Search Documents

By H. M. Cooper, R. F. Abernethy

Determination of the fusibility of coal ash consists in melting a pyramid of the ash to fluid under prescribed conditions . The conditions of the test are specified by the American Society for Testing Materials4/ and must be adhered to strictly if comparable results are to be obtained . The Society formerly specified a particular type of furnace , but with improvements in design of both electric and gas furnaces , it was decided by the Society to specify only essential details of the test . The Chairman of Committee D - 5 , Coal and Coke , of the American Society for Testing Materials suggested that the Coal Analysis Section of the Bureau of Mines conduct a cooperative investigation on the effect of furnace type and atmosphere upon fusibility of coal ash . The Coal Analysis Section enlisted the aid of a number of laboratories using the more common furnaces to cooperate in the investigation . Four types of gas furnaces burning natural and manufactured gases and two types of electric furnaces with different methods of maintaining a reducing atmosphere were employed . The results from the survey are tabulated herein , and some comparisons are made . There were not enough data from any particular furnace and atmosphere to make a reliable statistical analysis . However , definite tendencies are evident , and attention is called to them by direct comparison. in tables .

Oct 1, 1943

By B. Roy

The Somita plant processes low sulphide gold ore in Burkina Faso with a CIL process. After experiencing recurrent low gold recoveries, Somita undertook an investigation on the source of the problem. COREM conducted a mineralogical study on different pit samples. A series of tests was also conducted on a composite sample from the plant which shows a content of 3.4 g/t in gold and 0.48 % in graphite. A reference test in laboratory resulted in a recovery of gold of 75%, similar to plant recoveries for the evaluated ore. In these tests, even if cyanide is not deficient, it was diverted mainly into iron cyanide complex, copper cyanide complexes and by graphite adsorption. Causes of low recovery were also identified and quantified. Solutions to increase gold recovery were suggested such as increasing gold dissolution kinetics by O2 or by lead nitrate addition, change in activated carbon addition point location to the 1st cyanidation tank and finer grinding to increase liberation. Increase in the pH could also contribute to reduce cyanidation consumption. Following these recommendations, Somita changed carbon addition from tank 2 to tank 1 in the CIL circuit. This change led to an increase of more than 5% in gold recovery. A system for the addition of lead nitrate is also under implementation at the plant and benefit will be evaluated in 2013. Finally, pit management for cyanidation will be done based on mineralogy instead of gold content in the future.

Jan 1, 2014

By J. Perlacia

"As the bulk handling sector continues its transformation to Industry 4.0, the mining industry, and its harsh working and environmental conditions, provides a perfect spot to study the feasibility of remote analysis and maintenance of the components used for bulk handling. The most important and expensive tools have been adapted to the digital era in recent years, from remotely controlled haul trucks to monitored conveyor belts.However, the big items of the installations rely on smaller parts that have been leftaside, mainly due to the difficultyof adapting them to the Internet ofThings (IoT).The paradigmatic example is the lack of monitored rollers, while all the other components of the conveyorbelt installations (the belt itself, motors, drums, etc.) were monitored some time ago. The main problem is that a failure of a single roller can cause the stoppage of the entire conveyor, due to possible damage to the belt. Thus, the implementation of an integral monitoring system of all the components of the conveyor is a must.The research and development department of ULMA Conveyor Components has been working since early 2012 on the development of monitored rollers, testing all the problems until their final installation in different demanding conditions, from the extreme heat in Australia to the freezing cold of Norway. All the tests have been done under actual working conditions, in real installations and have provided valuable knowledge in the identification of problems, their solutions and the final advantages of a roller monitoring system.Background and current stateThe malfunction of a single roller in certain conveyor belts can force the standstill of the entire installation until its replacement, due to the risk of greater and more expensive failures, such as a rip in the belt. In the case of a bulk handling installation, where a continuous supply of material is necessary, an unexpected stop of one hour could result in huge economic losses."

