Search Documents

By Ralph H. Nafziger

The Bureau of Mines, in cooperation with the Idaho National Engineering Laboratory, has electroslag melted a V-5Ti-5Cr alloy using a fused CaF2, flux. The alloy is a candidate for use in future fusion reactors. One objective of this research was to evaluate the feasibility of the electroslag melting process in separating simulated radioactive isotopes from the V alloy to demonstrate recyclability. Small amounts of Ca, Y, and Mn were added as surrogates for radioactive isotopes. Results showed that this vanadium alloy can be electroslag melted satisfactorily. The impurities added intentionally were removed or decreased successfully. Among the major alloying constituents, Cr was retained but there were some Ti losses. The latter may be controlled with process refinements. This research suggests that the electroslag melting process could be a suitable method for recycling V alloys after use in future fusion reactors, or for processing other reactive metal alloys with more immediate applications.

Jan 1, 1996

By J. -M. Lopez-Cuesta, C. Petter, B. Otazaghine, M. Batistella, R. Sonnier

"Kaolinite is a dioctahedral aluminosilicate widely used as paper filler and coating pigment. At the best of our knowledge, kaolinite is not widely used in polymer industry. Therefore, in this study, the flame retardant effect of kaolinite in ethylene vinyl acetate copolymer (EVA) and polypropylene (PP) were studied and compared with an alumina trihydrate (ATH) and Talc. Cone calorimeter results shows that the weight percentage of ATH in EVA/ATH composites must be at least 50 wt. % in order to reach an improvement in fire retardancy in terms of pHRR. In the case of EVA/kaolinite, even with 35 wt. % the pHRR is largely reduced. Comparing PP/Talc and PP/kaolinite composites at 30 wt. %, both fillers leads to same reduction in pHRR with a slightly better performance for PP/kaolinite composites. In both cases an intumescent behavior of kaolinite composites was observed that could slow the rate of the rising degradation products, allowing radical recombination reactions. Also, it was observed that kaolinite forms a protective layer on the surface of the samples, which could insulate the material. These behaviors (intumescence and formation of a protective barrier) could reduce the transfer of the degradation products to the flame and explain the better performance of kaolinite composites. INTRODUCTION The use of mineral fillers as fire retardants in polymer matrix are well known and widely studied [1]–[10]. Aluminum and magnesium hydroxides (respectively ATH and MDH) are the most widely used inorganic fire retardants. To achieve fire retardancy with these mineral fillers, about 50-60% loading is required which decrease the physical properties of the composites. The fire behavior of composite EVA has been the subject of many studies [4], [7], [9]–[15]. EVA copolymers are commonly used in the cable industry, due to their high ductility, even at high loading rates. In such applications, the flame retardant systems should be introduced into the polymer to improve the fire reaction. Many flame retardant systems have been tested but the most used industrially relates to formulations based on hydrated mineral fillers (aluminum hydroxide and magnesium hydroxide). Their low cost and reduced fumes generation explains their success. However, to obtain good performance with this type of flame retardants, it is necessary to incorporate high levels (up to 65 wt %), which severely impact other properties such as processability and mechanical behavior. The main modes of action of these flame retardants are the dilution of the gas phase, the endothermic decomposition and a barrier effect created by the inorganic oxide residue which may be improved by the incorporation of other components such as montmorillonites, silicas or talcs."

Jan 1, 2015

By D. P. Wilkinson

Flow field design is critical to determining fuel cell performance with respect to operating conditions. Flow fields are normally designed around their maximum power operating point with the goals of maximizing performance and minimizing pressure drop between the inlet and outlet of the flow field. At lower power pressure drop is reduced, and water management and reactant distribution issues can occur over the active area as well as issues with cell to cell reactant distribution in the fuel cell stack. Flow fields have fixed flow channel geometries and fixed active areas which determine the reactant flow characteristics over the operational range of the fuel cell. In this paper we discuss some of the benefits of a new approach of changing the flow field active area with changing operating conditions. Such benefits for future fuel cell designs could include improved cell performance and stability, improved cell to cell reactant distribution, reduced low current density failure modes, and overall system advantages.

