Search Documents

I find that during the short time I have been in this district, the majority of boilers are, and have been, receiving very bad usage owing to the difficulties which they have to contend against, viz., oil and bad water. Oil on the heating surface of a boiler is of a highly dangerous nature inasmuch as it allows the surface to become overheated, owing to the water not coming into direct contact with the plates, and it naturally follows that when the crown sheets of a flue or firebox become overheated, you lose a considerable amount of the strength of the plate, and the flue or crown comes down. Referring to the oil question, I find that too much care cannot or exercised on the part of engine drivers in order to minimise as much as possible the internal lubrication of the various engines under their control. For I consider that it is here that the most of the trouble is caused. My reasons for stating such to be the case, are:-That the majority of enginedrivers before coming to this field have been used to driving engines that have been exhausting into the atmosphere, and probably they have been taught that it is far better to use a little extra lubrication than to have a hot bearing. So far so good. But one thing that must not be overlooked is that on these fields the conditions are altered in this respect, as the majority of engines in this district are not exhausting into the atmosphere, but are condensing their exhaust steam and using the water so condensed for feed purposes.

Jan 1, 1901

By T. MacDONALD

ATHOUGH flotation has been a commercial process for over twenty years, the last two years have witnessed a sudden and phenomenal increase in our knowledge of how to separate minerals heretofore not considered amenable to flotation at all. As remarked by Professor Locke in the January issue. "Either commercial or laboratory flotation is reported on zircon, ilmenite, carnotite, kyanite, scheelite, chromite, fluorite, feldspar, cassiterite, wolframite, barite, and clay. Attractive patents on soap flotation are U. S. Nos. 2,000,656 and 2,040.187. A survey by Ralston in the February E. & M. J. adds many other minerals to this impressive list. The simple but pregnant fact is that any mineral can be coated, directly or indirectly, with a water-repellent coating, and since this is true, it follows that any mineral can be floated. Fundamentally, this is no new discovery, where, for instance, is the mineral that cannot he washed from a pair of dirty hands by means of soap and water, given the absence of refractory greases or oils which would have no proper place in flotation ?

Jan 1, 1937

By Hans von Michaelis

"INTRODUCTIONThe renaissance in gold and silver recovery technology has continued to unfold and it is appropriate to review some of the useful new technologies as well as try to identify some of the industry's future needs and frontiers.The remarkable strengthening in the US dollar has resulted in a relatively low gold price in US Dollars of around $310/oz at the time of writing and silver at $6.25/oz. This general softening in the dollar prices and the recent confusion as to environmental compatibility of cyanidation tailings and effluents, has led to a slowdown in announcements of new operations. Another reason for the slackening off in the USA is that in the past few years a large part of the capital has come from oi I and gas companies that now seem to be losing interest in mineral ventures, and foreign investors for whom the dollar is becoming out of reach. In the author's opinion this represents an unprecedented window of opportunity.Elsewhere in the world where local currencies have weakened, the price of gold is at or close to its all time high.For example, in South African Rands, the gold price was R571.00/oz when the rand was US$1.47 and the gold price reached US$800. Now at US $309/oz and with the Rand at US$0.51 = Rl .00, the local gold price is R600. The price of si Iver in Mexican pesos is not much less than it was when silver reached US$50/oz. Gold, and silver prices in local currencies outside North America are still buovant and at levels where additional investment in new projects is more encouraging.Even in Canada where the dollar is worth about US$0. 75, this provides a smaller but significant cushion compared with US operations. Considering the present strength of the US dollar and even the Canadian dollar relative to many other gold producing countries, there should be significant investment opportunities at today's prices. Mining companies have started to descend on Brazil, for example, where in a matter of just a few years annual gold production has increased from 10 to 70 tons. In South Africa, a Canadian company backed by Swiss financing has been able to take over a Witwatersrand gold mining operation and is installing a huge new tailin9s retreatment plant to process about 1 million tons per month of tailings."

