Search Documents

By Yanlong Li, Lifeng Zhang, Ying Ren

In this work, a multiphase mathematical model for the fluid flow in argon-stirred steel ladles was established and validated by experimental measurement of wood's metal. Alloy dispersion in the molten steel was calculated. The melting and mixing of alloy was faster with smaller size of the alloy particles, larger superheat and bigger slip velocity. The current mixing time is approximately 300 s with 30 mm alloy diameter and 91.5 K superheat.

Jan 1, 2014

By Karen Talbot, Noah Maier, Rob Jameson, Giuseppe Gaspari

A storage and drainage tunnel advancing below I-75 in Detroit, Michigan experienced sudden subsidence. The Tunnel Boring Machine (TBM) was damaged to the extent that its shield, cutting head and extensive interior components needed to be extracted and replaced along with several completed tunnel segments. The tunnel was 16 feet (4.9m) in diameter with crown over 79 feet (24m) deep at the time. The tunneling contractor immediately engaged their designers and specialty subcontractors to develop a scheme to access the machine and repair the tunnel. They required a shaft 99 feet (30m) deep, with unobstructed plan dimension of 50 feet (15m) to accommodate the large components that needed to be removed and replaced. This precluded the application of an internally braced excavation and instead earth support solutions focused on use of a compression ring. Since the completed tunnel section behind the TBM obstructed closure of the compression ring below its invert, this paper describes the innovative access shaft solution employed. A conventional compression ring was constructed using 5 feet (1.5m) diameter drilled shafts down to the tunnel crown. In front of, and to the sides of the tunnel heading, the secant shafts were extended to over 150 feet (46m) depth, creating a horseshoe of support extending 50 feet (15m) below the planned excavation invert. Larger diameter "King Pile" shafts were drilled immediately to either side of the tunnel, overlapped into each end of the secant "horseshoe". The king pile shafts, together with a heavily reinforced ring beam above the crown elevation, acted as a door frame to transfer hoop loads from the incomplete secant arc into reaction supports above and below the tunnel. These oversize king pile shafts were extended and socketed into rock over 70 feet (21m) below tunnel invert. Very tight installation tolerances were necessary to maintain secant shaft alignment to depths exceeding 150 feet (46m). The project operational, geotechnical, and quality data was managed and visualized using a custom GIS interface. This paper will present the design approach employed and review the construction and quality program selected to repair the tunnel.

