Search Documents

By Thomas P. Battle

Modern-day direct reduction of iron first developed as a small-scale, low capital and operating cost alternative to the blast furnace. Since commercialization of continuous DR technology in the late 1960s, the market for the products of direct reduction has grown to more than 74 million tonnes in 2012. The initial advantages of DR plants over BF facilities have grown over the years, for several reasons, including the increased size of DR modules, lower energy and emissions (particularly CO2), along with the flexibility to use a number of different reductants. The development of DR technology over the past forty years will be emphasized in this presentation, including recent developments that allow for even more direct sustainability comparisons with the iron blast furnace – and even combine the two technologies for improved synergies. Also briefly discussed will be the possibilities of using direct reduction for non-ferrous ores.

Jan 1, 2014

By P. C. Good

This Bureau of Mines report describes the preparation of phosphoric acid directly from phosphate ore, without prior beneficiation, in a small-scale, continuous process research unit, as part of an effort to improve minerals and metals recovery from domestic resources while minimizing environmental effects. Three phosphate-matrix samples, ranging in grade from 18.2 pct P20S5to 11.9 pct P205, were dry-fed at a rate of 1.82 kg/hr (4 lb/hr) to a continuous-circuit, 12-liter, single-tank digester to yield phosphoric acid and byproduct gypsum filter cake. Comparison with earlier data shows that a significantly improved filtration rate was attained in a single-tank reactor compared with that attained in a five-tank reactor train processing the same ore. Iron and aluminum impurities in the product phosphoric acid averaged about 60 pct higher than amounts reported in commercially prepared, concentrate-derived acid. All gypsum filter cakes prepared had a firm, sandy texture, rendering them physically suitable for stacking or landfill use. Introduction of dry attritioning and air classification approximately doubled the attainable filtration rate when the dry-beneficiated product was digested. In air classification, there was a 12-to 14-pct P205 loss. Depending on the technique used and the matrix grade, overall P205 recovery ranged from about 72 to 89 pct.

Jan 1, 1979

By Ilona Johnson

United States metals and non-metallic minerals manufacturing consume about 5,000 trillion Btu annually. Various studies estimate that as much as 20 to 50 percent of this energy is lost as excess or waste heat. Recovery of waste heat can conserve energy, reduce operating costs, and lower environmental emissions. It would be valuable to quantify recoverable waste heat sources and identify the barriers that hinder its recovery. This paper provides an overview of waste heat losses specific to high temperature processes in primary metals and minerals manufacturing. It summarizes findings from a broader study conducted for the Department of Energy Industrial Technologies Program; the study evaluates energy losses, recovery practices and opportunities, and R & D needs for waste heat technology development.

Jan 1, 2008

By J. D. Clucas, N. Verbaan, T. Grammatikopoulos, D. B. Dreisinger, C. Forstner, M. Aghamirian

"Search Minerals is currently exploring the Port Hope Simpson (PHS) Rare Earth Element District in southeastern Labrador, Canada. The Foxtrot Rare Earth Element (REE) Project in the PHS District has a 43-101 resource estimate consisting of 3,410,000 tonnes of Indicated Mineral Resources and 5,850,000 tonnes of Inferred Mineral Resources. The indicated and inferred resources contain 1.07% and 0.98% total rare earth element oxide (including yttrium), respectively. The dysprosium and neodymium grades are particularly attractive at 218 ppm Dy2O3 and 1687 ppm Nd2O3 for the indicated resources and 208 ppm Dy2O3 and 1494 ppm Nd2O3 for the inferred resources. The mineralization remains open along strike and at depth and is only one of a number of attractive exploration targets in the Port Hope Simpson area. The REE minerals fergusonite and allanite are present. The ore can be beneficiated by gravity, magnetic separation and flotation to a recovery of +80% for the individual REE. Acid bake and water leaching may be used to extract REE into solution for subsequent purification and recovery. The extraction range for single stage leach tests were 91-96% for Nd, 84-87% for Tm and 92-94 % for Dy with modest acid consumptions. INTRODUCTIONSearch Minerals Inc. (Search) is exploring the 100% owned Port Hope - Simpson District in Labrador, Canada for rare earth elements (REE). This District is approximately 135 km by 12 km in size, and is highly prospective for heavy and light rare earth elements. A total of 11 REE prospects have been discovered in the District to date, including the Foxtrot. In addition, Search is exploring in the 100% owned Henley Harbour region and has joint ventures with Quest Rare Minerals in the Strange Lake region, and with Great Western Minerals Group in the Red Wine complex, all in Labrador. These exploration locations are illustrated in the Figure 1. The focus of this paper is the investigation of the mineralogy and processing of Foxtrot REE materials. The Foxtrot resource falls within the claims held by Search in the Port Hope Simpson REE District. The infrastructure available at Foxtrot is excellent with a deep water port, air strip and road and power infrastructure at Port Hope Simpson. Over $7 Million has been spent to date on exploration and development of the District. The Foxtrot has been explored using prospecting geochemical methods, geophysics (airborne and ground), channel sampling of surface outcrops, mapping and three phases of drilling (18,934 m total)."