Nov 1, 2019

By R. W. Watson

In January 1980, the Bureau of Mines initiated an experimental program to examine the fire and explosion hazards of one-hour self-contained self rescuers (SSRs). This action was prompted by a growing concern on the part of government and industrial safety officials over the potential hazards of these devices when deployed on a large scale in underground coal mines. Prior evaluation of the safety of these devices had been at best sporadic and usually limited to experimental models. The recent availability of preproduction models of a l-hour SSR fabricated by the Mine Safety Appliance Company* and a production model manufactured by Dragerwerk Ag Lubeck of the Federal Republic of Germany allowed for a more comprehensive and meaningful evaluation of their safety in underground coal mines. This report summarizes the results of a 5-month study of the potential hazards of these two items. During the course of the work, periodic progress reports were presented to officials of the Mine Safety and Health Administration and various mining organizations including the American Mining Congress, Bituminous Coal Operators of America. National Independent Coal Operators Association, and the United Mine Workers of America. The free exchange of ideas that occurred during these meetings had a significant impact on the direction of this study and a serious attempt was made to address all of the issues that were raised at these meetings. The authors are extremely grateful to the individuals that participated in defining the specific problems that could arise as a result of deploying the self-contained self rescuers in an underground coal mine environment.

Jan 1, 1980

By M P. Murphy, C M. D Barton

When developing a new underground mine, the geological interpretation that guides the mineral resource is crucial to the preparation of a reliable ore reserve. In preparing a robust geological model to underpin a resource estimate, practitioners must weigh the comparative risk of accepting a relatively wide-spaced drill hole pattern, versus a more close-spaced pattern that ensures a high local geological confidence for mine planning but may have an exponentially increased time and monetary cost. This paper details the authors’ investigations into the geological uncertainty of IGO’s Odysseus Deposit, which is approximately 645 km north-east of Perth, Western Australia. At Odysseus, the komatiitic nickel sulfide mineralisation is irregularly cross-cut by nickel-barren pegmatites that have intruded and offset its thick ultramafic orebodies. These pegmatites generate significant uncertainty in the precision of Odysseus’ resource volume and tonnage estimates, as well as the subsequent quantification of pegmatite mining dilution in its ore reserve. To quantify the geological uncertainty in the pegmatite interpretations, IGO’s mineral resource practitioners prepared several geological risk studies over the Odysseus North lode, which is the lode most affected by the pegmatites. These studies included categorical conditional simulation of the pegmatites, preparing implicit geological models with alternative algorithms, trialling a machine learning application to prepare a maximum likelihood geological model, and finally assessing the early results of the pre-production close-spaced drilling to these different models. To assess the precision of the different single-outcome models, the authors’ compared the estimated pegmatite content of each model to the range of possibilities modelled by categorical conditional simulation within the planned stopes at Odysseus North. An estimation confidence score for each modelling method was then prepared for each alternative single-outcome modelling method. From these studies IGO concluded that a close-spaced drill pattern is essential at Odysseus, supporting the view of the Competent Person in 2017 who proposed a 25 m drill spacing in areas affected by pegmatite which had been partially classified as Inferred.

