Search Documents

By Frederick F. Frick

SPONGE iron as produced at Anaconda is a fine, -35 mesh, impure product, about 50 pct metallic iron, obtained from the reduction of iron calcine at a temperature of 1850°F by use of coke resulting from slack coal. The metallic iron particles are bulky and spongey and precipitate copper readily and rapidly from a copper sulphate solution. Investigation of the treatment of Greater Butte Project, Kelley, ore at Anaconda early showed the desirability of using sponge iron as a precipitant for the copper in solution resulting from desliming of the ore in a dilute sulphuric acid solution. Anaconda had done considerable work on the production of sponge iron in 1914 for use as a precipitant of copper from leach solutions. Some success and considerable experilence were attained at the time. indicating that, sponge iron might be successfully made by a modification of the process used in 1914, a batch process in which an iron calcine was reduced by means of soft coke, resulting from noncoking coal, in a Bruckner-type revolving horizontal cylindrical furnace widely used 50 years ago. The coke and calcide formed the bed in the Bruckner furnace, which was rotated at about 1 rpm. The bed was brought to a temperature of about 1800°F by means of an oil flame over the surface. Although results were reasonably satisfactory, they did not warrant full development of the process at that time. A good deal of work has been done in the last 50 years on the production of sponge iron. The objective in some cases has been the production of a precipitant for copper from solution, but the bulk of the work has been done for the production of open-hearth steel furnace stock. The production of an open-hearth stock presents two problems rather than one: first, producticon of the sponge iron, and second, what is perhaps of equal difficulty and importance, conversion of the sponge iron into a form suitable for use in the open-hearth furnace. So far as is known to the writer, none of the sponge iron processes tried in the past have proved to be economically feasible. However, Anaconda had a combination of conditions appearing to justify an attempt to produce sponge iron which would serve for the leach-precipitation-float process. It was thought that the process used in 1914, if changed to a continuous one, might work out satisfactorily. The following favorable conditions at Anaconda justified the investigation: 1—A sufficient tonnage of good grade iron calcine resulting from the roasting of a pyrite concentrate in one of the acid plants, at substantially no cost. 2—Reasonably cheap natural gas. 3-—The fact that there was no need for production of a high grade product. 4— The fact that there was no need for obtaining a consistently high reduction of' the iron in calcine. A small revolving Bruckner-type furnace about 2 ft ID by 4 ft long was set up for early pilot work at the research building. This pilot furnace showed that a satisfactory product could be obtained at reasonable cost. It also indicated a marked advantage in preceding the reduction furnace with a furnace of similar size and capacity for preheating and roasting out any residual sulphur from the feed. The small furnace was operated for several months, various details of the process were worked out. and sponge iron was produced to supply a pilot LPF plant which treated 300 lb of Kelley ore pel- hr. Later a second pilot furnace 5 ft in diam and 12 ft long inside was set up at our reverberatory furnace building. This furnace confirmed the data of the small furnace and gave a basis for design of the final plant. At Anaconda a pyrite concentrate, running about 48 pct S, is recovered from copper concentrator tailings by flotation. This concentrate is roasted to sulphur of 3 pct or less at the Chamber acid plant. The iron calcine contains about 57 pct Fe and 18 pct insoluble. The iron calcine feed, as mentioned before, is re-roasted and preheated in a reroast furnace preceding the reduction furnace. Both are of the Bruckner type. The reroasted calcine is fed into the reduction furnace at 800" to 1000°F along with 30 pct slack coal. In the feed end of the furnace the volatile is burned from the slack, giving a soft coke which readily serves for reduction of the iron. Hard metallurgical coke will not serve the purpose. since it does not reduce CO readily at a temperature of 1850°F. All indications are that the actual reduction of the iron is accomplished by carbon monoxide below the surface of the bed, which is 30 in. deep at its center. Apparently there is a constant interchange: Fe²O³ + 3CO = 2Fe - 3CO², CO² + C = 2CO Actually iron oxide is reduced by CO at somewhat lower temperature than the 1850 °F used in the process. but this temperature is necessary to obtain a satisfactory rate of furnace production. The furnace atmosphere is generally reducing, and typical blue carbon monoxide flames satisfactorily cover the bed. Gas flames from four 3-in. Denver Fire Clay Inspirator burners are played directly on the bed, which is slowly cascaded by the 1 rpm of the furnace. An excess of coke is necessary to assure maintenance of good reducing conditions in the furnace bed. Part of this coke is recovered for re-use.

