Search Documents

This United States Bureau of Mines study is based on a review of U.S. mine fire accidents that occurred from 1970 through 1989. Information on these accidents was obtained through investigative reports written by Mine Safety and Health Administration personnel. For this study, 260 mine fire accident reports were examined. A previous Bureau research effort established that fires causing fatalities were more likely to occur in haulage entries than at any other underground location. This study has found that the most prolific source of haulage entry fires was the inadvertent grounding of trolley wires. The largest segment (15 out of 40 trolley wire fires) resulted from not maintaining adequate clearance between the trolley wire and the vehicle. Several novel fire prevention and control ideas have evolved in response to frequently occurring fire-related problems. These included; discriminating power isolation devices, wire cutting devices, more accessible fire extinguishers, vehicle overcurrent protection, and vehicle fire suppression.

Jan 1, 1994

By T. J. Batchler, K. M. Mohamed, D. F. Gearhart, R. K. Zipf

Seals are explosion-resistant structures built in underground coal mines to isolate abandoned mining areas from the active workings. An equivalent single degree of freedom (SDOF) method such as the single-degree-of-freedom blast effects design spreadsheet (SBEDS) developed by the U.S. Army Corps of Engineers can be used to design seals to resist mine explosions. The critical input for the SDOF code is the seal resistance function. The objective for this study is to develop engineering data for design of plain concrete (PC) and reinforced concrete (RC) seals using finite element (FE) models. The FE models can then be used to generate resistance functions for different PC and RC seal designs, which can be used in the SDOF codes. The U.S. National Institute for Occupational Safety and Health (NIOSH) researchers designed and built a test fixture for use in conjunction with NIOSH’s Mine Roof Simulator to apply a four-point bending load on the face of the tested seal. Eight large-scale experiments for each PC and RC seal were conducted. The experimental design considered the effects of the foundation strength, hitching and roof-to-floor convergence. Calibrated FE models for PC and RC seals were developed using ANSYS Ver. 13. With a very limited number of engineering-based assumptions and a single set of data—including Young’s modulus, compressive strength, stress-strain relationships, etc.—the PC and RC seal models successfully calculated the recorded resistance functions and failure patterns for a wide range of boundary conditions. Plug and RC seals were assumed for a 1.83-m- (6-ft-) high entry to demonstrate the application of the calibrated finite element models for calculating the resistance functions of these seals. The resistance function of a particular plug seal case was found to be a bilinear relationship. The resistance function of a particular RC seal without shear reinforcement was found to be a nonlinear relationship.

Jan 1, 2013

By Michael P. Amsden

"THE ECSTALL CONCENTRATOR is situated adjacent to Highway 101 and the Ontario Northland Railroad, 15 miles east of Timmins, Ontario. Ore is delivered to the concentrator by rail from the mine, which is 17 miles northwest of the plant. Power and fuel are obtained from the hydro and natural gas lines which pass close to the plant site. Water is obtained from the Frederickhouse River, 6 miles east of the concentrator. The main concentrator building is a large structure 500 by 640 feet by 90 feet high and contains facilities for fine crushing, crushed ore storage, grinding, flotation, tin recovery, concentrate handling and reagent handling. Located in the same building are the machine shop, warehouse, metallurgical laboratory, pilot plant, men's change room, sample preparation area and an assay laboratory. The general concentrator layout is shown in Figure 47. Originally designed to handle 9,000 tons per day, the concentrator now treats 10,000 tons per day. Two different ore types are processed by selective flotation in three individual circuits to recover copper, lead and zinc concentrates. In 1973, another circuit was added to recover pyrite and tin concentrates from the combined zinc tailings of the three main circuits."

Jan 1, 1974

By R. R. Brandenthaler

The development of the Seminole area into one of the major oil-producing sections of the country has been accompanied by many innovations and departures from former methods of development. On July 1, 1929, two years and nine months from the date of discovery, 20,490 acres were considered proved, and additional acreage is constantly being developed. Because of its peculiar conditions, extent, and rapid rate of development, the Seminole area provided numerous problems, the solution of which necessitated research in connection with practical field operation; as a result, there was a radical departure from methods usually employed in the development of a new field in the Mid-Continent area.