Oct 1, 2022

By Luis Toron, Salvador Cortes-Obregon

John D. Price (Colorado Fuel and Iron Corp., Pueblo, Colo)—The paper on the coal fields of the Oaxaca district as prepared by engineers Toron and Cortes-Obregon of the staff of the Bank of Mexico bears witness to the thorough and careful way in which the men associated with this organization perform their work. There is little to be added to their paper in way of discussion other than to confirm and amplify some of their statements. Since the only extensive and well-developed field of coking coal lies in the northeastern section of the country adjacent to Sabinas in the state of Coahuila, it follows that blast furnace plants would be located in that same region. Two such plants are now operating at Monterrey and Monclova, using coke produced at the Sabinas district mines. But the nearer of these two plants is 600 miles from Mexico City and even farther from the center of population. Transportation of products from these mills to the market area is therefore expensive, both because of the distance and the difficulty of the terrain over which it must be carried. The development of an integrated steel industry closer to the center of population has therefore long been a goal toward which the Mexican technicians have been striving. While the presence of coal of some grade has been reported in many of the states, and many ideas have been advanced regarding its possible uses in iron and steel production, deposits of anthracite in Sonora and the various coals of the Oaxaca district as reported on in this paper are the only ones that have been explored in a serious manner. The coking coal from the Mix-tepec zone appears to offer promise of producing a coke which could be used in a standard blast furnace. Several problems are indicated, however: 1—The ash in the coal is high as mined, but indications are that it can be washed to an ash content of 15 pct with a recovery of 70 pct of washed coal. 2—Such washing would increase the volatile content from 17.4 pct to about 20 pct, and in a byproduct oven this should give a coke yield of close to 80 pct with an ash content of coke under 20 pct. 3—A free swelling index of 5 appears low for a good coking coal, and below that of the coals from the Sabinas district, which show between 6 and 9. But washing of the coal should result in an improvement in this regard; in the United States coals from Utah with an index even lower than 5 have made a usable coke. 4—A coal with volatile as low as 17.4 in raw coal and 20 in washed coal would come close to being classed as a low-volatile rather than medium-volatile coal, and low-volatile coals are notorious for their high expansion properties. Several plants in the United States are making coke from straight medium-volatile coal of 26 to 28 volatile content, and one at Rosita,, Mexico, from coal of 25 volatile. But no plants to my knowledge are using coal as low as 20 volatile. Since the Rosita coal appears to be a borderline coal from the angle of its expansion properties the coking of one of the straight lower volatile must be approached with caution. 5—There are few coals possessing any degree of coking properties which cannot be used in coke production by careful attention to its preparation and blending. The fact that coals of other types are available in this same region make improvement through blending very possible. 6—There are other workable methods of reducing iron ore other than the conventional coke-blast-furnace method. These will not be discussed here but it is known that their use has been considered. The technicians of not only Mexico but also of the other Latin American countries are keenly aware of their natural resources and their national needs. This paper emphasizes the fact that the Mexican technicians are working on their problem and attempting to speed the day of self-sufficiency for their country. Salvatore Cortes-Obregon (author's reply)—I wish to thank Mr. Price for his kind remarks. The Mixtepec coal as shown in Table II has 30 pct ash and a free swelling index of 5, but when the same coal is washed to 15 pct ash it has a free swelling index of 8 to 9 and the volatiles increased from 17.4 to 20.7 pct. A satisfactory coke has been produced from blends made in the Mexican laboratory using at least 40 pct of the Mixtepec coking coals with the other Oaxaca non-coking coals. Koppers in Germany report good coke obtained from the Oaxaca coal with a blend of 80 pct Mixtepec coal. Consideration is being given the possibility of using methods other than the conventional blast furnace for the reduction of iron ore near the Oaxaca area; electric furnaces appear promising. The non-coking coals could be used to produce cheap electric energy and the coking coals to make metallurgical coke.

Jan 1, 1955

With commodities suffering dramatically low real prices, mining business margins are under intense scrutiny. Unfortunately, management systems developed early this century for manufacturing are driving counterproductive behaviours that choke productivity. The paper and presentation will explain this and present a proven methodology for increasing productivity. This will be supported by operational examples from Australian and American mining management to demonstrate the importance of modern business performance measurement and analysis systems. It will explain the importance of management systems in driving organisational change to sustain superior productivity and margins. The paper will explain why many executives and managers confuse production (a measure of volume) with productivity (which measures efficiency and effectiveness). It will explain how this and other counterproductive managerial and operator behaviours and attitudes are driven by traditional business management systems exacerbated by managerial and consulting fads. The paper will begin with the simple principle that to improve results one needs to first improve the process producing the result û and will show how this is often violated. Improving productivity then boils down to:accurately identifying opportunities using sound, modern measurement, analysis and reporting systems; methodically improving operating and commercial processes, and changing peopleÆs behaviours and attitudes to sustain changes in practices. The paper will include fundamentals of applying sound measurement and analysis to:processes directly, eg cycle time charts and their impact in cyclical (non-continuous) operations commonly used in rock breakage; drivers of productivity; and process results themselves since correct analysis identifies opportunities accurately. The paper will cover the importance of practical leadership and the need to follow a simple, solid plan for changing systems that drive behaviour. Overall, it will highlight use of modern performance Measurement, Analysis and Reporting systems to drive behaviours and improve margins - without capital investment û and make executive and managerial work easier and more effective.