Jan 1, 1954

By Herbert Cremer

The United States,-the largest nickel consumer in the world, produces virtually no nickel from domestic ores. Dependence upon outside nickel - sources and increasing strategic, importance of nickel focused the attention of the United States on deposits within its boundries. The most likely domestic sources of nickel are low-grade oxide and silicate deposits, such as the Cle Clum deposit, Kittitas County, Wash., and the Riddle deposit, Douglas County, Oreg. The Federal Bureau of Mines, Northwest Electrodevelopment Laboratory, Albany, Oreg. has been investigating electric smelting of low-grade oxide and silicate nickel ores. These smelting studies have been on selective reduction to produce low-carbon ferronickel. Selective reduction is based upon the relative reducibility of: nickel, iron, and chromium, in the order named, when the charge contains insufficient carbon or other reductants to reduce the entire quantity of these metals present in the ore.

Jan 1, 1954

By John D. Price

R. W. Campbell (Jones and Laughlin Steel Carp., Pittsburgh)—As usual John Price has presented an excellent paper. I know of no one who has devoted more time and conscientious thought to this subject than he has, and his efforts have produced scientific data and conclusions of real value. Results of similar studies made by the Jones and Laughlin Steel Corp. on the blending of Pennsylvania coals may be of interest. During 1935 the late F. W. Wagner and the present writer developed an empirical physical fuel value formula for evaluating the combined physical tests of metallurgical coke, see Table IV. In the development of the formula, the tumbler test, shatter test, screen test, and porosity of coke have been taken into consideration. Each of these tests brings out some physical property not expressed by the others, and in estimation of the importance of these tests as a medium for evaluating coke for the blast furnace, their worth has been graded as follows: It was thought that some additional penalty should be applied to cokes that do not show a uniform screen size, assuming that coke larger than 4 in. was not desirable and that this size was an indication of irregular size. Therefore the screen test factor is further corrected by applying a penalty of 1 pct for each 1 pct material greater than 4-in. size as shown by the screen test. The physical fitness of coke for blast furnace use depends upon four fundamental characteristics: l—gen-era1 strength, as indicated by the shatter test; 2— abradability, or the resistance of cell walls to reduction in size by attrition, as indicated by the tumbler test; 3—porosity; and 4—size and uniformity. Each of these characteristics is not of equal importance, but surely, in an attempt to determine an accurate physical value, the individual value of each should be taken into consideration. The formula is used as a yardstick, so to speak, in determining variations in the normal production of metallurgical coke and in making comparisons between normal coke and experimental blends with other coals. Table IV gives results of coking tests on raw and washed high volatile coals and these same coals with blends of coke breeze, anthracite coal, char and low volatile coals, all from Pennsylvania. The table also gives the source of the coals and coke breeze, as well as their proximate analyses. It will be noted that the washing of the raw high volatile coal increased the physical fuel value from 26.17 to 39.16, showing the effect of removing shale and slate which produces a detrimental fracturing and weakening of the coke. It is a well known fact that many Pennsylvania high volatile coals contain an excess of resinous material or binder which has a tendency to weaken the coke, owing to its high evolution of gases during carbonization. Tests were therefore made with coke breeze, an inert material, in an attempt to alleviate this condition. Blends of washed coal with 5 pct and 7.5 pct coke breeze collected from the coke plant quenching sump (82.9 pct through 1/8-in. screen) resulted in cokes with a physical fuel value of 20.75 and 16.73 respectively, lower than results obtained from 100 pct raw high volatile coal. It will be noted that the percentage of + 4-in. coke increased but that the tumbler test was very low. Undoubtedly better results could have been obtained if the coke breeze could have been crushed extremely fine. During World War II the government asked the coking industry to consider the use of anthracite coal as a substitute for high quality low volatile coal, which was extremely scarce at the time. The next series of tests was made with blends of raw and washed high volatile coals and 5, 10, and 15 pct Pennsylvania No. 5 buckwheat anthracite (100 pct through l/8-in. screen). It was necessary to use some raw high volatile coal in these blends because of insufficient washer capacity at the time. It will be noted that the physical fuel values