Jan 1, 1985

By Karl C. Dean

All components of 15 automobiles manufactured between 1954 and 1965 were analyzed, and it was determined that a representative junk automobile would have the following composition (all figures in pounds): steel, 2,532; cast iron, 511; copper, 32; zinc, 54; aluminum, 51; lead, 20; rubber, 145; glass, 87; miscellaneous, 142. Time and motion studies and a cost evaluation were made to determine if such a typical vehicle could be economically burned in a smokeless incinerator and hand-dismantled, and if the resultant steel could be baled into a high-quality No. 2 bundle containing less than 0.10 percent copper. The cost evaluation showed that processing the composite car would cost about $51 to produce about $56 worth of marketable ferrous and nonferrous metal products and provide an annual rate of return on investment of 19 percent.

Jan 1, 1969

By Floyd Kelley

THERE is an ever-increasing demand for furnaces with controlled atmosphere, due to the large quantities of steel being used in the automotive industry, such as the .high-chromium stainless irons, the 18 Cr, 8 Ni stainless iron and low-carbon steel sheets. The difficulties involved in the annealing of such materials, if they are to be kept absolutely free from oxidation, are many. It is possible to bright-anneal these steels in small laboratory hydrogen furnaces, using specially purified hydrogen and taking some additional precautions. In the first place, the insulation, usually of alumina or magnesia, holds small amounts of water vapor, which it is almost impossible to remove completely. Secondly, there is always condensation of water vapor in the cooling chambers of such furnaces, and with the continuous circulation of the hydrogen gas in the furnace, the water vapor is carried from the cooling chamber back into the heating chamber. This water vapor oxidizes the charge. Lastly, the supply of moisture is made sure by the diffusion of small amounts of air from the atmosphere into the furnace against the pressure of the hydrogen. The oxygen combines with the hydrogen and forms more water. Under such conditions there is, little gained by using specially purified gas, because it becomes contaminated after reaching the furnace.

Jan 1, 1931

By Tristan Worsey, John Rathbun, Andres Malone

A run of mine, low grade gold heap leaching operation is currently looking to increase ounce recovery by decreasing run of mine fragmentation size. Current blasting practices have resulted in an average fragmentation size of 80% passing 7.05 inches (179 mm). It is estimated that a decrease of 2 inches (51 mm) in the 80% passing fragmentation size has the potential to yield up to a 2.5% increase in the overall life of mine recovery within this ore body. This potential recovery increase could lead to an increase in recoverable ounces which, in turn, would lead to a better profit margin. As this particular deposit is composed of predominantly low grade heap leach the capital investment in a crushing facility was cost prohibitive, it was therefore decided to look into the current blasting practices as a means to improve fragmentation.

Jan 1, 2015

By Bruno Gemmi

A new warehouse built with prefabricated components over an area underlined by soft marine soil deposits started showing differential settlements well before its completion. Its 103 spread footings carrying up to 4,000kN (450t) axial loads had been cast on jet-grouted columns extending and penetrating a layer of sand at a depth of 10m (33ft). Investigations performed to assess the wholeness and consistency of the jet-grouted columns revealed a state of loose jet-grouted masses and uncontrolled, off target migrations of the jet-grouting. Most of the jet-grouting itself was settling. The following remedial solutions were suggested: 1. Construction of new and better controlled jet-grouted columns. 2. Cement-based soil grouting. 3. Expanding resin injections. 4. Minipiles drilled-through the existing footings and reaching into a denser layer of sand existing at 23m below grade. Remedial solution 1. was immediately discarded due to cost and the possibility of a repeating failure in this non-granular and highly compressible soil. Tests of remedial solutions 2. and 3. were carried out. The outcome of the grouting was monitored by Electro Resistivity Tomography (ERT) (Bares et al., 2003), an innovative 3D electro tomography procedure showing where grout had been actually placed and its migrations off target. A successful 4,000kN (450t) load tests confirmed the validity of the solution. Finally, upon the completion of a successful load test, solution 4. was chosen. It supplied the highest degree of reliability thanks to the ease of controlling the final and actual location of the minipiles and to the higher safety factor provided. All remedial work to install the minipiles was eventually performed inside the building. Additional load tests and settlement measurements confirmed the adequacy and success of the chosen solution.