Jan 1, 1999

By C. Flores

A novel process using solid metals for the direct reduction of more noble metal ions from solvent extraction organics has been developed. Base metals recovery has been the principal focus of investigations to date but feasibility tests have now also been made on galvanically stripping selected precious metals. In this study gold (III) was loaded from an aqueous HAuCI4 .3H20 solution into a mixed organic 40 vol.% TBP, 10 vol. % D2EHPA in kerosene. The direct precipitation of metallic gold from the loaded organic phase using zinc powder and iron, aluminum and copper slabs at 70 °C was successfully demonstrated. The gold reduction rates were relatively fast even though the conductivity of the organic solutions is very low. The reaction rates were studied as a function of the variables zinc particulate size, oxygen and nitrogen atmosphere, water content in the organic phase, organic ratios and temperature. The gold morphology was usually powdery or dendritic in nature but continuous films were obtained in some instances. Activation energies were calculated and possible reaction mechanisms are discussed. In general, the results obtained were very promising and showed that gold can be successfully cemented from selected organic solvents by galvanic stripping using less noble solid metal reductants.

Jan 1, 1995

By Ronald R. Hartman

I can recall a time 10 or 12 years ago when I spent a pleasant Sunday afternoon driving to Jim Thorpe, Pennsylvania to see a carnotite deposit that had recently been discovered. The announcement of the discovery stated that it was in the Pottsville conglomerate in a road cut along the highway. To my surprise, the highway was lined with cars and every weekend prospector for 100 miles had come to see the ?big uranium deposit of the east?. I literally had to stand in line to make a measurement with the scintillation counter I had with me. The thought at first occurred to me that this is evidence of how thoroughly the surface of the United States must have been prospected, more likely, perhaps it points out quite the opposite. A lot of time and energy was being spent in tracing the footsteps of others and a lot of time was spent looking for the obvious occurrences. The point is, that in the early days a tremendous amount of uranium exploration was carried out but few systematic surveys were made. Thorium anomalies were usually discounted after cursory surface field checks. Conversely, in airborne surveys - anomalies due to elevation changes or thin over- burden on hilltops were often investigated more thoroughly than smaller indications on hillsides and valleys. An adequate supply of uranium was nevertheless found due to the ingenuity and persistence of the geological profession and the public in general. This ?adequate? supply, like so many estimates for raw materials turned out to be far too low.

Jan 1, 1967

By Sen S. K, Banerjee D. D, Nandy D. K

It has been stressed that the intrinsic spon- taneous heating characteristics of a coal is not enough in predicting spontaneous fire risk of a mine. The influence of extraneous conditions created from the system of mining operations are also to be reckoned with, A case study was made with a mine in Jharia field, India, being proposed to be developed under short wall method with complete extraction in 4-5 slices followed by stowing.

Jan 1, 1988

By J Nell, J Petersen, X C. Goso

The feasibility of increasing the deportment of titanium species and the stability of the pseudobrookite solid solution (M3O5) in a titaniferous slag was investigated, to facilitate the valourisation of titaniferous slags. Thermochemical simulations using FactSage™ software, ver 8.3 (by Thermofact/CRTC and GTT-Technologies), and equilibration-quench experiments were conducted using an appropriate synthetic titaniferous slag composition in an oxygen partial pressure (pO2) ranging from air to 10-16 atm under non-isothermal conditions. The temperature-pressure phase stability diagram for the synthetic slag containing 37.19 per cent TiO2, 19.69 per cent SiO2, 13.12 per cent Al2O3, 16.00 per cent CaO and 14.00 per cent MgO showed that the spinel solid solution (M3O4) was the primary phase until a pO2 of 10-10.5 atm, thereafter M3O5 was the primary phase until a pO2 10-13.2 atm. M3O4 again was the primary phase between a pO2 10-13.2 and 10-16 atm. The changeover of the primary phase coincided with an increase in the liquidus surface. When cooling the slag in a pO2 of 10-16 atm, M3O5 crystallised as a ternary phase that showed a rapid increase in mass while that of the primary M3O4 phase decreased and that of the secondary perovskite (CaTiO3) phase increased at a slower rate. At 1300°C under sub-liquidus conditions, the contents of M3O5, M3O4 and CaTiO3 were about 20 per cent, 15 per cent, and 11 per cent, respectively. Experimental results showed that the Ti3+/Ti4+ mass ratio in the M3O5 phase, ie a measure of the reduction of titanium species, is not considerably sensitive to equilibration temperature in the reviewed range. Slow cooling and minimum/no oxidation during cooling of titaniferous slag would increase the deportment of titanium species to, and the growth and stability of the M3O5 phase.