Jan 1, 1954

By D. F. Gibbons

THIS investigation was undertaken in order to gain further information on the mechanism of plastic deformation of iron at temperatures between room temperature and 77.2°K, and also to contribute to our understanding of the low temperature brittleness phenomenon that occurs in both the tensile and impact tests. It was decided to study as pure an iron as possible and to use the tensile test in order to simplify the problem as much as possible. Two series of iron were used throughout the investigation: iron A, obtained from the National Research Corp. and supplied as gas-free, high purity iron; and iron B, obtained from Fast' and produced by melting iron under purified hydrogen. Typical analyses of samples of both irons, after fabrication, are given in Table I. The main difference in composition of these irons is in their nickel and oxygen contents. Nickel has a very large solid solubility in iron. However, oxygen has an extremely small solid solubility. An attempt was made to reduce the oxygen content still further by remelting under purified hydrogen. This was successful in reducing the oxygen content to -0.0006 pct. However, no results on tests of this iron are included, since difficulty was encountered in fabricating the ingot. Wire specimens 1 mm in diameter were used for the investigation. The wires were produced from the ingots, as supplied, by cold rolling and swaging, with intermediate vacuum anneals at 700°C. Care was taken to reduce preferred orientation in the wires to a minimum by keeping the percentage of reduction in area between anneals of 30 to 40 pct. X-ray transmission photographs showed no indication of preferred orientation. The final grain size of iron A was 20 to 24 grains per linear mm and of iron B, 16 to 18 grains per linear mm. All specimens were tested in the decarburized and denitrided condition unless otherwise stated. The procedure was to pass hydrogen, saturated with water vapor at 26oC, over the specimens at 730°C for 2 hr. The specimens were quenched in iced water and then annealed in a vacuum of - 5x10-6 mm Hg for one day at 560°C to remove hydrogen. Higher temperatures were used for the vacuum anneal but this temperature was found to be quite satisfactory in removing hydrogen. The specimens were slow-cooled after the vacuum anneal. Where it is stated that the specimens were carburized, the specimens were given an identical decarburizing treatment and then carburized by passing hydrogen, saturated with pure n-heptane vapor at 0°C, over the specimens at 730°C. The specimens were then homogenized at 730°C for 2 hr in dry hydrogen. After the carburizing treatment the specimens were given the same vacuum anneal as for the decarburized specimens. The carbon content was determined from the maximum value of the internal friction carbon peak.2 Apparatus Fig. 1 shows a diagram of the tensile apparatus, with half the cooling coil removed. The cooling coil enabled temperatures from 200" to 77.2oK to be obtained. The apparatus was designed to fit a standard Tinius Olsen Universal tensile machine. The apparatus consisted of the rigid plate A which carried two carefully machined hooks H. These hooks attached the plate firmly to the moving crosshead of the tensile machine. The lower grip B was rigidly suspended from the plate A by three stainless steel rods. The upper grip C was joined to the upper grip of the tensile machine by the stainless steel rod E. The lower part of the apparatus was surrounded by a Dewar vessel, which was made a sliding fit inside the brass collar D. The specimen was held in a clamp which fitted into the grip, forming a ball and socket joint (see inset a). This was to attain as nearly pure

Jan 1, 1954

By Harold J. Rose

It is a real pleasure to attend another meeting of the Institute. This is partly because I am a Westerner by birth and training. As a young man I had personal experience with firing Colorado and Wyoming coals. The coal industry of the United States has done an outstanding job of producing coal. We can all be proud of the industry's record of continuously adopting technical improvements in coal mining. NEED FOR MORE EFFECTIVE COAL MARKETING However, it cannot be said that the industry has done an equally good job of marketing coal. There has been a rapid growth in U. S. population, and an even greater expansion of industrial demands for heat and power. Yet coal consumption for the past several years has been no greater than it was 40 years ago, in 1912 and 1913.

Jan 1, 1954

By H. L. Gilbert

Zircon sand may be reacted with sodium hydroxide at 600° C. to form sodium zirconate and sodium silicate. Sodium zirconate is water insoluble and so may be washed free of sodium silicate. The sodium zirconate may then be converted to zirconyl chloride by the action of hydrochloric acid and the zirconyl chloride crystals separated by cooling the solution. This approach produces zirconyl chloride of satisfactory purity with less cost than is involved in buying anhydrous zirconium chloride and converting it. A proposed design for a plant is given, INTRODUCTION This work was conducted by the Rare Metals Branch as a part of research on zirconium at the Bureau of Mines Northwest Electrodevelopment Laboratories, Albany, Oreg., under the guidance of S. M. Shelton, Regional Director. The work was supervised by W. W. Stephens, head of the Rare Metals Branch (now with Carborundum Metals Corp.).