Jan 1, 2005

By G. D. Marshall, D. K. Sarin, V. E. Hampton

Ground support at the Thompson Mine emphasizes scaling, rock bolting and wire mesh screening on the backs and walls of all underground stoping and development areas and also full column grouted cable bolting in the bulk mining areas. This paper describes the equipment for the point anchored rock bolts as well as the full column cable bolts. Modifications in design and testing of all components and procedures has ensured a safe and efficient method of ground support for the mining conditions existing at the Thompson Mine.

Jan 1, 1983

By L. Cheng, M. S. Seehra, P. S. Raghoottama

The four major IR bands of a-quartz at 1080, 797, 693 and 488 cm-1 are studied at room temperature by FTIR-Photoacoustic Spectroscopy. Using Rosencwaig-Gersho theory, equations for the PAS signal q for the thermally thin and thermally thick cases are derived and it is shown how thin to thick transition occurs and leads to saturation as the sample mass is increased. For sample mass < 2 mg, q is proportional to sample mass thus defining the region for quantitative analysis. The dependence of q on the chopping frequency f is found to vary as q f-n with n ? 0.9 for quartz, in good agreement with the RG theory.

Jan 1, 1989

By E. W. Davis

The mixing of fine ores with fuel and burning under induced draft is called sintering in iron-ore practice and either sintering or roasting in copper and lead metallurgy. The first development of sintering was the Huntington-Heberlein process, in which fine sulfide ores mixed with fuel were charged into a pot and burned under the action of an upcast current of air introduced at the bottom of the pot. Modern development has resulted in two types of machine; the continuous Dwight-Lloyd machine, which consists of heat-resisting grates and a moving beltlike type of hearth constructed of metal, in which air is drawn downward through the bed, and the stationary Greenawalt batch process, which operates in the same manner as the Dwight-Lloyd except that the hearth is stationary. The recent rapid increase in the use of sintering has been the result of two great advances in metallurgical process—flotation and the treatment of flue dust. The Dwight-Lloyd machine is used in many plants for agglomerating flotation concentrates and at the same time reducing the sulfur content to furnace requirements and it has become standard practice to treat iron blast-furnace flue dust by either the Greenawalt or Dwight-Lloyd machine, so that it can be recharged into the furnace. The mining of low-grade magnetite iron deposits and their beneficiat-ing by grinding and magnetic separation resulted in a fine concentrate extremely detrimental to blast-furnace practice. These concentrates are sintered and made into ideal material for blast-furnace use. Incidentally, coke savings of about 400 lb. per ton of pig are reported. Sintering at Evergreen Plant The application to limonitic iron ores is the most recent development of the sintering process. The first plant in the Lake Superior region was erected by the Minnesota Sintering Co., a subsidiary of the Evergreen Mining Co., at Ironton, Minn., in 1924. This plant was designed to treat Cuyuna Range iron and manganiferous ores containing low silica, high moisture and a structure objectionable because of a large proportion

Jan 1, 1930

By Yong Pan, Srivatsan Jayaraman Sridharan, Purushotham Tukkaraja

Block cave mining method poses unique ventilation challenges compared to other underground metal mining methods. This research study focuses on assessing the airflow behavior in regulated airflow distribution systems by developing a 1:100 scaled block cave experimental model and a numerical model. This study also investigated gas flow behavior under various airflow conditions. Based on our findings, we observed that reduction in particle size and porosity of caved materials, decrease in cave footprint, and closure of undercut drifts would increase cave airflow resistance. The increased airflow is found beneficial for gas dilution regardless of its source locations, while the regulated airflow distribution system might deteriorate gas dilution situation when the source is located in the extraction drifts.