May 24, 2023

By P. N. Anyalebechi

"The effects of solidification rate, initial melt hydrogen concentration, and grain refining on porosity formation in aluminum alloy 2024 have been investigated with unidirectionally cooled laboratory-size ingots. The ingots were prepared from melts containing hydrogen concentration of 0.059-0.27 cm3/100 g and solidified at 0.2-37 °C/s. As expected, the amount of porosity, average pore size, and pore number density increased with increase in melt hydrogen concentration and decrease in solidification rate. However, the effect of solidification rate was greater at the very low melt hydrogen concentration (0.059 cm3/100 g). These results are consistent with reported effects of solidification rate and melt hydrogen content on porosity formation in other aluminum alloys. Interestingly, addition of grain refiner slightly increased the amount of porosity and the average pore size, especially at solidification rates above 1°C/s. IntroductionIn shaped castings and wrought products fabricated from ingots, billets, bars, or slabs of aluminum and its alloys porosity formation is a problem. This is because it compromises their tensile strength, fracture toughness, and fatigue properties [ 1-18]. The pores are usually the crack initiation and propagation sites [6,8,9] and the largest pores tend to dictate the fatigue life of the aluminum products [9,10,14]. Porous regions within an aluminum product probably yield first due to the reduced tensile load bearing capacity, causing the concentration of the strain near the voids which subsequently results in premature fracture. In aluminum alloy ingots, billets, bars and slabs porosity formation is particularly problematic because of its persistence through fabrication and potential for reappearance or exacerbation during subsequent thermal treatment processes before and/or after fabrication [19]. In fact, persistence of microporosity is a serious problem in large thick plates of wrought aluminum alloy products that must be rolled from correspondingly large direct-chill or electromagnetic cast ingots. Some of these thick plate products are machined into large aircraft components that are required in service to withstand multi-directional stresses and to possess high fatigue strength, fracture toughness, resistance to stress corrosion cracking, and strength in the short-transverse direction [1,20]."

Jan 1, 2011

By N. A. Gjostein

The real and apparent dependence of the surface self-diffusion coefficient, Ds, of gold on crystallo-graphic orientation has been investigated by isolated scratch smoothing and grain boundary grooving experiments. No systematic variation of Ds with orientation was found along the [100] zone. In view of the experimental scatter in these results, however, only aniso-tropy ratios, p, greater than -1.3 would be detectable. Anomalously low values of Ds were found on the [0ll] and [110] zones when the diffusion direction lies along (the scratch or grain boundary groove is perpendicular to) these zones. By comparing these results with a previous y plot study of gold, it is hypothesized that this is not an intrinsic diffusivity effect, but rather it results from a decreased driving force for mass transfer at orientations where the y-plot curvature is negative and appreciable in magnitude relative to y. The characteristics of this type of anisotropy do not appear sEVERAL investigations1-7 have dealt with the anisotropy of the surface self-diffusion coefficient, Ds, of metals as measured by the decay of single or multiple to be in agreement with the hypothesis of fast diffusion along ledges in the surface structure. In certain cases the Fourier method of determining Ds, described in Paper I of this series9 was compared with the second moment analysis in order to determine whether or not the method of analysis affects the anisotropy ratio. While the type of analysis does influence the magnitude of the anisotropy ratio, this effect is not associated with the shape of the profile, but rather is connected with the iterative volume diffusion correction used in conjunction with the second moment analysis. It is further demonstrated that the volume diffusion correction can be too large by either method when the y-plot curvature effect is large. Certain orientations exhibit an unusual temperature dependence of Ds ; this is discussed in terms of the y-plot curvature effect and/or the influence of impurities on Ds . scratches in the surface. Depending on the system investigated, both large1"3'6'7 and small4'5 anisotropies in Ds have been found. Although adsorbed impurities undoubtedly play an important role in determining the magnitude of the anisotropy,8 there are other factors that can give rise to an apparent anisotropy in Ds, thus obscuring the true nature of an intrinsic anisotropy in

