The resultant products are molten iron and a molten slag - not unlike lava. The molten slag stream is channeled into open pits, cooled with water, crushed and sized for various industrial applications. The production of steel from pig iron in open hearth, B0P, BOF and electric furnaces results in somewhat similar slags: but since free lime is normally the flux, the resultant slags are not satisfactory for use in cement pastes. When exposed to water, the lime slakes, expands by 250% and ruptures the concrete. Thus, the slag discussed first is Blast Furnace Slag composed of 30 to 40% Silica (SiO2) Alumina (AL202) 7 to 16% Lime (CaO) 32 to 45% and Magnesia (MgO) 5 to 15%. The oxides do not exist as free oxides but rather as silicates and alumino silicates which are chemicall inert. Since transportation costs limit the area of use, blast furnace slag can only be found in concrete products produced within 60 to 100 miles of a blast furnace operation. Even within these areas where slag is in heavy supply, quite often the use of slag is minimal for concrete aggregate and the major outlet is road base.

Jan 1, 1985

By J. H. Johnson

The report references reports and publications from 1975 to the present related to diesel underground mine air quality research undertaken by Michigan Technological University. Research results obtained on this contract are summarized in 5 different sections as follows: Section 1 - Development of a Systematic Approach to Monitoring, Data Analysis, and Interpretation for Diesel Mine Air Quality Control, Section 2 - Experimental Evaluation of LHD On-Board Air Quality Control Systems, Section 3 - Development of a Portable Self-Contained LHD Tailpipe Emissions Measurement Apparatus for NO , N0, CO, CO , and Particulate Matter, Section 4 Quantitative Analysis of Diesel and Coal particulate Matter by Laser Raman Spectro¬scopy and Section 5 - Development and Application to Detector Tubes of a Laboratory Method to Assess Accuracy of Occupational Diesel Pollutant Concentration Measurements.

Jan 1, 1985

By C. D. Jardine, D. G. Patton

Rapidly increasing energy costs and more rigid customer quality requirements necessitate improved control of pelletizing processes. With the introduction of dedicated microprocessor-based controllers, sophisticated control strategies are now possible. An application of this technology at Carol Project has resulted in fuel savings, improved pellet quality, and standardization of operating procedures. This was accomplished with no production loss by using a "building block" approach to design and equipment selection.

Jan 1, 1985

By Steven E. Follin

In-situ leaching is commonly used to recover uranium from low-grade deposits in sandstone formations. Acceptable recovery rates can only be obtained if the formation retains its permeability during leaching. Field experiences indicate that microbial growth, stimulated by the leaching pro- cess, can cause plugging problems. To investigate this hypothesis, leach solution and solid samples from well casings and submersible pumps were obtained from four in-situ mining sites. Chemical and microbiological analyses were performed. Bacillus species, Micrococcus species, pseudomonads, and xanthomonads were isolated from these samples. A mixed culture of these organisms was inoculated into a uranium core that was being leached in the laboratory. The permeability of this ore sample decreased to one-third its original value after 16 days. The addition of hydrogen peroxide (0.2 g L-1) to the leach solution killed the microbes and restored the permeability to its original value. This suggests that periodic injection of hydrogen peroxide into production wells may reduce microbial plugging in these wells and the immediate surrounding formation.

Jan 1, 1985