Jan 1, 2011

A commonplace, sometimes overlooked or taken for granted, article of everyday existence is the tin can. Produced from thin gauge low carbon steel, and commonly coated with a mere 60 millionths of an inch of pure tin, the product is however strong and corrosion resistant. Tin-plate serves a myriad of purposes-the most important being to meet the requirements of the canning industry. Australia's newest steel product, tin-plate, was first produced on a commercial scale during the early part of August, 1957. The commissioning of the Hot Dip Tinning Plant (Fig. 1) of The Broken Hill Proprietary Co. Ltd. at Port Kembla, marked the culmination of a proposal dating back to 1939, the advent of World War II having caused its deferment to the present time.Cornish tin is known to have been exported as early as 300 B.C. to Syria and tinned vessels existed even in the year A.D. 23. The tin coating of plate could be described as an ancient art, believed to have had its origin in Bohemia in the thirteenth century. During the next 450 years, the process spread through Saxony to Pontypool in Monmouthshire, but it was a further half century before any measure of success was obtained.Perhaps the two greatest milestones in tin-plate manufacture were the rolling of iron plates first carried out in 1728, thereby outmoding the hammer formed sheet, and more recently, the development of the electro-deposition process. By the nineteenth century, several important changes had arisen; namely, the substitution of steam for water power, coke for charcoal in the production of the base metal, and...

Jan 1, 1958

By C Young

In the vast expanse of Western Australia’s mining sector, a critical issue has come to light: many mining operations overlook the power of a Broad-Brush Risk Assessment (BBRA) to uncover their critical risks. This oversight has led to a cascade of challenges, where some mining endeavours find themselves grappling with: - Unidentified and unmanaged fatal risks, casting a shadow of uncertainty and heightened compliance risks. - A bewildering landscape where the concept of critical risks remains enigmatic, with some mistaking the risk register for the BBRA. - A fog of confusion surrounding the guardianship of these critical risks, leaving safety responsibilities blurred and undefined. Yet, the solution lies within our grasp. An effective BBRA empowers organisations to: - Pinpoint with unwavering certainty every ‘true’ critical risk. - Clarify ownership for each critical risk, ensuring accountability and swift action. - Create a prioritised roster of critical risks, illuminating the path to safer operations. - Lay the foundation for essential follow-up actions like bow-tie analysis, the identification of critical controls, and the fortification of the safety and health management system. Join us in this presentation, where we delve into the heart of an industry-leading BBRA process. Discover practical insights that will enable your organisation to craft and implement BBRA strategies, bridging the gaps in your journey toward preventing fatalities and fortifying safety protocols.

Apr 16, 2024

By William A. Stickney

The zirconium-hafnium separation plant at Albany, Oreg., was the result of a chain of events that started with studies by A. R. Kaufmann at the Massachusetts Institute of Technology. Variations in the listed neutron-absorption cross-section of zirconium caused him to suspect a misprint. As a result of these discrepancies and following his suggestions, Oak Ridge scientists made studies establishing a value of 0.4 barn or lower. This meant that the potential of zirconium for reactor application was greatly enhanced. Since hafnium is invariably associated with zirconium and has a high neutron cross-section, it was necessary that an efficient hafnium-separation method be developed before the superiority of zirconium as a structural material in nuclear reactors could be realized. The Albany plant was built and operated for the Atomic Energy Commission (AEC) under Letter Agreement AT-(11-1) -140, patterned after a plant operated by the Carbide and Carbon Chemicals Corp. at Oak Ridge, Tenn. Construction was begun in April 1951. Hafnium was to be extracted preferentially as hafnium thiocyanate from an aqueous mixture of zirconyl and hafnyl chlorides in hexone (methyl isobutyl ketone) by a liquid-liquid countercurrent system.

Jan 1, 1959

By J. M. Pilcher

The application of oil to coal for-the reduction of dust has greatly increased the consumers' satisfaction with solid fuels, especially those for domestic use. The combination of oil-treated coal and automatic firing by a small stoker has made possible clean, automatic heating with bituminous coal. This, with the added pressure of competition by other fuels, has caused a rapid development of oil treating practice. A variety of materials derived" from petroleum oils is available from which one may choose for treating a par-ticular coal. Until recently, however, little information had been published to guide the choice. It is most im-portant that the proper type and amount of oil be used in order that all coals marketed as "dustless" will be reason-ably dustless, and thereby maintain a good reputation for oil-treatment. During the past two and one-half years, an investigation of a number of the problems related to the treatment of coal with oil has been conducted at Battelle Memorial Institute. This project was jointly sponsored by Bituminous Coal Research. Inc., Standard Oil Company of New Jersey, Sun Oil Company, and Viking Manufacturing Company. A progress report giving the principal results of the work of the first year was presented before the American Society of Mechanical Engineers in December 1937.1 The present paper is a summary of the entire inves-tigation.