Jan 1, 1968

By H. P. Wang, E. M. Perry

"Analytical solutions for investigating the solidification of casting problems with initial superheat and natural boundary conditions have been derived using an integral method. There are two moving interfaces in the solution field, one for the phase change line and the other for the superheat line. Two coupled nonlinear differential equations, representing two moving layers, were calculated by the Runge-Kutta numerical integration scheme. The solutions are in terms of six dimensionless parameters: phase change number, two Biot numbers for interfaces, diffusivity ratio, and dimensionless superheat temperature and time. Parametric studies on these parameters have been conducted to provide generic information about this phase change problem. This analytical information is extremely useful for validating numerical solutions. A simplified I-D finite element model was constructed for the purpose of comparison. The excellent agreement between the analytical and finite element solutions has proven that they are mutually validated.This validated finite element modeling tool was then used for modeling an investment casting process of a super-alloy with a simple geometry: a two-step plate. The nonlinear latent heat release, a common property of alloy materials, was approximated by several piecewise linear segments. The transient temperature response of this 2-D finite element solution, including a metal/mold gap resistance, shows excellent agreement with experimental data.This fundamental work provides a solid basis for further work on the development of a process modeling tool for the complex investment casting process.IntroductionAt present, the investment casting process is used in a variety of industries. In the aircraft engine industry, in particular, investment casting is used to produce parts ranging from turbine blades to engine frames. Because a large single casting can replace many component parts that require machining, fabrication, and assembly, this one-piece casting approach becomes a very cost-effective manufacturing process.The main constraint in using this process for mass production is the long design-to-production lead time. The standard rigging design is still an art, based on the experience of casting experts, rather than on scientific methods. Many trials are often required before making a sound final casting. In order to .reduce the number of expensive casting trials, the development of computer-aided tooling technology is needed.The fundamental physics describing this manufacturing process can be simply described. They reduce to a solid/liquid phase change problem, with two parts - first, the thermal balance of the initial superheat temperature of the molten metal and the preheat temperature of the ceramic shell through heat conduction, and second, the energy release from the mold surface to the ambient by radiation."

Jan 1, 1986

By L. J. Altenburg

There are a lot of key factors involved in achieving a successful Safety Program. I would like to discuss some of these factors and how they have played a major part in our success at Jacobs Ranch Mine. The areas I will cover concern: 1) Facility Standards (Corporate/Minesite), 2) Communication (Employee/Management -"Teamwork"). 3) Proper Training (Employee/Management). 4) Employee Attitude. 5) Incentive Programs. 6) Health Programs. 7) Results/Benefits.

Jan 1, 1994

By F. P. Haver

The Bureau of Mines is developing a leach-electrolysis procedure to produce Special High Grade (SHG) zinc from sulfide concentrate without the generation of sulfur oxide gases. Chlorine-oxygen leaching of the concentrate yields zinc chloride (ZnCI2) which, after purification, is electrolyzed in a fused-salt cell to obtain molten zinc metal and chlorine gas for recycle. This paper describes a laboratory-scale investigation made to develop a procedure for electrowinning zinc metal from ZnC12. Zinc chloride by itself is not a suitable electrolyte because it fumes badly above its melting point and is a poor conductor of electricity. Other salts therefore must be added to prevent fuming and improve the conductivity. Optimum results were obtained with a KC1-LiCl-ZnCl2 bath at 500° C, using a current density of 5 amp/in2 and an electrode spacing of 0.5 inch. Under these conditions, SHG zinc was produced at a current efficiency of 94.3 pct and an energy requirement of 1.16 kwhr/lb. Fused-salt electrowinning eliminates the need to handle and melt cathodes and increases the production of metal per unit cell volume through the use of higher current densities than are possible with aqueous electrolysis.

Jan 1, 1976

By Philip W. Holland

This U.S. Bureau of Mines (USBM) report describes a chromatographic method that is used for rapid field determinations of carbon dioxide in natural gas streams at a USBM helium production facility. The method employs a commercially available portable gas chromatograph that is equipped with a 10-m fused-silica capillary column coated with a porous polymer. The instrument operating parameters permit determinations to be performed over a concentration range of 10 ppm to 10 pct with a frequency of 20 samples/h. The speed at which determinations can be performed is an important factor when evaluating efficiency or troubleshooting processes at the helium facility.

Jan 1, 1994

By Sydney H. Ball

AMERICAN consumption of industrial diamonds has increased five fold in the past 25 years and today accounts for 15 to 20 percent of the world's sale of rough diamonds. In another decade the value of industrial diamonds sold may well equal or exceed that of gemstones. It is generally understood that industrial diamonds are one of the strategic minerals being stocked by the Government in the present crisis to ensure rapid and efficient armament production. Diamond die making is a trade largely confined to artisans in Switzerland and in certain parts of France. Today, in addition to turning out pilots, we should train expert artisans in diamond die making, for thousands of miles of tremendously small-gauge wire will be needed to make the instruments by which the efficiency and safety of these pilots is assisted.