Jan 1, 1930

By Gordon Clark, Basar Arioglu, Nasri Munfah, Sanja Zlatanic, Tolga Togan

"The 13.2 m (43 ft) external diameter, double deck Istanbul Strait Road Tube Crossing is one of the most challenging underwater tunnel projects in the world. Subjected to 11 bars of hydrostatic pressure, variable geology, and being in a very active seismic area, the execution of the project required innovative solutions, sophisticated construction techniques and prudent risk management approach. The 5 km (3.1 mile) tunnel consists of a 3.4-km (2.2-mile) tunnel boring machine- (TBM) bored tunnel, 1 km (0.62 mile) twin NATM tunnels and cut-and-cover sections. The project is being delivered in a build-operate-transfer (BOT) contract in a public-private partnership. The technical challenges, coupled with financial and commercial risks required the implementation of sophisticated risk management tactics including the provision of independent design verification. The project was opened to traffic on December 20, 2016, four months ahead of schedule.. This article presents the technical challenges of the project from the design, construction, and risk management aspects..Project backgroundThe $1.245 billion Istanbul Strait Road Tunnel Crossing project, dubbed the Eurasia Tunnel, is one of several major infrastructure projects being implemented in the Republic of Turkey in a public-private partnership approach. The project provides a direct and easy connection between the Anatolian (Asian) side of Istanbul and the heart of its historical district on the European side across the Bosphorus Strait which connects the Black Sea with the Sea of Marmara. The project improves connections to a wide network of motorways on both sides, increase capacity across the Bosphorus by 100,000 vehicles a day, reduces congestion and saves motorists an average of 45 minutes of commuting time in each direction bringing significant economic benefits to the city and the region. It eases traffic across the strait, reduces congestion, decreases pollutants and emission while maintaining Bosphorus. It is the most complex part of the project with the greatest challenges and risks. Part 2 is 5.4 km (3.6 miles) long consisting of 3.4 km (2.2 miles) of 13.2 m ( 43.3 ft) external diameter TBM bored tunnel under the Bosphorus Strait, 1-km (0.62-miles) of twin NATM tunnels on the Asian side, cut-and-cover transition boxes in the Asian and the European sides and depressed approaches on both sides. In addition, this segment includes the toll plazas, ventilation buildings, and the tunnel control and maintenance facilities."

Mar 1, 2017

By G Neely

COPING WITH COMPLEXITY In every industry, and mining is no exception, plant and processes increase in complexity over time and managers and operators need correspondingly more knowledge. The mine manager has to delegate details to operators, engineers, metallurgists, accountants, safety specialists, personnel officers and the rest. Is it reasonable then, to expect the Mines Inspector to be competent to judge the conduct of all these operations against the criterion of the regulations? Obviously not, but what are the alternatives? One is a superficial inspection where the inspector goes on a hazard hunt for broken steps and missing handrails. Another is one in which an army of specialist inspectors marches on a mine, sometimes outnumbering the staff. Each is competent to assess some part of the operation and if he or she can find an opposite number among the mine staff, they can discuss details. But what good does it achieve? The system acts to remedy present defects and to make recommendations which, if only they were followed, would prevent the same things happening again. Given that this process has been going on since the first Factory Act of about 1840, how is it that there are any more defects left to put right? The answer of course is that defects keep appearing, and new defects arise as fast as the old ones are found and corrected. Further progress can only be made by preventing defects at their source.

Jan 1, 1994

By G. Stecklein

This report summarizes the results of research into the areas of the fragmentation and entrainment of Airborne Respirable Dust (ARD). The objectives of this program were four-fold: first, to review the present state of knowledge regarding ARD; second, to expand this state of knowledge through the identification of hypothetical microscopic mechanisms by which the coal is fragmented and the dust becomes entrained; third, to specify the informational requirements to verify or nullify these hypotheses; and fourth, to relate experimental techniques that will produce that required information. Additionally, insights are provided regarding potential methods of extraction and/or treatment which may reduce the concentration of ARD.

Jan 1, 1982

By Bob Drew, Goran Vukovic, Bojan Zivanovic, Klaus Gamweger

Reaction bath temperature is a major factor in processing liquid metals and in many applications where a balance between process duration and temperature has to be found to run a procedure efficiently. Also extremes of temperature can decrease the output of a process if too cold or even make it impossible, conversely overheating can be detrimental to both the product and furnace integrity. With the help of the new online temperature measurement system very accurate monitoring of the process is possible in contrast to the current routine practice where the temperature is measured periodically with dip thermocouples. The system works with a digital, fiber optic pyrometer, which is embedded in a refractory housing. Installation in the lining is possible below liquid level as nitrogen is blown to keep the system open and to ensure continuous sight from the optical head of the pyrometer to the molten metal through the tuyere. This permanent temperature measurement gives optimal process control with the potential of taking appropriate actions at an early stage enabling proactive process control. Therefore energy savings and even process endpoint detections can be realized.