Jan 1, 1939

By Robert Hopler

THE work that is being done by the Government to reduce the dangers of mining was brought out strikingly in the First National Mine-Safety Demonstration which occurred at Pittsburgh, Pa., on October 30th and 31st, under the auspices of the United States Bureau of Mines with the assistance of the American National Red Cross Society and the Pittsburgh Coal Operators’ Association.

Jan 1, 2012

By L. A. Neumeier

Sound experimental ingots of zinc alloys for use as rolling slabs were cast with a specially constructed, semicontinuous casting machine. Nominal alloy compositions of Zn-1.0 percent Cu, Zn-0.12 and 0.36 percent Ti, and Zn-1.0 percent Cu-0.03 to 0.36 percent Ti were cast. This Bureau of Mines study was conducted to evaluate the suitability of the casting procedure for providing stock for rolling into sheet. Microscopic examination of ingot sections revealed structures in which grain size varied from the outer to center ingot zones. Columnar grains present in the center zone of the Zn-1.0 percent Cu ingot were absent in the titanium-containing ingots. The ingots with titanium displayed a finer grain size and eutectic structure in the center ingot zone than in the outer zone; the transition in grain size between the two zones was quite abrupt in some ingots. The overall grain size of the titanium-containing ingots was finer than that of alloys cast by more conventional methods. Chemical analysis revealed that compositional segregation is not a significant factor in the formation of the ingot structure. Microstructural studies of small ingots of similar alloys solidified at slow, fast, and intermediate rates confirmed that the ingot structure in the semicontinuous-cast ingots is related to cooling rate, which is, in turn, related to the particular casting machine design and the influx of cooling water on the withdrawing ingots. Microstructures of thin sheet hot-rolled from slabs of the semicontinuous-cast ingots demonstrated that the ingot structure does not preclude the rolling of sheet having a uniform microstructure. Results of hardness surveys of the semicontinuous-cast ingots demonstrated that copper and titanium exert essentially additive hardening effects in these cast alloys.

Jan 1, 1968

By F. H. Samuel, A. M. Samuel, H. R. Ammar

Casting imperfections, such as porosity, in cast aluminum components greatly influence their fatigue properties. The effect of porosity on the fatigue life of 319-F and A356-T6 aluminum alloys was studied, where the porosity characteristics on the fracture surfaces of fatigue-tested samples were examined using SEM and image analysis. The results show that porosity has the most detrimental effect on the fatigue life: 92 % of all tested samples fractured due to porosity acting as the main crack initiation site. In the absence of casting imperfections, other microstructural aspects such as slip bands can be responsible ( 4 % ). The porosity was investigated in terms of the pore size at the sample fracture surface and its location i.e. near the edge or close to the interior. It was found that porosity located far from the sample surface (edge) has less influence on the fatigue crack initiation, and the fatigue life decreases as the size of the pore located at the sample surface increases. Aluminium

Jan 1, 2006

By A. Takala, B Nielson, J. Schunicht

"Pre-concentration in minerals processing presents clear advantages in energy efficiency, water efficiency, reduction of consumables and minimization of capital and operating costs. Outotec’s sorting solutions are powered by Tomra Sorting in order to achieve pre-concentration of concentrator feed in a variety of mineral processing applications. Sensor based sorting combines advanced sensors with rapid computational evaluation and mechanical separation of valuable material from waste and/or gangue. Modern sensor based sorting machines typically use fine air jets to propel individual rocks, thus optimizing recovery and minimizing “mis-sorting”.Gold is generally present in such low concentrations that sensors suitable for ore sorting cannot directly detect it. Therefore, in order to sort gold ore, properties of associated host rock are used. Free and sulphidic gold is often hosted on the quartz-host rock contact zone. Laser scattering effect can be used to detect the surfaces of quartz and composite quartz-host rock particles for subsequent sorting with very high recovery of 95 to 99%. In addition, ore often preferentially fractures along the quartz-host rock contact zone in the crushing circuit. This behavior helps because it liberates more quartz for detection.The feasibility of sorting is investigated for four gold projects in Northern Europe with similar mineralogy. This includes geometallurgical evaluation, amenability testing, small scale “mini-bulk” factory testing in full scale sensor based sorting. The results of the various tests are presented and basic feasibility demonstrated with information on flow sheet development. In addition, the amenability process is evaluated and recommendations made for future projects."