Jan 1, 2012

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2012

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Red mud has been reported as a potential resource for lithium. To investigate the leaching behavior of lithium, a lithium-rich red mud was neutralized with hydrochloric or oxalic acid and then leached with acetic acid. When red mud was neutralized using dilute hydrochloric acid, about 58 to 60 percent of lithium was leached with 25 percent acetic acid at 95 °C for 60 min, while more than 95 percent of sodium and 85 percent of calcium were dissolved in the leachate solution. When oxalic acid was used to neutralize red mud prior to acetic acid leaching, lower lithium leaching efficiencies of about 42 to 47 percent were observed. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the same conditions. In this study, 25 percent (v/v) of acetic acid at 85 °C for 60 min was demonstrated to be the optimum conditions for lithium extraction from oxalic acid-neutralized red mud using acetic acid. The results are useful and of interest for lithium recovery and purification from red mud.

By R. R. Boucher, O. J. C. Runnalls

A pronounced thermal effect has been observed on heating or cooling a1wninum-rich Al-U and Al-Pu alloys. From microscopic and X-ray diffractionstudies, the effectl has been attributed to trnsfor)nations in the inlemetallic phases UAl, and PuAl , involuing rearrangement or cluslering of vacancies The transformation obsrved in Al-20 wi oct U alloys occurred near the a Al-UAl4 eutectic tem-perature of 646°C making it difjicult to detect from heating curves. When cooling, howeoer, thermal mad X-ray analyses indicnted that the high-temperati~re phase labeled p UAL, precipitated initially during euitectic solidification. As solidification continued and after an induction period o-f 5 lo 20 tnin the nu-cleatiorz and growth of the low- twmperature phase, a UAl4 produced an euolution of energy which raised the observed alloy temperature by 1° to 2°C. in Al-Pu alloys the transformation occurred at 645°C, 5 deg below the eutectic solidification temperccture. The eslimated latent heat of transformation was 25 +5 cnl per g PuAl,. The high-tetnpevcl-ture forms of UAl, and PuAl, were easily 9-etccined by chill casting Al-U and Al-Pu alloys and on reheating the alloys the trcltzsforrnation to the a phase was sluggish even above 600°C. Separated single cryslals o-f UAl4, joy example, showed no evidence Of transformalion after heating for 16 hr at 620°C. The transformation rates increased yapidly enough with increasing temperature, however, that a a spontaneous liberation of energy lens observed on occasion when bealing cast Al-20 wt pet U to neal- the RECENT phase studies on A1-Pu alloys have indicated that earlier reported equilibrium diagrams should be modified to take account of several poly- morphic transformations in the intermetallic compound PuAl,.' During the course of the latter work an unexpected heat evolution was observed while cooling a solid alloy consisting of a mixture of a aluminum and PuA1,. The evolution occurred at 645°C, y below the a A1-Pu A1, eutectic solidification temperature. Subsequent thermal-analysis experiments with A1-U alloys showed that heat was evolved there also at a temperature nearly coincident with the a A1-UA1, eutectic solidification temperature of 646°. A search of the literature revealed that similar thermal effects had been observed before for both A1-U and A1-Pu but had never been fully explained.2,3 The purpose of the present paper is to describe thermal-analysis and X-ray diffraction experiments which have led to the conclusion that the thermal effects are due to transformations which involve the rearrangement of vacancies in the intermetallic compounds UA1, and PuA1,. EXPERIMENTAL PROCEDURE The A1-U alloys were prepared by heating super-pure aluminum (99.99 pct +) obtained from the Aluminum Co. of Canada in a graphite crucible surrounded by an induction coil. At 1000°C high-purity uranium metal produced by the Eldorado Mining and Refining Co., Ltd. was dropped into the liquid aluminum and was dissolved completely within 15 min. The impurities in the uranium were A1—4 ppm, Ca-4, C-70, Cr-3, Cu-6, Fe-30, Mg-2, Mn-10, Ni-25, Si-25, and Zn-2. The A1-Pu alloys were prepared by reacting plutonium dioxide with liquid aluminum under cryolite (3 NaF . AlF,) for 10 min at 1100°C in graphite crucibles exposed to the air. The plutonium was 99.8 pct pure, containing trace impurities of Ca, Cu, Fe, Pb, Si, and Zn. The liquid alloys were usually poured into water-cooled molds to provide castings of uniform composition from which samples could be cut for heat treatment and thermal-analysis experiments.