Jan 1, 1954

By W. H. Mathews

"The Hardie group of cinnabar claims is in the interior of British Columbia; 25 miles northwest of the city of Kamloops. It is one of a number of mercury; properties scattered along a north trending belt 20 miles long and up to 5; miles wide. In all but one of these properties cinnabar is associated with; dolomite veinlets in zones of carbonate alteration in bedded rocks of Triassic; and Cretaceous (?) age; or in intrusives cutting these bedded rocks. No dolomite alteration or cinnabar mineralization is known in the undoubted Tertiary rocks adjacent to the mercury belt.The mercury showings of the Hardie group lie for the most part in a granitic stock cutting Cretaceous (?) volcanics. The rock in this intrusive shows marked variations in texture and has been described in earlier reports as granite and granodiorice, granite porphyry, and trachyte or dacite porphyry. At Hardie mountain the cinnabar mineralization, unlike that of the other properties, is associated with a fine-grained, almost chalcedoni c, quartz; carbonates, though present, are of minor importance. Some of the most interesting showings are found in an adit in the southeastern part of the property where cinnabar mineralization shows a very distinct structural but not a genetic relationship to a brown porphyry dyke 2 to 8 feet wide cutting a phase of the stock that may best be described as aplitic"

Jan 1, 1954

By M. S. Hunter, D. L. Robinson

An extremely fine subgrain structure found in aluminum and aluminum alloys is shown and a method for revealing this structure is described. The appearance and some of the characteristics of this structure are described and the possible significance of subgrain structure in terms of chemical, electrochemical, and metallurgical processes is considered. GRAINS and grain boundaries, which constitute the principal manifestations of the crystalline aggregates known as metals, play such an important part in determining the characteristics and properties of metals and alloys that their nature and behavior have long been of much concern to the met-allographer. Many investigators have speculated on the possible existence of a finer structure within the usual grain structure and, through X-ray diffraction and metallographic techniques, have revealed evidence that such finer structures exist. Among these structures are the mosaic blocks and domains described by Burgers1 and others in their contributions on crystalline structure and the dislocation theory, the small units associated with polygoniza-tion described by Cahn,2 and the intragranular blocks revealed more recently by Lacombe and Beaujard.3 his paper describes some novel methods for clearly revealing a very fine granular substructure within the usual grains of pure aluminum and aluminum alloys. It also compares the characteristics and behavior of this subgrain structure with those of the ordinary grain structure and gives some examples of the manner in which this substructure may influence the characteristics of aluminum alloys. Metallographic investigations of aluminum and its alloys have dealt extensively with the functions and behavior of grains and grain boundaries and have evolved a definite concept of the relation between grain structure, orientation and physical, mechanical, chemical, and electrochemical behavior. During the examination of etched samples, a roughening or mottling of the body of certain grains has occasionally been observed. Such roughening obviously represented differential attack by the etching solution, but its true significance was not at first realized. It is now known that this roughening probably rep- resented a subgrain structure, although the particular etching treatments used were not capable of revealing this subgrain structure clearly. Also, in practically all cases, the subgrains were apparently far too small to be resolved by the light microscope. Recently, a method has been developed for revealing clearly the subgrain structure of most aluminum alloys. This method is somewhat unique in that it eliminates much of the usual tedious mechanical polishing and the attendant danger of a surface layer of flowed metal and at the same time is simple, rapid, and effective. It involves the use of the Alcoa R5 Bright Dip, a patented chemical polishing treatment licensed by Aluminum Co. of America. This treatment produces a bright, highly polished surface at least the equal of any mechanical polish and also etches the subgrain boundaries as well as the ordinary grain boundaries to reveal both the grain and subgrain structure simultaneously. Metallographic specimens to be examined are taken through the customary grinding and polishing operations used for aluminum alloys.' The usual care required in the final polishing operation to prevent a flowed surface layer and to obtain a high polish is not necessary, however, because any flowed layer is eliminated and a high polish is produced by the final immersion in the Alcoa R5 Bright Dip. Depending on alloy type, this dip takes from a few seconds to about 3 min, after which the sample is rinsed well, blown dry, and is ready for examination. The substructure can be revealed by some of the usual metallographic methods such as electropolish-ing or mechanical polishing and etching but no method has been found which is the equal of the new chemical polishing treatment. Mechanical polishing followed by the usual metallographic etching is not entirely satisfactory for revealing this substructure, probably because of the flowed surface layer resulting from the mechanical polish. If the usual etching methods are prolonged sufficiently to remove this layer, the specimen surface becomes quite rough and the substructure is not defined clearly.