Jan 1, 1941

By C. A. Rawlins

In an underground mine the ingress of heat can generally be attributed to two sources (Rock exposure and artificial mechanisms). The heat load relating rock exposure is subdivided into stoping [~40%] and haulages [~20%]. Rock is exposed to the ambient air and as a mine increases in depth the VRT (Virgin Rock Temperature) increases which leads to more heat ingress underground. To counter the heat ingress, especially in low-seam stoping areas of a deep level mine, air is, a) cooled artificially, b) the amount of rock exposed is reduced in the back areas of a stope by backfill applications, and c) ventilation air is used more efficiently. The heat reduction within a stope due to placed backfill could amount to ~50% for operations mining at a mean rock breaking depth of about 4500 mbc (metres below collar). Unfortunately, due to backfill transport methods, the physical fluid properties and application methods adopted, additional heat is induced into the air. The heat ingress due to backfill application could amount to as much as 25% of the overall in-stope heat load. This heat influx, seen as a negative aspect of backfill operations, is nevertheless overshadowed by the overall in-mine heat load reduction capability of about 20% attainable. The in-stope benefit [~50%] attainable from backfill operations could be increased with the incorporation of a heat exchange (cooling) methodology to offset the additional heat ingress into the surrounding air of a deep underground mine.

Jan 1, 2003

By S Steffen, S Talu, J Poulsen, G Watt, A van As, J S. Ooi

The economic success of cave mining projects is significantly influenced by the secondary fragmentation size distribution of the caved orebody and making the fragmented ore available for extraction. If the cave does not propagate as predicted, it may lead to stalled cave growth and/or localised preferential caving. This can cause significant ore loss and the inclusion of excessive waste in draw columns, both of which damage the economic value of the project. Uncontrolled caving can have severe consequences for the safety and economics of mines. Such safety risks include air blasts due to the formation of excessive air gaps and damage to infrastructure due to surface subsidence. Monitoring the cave-back delivers critical feedback that is required to exert control over its propagation and reduce the likelihood of adverse consequences. Current methods for monitoring cave propagation include access through open holes, microseismic monitoring systems, time domain reflectometers and extensometers. All of these monitoring systems rely on stable holes for installation and ongoing data collection. However, cables in holes often get sheared due to ground movement in the seismogenic zone well ahead of the cave front, rendering the systems useless. To resolve this issue, Elexon Mining, with the support of Rio Tinto, developed the Networked Smart Marker system, which is based on Elexon’s Smart Marker technology. This system provides a more robust and versatile alternative to other cave monitoring systems as the data is transmitted wirelessly through rock, and thus is not vulnerable to hole shearing/dislocation experienced with current cave monitoring systems. Installations at the Argyle block cave have proven that the Networked Smart Maker system can continue to provide information on the cave-back’s location long after all conventional monitoring systems have failed. This paper summarises the findings from these installations and highlights the benefits for all geotechnical monitoring systems reliant on the stability of drill holes to remain functional.CITATION:Steffen, S, Poulsen, J, Van As, A, Talu, S, Watt, G and Ooi, J S, 2016. Wireless system for monitoring cave-back propagation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 251–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By H. B. FERNALD

THE interesting and carefully developed formula which Professor Bucky presents for answering the question of whether proposed new equipment will give a net return on investment equal to or greater than that on present equipment starts with an assumption that the management may make this relative return a determining factor in its decision whether or not the new equipment should be provided. I do not question that in some cases the management may take this position, but I would point out the error involved in so doing. The proper test is not a comparison of the return on new as compared with the return on old investment, but is rather a comparison of the return on a particular new investment as compared with the return which would be obtainable from some other new investment which now might be made. Then I would point out that I believe Professor Bucky is in error in using as a factor in his computations the item of unamortized cost of old investment. The financial advantage to be derived from a new investment does not depend on the extent to which we may in the past have written off the cost of old equipment, nor does it even depend upon what was the original cost of that old equipment. Even the salvage or resale value of the old equipment will only enter into the picture to the extent that the present salvage or resale value differs from the ultimate salvage or resale value otherwise to be obtained, after due allowance for the interest factor.