Jan 1, 1965

By Chulho C. Song, Liam Coleman

Alkaline pressure oxidation (POX) is an oxidative pre-treatment option that is commercially used for high-carbonate sulfidic gold ores. The high carbonate grades within the feed ore shifts the ideal operating pH to a basic regime. Compared with acidic POX, alkaline POX typically requires additional steam input due to a lower sulfur oxidation load and a high rate of in-situ carbon dioxide generation that needs to be vented along with steam. The cost of this steam addition is the largest differentiator between acid POX operation and alkaline POX from a cost comparison. However, alkaline POX can offset these costs through reduced acid usage for pre-acidulation and decreased alkali reagent consumption for subsequent neutralization. This paper reviews the specific operating cost impacts of acid/base consumption between alkaline and acidic POX with ores which require pre-acidulation, the overall economics of alkaline POX, and the regimes in which alkaline POX is economically favorable. The findings aim to guide industry professionals in making informed decisions for alkaline POX adoption by providing a summary view of its operational benefits and costs, contributing to the development of cost-effective and sustainable gold ore processing techniques.

Feb 1, 2025

By Ronald T. Mayerle

In-1992, the U.S. Bureau of Mines conducted a mineral investigation of the Anderson Mountain study area, including RARE II area 4-942, in Lemhi County, Idaho. The 7,340-ha study area lies within the Salmon National Forest about one kilometer north of the old mining town of Gibbonsville (pop.: 100). The eastern boundary of the study area is formed by the crest of the Bitterroot Range. The crest also serves as the continental Divide, and as the border between Idaho and Montana. The study area lies within the Gibbonsville Mining District, an important past producer of gold from lode and placer deposits. Since the 1870's, several hundred claims for both types have been located in the study area. Thirty-six current (1992) lode claims and two patented claim groups (one lode and one placer) are wholly or partially in the study area. No placer claims are current. In all, twenty-seven lode and five placer properties in and adjacent to the study area were investigated. Workings on the properties included 2 caved shafts; 36 caved adits; 8 open adits; 120 small pits, cuts, and trenches; and 4 large dozed cuts.

Jan 1, 1993

By J. Partyka

Respirable dust produced during blasting operations in underground mines exhibits both diffusion and convection properties of the airflow. However, the application of the mathematical model presently used to calculate the change in time in the concentration of blasting pollutants is mostly limited to a single drift and cannot be easily utilized for blasts taking place in stopes. This paper discusses an analytical solution based on considerations that enable us to reliably identify the initial condition. Such an approach may be used for any blasting area regardless of its position, its size, or the ventilation system in use during blasting. In addition, a test procedure using field data is established to determined those parameters not measured directly. As well, equations are derived to find the diffusion coefficient, and the position and size of a dust source from the field data. Mathematical considerations The convection-diffusion problem, for a one-dimensional case, is described by the following partial differential equation (PDE): ct. = Dcxx - Vcx + source - sink(1) where C = the concentration of a pollutant T = time V = the mean air velocity in x-direction D = the diffusion coefficient X = distance away from the pollutant source source = any additional pollutant source specified by an initial value problem sink = decay of a pollutant inside the region specified by the boundary conditions. Respirable dust produced during blasting is best considered as an initial value problem (IVP). To derive a mathematical model, the following assumptions are made: •At time zero (t = 0), the dust source is at point x = 0 of an infinite drift. •The problem is considered a one-dimensional case. •The mean velocity of air and the diffusion coefficient are constant. •There is no source or sink of dust other than specified at point x = 0 and time t = 0. We have to solve the following problem [PDE ct=Dcxx-Vcx-m<x...m;0<t<m(2)] ICc(x,0)=f(x)t=0, the initial condition Where c = dust concentration in mg/m3 V= the average mean velocity in a drift in m/s t= time in s D= the diffusion coefficient in m2 /S x = distance coordinate in m. We observe that in problem (2), we have moved the boundaries to[ -m and +m] in order to have an initial-value problem. We introduce new coordinates, s = t and z =x - Vt. To rewrite the PDE in terms of (z, s), we use the chain rule ct = czzt + csst = -Vcz + cs cx = czzx = cz cxx = (cz)x = czz. We now substitute our computed ct, cx. and cxx into the PDE to get new IVP in terms of z and s :

