Search Documents

By Bernard Dallaire, Jean Cayouette, Sylvain Duchesne

"Louvicourt Mine's concentrator, located near Val d'Or, Quebec, treats an average of 4,300 tonnes of ore per day composed mainly of copper, zinc, gold and silver. An analysis of concentrator revenues and metallurgical losses shows a potential for additional gain, particularly in regards to precious metals (kustelite) where recovery is usually around 67 -70 %. The planning, installation and trial operational period of two Outokumpu SK-240 flash cells at the underflow of the primary cyclones took two years. The use of (( flash flotation )) technology has made it possible to exploit the favourable conditions at the underflow of the primary cyclones such as precious metal concentration and the presence of liberated coarse chalcopyrite. These conditions permit early flotation (fresh surfaces) of the kustelite and the liberated copper. Since the start-up of the flash cells, the metallurgical gains have turned out to be very positive with increases in metal recovery reflected in appreciable NSR gains. Also, significant savings in reagent consumption and a coarser copper concentrate have made it possible to reduce the drying cycle of the Larox filter presses since the cells were put into operation.BACKGROUNDLouvicourt Mine is operated by Aur Resources Inc. (30% ownership) on behalf of its partners Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corp. (25%). The mine is located in northwestern Quebec about 600 km north of Montreal and about 25 km east of the mining town of Val d'Or. The mine commenced commercial production in July 1994.The massive sulphide ore deposit lies at depths varying between 450 m and 900 m. Mining reserves (2% Cu equi. cut-off) as of Jan. Is', 2000 are estimated at 7.5 million tonnes of ore averaging 3.4% Cu, 1.8% Zn, 28.0 g/t Ag and 0.9 g/t Au. Delineated ore reserves permit the use of a mechanized transverse blasthole mining method. The extraction order is a typical 1.3.5 mining sequence. Primary and secondary stopes are 15 m wide, 15 to 70 m long (25 m long average) and 30 m high. Backfilling for pillar recovery and regional stability is required."

Jan 1, 2001

By W. G. Hubler

It has been within only the last two or three years that enough progress has been made in preferential flotation to warrant metallurgists in recommending the installation of commercial-sized plants for the treatment of copper-zinc-iron ores. Until the new processes had been worked out successfully, the treatment of this type of ore had proved a stumbling block in the path of metallurgical progress. Separation of lead-zinc ore is comparatively simple. A lead-zinc ore low in iron may be separated and concentrated by gravity con-centration, provided it is not necessary to grind too fine. Owing to the specific gravity of chalcopyrite and sphalerite being so nearly the same, however, their separation by gravity concentration is out of the question. Complex lead-zinc-iron ores in which the several minerals are intimately associated, requiring fine grinding to free them, have been successfully treated by flotation for the past fifteen years. Galena is easily floated, and its flotation, unlike that of chal¬copyrite, is not affected by the reagents used to inhibit the flotation of sphalerite and iron sulphides. When an attempt was made to use the methods of lead-zinc se-paration on copper-zinc ores, it was found that the depressant re-agents added to inhibit the flotation of the iron and zinc minerals would, under certain conditions, depress a large part of the copper. It was also recognized that, in the grinding of copper-zinc ore, soluble salts were generated which were detrimental to flotation unless properly controlled. The main part of this paper will be a discussion of solutions in the grinding circuit in relation to the pro¬duction of soluble salts and their effect on flotation.