Jan 1, 1954

By P. A. Albert

THE to a transformation has been investigated by Newkirk1 in sponge titanium alloys which had been relatively slow-cooled so that several grains formed in a former grain. For a nucleated from , Newkirk assumed the following relationships and found them consistent with his experimental results: (00.1)a (110)Pll.01. II [111] Liu and Margolin,' in their investigation, found that the habit planes of martensitic in titanium consisted of planes of the families (3341, and (3441,. Using Newkirk's orientation relationship, the (3341 habit plane is found to correspond to the (1450) plane of a.

Jan 1, 1954

By R. M. Creamer

Attempts have been made to electroplate titanium and zirconium from aqueous, nonaqueous, and fused-salt electrolytes. Metals were produced only in fused-salt electrolytes, the major product being sponge metal. All other electrolytes gave only partial reduction of the metal ions. Fused alkali borate electrolytes containing titanium salts gave titanium boride powders and coatings of poor adherence. Some of the problems encountered in the deposition of these metals and some of the aspects of titanium and zirconium chemistry involved are discussed. INTRODUCTION Titanium and zirconium are both relatively light, noncorrosive metals with both military and civilian uses. This has led to intensive investigations into the metallurgy of these metals. Both metals are high in the Electrochemical Displacement Series and are difficult to prepare in a pure state. At present they are prepared by reducing their chlorides, using magnesium. Electrolytic reductions have resulted in the preparation of fine powders or sponge of variable quality. It is believed that a good process of electroplating these metals on a baser metal would result in a very desirable product. The objective of the research summarized in this report was to investigate methods of electrodepositing these metals, with the idea of producing uniform, coherent plates. Most of the work was concentrated on titanium, the more abundant of the two metals. A system developed for titanium should be applicable to zirconium owing to their chemical similarity. Information gained from these experiments may also be applicable to the electro-winning of the metal.

Jan 1, 1954

By M. R. KEYS

"The property is about 120 miles north of Red Lake in the Favourable Lake area, district of Kenora ( Patricia part) , Ontario. The original discovery was staked by K. Murray in December, 1927. The first development work was done by the Favourable Lake Mining and Exploration Company. In 1936 Newmont Mining Corporation acquired control of the property and developed it to production by September, 1939. Production to the end of 1945 had a value of $7,534,656 from 441,457 tons of ore, an average value of $17.04 a ton . This production was mainly from gold and silver, with lead and zinc of subordinate importance.The rocks in the vicinity of the mine trend in a north-south direction. From east to west the sequence is: (1) A dark-coloured, massive rock, presumably a flow, composed mainly of quartz and biotite. ( 2) A buff- coloured, scricitized rock locally containing quartz phenocrysts and black hornblende. This is an alteration product of the dark variety and is later than the folding. It occurs mainly within the dark rock. (3) A series of sediments comprising thin beds of greywacke, grit, quartzite, conglomerate, and iron formation. ( 4) A gabbro sill, now largely altered to amphibolite.With the exception of the buff type, these rocks dip 80°E. The buff rock has a very irregular outline in comparison with the other rocks and appears to dip somewhat more flatly east. Felsite and diorite dykes are also present. These have a general strike of S.60°E. and dip 65°S .W. A post-ore diorite dyke trending N.15°E. occurs about 2,000 feet east of the mine area."

Jan 1, 1954

By Merlyn B. Buhle

The value of the earth resistivity method in groundwater studies in Illinois has long been recognized. Owing to the sharp electrical contrasts between sand and gravel deposits and glacial till, alluvial silt or underlying shale, much of the earth resistivity prospecting has been of a relatively elementary nature and has been highly successful. Approximately 90 pct of earth resistivity interpretations by the State Geological Survey have been accurate for practical purposes. Four studies involving fairly simple geologic situations are presented in this paper as typical cases. FOR the past 20 years electrical earth resistivity exploration has been used in Illinois in many phases of study undertaken by the State Geological Survey, chiefly in locating and outlining deposits of water-bearing sand and gravel from which to obtain ground water for municipal and industrial supplies. At least 43 municipalities in the state derive their total water supply from deposits of sand and gravel discovered by resistivity methods. These deposits occur in both Quaternary and preglacial valleys and within much of the glacial drift which covers a large portion of the state. In recent years there has been much demand from rapidly growing municipalities for help from the Illinois Geological Survey to extend existing well fields. Water supplies for many and varied industries constitute a considerable portion of the Survey's studies. The diminishing need of water supplies for railroads has 'been accompanied by an increasing demand by the oil industry for water for secondary recovery programs. The instruments used by the Illinois Geological Survey follow closely the commutated direct current circuits developed by O. H. Gish and W. J. Rooney' using the Wenner2 electrode configuration. More recently replacement of the hand-driven commutator by a synchronous vibrator has led to increased ease of operation and accuracy. Continuing improvement of equipment and technique has led to many changes in the instruments, but the operating theory remains the same. In the field operation at a selected station, four electrodes are set at equal distances in the ground 6 to 10 in. deep, in a straight line. A 16 to 20-cycle current is applied to the two outside steel electrodes