Jan 1, 2015

By J. Postle, Deborah McCombe

"This is the third in a series of articles about the Committee for Mineral Reserves International Reporting Standards (CRIRSCO). The first article was an interview with Niall Weatherstone, Chairman of CRIRSCO (CIM Magazine, February 2008) the second described the background and goals of CRIRSCO (CIM Magazine, March/April 2008). In 2007, CRIRSCO was adopted as the Reserves and Resources Task Force of the International Council on Mining and Metals. This decision by ICMM has resulted in an increased level of funding for CRIRSCO and the ability to advance its objectives. In mid-October 2007, CRIRSCO members met in London England to discuss the status of each of the member countries’ reporting codes and the progress of various CRIRSCO projects. Update on national reporting codes Australia: The last update of the Australian JORC Code was in 2004. While there are ongoing discussions about issues that arise from the application of the latest version of the Code, there are no plans to update JORC in the near future. Canada: The Canadian Securities Administrators revised National Instrument 43-101 in December 2005. At the same time, the Canadian Institute of Mining, Metallurgy and Petroleum published updated Resource and Reserve Definitions that are incorporated by reference in NI 43-101. CIM is continuing work on developing Best Practice Guidelines to assist practitioners in the estimation of Mineral Resources and Reserves. South Africa: The South African Mineral Reserve Committee is currently awaiting an update of the Johannesburg Stock Exchange Limited Listing Rules, which will incorporate both SAMREC and SAMVAL (South African valuation guidelines). The official launch of both codes is expected in 2008. Europe: The Pan-European Reserves Reporting Committee expects to release a consultation draft in 2008. Emphasis is being placed on industrial minerals and aggregates, which constitute a very large industry in Europe. Chile: The Chilean Certification Code was approved in early 2008. As part of the Code, a National Commission is being established to screen and review reports on a random or specific basis. United States: The Society of Mining Engineers updated the SME Reporting Guidelines in 2007. The Securities and Exchange Commission has not accepted these more up-to-date definitions and guidelines. The SME committee will continue to discuss the incorporation of these Reporting Guidelines with SEC. SME has also established a class of membership, a Registered Member, which includes disciplinary measures for non-compliance with the SME guidelines."

Jan 1, 2003

By D. Randolph Berry

The U.S. Bureau of Mines awarded a contract to Foster-Miller Associates, Inc. (FMA) to provide recommendations on the safest, most practical methods for complying with new regulations requiring that all underground coal miners have a self-contained, self-rescuer (SCSR) -a device capable of supplying, in an emergency, 1 hr of self-contained oxygen (no breathing of mine air). This report develops information and recommendations which could be used during the early stages of nationwide compliance, especially in the areas of inspection, testing, and underground storage of SCSRs. Volume I contains an Executive Summary, Introduction, Definitions, Recommended Guidelines for District Managers and Mine Operators, and a Storage Plan Checklist and Sample Form.

Jan 1, 1981

By Walter H. Schwedes

Ore grinding mills are really just slowly rotating barrels, but barrels that are growing in size so fast that the application of electric drives for them is rapidly approaching a technology like that for wind tunnels or pumped storage drives. This application is particularly worthy of care because some 40% of the 75 megawatts of power used by a large copper ore concentrator, or some 60% of the 200 megawatts supplied to a large iron ore concentrator, are for grinding. These ore plants are located where the ore is, not where a utility happens to be. So, the challenge is not only to choose a drive and .power transmission for reasonable cost, high performance, reliability and minimum maintenance, but to afford the interface between mill drive and power distribution and source systems to minimize the whole ore plant's monthly power bill, or costs of self generation. Conclusions can be reached in optimizing a drive selection only for each particular ore plant's set of parameters, but by identifying the criteria for selection and then weighting each type of drive per criteria, yardsticks for final choice become apparent. This is the purpose of this paper. Grinding action takes place inside the barrel, where the ore charge is ground with the aid of balls, or mill length rods, or large chunks of ore as in autogenous grinding.

Jan 1, 1972

By G. R. FITT, S. R. B. Cooke, C. W. Davis, V. H. Gottschalk, C. G. Maier, C. E. Wood, R. S. Dean, S. B. THOMAS, John Gross, E. P. Barrett, T. L. Joseph

Lack of funds has prevented publication of much of the metallurgical work of the Bureau of Mines during the past 2 years . The present progress report covers studies in the direct production of iron and steel . The experimental work was carried out in cooperation with the universities of California , Minnesota , and Missouri . Complete reports will be published when funds are available .