May 12, 2022

By Earl F. Hastings

The Pilgrim mine, operated by the Pioneer Gold Mining Co., is 9-1/2 miles west of Chloride in the Pilgrim mining district on the eastern slope of the Black Mountains, or River Range, Mohave County, Ariz. In March 1937, 100 tons of gold ore per day were being mined and milled at the property by a total force of 5i men. Climatic conditions allow year-round operations. Due to present activity in the county there is an ample supply of labor for the requirements of the mine. The Pilgrim is the only producing property within s radius of 6 miles; recently, however, the South Pilgrim Mining Co. has launched a development campaign on claims that adjoin the Pioneer Co. property to the south.

Jan 1, 1937

By E. W. Murbach

The oxidation of uranium carbide by oxygen at various pressures, and by air, has been investigated at temperatures up to 600°C. Arc-melted and cast uranium carbide displays oxidation behavior that appears to be dependent on its treatment after melting. ccReactive" uranium carbide, which results from exposure of freshly melted material to laboratory air, ignites in oxygen at about 275° to 350°C depending on pressure, and in air at about 350°C. The product of the initial oxidation appears to be UO2+.. Continued heating produces U30,. The initial oxidation rate is poportional, roughly, to the square root of the oxygen pressure. The activation energy determined for the initial oxidation reaction is 7.1 kcal, from 400° to 600°C in 10 mm of oxygen. AN investigation of low-decontamination methods for reprocessing uranium carbide reactor fuels is being carried out at Atomics International. One of the reprocessing cycles includes oxidation of the fuel at relatively low temperature (300° to 500°C) and reaction of the product oxide with carbon at elevated temperatures (above 1500°C) to produce uranium carbide. A number of small-scale experiments have been carried out in which uranium carbide was oxidized in air and oxygen at various pressures to measure reaction rates and to obtain other information concerning the oxidation process. In initial experiments with arc-melted UC, ignition was observed at about 275°C in oxygen or 350°C in air. However, similar experiments by Neymark&apos; at 426°C in air showed no ignition. It was soon determined that the difference in oxidation behavior was due to the treatment of the UC following arc-melting. Neymark&apos;s experiments were carried out with freshly melted UC while those reported in the

Jan 1, 1963

By W. Pariseau, S. Puri, S. Schmelter

Introduction Joints often have profound effects on elastic properties and strength of rock masses and therefore on rock slope stability. In surface mine slopes, joints are usually too numerous to be taken into account individually, so an equivalent properties approach is necessary. Previous work that treats a jointed rock mass as an equivalent composite material of joints and intact rock between resulted in excellent agreement between estimated and true rock mass elastic moduli in case of fully persistent joints (e.g., Pariseau, 1999) Rock mass failure mechanisms on joints and through intact rock were retained obviating the need for an equivalent rock mass strength. Impersistent joints, which are not continuous on a joint plane, can be accommodated (Pariseau, 2003). However, slope stability analysis of a large, deep copper mine indicated a need for computational efficiency even in two-dimensional analysis of vertical sections through pit walls (Puri, 2006). The analyses by the popular finite element method used small elements of bench size near the pit slopes and much larger elements away from the pit walls. The reasons for the graded meshes were numerical quality (small elements) and computational economy (large elements). Small elements contained only a few joints, while the larger elements contained hundreds of joints and led to impractical computation run times (days!). A new modeling procedure that recognizes sufficiently large elements as representative volume elements (REV’s) overcomes this obstacle. A companion improvement recognizes the concept of a representative area element (RAE) in association with joint impersistence and the probability that joint material occupies a considered site. Both are steps towards greater model realism and a practical slope stability analysis procedure. Consider the open pit mine photo shown in Figure 1(a), a companion plan view in Figure 1(b), and the problem of slope stability where high slope angles favor economics but low slope angles favor safety. These competing factors in surface mining generally result in some sections of the mine that have unstable slopes that require monitoring and perhaps mitigating action to improve stability. Although stability of a given section may not be easy to quantify with a single number, useful design guidance can be obtained from a finite element analysis of a proposed mining sequence leading to future pit slopes and profiles. The presence of water from rain and snow melt indicates a need for a coupled analysis that links water pressure, effective stress and total stress (Schmelter, 2001).