Jan 1, 1991

By Antti J. Perala, Teemu J. Yli-Kovero

"Efficient use of land is constantly requiring more underground construction. Minimized execution time and disturbance to surroundings and nearby structures are essential benefits for all construction techniques. To meet the demands of a modern construction project, suppliers have to be able to provide high-quality and tailor-made products just on time. RD pile wall is a retaining wall based on drilled steel pipe piles which are connected to each other with special interlocking profiles. RD pile wall is a solution which enables penetration of overburden soil, dense fill layers including stones and boulders, and embedding into the bedrock in one single operation. Several test installations and laboratory tests have been made to develop the system and to test and improve the water tightness of the wall. Beside these tests, RD pile wall has also proven its reliability in almost 70 projects. Largest project so far has been Pasila Tripla project in Helsinki, Finland. A permanent retaining wall with surface area of 18,000 m2 (193,750 ft2), excavation depth of 21 m (68 ft) and over 17 m (56 ft) of water pressure was made with 711 mm (28”) and 406.4 mm (16”) pile sizes. Piles were delivered to site in one piece with lengths up to 33.5 m (110 ft).INTRODUCTIONExcavations in cramped city centers and in between of existing buildings and other structures are facing more and more challenges. Installation of sheet pile walls is often problematic or even impossible due to obstacles in ground from old structures and due to demand to extend the excavations to even deeper and harder soil layers. Also installations of secant pile walls are facing difficulties due to cramped construction sites and constantly tightening execution times.On the other hand, an efficient and reliable piling technique suitable for the demanding soil conditions described above, percussion drilling, has been developed since the 1960’s, and especially from the mid- 1990’s, when the concentric drilling method with the ring bit and pilot was introduced. A new retaining wall application, the RD pile wall, was developed by combining that drilling method with the widely used retaining wall solution based on steel pipe piles and welded interlocks (a pipe pile wall normally installed with vibratory or impact hammers).PRINCIPLE AND MAIN BENEFITS OF THE METHODRD pile walls can be used in all soil conditions. Most beneficial the system is in extremely demanding soil conditions where the installation of traditional retaining walls is challenging or even impossible. The RD pile wall is a combination of drilled steel pipe piles and interlocking sections as shown in Fig. 1.Individual RD piles are connected to each other with interlocks welded to the piles on the automated welding line at the workshop. The matching dimensions of the drilling system and interlocking sections allow the installation of RD piles through stones and boulders and even into the bedrock, if necessary, in a single operation. Installation is done by a down-the-hole (DTH) hammer using the centric drilling system and oversized ring bits or a drilling system consisting of a pilot bit and reamer wings shown in Fig. 2."

Jan 1, 2017

By H. R. Babitzke

To develop alloys suitable for use at elevated temperatures, columbium and tantalum were combined with tungsten, hafnium, vanadium, zirconium, and titanium, and the resulting alloys were evaluated with respect to fabricability, hardness, Electrical resistivity, strength at elevated temperatures, oxidation resistance, and bend transition. Of the 23 compositions tested, Cb-2OHf-5W-10Ti exhibited superior high-temperature properties. A recrystallized sample of this alloy was fabricable at room temperature, had a strength of 44,000 psi at 1,200° C, and had an oxidation rate of only 7.7 mg/cm2/hr at 1,000° C.

Jan 1, 1966

By Alexander Blatt, Franz-Werner Gerressen

Diaphragm walls are known as underground structural elements commonly used as retention systems for excavation pits and shafts and permanent foundation walls or elements. One can anticipate that global urbanization and increasing demands on environmental considerations will need to be accommodated in underground space in the future. These trends show an increasing requirement for diaphragm walling in even more complex conditions, especially in inner-city applications with limited space. Complex conditions in terms of space limitations, especially for inner city job sites, require specifically adapted solutions for slurry, spoil, reinforcement and concrete handling and the related logistics to ensure smooth production. Furthermore, one focus will be given to the QA/QC topics of the production process. Real time installation control, data transfer and reporting systems become more and more important. Therefore, the paper will describe the construction method and the sequence of activities required for the construction of diaphragm wall systems. It will describe also the main equipment that will be needed to execute these works under various conditions. In addition to the general description of the system and the required equipment, the paper will show some site examples for infrastructure projects with their specific solutions when working under space restrictions.