Jun 19, 2024

By W. Smith, F. G. Rinker, D. Beggs

Early in 1965 the Surface Combustion Division of the Midland-Ross Corporation was awarded the contract to engineer and construct a taconite pelletizing plant for the National Steel pellet plant, administered by the Hanna Mining Co., near Keewatin, Minn. This plant, which will have an annual capacity of 2,400,000 long tons, will produce pellets from magnetite concentrate using a new process developed through a joint research program by Midland-Ross, Hanna Mining, and the National Steel Corp. The work that culminated in the decision to construct this plant is the result of a research program for the development of the Midland-Ross heat fast process for the production of prereduced or metallized pellets. PELLETIZING PROCESS There are many acceptable methods for producing oxide pellets from ground iron ores and concentrates, and all of these give an acceptable product for blast furnace utilization. The vertical shaft furnace, the traveling grate, and the grate-kiln have been installed in many pelletizing plants in the northern hemisphere; therefore, the acceptance of these methods and the problems associated with them are well understood. However, this research project investigated a method for improving upon these processes to produce a high quality oxide pellet at a low operating cost.

Jan 9, 1966

By J. L. Kearns

The importance of optimizing equipment replacement decisions becomes more critical each year due to the rising costs of buying new equipment versus maintaining old equipment. Replacing equipment when it is physically worn out, or replacing it too soon or too late relative to its Economic Life (when it is economically worn out), is very costly. After extensive literature review and research, Kennecott has developed its Equipment Replacement Guide (ERG) system which identifies, evaluates, and justifies the replacement of uneconomical equipment. The system considers such critical factors as inflation, decreasing work capability, increasing maintenance/repair and operating costs, taxes, time value of money, return on investment, salvage value, and investment tax credit. These factors are used in a system of equations which balance the costs of new equipment against the total operating costs of old equipment. The solution of the equations determines the Economic Life of equipment. Replacement of equipment at the determined Economic Life will earn the specified, required return on investment that is used in the calculation of the Economic Life.

Jan 1, 1979

By Yuzuru Sato

Viscosity has been measured for various molten binary alloys of nickel with iron, cobalt and chromium in order to clarify the behavior of viscous flow of molten nickel alloys. The entire concentration range for iron and cobalt and 0-67at% of chromium content were studied. The measurement method was an oscillating cup viscometry using an alumina crucible that was precisely machined. The temperature was up to about 1880K for all the measurements. The results represented good Arrhenian relationship although some measurements included overcooled temperatures. The isothermal viscosities increased monotonously with an addition of iron and chromium into nickel. The addition of cobalt increased after stationariness. The isothermal viscosities showed concave curves. Activation energies increased monotonously by adding all the elements into nickel. These phenomena were considered to be related to the thermodynamic properties such as the heat of mixing and the structures of mixture melts.

Jan 1, 2003

By Hans Lundberg

Introduction Today, geophysical exploration is recognized as a special science wedged between geology and mining. Universities and technical institutes have special professors teaching geophysics applied to oil and ore prospecting. The list of literature on geophysical exploration has grown from practically nothing at all some twenty-five years ago to ~ several thousands of books, some of them very imposing volumes. Most of the methods now used have been developed since the first World War, and very large systematic exploration campaigns have been carried out in many places, in many countries. It has been rather difficult to obtain enough information as to what is going on in Canada. However, since the Associate Committee on Geodesy and Geophysics of the National Research Council became more actively engaged in promoting geophysical research, it may be easier to obtain information and, in the future, the quarterly issued Canadian Geophysical Bulletin may throw considerable light on the current geophysical activities in Canada. Some twenty crews have been engaged the last few years in geophysical prospecting for ore. In the United States, between 500 and 600 crews are employed exclusively in geophysical prospecting. Most of these, however, are engaged in oil exploration. During the winter 1942-1943, the German Government employed some fifty crews on geophysical exploration, and some ten crews were working for private enterprises.