Jan 1, 2007

By D A. Deglon

Solids suspension is important in the design and operation of mechanical flotation cells, and is a necessary precondition to particle collection. Most of the fundamental hydrodynamic research that incorporates some aspect of solids suspension was done by Arbiter, Harris, and co-workers, or Schubert and co-workers. However, a need for research into solids suspension in mechanical flotation cells exists, since very little has been done since the late 1980s; a time that also coincides with the advent of round mechanical flotation cells and the subsequent dramatic increases in maximum flotation cell sizes. In this work, concentration profiles and critical impeller speeds, Njs, were measured in a 0.124 m3, round cell fitted with a 0.150 m, Bateman impeller mechanism. Two solids size fractions (75 - 106 and 150 - 250 ¦m) were tested, in ungassed and gassed conditions (JG = 0, 1 cm/s) and at various impeller speeds (300 - 900 rpm). The effectiveness of solids suspension was quantified in three ways in terms of extent of off-bottom solids suspension, suspension height (extent of solids distribution), and variation within the solids distribution, which together present a complete quantitative picture of solids suspension and distribution within the cell. Consistent trends were found when these effectiveness criteria were considered against relative impeller speed, in terms of percentage of critical impeller speed, N/Njs. Off-bottom solids suspension is complete at or above 100 per cent of Njs, with significant sedimentation occurring as the impeller speed drops below 60 per cent of Njs. Suspension heights consistently reached a level equivalent to 90 per cent of the tank diameter at the critical impeller speed, and dropped off significantly as N/Njs dropped below 60 per cent. The variation in the solids concentrations within the sampled profiles showed consistent trends in two-phase but not under three-phase conditions. The paper concludes that the critical impeller speed, Njs, commonly used in the design and operation of standard stirred tanks, is a very useful solids suspension benchmark for describing all aspects of solids suspension in mechanical flotation cells and should be correlated to system conditions.

Jan 1, 2005

By R. H. Storch, D. C. Holt

During reconnaissance investigations of more than 300 stream areas in Idaho to determine the potential value of ilmenite in black - sand placer deposits 46 deposits were explored by churn drilling , trenching , test pitting , or shafting . The component mineral content and total black - sand content were determined for more than 8,690 reconnaissance and exploration samples . Data compiled during the investigation indicate a good potential for large , low- grade deposits containing ilmenite , monazite , columbite , euxenite , uranothorite , and other radioactive black minerals and accessory black - sand minerals . The data also indicate most deposits will be economic only if several component minerals can be recovered as coproducts .

Jan 1, 1963

By Lloyd M. English

Accurate knowledge of the gas content of coal seams has always been important, according to the work of W. P. Diamond and J. R. Levine, 1981, but is becoming increasingly important for several reasons: Excessive gas emissions in the mine can create explosion hazards. Depletion of shallower coal reserves is forcing underground operations to greater depths where coal gas content is often greater. Natural gas prices and the need for new energy sources make naturally occurring coal gas a potential resource of economic interest. Information on coal gas content will impact mine designs, mine ventilation system specifications, and the effectiveness of methane control procedures used. Accurate resource assessment is needed for projecting and designing potential gas utilization enterprises. The emphasis upon methane hazards in mining operations, and upon potential methane utilization, has led us to improve upon the procedures used to determine coalbed methane levels.

Jan 1, 1984

By G. Grassmück

The question of whether the air curtain principle could be used under conditions prevailing in Canadian metal mines was investigated. A vertical, portable BERRY air curtain was tested, at first in a wind tunnel built at Ecole Polytechnique at full scale (8-by 8-ft cross section) to simulate a drift and its lateral connections, and then in the haulage ways of a metal mine under actual conditions. The results permit us to predict under what conditions this type of air curtain is capable of acting as an air stopping or flow regulator and how it could be further developed.