Nov 1, 2022

By B. D. Thompson

Many mines adopt necessarily conservative backfilling strategies due to a lack of understanding of their backfill behaviour. In the past five years, extensive instrumentation campaigns have focused on measuring in-situ cemented paste backfill behaviour. These tests have resulted in optimised backfilling efficiency through elimination or reduction of cure periods where; i) controls on backfill behaviour are understood, and ii) barricade pressures are demonstrated to be within a safe range using routine monitoring as a required QA/QC procedure. Recently, this work has been extended to consider hydraulic backfill operations. Two stopes have been instrumented at Vale?s Coleman and Garson Ramp mines. The instrumentation and deployment methods are discussed, and representative total earth pressure, pore pressure, and temperature data are presented. In one case, pressures in the stope are relatively low as drainage causes strength gain in the fill and so pressures are arched. In a second example, again, drainage causes strength gain in the fill, but increasing temperatures correlate with pressure increases even during downtimes in filling. These pressure increases are thought to be caused by thermal expansion of the backfill in confined locations. Generally, the instrumentation approach has proven successful in measuring hydraulic backfill behaviour and offers good potential for incorporation into a procedure to safely maximise backfilling efficiency through routine barricade pressure monitoring, when combined with safeguards to ensure adequate fill drainage.

Aug 1, 2013

By T Takayama, R Muroi, M Matsumura

The steel industry occupies 14 per cent of CO2 emissions in Japan, and the sintering process is one of the major emitters. Since most of CO2 released from the sintering process comes from coke fine combustion, replacement of coke fines with biomass char as bonding agent is a potential countermeasure. In order to explore the effective use of biomass char, we chose char made from Palm Kernel Shell (PKS) as a sample. First, the char’s combustion behaviour was examined with varying the char’s particle size by means of admixing the char in alumina ball packed bed placed in an electric furnace. As a result, the finer the PKS char the faster the burning rate and reaching a higher temperature compared to coke fine. In addition, it is also concluded that the optimum size of PKS char was larger than coke fines. Next, the effect of different heat profiles on sinter structure was examined by sintering tablet made of chemical reagents. In this experiment, the chemical composition is designed based on sinter composition. By this sintering test, even at high temperature, rapid cooling is effective to make fine sinter matrix and fine pores, which has possibility for high sinter reducibility. Based on these two experiments, using PKS char as a sinter fine source has the possibility to improve sinter reducibility.

Nov 8, 2021

In 1962 and 1963, two in situ combustion pilot tests were conducted in the shallow Second Venango sand near Reno, Pa. Because of poor oxygen utilization and lack of production response, both tests were considered failures and were terminated. The area was then relatively inactive until late 1966, when a development well drilled near the 1963 test site had surprisingly good production in what was considered to be a pressure-depleted reservoir. Other wells drilled in and around the old thermal pilot areas also came in as good oil producers. This report presents a study of the increased oil production from the Second Venango sand in the Reno area, and the apparent connection of the present production response and the old thermal pilot tests. Apparently combustion occurred in the Second Venango sand after the 1962 and 1963 experiments were terminated and, supported by large volumes of air left in the reservoir after the 1963 test, generated carbon dioxide which helped repressure the formation. This field evidence of combustion warrants another pilot experiment to further explore the use of properly designed in situ combustion techniques in increasing production from the Second Venango sand.