Jan 1, 1948

By A. W. Hahn

USE of gold leaf goes back to biblical and even to prehistoric times. Both gold and silver, as well as other metals, were employed in illustrating or illuminating manuscripts. The medieval monks also used bronze powders. Metals were subdivided as finely as possible by mechanical methods, or by granulation and then were pounded into finely divided flakes. Substances such as honey have also been employed, since early times to keep the flakes of metal apart during grinding. Stearic acid is a more modern agent used in flaking aluminum and other metals. Finely divided "blue powder" is a by-product in retorting zinc ores, and contains from 78 to 90 per cent of zinc metal. This has been used as a precipitant for precious metals in the cyanide process and for chemical reduction processes. The making of zinc dust by atomizing is a step well known in electrolytic zinc plants. The Thermit process of Goldschmidt also requires the use of finely divided aluminum.

Jan 1, 1937

The paper point out the way whereby the Canadian gobernment regulates and motivates mineral development. In this sense, its important the role of Gobernment policy in the development of the industry to its a stage. The progress of industry is due to a favorauble political climate which created an atmosphere of trust that has atracted foreing investment. Therefore, Canada's position owes much to sound legislation that recognizes the high element of risk in exploration and development and also the exhaustibility of mineral deposits.

Nov 20, 1969

By Michael Hamilton

Mineral resources have been identified at two properties in the Ten takes RARE II area (table 1). Commodities consist of copper and silver. The deposits, in the northwest part of the study area, are hydrothermal and associated with fissure veins that developed along northwest-striking faults within the Precambrian Purcell Lava. In addition to the identified resources, there is high potential for additional copper-silver resources at these properties and moderate potential for copper-silver-lead-zinc-bariun resources at five others (table 2) in the portion of the study area that is underlain by the Purcell. There is no evidence that significant mineralization occurred in strata above or below the Purcell.

Jan 1, 1983

By David Yang

Commercially available flotation technologies for recovery of mineral fines have remained essentially unchanged for several decades. Recent studies have focused simply on improving mechanical and open column cells. Such studies have explored different control strategies and have aimed to improve reagent selectivity, fine air bubble generation and particle-air contact. However, no study has questioned whether current techniques are the most efficient technology for recovering mineral fines. Given that both mechanical and open column cells have a widely accepted carrying capacity limitation, the lack of extensive research into an alternative technology is surprising. Most recently, open column flotation has become an entrenched technology, and it is undermining the efficient recovery of mineral fines worldwide. An alternative exists. Packed column flotation overcomes the above-stated problems as the technology surpasses the carrying capacity limitation of current means by several-fold and almost always achieves the best performance in many comparative pilot tests and full-scale plant operations. Filling a column with packing plates creates a network of sloped walls capable of supporting a froth bed many times deeper than conventional machines. Having froth up to 75 percent of the total column volume tolerates all feed changes encountered in the plant environment and permits maximum flexibility in concentrate quality control. Furthermore, its scale-up is straightforward by increasing column volume or the number of interconnected small cells. As the air breaks upon rising and is distributed horizontally through packing plates, the air spargers can be replaced with a simple blower, resulting in considerable savings in operation and maintenance costs. Packed flotation technology provides a break-through solution for the separation of fine and ultra-fine minerals. Its simplicity, superior performance, and low cost structure make it an appealing alternative to current technologies and allow greater flexibility in downstream processing. Future industrial applications include a wide variety of metallic and non-metallic ores. This paper focuses on some recent scale-up campaigns for nickel and copper sulphide flotation applications compared directly to conventional equipment.