Jan 1, 1969

"The objective in controlled blasting is to reduce overbreak to control the final pit wall slope, shaft, drift ditch, bench, etc. to the final planned excavation limit. The six main types of controlled blasting utilized today are:1. Line Drilling2. Cushion Blasting3. Smooth Wall Blasting4. Buffer Blasting5. Presplitting or Preshearing6. Air Deck Presplitting"

Jan 1, 1994

By M. Gangal

CANMET-MMSL, in cooperation with Dry Systems Technologies and Quinsam Mine, conducted a study to determine the effects of B50 biodiesel on the emissions of a flameproof diesel power package in comparison with mining diesel fuel for application in underground coal mines. The emissions testing for coal mine application requires that the intake air mixture to the engine should be at 1.25 percent methane by volume in air. The tested power package system included a naturally aspirated, mechanically-controlled diesel engine with a diesel oxidation catalyst (DOC), a heat exchanger, flame arresters, and a low temperature disposable diesel particulate filter. The engine dynamometer tests were conducted at the CANMET-MMSL Diesel Emissions Research Laboratory in Ottawa using the ISO 8178-C1 test protocol. The separate and combined effects of a B50 biodiesel blended fuel, and with and without 1.25% methane enriched intake air were measured on a diesel power package. Fuelling the baseline engine (without methane), with B50 biodiesel blend reduced carbon monoxide (CO) by 44%, and increased nitrogen dioxide (NO2) by 19%, and particulate matter by 31% relative to the mining diesel fuel. Similarly, injection of 1.25% methane to the intake air for baseline engine with mining diesel fuel increased engine power by 15%, CO by 124%, and NO by 15%, and decreased NO2 by 13%. The effect of B50 biodiesel relative to the mining diesel for coal mines application (with methane for both fuels) was to reduce CO by 27%, and NO by 6%, and increase NO2 by 23%, with no change in engine power. The overall results indicate that the minimum ventilation rate for the equipment application in coal mines with B50 biodiesel was 4.11 m3/s (8,700 cfm), slightly higher than the ventilation rate of 4.01 m3/s (8,500 cfm) with the mining diesel fuel. This slight increase in ventilation rate for B50 biodiesel fuel was due to an increase in NO2 at one of the operating test points, and the ventilation rate for this equipment was governed by NO2 in the exhaust gas.

Jan 1, 2009

By G. Roberts, S. S. Klima, W. R. Reed, J. Deluzio, G. Ross, A. Mazzella

The abstract discusses the problem of silicosis among roof bolter operators in coal mines due to respirable quartz dust (RCS) exposure. It presents a study comparing a new wet box collection system to the traditional dry box system. The wet box system uses water to saturate collected material, reducing RCS exposure during cleaning. The study found that the wet box system significantly reduced RCS exposures and quartz content in samples compared to the dry box system.