Jan 1, 1930

By Nirander M. Safaya

Revegetation success on surface mined lands is dependent upon the nature of the plant growth media. Soil physical and chemical properties dictate the needs for specific reclamation and subsequent management practices. Field experiments were conducted at six coal mine sites in Oliver and Mercer Counties, North Dakota to determine the subsequent effects of a single application of selected amendments on spoil and topsoils over the five year period, 1974-1978. Considerable variations in the physical and chemical properties were found in mine spoils from site to site. The texture of spoils ranged from sandy clay loamy at North Beulah I to loamy at Glenharold, and from sandy loamy at North Beulah 3 and South Beulah sites to loamy sands at the Center site. The pH of the sites ranged from 6.5 at South Beulah to 8.2 at North Beulah 3. In many cases, the pH values of mine spoils were not significantly different from the topsoils. The electrical conductivity (ECe) did not exceed 6 mmhos cm-1 at the test sites even though in other studies much higher values were recorded in the same vicinity. The spoils from Glenharold and North Beulah test sites can be classed as moderately saline, and those from Center and South Beulah as non-saline. The sodium adsorption ratios (SAR) varied from less than 1 to 32, with highest values in the spoils of North Beulah 3 followed by Glenharold; all other sites were nonsodic. Lowest SAR values (less than 1) were found in the topsoiled sites at South Beulah and Center. Spoils of North Beulah 3 test site were highly calcareous, followed by North Beulah 2 and Glenharold. Center mine spoils which were the least calcareous of the test sites, showed the calcium carbonate equivalent three times higher than that of the topsoil. The average calcium concentrations in the spoils of North Beulah 3 and South Beulah test sites were -13 and 14 me 100g -l while at North Beulah 2 and Glenharold test sites 25 and 22 me 100-1-1 were recorded, respectively. The overall magnesium concentrations ranged from an average of 4 to 16 me 100g 1. Sodium concentrations in all sites never exceeded 10 me 100g-1. Phosphorus concentrations on the average at North Beulah 1, North Beulah 2, and Center were 10.2, 4.6, and 22.2 µg g -1 spoil, respectively. Concentrations of potassium ranged from 200 ppm at South Beulah site to more than 375 pp in at the Glenharold site. High concentrations of sulfates (239-2778 µg g-1) seem to contribute to the salinity in these spoils. Chloride concentrations of spoils were low and never exceeded 40 µg g-1 spoil. Based on established critical levels of deficiency for micronutrients in agricultural soils, it seems that none of these were deficient. However, controlled environment experiments did reveal increased plant growth responses when some micronutrients were added to the mine spoils. Treatment effects were highly site specific depending on the nature of the soil/spoil characteristics and, of course, the properties of the various treatments. While slack coal amendment to the spoils at North Beulah 2 site affected significant increases in a large number of variables (both major and trace elements), amendment of the topsoils at the South Beulah test site with leonardite resulted in significant decreases in a number of variables, particularly trace elements. Spoils at Glenharold and North Beulah 3 demonstrated the fewest significant changes due to amendments. Calcium, magnesium, strontium, organic matter and nitrogen were consistently increased from site to site with the addition of lignitic materials. Other spoil/topsoil physical and chemical properties (30 variables) as affected by amendments and time are discussed.