Jan 1, 2017

By S J. Henderson

Pumped co-disposal of coal processing waste was promoted in the 1990-2000s as a low-cost highperformance alternative to tailings dams. In particular it would avoid high up-front capital for rejects trucks and dam embankments, and would produce a combined waste deposit with better geotechnical properties than either coarse rejects or tailings. Overall, the promise was not delivered; in particular, upon discharge the waste segregated by size, and operators responded by moving the coarser waste to contain the finer waste. In consequence, not only did design analysis lag behind construction, but some of the initial expectations persisted with the result that analyses did not fully represent what was occurring on the ground. After more than twenty years inspecting, designing and tending Co-Disposal Areas (CDAs), it is apparent that they are essentially upstream constructed tailings dams with some more favourable aspects but also a few unique quirks. Although waste management technology has moved on somewhat, the high cost of changing CHPP waste circuits means that most mines with pumped codisposal will continue to discharge mixed waste slurry into CDAs. It is therefore worthwhile to share some lessons in the hope of promoting sounder design, operation and rehabilitation. These include: • Discharged waste does not form a homogeneous wholly competent deposit but instead comprises materials ranging from sandy gravel to silty clay with the distribution determined by movement of the discharge and decant structures; • CDAs circulate and contain a lot of water; • As a result of the first two points, some areas of the CDA comprise saturated fine waste that is no different from tailings and, like tailings, often behaves in an undrained manner; • Seepage is inevitable and desirable because strength improves as water is removed. However, stability is strongly impacted by pore pressures and in design these need to be rationally rather than optimistically considered; • As CDAs are built to about 40m or higher, strength-deformation characteristics of the foundation become more important; • Even if geomechanically stable, CDAs will need covers to prevent salts and acids from reaching the surface; and • Erosional stability of the cover material(s) will probably dictate maximum slopes for rehabilitation.

Jul 1, 2021

By Charles Hart

THE-report of the advisory committee to the U. S. Bureau of Mines, on the use of oxygen in metallurgy, brings to the art of steelmaking a radical change in the method of operation of the many processes of this widely diversified industry. When completed, the improvements suggested by the use of oxygen will be far-reaching and revolutionary. As to its effect upon the iron blast furnace, the use of oxygen should be as important as any of the improvements in the art of iron smelting and should take its place beside the German "Hochofen" which was the first attempt to use a shaft for preheating the stock, and beside the hot-blast stove which heated the blast before entering the furnace. The former initially produced molten iron and the latter made unbelievable economies in fuel consumption. It would seem that a discussion of this paper would be best served by following the conclusions on page 17 of the report and analyzing them seriatim. 1. (a) A decrease in costs, due to higher smelting heats is only attainable by taking full advantage of these heat units. This is affected by, adding additional ore to the burden which in turn increases production and yields a larger tonnage upon which to figure costs. These economies appear in decreased cost per ton of iron for coke and limestone consumed, and a proportionate reduction in all items entering the cost above materials. We can take no exception to these. premises. It is a well-known fact that silicon in the iron and sulfur removed" are the result of hearth temperature, other matters remaining constant. To a practical furnaceman the most satisfactory manner of controlling a furnace is by increasing the burden. It is not necessary, therefore, to consider the question of refractories, for this discussion presupposes that the temperatures in the furnaces will be kept practically where they now stand for making the various grades of iron. The same situation obtains in regard to the height of the furnace, which, as intimated, was one of the great strides forward in this art, and its abandonment at this time, is inconceivable. The shaft prepares the stock so that at each succeeding step we have exactly the proper conditions. All the stock entering the furnace is dried and preheated. The limestone is calcined by sensible heat practically at no cost, for this is sensible heat which otherwise would pass from the top with the gases. Under normal conditions, external calcination has been attempted without tangible results. Under normal average furnace operation, limestone requires about 760 B.t.u. for calcination and the loss of sensible