May 11, 2022

The drill steel&apos; sharpening shop, which stands adjacent to the Chaffers shaft, is built to the dimensions of 110 ft. 9 in. by 58 ft. wide, and is air conditioned in order to maintain reasonable working conditions during the summer months.Figure 1 is a plan of the shop, showing the disposition of the machines and equipment.LIST OF STEEL SHOP EQUIPMENTAir Conditioning Plant comprising:-1 Spray and Eliminator Type Air Cooler, 6&apos; ft. x 7 ft. x 6 ft. with 80 fine sprays.1 No. 36 Keith type ER. Ball Bearing upcast multivane centrifugal fan.20,000 cfm. a in. WG. at 450 r.p.m.Fan motor, A.G.E. S.C. 10 h.p. 1,160 r.p.m.1 Water Pump. 2?!-3-in. Thompson Class G. Single Stage Centrifugal Pump.1 Pump Motor, A.G.E. S.C. 70 h.p. 1,160 r.p.m.Drill Steel Sharpening Equipment:-2 Holman Sharpening Machines, No. 11.1 Ingersoll Rand Sharpening Machine, No. 54.5 Ingersoll Rand Sharpening Machines, No. 50.2 Holman Hot Millers, Type DM. Double Spindle Machines.2 Morgan Hot Millers, Type 1.6 Reamers consisting of motors with Ingersoll Rand Chuck fitted to the shaft and carrying a reamer of i-in. square Ultra Capital Steel Motors, A.G.E. S.C. 1 h.p. 1,160 r.p.m.4 Double-sided Drill Sharpening Furnaces, oil fired with L.P. &quot;Major&quot; 2-in. non-rotary whirl type burners.Combustion Chamber, 2 ft. 4 in. x 6 in. x 12 in. Oil consumption, 3&#183;3 to 3&#183;8 gallons per hour.Furnace Lining, Standard Kyanite.Firebricks, 9 in. x 3 in. x 4 in.2 Moving Frame type double-sided tip hardening furnaces, oil fired using High Pressure Air reduced to 3 lb. per square inch.Combustion Chamber, 3 ft. 5 in. x 5 in. x 16 in.Burners, &quot;Major&quot; L.P. 2-in. non-rotary whirl type.Oil consumption, 3&#183;3 to 3&apos;8 gallons per hour.Furnace lining-bottom and sides, 60 only 9 in. x 3 in. x 4 in. Kyanite bricks.

Jan 1, 1941

By P. E. Damon

An arsenal of isotopic techniques is avail-able that can date the full range of hydrothermal ore deposits. The following are prerequisites for ideal results: (1) Careful collection of samples that are related to the event in a field and process context; (2) Optical examination of the component selected for dating to be sure that it has not been altered; (3) Careful preparation of a pure component of the sample selected for dating; (4) Precise and accurate measurement; (5) Knowledgeable interpretation of the data with reference to decay systematics, properties of the component analyzed as well as the field context and thermochemical environment of the ore process.

Jan 1, 1992

By Michael J. Virnig, Keith E. Weerts

The development of heap leach technology for the treatment of low grade gold and silver ores has led to a boom in gold production in the Western United States in the last 15 years. The heap leaching process consists of stacking the mined ore on a specially prepared leach pad followed by leaching with dilute alkaline cyanide solution. Depending on the nature of the ore, it may require crushing and/or agglomeration prior to stacking on the leach pad. As the dilute alkaline cyanide solution migrates down through the stacked ore, the precious metal values along with a portion of the base metal values present in the ore are dissolved to give a pregnant leach solution which is collected at the base of the stacked ore. The precious metal values are then recovered by zinc precipitation or by adsorption on activated carbon. Once all of the economic metal values have been leached from the ore, the spent heap leach pad, the leached materials, and associated process solutions must be decomissioned. Decommissioning requires that the spent heap leach pad along with the leached materials and process solution be treated to reduce the concentration of the residual cyanide, base metal cyanide complexes, and other anionic metal species to levels where they no longer represent a long tenn liability for the environment and the operator. The levels to which these components must be reduced is dependent upon the applicable water quality standards as determined by the responsible federal, state, and local agencies. As environmental awareness has grown, these standards have become increasingly stringent. A number of treatment options have been developed for the de-toxification of the process residues. These include natural degradation which incorporates bio-degradation, fresh water rinsing, alkaline chlorination, hydrogen peroxide, and sulfur dioxide/air. Each of these options has been reviewed with regard to relative effectiveness, generation of hazardous by­products, reagent handling considerations, relative costs, and time requirements by Denton, Iverson, and Gosling I. As an outgrowth of the program to develop Henkel's guanidine based gold extractants, COGNIS, Inc., the environmental ann of Henkel, has developed the CyanoMet R process for the extraction and concentration of the various cyanide and anionic metal species from the dilute aqueous alkaline solutions generated during the process of detoxifying spent heap leach pads. This paper describes the CyanoMet R process, its application to three different feed solutions, and treatment of the concentrate generated by the process.

Jan 1, 1993