Jan 1, 1954

By D. D. Blue

To insure domestic production of aluminium for, essential civilian and defense uses, the Government, under authority of the Defense Production Act of 1950, programed and promoted an aluminum-expansion program that will more than double the primary production capacity that existed in 1949. In view of this vastly increased production, the raw materials, with respect to both quantity and sources, are reviewed. The raw-material consumption pattern, the requirements during an expansion period when excess quantities of materials for starting up new facilities are consumed, and the probable requirements for production of 1.7 million tons per year of primary aluminum are discussed. The raw materials that presented the most difficult supply problems were bauxite, electrical power, and fluoride salts, and the supply pattern for these materials probably will undergo changes. A major part of the electrical energy for the increased capacity was to come from thermal generation, Jamaica-was to become a major source of bauxite, and synthetic fluoride salts were replacing natural cryolite in increasing quantities. Other raw-material requirements discussed are: Soda ash; lime, and limestone; starch; filter cloth; fuel; alumina; the carbonaceous materials, green and calcined petroleum coke, high-and low-temperature pitch and coke or anthracite; cryolite; aluminum fluoride; the materials going into production of synthetic fluorides, acid-grade fluorspar, and sulfuric acid; and labor. INTRODUCTION The raw materials for the aluminum industry that have received the most publicity are bauxite, the ore that supplies elemental aluminum, and electrical energy, the means by which aluminum oxide is reduced to metal. A number of other important materials are, however, required in large quantities in the production of primary aluminum metal.

Jan 1, 1954

By J. D. Sargent

Selenium might be described as a paradoxical element, being a metal or a nonmetal, a conductor or nonconductor, amorphous or crystalline, colorant or decolorant, and a hydrogenator or dehydrogenator. Selenium was discovered in 1817 by the Swedish chemist, Berzelius, while studying flue dust from the lead chambers of the sulfuric acid works at Gripsholm, Sweden.

Jan 1, 1954

By Rudolph G. Wuerker

The progress made in testing the strength of rocks and minerals as they are encountered in mine operation is reviewed. An attempt is made to correlate these physical measurements with abrasive hardness, grindability, and behavior in comminution on one hand and fracture of rocks in pillars and roof control on the other. THIS paper reviews the progress made in testing the strength of rocks, ores, coal, salts, and other minerals as they are encountered in mine operations. It attempts to correlate the results of these physical measurements with technological properties more useful to the mining engineer: abrasive hardness, grindability, and behavior in comminution on one hand, and roof control, fracture of rocks in pillars, and mining methods with controlled caving on the other. In the following pages, the materials discussed will be referred to as rocks. Basic to rock mechanics and comminution are the problems of strength, elastic behavior, and failure, common to all brittle materials. A distinction will be drawn as to theoretical and applied research, and discussion of the progress made in each field will include test data obtained by the U.S. Bureau of Standards,1-1 the U.S. Bureau of Mines," the Iowa Engineering Experiment Station,"." the Committee on Geophysical Research at Harvard University,'" Basic Industries Research of the Allis-Chalmers Manufacturing Co.,11,12 by Philipps,13 and by Mueller," to name only a few. With refinements of testing methods and increased standardization. more useful and more comparable results have been achieved. This is especially important in testing a material like rock, as the inherent heterogeneity demands careful and exacting procedures. New measuring procedures that appear to supersede well known standard methods have contributed to faster and less costly testing yet have introduced new concepts, with implications as to comparability of results which must be watched. Reference is made to the sonic method for determining elastic properties," to be discussed in detail below. Basic Investigations Historically, all work in the field has started with the simplest determinations such as those for crushing strength, abrasive hardness, and grindability. These serve the limited objectives in the researcher's field of specialization: building construction, road ballast, roof control in mines, comminution, and seismic prospecting. Occasionally, fundamental properties like the modulus of elasticity E and Poisson's ratio v have been determined with the idea that they might have some bearing on the technological properties of the material under investigation. But it was not until the work of Philipps,13 of Harvard University,'" and of the U.S. Bureau of Mines"' that sufficient basic data were collected to allow researchers to go beyond the technological test and find the fundamental laws behind the behavior of rocks in mine and mill operations. The properties to be looked for are those that describe the elastic behavior of any material, the modulus of elasticity E and Poisson's ratio v being the ones determinable with least difficulties. Only two such properties are required to compute any other property such as the shear modulus, the modulus of rigidity, and the bulk modulus, all of which are related to each other according to well known equations of the theory of elasticity." In spite of their heterogeneous character, all rocks tested have possessed elastic properties. This does not mean that rocks of the same type always have the same modulus of elasticity, which varies exactly as the crushing strength or any other physical property of a rock can spread over a wide range. This has been explained by imperfections of the material always found in rocks, but to some extent this scattering of data is caused by inaccuracies inherent in the testing methods. Modulus of Resilience, a Criterion of Failure Increased availability of E values should allow us to test the validity of the quantity of strain energy theory which has been used in the solution of roof control problems by Philipps13 and by Holland.'" Recently Bond and Wang12 have applied this theory to explain the failure of an elastic material in comminution. Actually it is a very old theory, proposed as far back as 1885 by Beltrami.16 By its assumption the condition of yielding is determined by the term S2 M, = — x volume. Here M, is the modulus of 2E resilience, and its dimension is inch-pounds per cubic inch, that is, work per unit volume. Its numerical value is equal to the area under the stress-strain diagram. In the foregoing equation S is the yield stress (in psi) in tension or compression, whatever the case may be. E, the modulus of elasticity, is in psi. The great appeal of Beltrami's concept of stored energy lies in the fact that the two properties which seem to influence failure most, strength and elasticity, occur in the formula for the modulus of resilience. As an illustration of this, the moduli of resilience in compression of some typical materials tested by the U.S. Bureau of Mines" have been plotted in Fig. 1. The sample of concrete of conventional mix is shown only for the sake of comparison. Its determination was made in the Department of Mining and Metallurgical Engineering, University of Illinois. The values of the moduli of resilience of the various specimens in the plot are:

Jan 1, 1954

By H. W. Maynor, C. J. McHargue

DURING the course of an investigation of materials suitable for use as thermocouples at elevated temperatures by one of the authors, several nlolybdenum-rhenium alloys were prepared. Micrographs of an annealed alloy containing 25 pct Re (intended concentration; analysis not obtained) showed a number of twins, Fig. 1, suggesting a face-centered cubic structure. This note reports the structure and recrystallized wire texture of an alloy containing 25 wt pct Re. Alloys were prepared from 99.9 pct Mo (Fansteel Metallurgical Corp.) and rhenium obtained from the University of Tennessee (purity unreported). Powders were combined and briquetted at 56,000 psi and sintering was carried out at 2400°C for 5 hr in vacuum. Ingots so prepared were swaged at 982.2" to 1037.8oC into wires 0.036 in. diameter, a reduction in diameter of 85.6 pct. These wires were vacuum-annealed 1 hr at 2000°C. A North American Philips 114.59 mm powder camera and nickel-filtered copper radiation were used for structure determination. For the texture determination a Laue-type camera was used with zirconium-filtered molybdenum radiation and, because of the high background, aluminum foil was mounted next to the film. Exposures were taken with the wire perpendicular to the X-ray beam and tilted by 10". It was found that the X-ray pattern could be indexed on the basis of a face-centered cubic structure. Because of difficulties associated with obtaining a good X-ray pattern for this material, accurate parameter determinations were not made. An indicated parameter value of 3.70A was obtained. The X-ray data are given in Table I. The annealed wire texture was observed to be a sharp [111] texture. The spread about this fiber axis was k8" at the surface of the 0.036 in. wire. The annealed wire textures of aluminum have been reported as retention of the [Ill] deformation texture for anneals below 500°C and a new [1121 texture for anneals above 600°C.1 In copper wires, with a [Ill] plus [loo] deformation texture, results indicate a retention of this texture for annealing at lower temperatures and new components or the disappearance of components for annealing at higher temperatures.' The presence of the strong [I111 texture in the molybdenum-rhenium alloy after a 2000 °C anneal suggests that the deformation texture was the same. Acknowledgment The wires used in this study were prepared and heat-treated at the Institute for Atomic Research, and Ames Laboratory, Iowa State College, and the authors wish to express their thanks to the Institute for allowing the use of the material and permission to publish the results.