Jan 1, 1982

By Ali Ahmadi, Andreas Rausch, Angela Binder, Stefan von der Mark, Dhananjeyan Jeyaraj, Jana Thomas, Nils Nöther, Stefan Wittek, Thomas Ulrich, Eleni Gerolymatou, Mario Kolling, Helmut Mischo, Michael D. Martin, Tugba Sen, Jens-André Paffenholz, Erik Farys, Oliver Langefeld, Wilfried Ließmann

This paper outlines the MOVIE project, which is dedicated to the development of a digital twin for an underground laboratory at the research and education mine “Forschungs- und Lehrbergwerk Reiche Zeche” in Freiberg (Germany). Data from induced rock deformations and temperature fluctuations is collected using fiber-optic sensors. The objective of the project is to establish a virtual laboratory for real-time analysis of the interactions between geology, geomechanics, geometry and ventilation. This will be achieved by integrating models from these disciplines with artificial intelligence, creating a sophisticated hybrid model. The insights gained will enhance safety and efficiency in mining through improved digital planning options, ultimately contributing to more effective resource management and operational decision-making in different mining environments.

Feb 1, 2025

By A. A. Goss

We investigate the relationship between corporate financial performance (CFP) and environmental and social performance (CSP) in a sample (n=165) of large, publicly traded U.S. mining and oil and gas firms. Using optimally scaled principal components analysis to generate aggregate measures of CSP strengths and concerns, we find higher concerns are related to higher volatility of unexpected earnings and discount rates. Furthermore, these earnings shocks are more likely to be negative as concerns increase. Decomposing this relationship shows that negative environmental performance dominates proactive environmental management as a driver of unexpected earnings, but proactive community efforts increase the magnitude of earnings shocks. We document some evidence of the strategic use of CSR, with those firms that have greater risk investing more proactively in CSR.

Aug 1, 2013

By Harry R. Price, Keith M. Swaffar

The Northeast Raw Water Tunnel transports untreated water to the Detroit Water and Sewerage Department's (DWSD) Northeast Water Plant where it is treated and distributed. The occurrence of a subsidence area which was attributed to the tunnel prompted the DWSD to have the tunnel investigated. After an extensive historical and geotechnical investigation, two access shafts were constructed along the alignment in the vicinity of the subsidence. Following completion of the shafts, the subsidence area was inspected in the wet prior to dewatering the tunnel. Upon the completion of dewatering, a dry inspection was performed. During the dry inspection, an area of significant distress was encountered where sand and silt were boiling into the tunnel along with large volumes of groundwater. This distressed area was located 800m (1/2 mile) north of the original subsidence area. The tunnel was immediately refilled with water and an emergency repair program was planned and implemented. As a result of the distressed nature of the secondary tunnel liner, dewatering of the tunnel could not be performed until the secondary liner and the surrounding soils were stabilized. This paper presents a case history of both the investigation and the repairs of the Northeast Raw Water Tunnel including the various grouting and unique tunnel stabilization methodologies which were utilized.

Jan 1, 1987

By D. A. Meyn, R. L. Holtz, C. S. Pande, M. A. Imam, D. J. Singh

"Various theoretical and experimental techniques used to search and develop new metal hydride systems suitable for hydrogen storage are described. The main theoretical technique under study makes the use of electronic structure of the candidate materials. Microstructural characterization techniques like transmission electron microscopy are being used to study the hydride formation. Novel processing techniques for material preparation such as those needed to produce thin films or amorphous phases are also being utilized. The techniques are illustrated with results from Pd, FeTi and Mg2Ni systems.IntroductionOf the four methods of hydrogen storage, compressed gas, cryogenic liquid, metal hydrides, and gas-solid adsorption, the metal hydride storage method is more attractive from the point of view of high volumetric density and safety. Compressed gas storage has disadvantages of extreme pressure, weight, and volume requirements, whereas storage of hydrogen as cryogenic liquid is unattractive due to the requirements of extremely low temperatures and high consumption of primary energy. Moreover, the number hydrogen atoms present in a volume of 10- 22 Cm3 (nH) in liquid hydrogen state (- 20K) is 4.2 whereas number of hydrogen atoms that can be accommodated in a free volume of 10-22 cm3 of various hydrides are as follows: LiH--5.9, TiH2--9.2, ZrH2--9.2, VH2--l0.2. High hydrogen concentration is usually associated with a large H/Metal atomic ratio but is also a function of structure."

Jan 1, 1994