Jan 11, 1924

By Rachael M. Fischer, Daniel J. Woeste, Terence P. Holman

"A new 50 MW biomass renewable energy power plant was planned for construction in southwestern Georgia. The original foundation design consisted of very conservatively designed H-pile groups with vertical and battered piles to carry the axial and lateral loads. The authors conducted a testing program to value-engineer the foundations with the goals of increasing the working axial pile resistance and reducing or eliminating battered piles. Seven test piles were installed and dynamically monitored with a Pile Driving Analyzer (PDA). Two lateral load tests and one tension load test were conducted. The results of our testing program allowed the project team to: (i) increase working pile resistances by factors of 1.5 to 2, reducing the total number of piles by more than 30%, (ii) eliminate the battered piles, and (iii) lessen overall project risk. Poor communication and documentation in a critical area of the site required some piles to be spliced and re-driven after additional PDA testing, establishment of new driving criteria, and consideration of longterm soil setup. This case study emphasizes the economic and risk reduction benefits of a design phase testing program, and the need for consistent communication between parties in the field.INTRODUCTIONA new 50 MW biomass renewable energy power plant (Plant) was planned and constructed in southwestern Georgia. The Plant converts clean wood-based and paper-based waste from existing forestry and pulp operations, waste timber, and maintenance operations into steam that is used by an adjacent manufacturing facility. The Plant also generates electric power with limited greenhouse or particulate emissions for use by a local utility provider.The project site (Site) is located in Dougherty County, in the Coastal Plain physiographic province of Georgia; an area of known karstic activity. Specifically, the Site is underlain at depths of 30 to 45 ft by the Ocala Formation, a light-colored fossiliferous limestone of the Eocene era. According to Watson (1981), the Ocala Formation is 125 to 200 ft thick in the vicinity of the Site and increases in thickness to the southeast. Due to differential weathering, this formation is characterized by an irregular upper surface that transitions from sandy clay/clayey sand into a dense to very dense silt and fine sand locally referred to as limestone. This subsurface stratum is most relevant to the foundation design of the Plant."

Jan 1, 2016

By S. P. Sandoval

Several researchers have shown that the surface of chalcopyrite becomes hydrophobic under oxidizing conditions. Because dissolution of copper from chalcopyrite in dump leaching occurs under oxidizing conditions, the U.S. Bureau of Mines studied the effect of surfactants on chalcopyrite leaching under dump chemical conditions. Surfactants were selected for study because they can lower interfacial tension. The tests were conducted in shaking water baths using 250-mL Erlenmeyer flasks in statistical experimental design formats. The addition of nonionic surfactants increased copper extraction in the fernc sulfate leaching of chalcopyrite when sufficient Fe3+ was present. A positive interaction between Fe3l+ concentration and surfactant concentration was demonstrated. Copper concentration in the leachhing solutions was increased by as much as 100 pct at 25° and 50° C by adding nonionic surfactants. ionic surfactants decreased leaching. The structure of the nonionic surfactants and their hydrophile-lipophile balance (HLB) influenced surfactant performance. The branched hydrophile of an ethoxypolyol was beneficial to surfactant performance. The ethoxypolyol was the superior surfactant at 25° C, but became unstable at 50° C. Four surfactants, an ethoxyalchohol and three block copolymers, performed best at 50° C.

Jan 1, 1990

By B. Surender Mohan

Mother Earth being a treasure of minerals, it is prime duty of the mankind to preserve this natural source to ensure steady growth of the nation. Utmost care is to be taken to see that these natural resources are explored and exploited scientifically in a sustained manner to ensure that the resource base improves and last longer. In this backdrop, the topic of ?Lignite - its resource and technology options to exploit deep seated deposits? is an apt subject to be deliberated upon in the present context, where the shallow deposits may slowly get dwindled. I shall deliberate upon the resource base of lignite, production profiles of the last five decades, consumption pattern, demand / supply projections, future available technology options to exploit the deep seated deposits, growth trends of the sector etc. in my paper. With the available resource base and future technology options, I can confidentially make a statement that ?lignite will remain as cocontributor along with coal to India?s energy generation and may well maintain its same status in the 21st century too, as it has been in the later part of the twentieth century?.

Aug 1, 2013