Jan 1, 1971

By S. Tuylu, D. Adiguzel, A. Bascetin

"In recent years the fact that mining tailings cause serious environmental problems resulted in increasing number of studies about their disposal, storage and usability in various areas. Therefore the new studies about using the tailings for some purposes such as using in shotcrete or producing concrete have been increasing recently. The study is focused on applicability of tailings for producing shotcrete. Under this scope it is considered that mining tailings can bring many advantages in case of that they are used instead of sand, silt or fine aggregate in shotcrete applications. Most important advantages can be listed as decreasing shotcrete cost, decreasing amount if mining tailings to be disposed and the contribution to be provided on sustainable production of sources. The main objective of this study is the investigation of using mine tailing instead of fine aggregate in shotcrete. In this study, 10 shotcrete designs in different proportions were formed, and properties of the mixtures were identified. Then, the experimental results were statistically analyzed, the effects of the amount of the tailing material used on shotcrete properties were presented, and empirical approaches that can be used for the estimation of these properties were developed. INTRODUCTION The disposal of high amount mine tailing on the surface is caused a lot of problems in terms of environmental impact. Unfortunately, it is known that classic disposal techniques such as tailing dam cannot provide a solution these problems. The tailing dams which are usually used in the disposal of mining tailings bring along many problems in terms of cost, environment, and human health. So mine tailings are used in different production such as shotcrete. This technique is becoming increasingly common during recent years. The usability of mine tailings in brick and concrete production instead of cement and fine aggregate has been studied by many studies [1-4]. This situation has been promising for the usability of tailings in shotcrete which is commonly used for ground support especially in tunnels. Shotcrete (sprayed concrete) is applied mainly for construction of tunnels, shafts, renovation works and strengthening of slopes. Main advantage of shotcrete is fast development of strength, which quickly ensures stability of strengthened structure [5]. Shotcrete can be defined as spraying the grout consisting of water, aggregate, cement and optional additive mixture on the desired surface with a compressed air. According to the definition of the American Concrete Institute (ACI), it is the spraying of sprayed grout or concrete on a surface at high speed with air pressure [6]. In recent years, the use of shotcrete for the support of underground excavations is decreased in the mining industry. The design of shotcrete support for underground excavations is a very imprecise process. Strength and pumpability properties of shotcrete are very significant for determining suitable shotcrete design. Flow characteristics of the shotcrete must be determined for pumpability and fluidity of the material."

Jan 1, 2017

By T. W. Cavers

The Dwight-Lloyd sintering machine was the answer to the flue-dust problem of the copper blast-furnace smelter. Then came concentration by flotation, which threatened to eliminate the blast furnace from the smelting field altogether, and again the sintering process solved the problem. As is well known, the sintering process is dual in its function; it expels sulphur from the charge and it converts a powdery material into nodules or chunks that hold together. The charge is ignited on top just as it passes over the edge of the first suction box, and the oxygen of the air that is drawn downward through the charge breaks up the sulphide and oxidizes about fifty percent of the sulphur. The heat produced by this reaction in the upper stratum of the charge ignites that lying immediately below, and, when the pallett has travelled the full length of the machine, the tire has reached the graces and the fine concentrate has changed its characteristics by being partially fused and has become a more or less solid mass. When the Granby Company was smelting its ore as mined, one small D-L machine was adequate for the treatment of the flue dust, but as soon as the policy of smelting the concentrate was adopted, it became necessary to add two large machines to the sintering plant. The three sintering units, of which two are 42 in. by 396 in. and the other 42 in . by 264 in. in hearth area, have a combined capacity of from 370 to 450 tons (dry) of charge per day. The capacity varies directly as the hearth area. The sinter produced is about 88 per cent of the dry charge, or 325 to 400 tons per day. The sintered fines returned for resintering average between 30 and 35 per cent of the charge, but this is not as great a disadvantage as might appear, since the addition of hot fines improves the burning qualities of the mixture. From 50 to 54 per cent of the sulphur is eliminated in the sintering operation.

Jan 1, 1934

By R. G. Robins

The effective removal of arsenic(V) from process streams and waste waters by precipitation with excess iron(II1) is sometimes attributed to the formation of basic ferric arsenates. The authors have investigated this system extensively using a variety of techniques and conclude that the solid phase produced is iron(II1) oxyhydroxide (ferrihydrite) with arsenic(V) adsorptively bound to the 2-3 nm particles.

Jan 1, 1992

By Arístides Sotomayor

El presente texto señala la importancia del oro a nivel financiero y minero ya que los inversionistas suelen utilizar este metal para obtener ganancias debido al mínimo riesgo existente en la pérdida de su valor comparado con otras divisas. Así, se estima que en el Perú, existen 480 unidades mineras de oro, de las cuales 28 concentran cerca del 90% de la producción nacional, como la Minera Yanacocha, Minera Barrick, Compañía de Minas Buenaventura, Consorcio Minero Horizonte, Aruntani y Aurífera Retamas. Entre las dos regiones que producen mayor cantidad de oro está: Cajamarca y La Libertad ( 38%) y la tercera región es Arequipa, seguida por Madre de Dios (9%).

May 1, 2016