Jan 1, 2014

By R. H. Sprute

The Federal Bureau of Mines conducted full-scale field tests in electro-kinetic dewatering and consolidation of slimes in cooperation with the Hecla Mining Co. at two of the firm's underground mines in north Idaho. To test the technique on new deposits, 4,000 ft3 of slimes from a collection sump, pumped into a watertight stope equipped with electrodes, were treated in two steps. Immediately after placement, direct current was applied using a floating electrode to hasten settlement of suspended fine particles. After removal of clarified water, the residue was further dewatered and hardened with electrokinetic treatment. In 25 hours, the material had become firm and dense with a surface capable of supporting workmen. In testing old deposits, 10,000 ft3 of slimes, placed in an unused tail drift 10 to 12 months previously, were treated. This material was sufficiently consolidated by electrokinetics to allow its removal from the mine with standard ore-handling equipment. In both tests, electrokinetic treatment densified slimes in a relatively short time with moderate power consumption.

Jan 1, 1976

By R. D. Wilson

Ten to twelve million tons of dust is produced by cement kilns annu-ally in the United States, resulting in a serious waste disposal problem. The Bureau of Mines investigated two alkali volatilization methods for converting this dust into materials for making portland cement and a useful potassium product. Portland cement kiln dust was found to be composed of finely ground cement raw materials (CaC03 and 8i02) having a layer of alkali sulfate (K2S04 and Na2S04). In this form, it cannot be directly recycled to cement kilns because concrete is weakened by a reaction between the alkali and the aggregate. Portland cements with 28-day strengths above 5,000 psi were produced from low-alkali residues using sintering and melting methods. For nearly complete removal of alkalies, primarily potassium sulfate, from cement kiln dust, a temperature above 1,300° C and a reducing atmosphere were required.

Jan 1, 1986

By R. K. Collings

"This paper summarizes research that was done at the Mines Branch, Ottawa, to evaluate samples of phosphogypsum for gypsum products manufacture. The samples were from phosphate fertilizer facilities at: Port Maitland, Ontario ; Valleyfield, Quebec; and Fort Saskatchewan and Redwater, Alberta. All samples were wet-screened, washed, filtered and calcined in a laboratory kettle at atmospheric pressure. Tests were also made at higher pressures in a small autoclave. The gypsum and resulting hemi-hydrate, being acidic, were treated before, during and after calcining with various bases. The hemi-hydrate products were checked for time of set, compressive strength and bond to gypsum wallboard paper. The results of this study indicate that phosphogypsum from each of the sources investigated has potential as a substitute for mined gypsum in gypsum products manufacture. Pilot-scale testing is recommended to confirm that the product would be satisfactory for the manufacture of plaster products on a commercial basis."

Jan 1, 1972

By T. J. Ballard

"INTRODUCTION The Buck. Creek corundum area of Clay County, North Carolina, includes one of the largest single masses of peridotite outcrops in the whole Appalachian Range and has been described by Pratt, an early authority on corundum, as offering one of the best potentialities for corundum production in North Carolina.Two principal types of corundum deposits are found at Buck Creek the vein type and the corundum-bearing amphibolite dikes.The vein deposits occur in structural fissures that strike north to northeast in a gangue of feldspar, zoisite, an, chlorite. The corundum is generally coarse-grained and good-quality. The corundum content varies from several percent to 50 percent.The corundum in the amphibolites is more or less disseminated through the dike, is generally lower-grade, and is less in quantity, than the vein corundum. About 50 percent of the amphibolite corundum is coarse enough for snagging-wheel grade but is difficult to separate from the amphibolite.Production from the Buck Creek area has been small and came mainly from high-grade pocket in the vein deposits. Pratt 3/ reports 300 tons of corundum ore was produced to about 1896. No record of subsequent production is available.The critical shortage of corundum during the war, due to transportation difficulties and the depletion of deposits abroad, prompted the Bureau of Mines to investigate domestic reserves.After a favorable report was obtained on the Buck Creek area, the Bureau began exploration of the deposit in September 1943 and continued until February 1945."

Apr 1, 1947