Jan 1, 1954

By J. W. Spretnak, R. Speiser

IT has been suggested that boron in steel may form a film entirely around the austenite grain and that this film is responsible for the boron hardenability effect. In this connection, it is of interest to examine some of the ramifications of the concentration range of boron usually employed in hardenable steels, namely 0.0005 to 0.003 pct in a grain size range of ASTM grain size No. 1 through No. 10. The ratio of the iron to boron atoms and the number of unit cells of y iron per boron atom are listed in Table I. Even at the highest concentration considered, there are 1600 unit cells of y iron per boron atom, assuming a uniform distribution of boron. To investigate the possibility of the boron film formation, the number of boron atoms required to cover the grain surface completely must be calculated. With some transition elements, boron crystallizes in sheets composed of equilateral hexagons very much like graphite.' The selected value for the length of a side is 1.80Å. A simple calculation shows that two boron atoms cover an area of 8.4x l0 -16 sq cm. Table II lists the number of atoms of boron required for the formation of the monatomic film and Table III lists the number of boron atoms per grain. The hypothetical cases of 100 pct and 10 pct adsorption are calculated (all boron atoms in a grain and 10 pct of all boron atoms in a grain are located at the grain surface respectively). In Table 111, all combinations of grain size and composition below and to the left of the solid line (100 pct adsorption) and the dashed line (10 pct adsorption) are excluded as to the possibility of covering the grain surface with a continuous boron film. Thus, even for 100 pct adsorption, the smaller grains can form the film only at the higher concentrations. For the best case, grain size No. 1 and 0.0030 pct B, the required degree of adsorption is 3.9 pct. The above calculations deal only with the number of boron atoms required to form a monatomic film and do not take into account the mechanism of concentration of boron at the grain surface and the possible limitations to the extent of this concentration at a constant temperature, as for example in the austenitizing process. The question next arises as to how this surface concentration can occur during an isothermal treatment. Such surface enrichment of boron must occur through the phenomenon of surface adsorption, i.e., the concentration of solute atoms in solid solution in the vicinity of the surface without precipitation. A solute atom will tend to concentrate at the grain boundary if it reduces the interfacial tension. The possibility of adsorption effects involving both boron and carbon in iron has been discussed.' In general, the tendency for a sol-

Jan 1, 1954

Jan 1, 1954

By E. J. Gleim

The construction of explosion-proof electric mine equipment for operation in gassy coal mines of the United States was begun as early as 1903. In 1.906, similar equipment with special protective devices was built for export. An investigation of explosion-proof motors was conducted by the United States Bureau of Mines during 1910 and 1911. In other words, this was among the first efforts of the Bureau directed toward the saving of life and property subsequent to its establishment by act of Congress in 1910. In these early motors, those with special devices for relief of explosion pressures predominated. At that time it was generally considered that, by providing for pressure relief, the enclosures could be made lighter in weight because of the lower explosion pressures developed within.

Jan 1, 1954

By W. P. Corking

"The purpose of this paper is to describe the relationship of the goldbearing ore to structure at the Pickle Crow mfoe. Information beyond this scope may be found in the reports and papers of Hurst( l), Bothwell(2), Thomson(3) , and Monette( 4).The property lies on Crow river, in Patricia district, 80 miles northeast of Allanwater, and about 125 miles northeast of Sioux Lookout on the Canadian National railway. From April of 1935, when the mill began operation, to the end of 1944, a total of 564,890 oz. gold and 49,275 oz. silver were recovered from 958,416 tons of ore.Mining on the property is at present carried on in two separate orebodies, the Howell and the No. 2 vein. Stoping has been carried on from every level on the Howell vein to a depth ot 2,450 feet below the surface and from several levels on the No. 2 vein through a mile long cross-cut on the 750-foot level to the Howell vein workings. A steadily increasing volume of ore is being obtained from the No. 2 vein.Each of the two orebodies consists of vein quartz with small amounts of other gangue minerals either in a single vein or a stockwork of veins. Both lie within sheared walls and carry gold in the free state. Fig. 1 shows the position of the veins with respect to the surrounding rocks. It will be noted that the delineation of the beds of iron formation shows that the lava flows and minor, interbedded sediments that make up most of the country rocks are areally folded and contorted.STRUCTURENearly all gold found to date in sufficient quantity and concentration to make ore in the Pickle Crow area is confined to these major quartz veins . Both strike a little north of east and dip north, and in both cases the attitude of the enclosing rocks is somewhat more north of east in strike and more steeply north in dip than that of the veins. As a result of this disposition both veins migrate across their enclosing rocks at a moderate angle in both dip and strike. (In this connection it should be noted that No. 2 vein dips at a considerably flatter angle than its host rock, but has a very pronounced rake to the northeast, effecting the same result as in the Howell vein.)"

Jan 1, 1954