May 1, 1934

By Robert F. Chaiken

The U.S. Bureau of Mines conducted an experimental and theoretical study of coupled chemical kinetic and mass transport processes during leaching of pyrite from coal in a counterflow, "trickle-bed" column reactor. Spatial and temporal data on reactant and product concentrations were used as solutions to appropriate continuity equations, which in turn define chemical kinetic reaction rates. Data from four 180-by 30-cm column leaching experiments using coal, coal waste, and air-water and air-FeC13 lixiviants have been analyzed. The rate of leaching was found to be diffusion limited (probably by Fe3+) and not controlled by bacterial action. Rates of pyrite oxidation were found to vary with elapsed time (80 to 225 days) and followed a bell-shaped curve, sometimes with a delay before start of reaction. Maximum rates of reaction ranged from 3 to 10 (mmol/d)/L (column) for coal waste and 0.4 (mmol/d)/L (column) for coal. Reaction was 30 to SO pct complete, probably due to precipitation of product salts (e.g., jarosites), which impede transport of oxidant through the coal. An absorption-desorption model of solids leaching, which considers the role of heterogeneous porosity in solids leaching, was used to describe time-dependent leaching rates.

Jan 1, 2010

By N. Paas

Diesel powered equipment has been operated in underground coal for more than 50 years. According to the Mine Safety and Health Administration (MSHA), there are approximately 3,000 diesel units operating in underground coal mines in the United States. This number is expected to reach 5,000 diesel units in 250 coal mines by the year 2000. Also, there are approximately 5,000 diesel units operating in metal/nonmetal mines such as trona, potash and salt mines: and more than 3,000 diesel units operating in Canada. This increased popularity of diesel powered equipment over trolley wire, electric trailing cable or battery powered equipment is because of improved safety, greater mobility, higher productivity and increased power of diesel equipment.

Jan 1, 1997

By F K. R Klose

Malmberget is a sublevel caving mine owned and operated by Luossavaara-Kiirunavaara Aktiebolag (LKAB), a Swedish state-owned iron ore mining company, in northern Sweden. The mine has an annual iron ore production of approximately 15 Mtpa. The current strategy foresees an expansion which will increase the mine’s depth considerably. Ventilation and air conditioning modelling for the planned expansion is ongoing. One of the most influential parameters for ventilation planning anddesign for a deep mine is geothermal gradient, which is crucial for the design of the refrigeration system. It is determined through virgin rock temperature (VRT) measurements carried out at various depth below the surface. This paper details these measurements and the determination of geothermal gradient for Malmberget Mine for the expansion study, which were necessitated by thelack of information for the focus depth and area.

Oct 12, 2022

Jan 1, 2000

Safe operation and system integrity are two important properties of a mine hoist electrical system. Previous methods used to assess these systems, though rare, have involved extensive downtime and required skilled personnel. The recommended design considerations presented in this report are for a proposed automated system that will perform real time measurements, calculations, and recordings of pertinent performance data. Included are equipment installation and test procedures to be used with the system. The report also contains descriptions of the hoist performance criteria, and how they are to be collected.

Jan 1, 1985

By Nicholas Kyriazi, John P. Shubilla

A joint effort by the U.S. Bureau of Mines (USBM) and the US. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fourth phase of testing from 1989 to 1993. The SCSRYs were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except units with manufacturing defects. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. In addition, some apparatus collected for this study had not been returned to the manufacturer in a recall effort for correction of a manufacturing defect. In both cases, the apparatus would have presented problems in emergency use. Recommendations include improved training in inspection procedures and better enforcement of recall notices.

Jan 1, 1994

By D. Harrington

The primary objective of this paper is to discuss the hazards and furnish a list of recommendations for the safe operation of quarries and related works. They have been compiled from Bureau of Mines publications covering the safety experience of engineers before and during the year in the mineral industry,5 from a publication of the National Safety Council, Inc.,6 from explosives recommendations made by various explosives manufacturers,7 and from suggestions obtained from quarries visited. The second objective is to describe and illustrate safety devices, practices, and quarrying methods. The quarrying and related industries of the United States had a lower accident-frequency rate than either the metal- or coal-mining industry as reported for 1942.8 However, the quarry industry ranked eleventh in 15 major industries during 1942 in lost-time accident fre¬quency; metal mining ranked fourteenth and coal mining fifteenth.

Jan 1, 1950

By Dennis McLaughin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine?s Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested 2nd demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

Jan 1, 1981