Jan 1, 1931

By R G. Moreby, S Bluhm, FávonáGlehn, C Pascoe

Resolution Copper Mine in Arizona, USA, is planned to be a 2000 m deep panel cave mine with virgin rock temperatures exceeding 80¦C in rock with high crystalline silica content, resulting in a very challenging ventilation and cooling system design. This is one of the largest copper orebodies ever found and, with a planned rock production rate of 120 kton/day. The project is currently in its prefeasibility phase and the paper discusses features of the ventilation and cooling system design which includes multiple ventilation shafts with total primary ventilation flow of about 3000 m3/s and both surface and underground refrigeration plants producing more than 140 MW refrigeration capacity. The cooling system features large surface bulk air coolers chilling all downcast air supplemented by an underground secondary air cooler system and a chilled service water system. This will be a very challenging mine to ventilate and cool but this work has demonstrated that it will be technically achievable with the application of existing technology.CITATION:Bluhm, S, Moreby, R G, von Glehn, F and Pascoe, C, 2013. Life-of-mine ventilation and refrigeration planning for Resolution Copper Mine, in Proceedings The Australian Mine Ventilation Conference , pp 125-138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Himanshu Dehra

The pre-fabricated outdoor rooms are often utilised near the mines and construction sites for office purposes. The paper has presented modelling and simulation results of the integration of commercially available glass coated photovoltaic (PV) energy technology and solar ventilation technology into a pre-fabricated outdoor room. The pre-fabricated outdoor room has been setup at Concordia University, Montréal for full scale testing of the glass coated PV modules with solar air ventilation. The computer simulation model has been developed for PV modules installed on a double wall wooden frame in an outdoor room based on its preliminary field testing. The testing apparatus was a wooden frame assembly of double wall with solar air ventilation: two adjacent glass coated PV modules, air column and plywood board filled with polystyrene. The measurement data collected from various sensors were: solar intensity, ambient air temperature, room air temperature, electric power, surface temperatures of PV modules and plywood board, air velocities and air temperatures in the air column. The enhancement in the air velocity of the air column was achieved with an exhaust fan fixed in an outdoor room. The simulation model is used to perform the two dimensional energy analyses with applied one dimensional solution of steady state heat conduction equations. The simulation model is based on conjugate heat exchange paths with network boundary conditions of convection, radiation heat exchange and solar air ventilation heat transport. The model parameters are based on measured values of ambient air temperature, room air temperature, air velocity at outlet of air column in double wall, electric power and available solar intensity. The model has predicted fairly well energy performance of glass coated PV modules with solar air ventilation installed on a wooden frame. The model is also useful for predicting heating, ventilating and air-conditioning (HVAC) requirements for the pre-fabricated outdoor rooms.

May 1, 2007

By L. Escudero-Castejon, S. Sanchez-Segado, A. Jha, Y. Hara, S. Parirenyatwa

Oxidative alkali roasting of chromite is the state-of-the-art process for manufacturing chromium-containing chemicals, which involves dealing with serious environmental problems arising from handling Cr6+-containing wastes generated in this process. In this article a new method for the extraction of Cr2O3 from chromite ores is explained, based on the carbothermic reduction of concentrates in the presence of alkali investigated in the temperature range of 950–1050 °C. Under these conditions, the iron oxides present in the ore body are reduced to metallic iron and the resulting separation of chromium occurs by forming sodium chromite (NaCrO2). The reduced samples are magnetically separated for the recovery of an iron-rich fraction, and a non-magnetic fraction containing NaCrO2, MgO and other impurities. The further treatment of the non-magnetic fraction by leaching yields a Cr2O3-rich product of approximately 85% purity, with remaining alumina, alkali and magnesia. The main advantage of the process is that, under reducing atmosphere and subsequent leaching conditions, the oxidation of Cr3+ to Cr6+ is completely avoided; thereby decreasing the risk of land, air and water pollution.

Mar 1, 2017

By Jimmy Guarnizo

El yacimiento de La Zanja ubicada en el caserío La Zanja, Santa Cruz de Succhabamba, Cajamarca, inició sus actividades de exploración en 1991 y las de producción en el 2010. MLZ construyó el embalse o reservorio llamado Bramadero, que acumula las aguas de escorrentía de la quebrada del mismo nombre durante el periodo de lluvias, las cuales son empleadas para el consumo humano en la unidad minera, y en menor escala durante la época de estiaje para los procesos de operación. En este sentido, el presente texto señala la construcción de la presa Bramadero, la cual genera agua para beneficio de las poblaciones ubicadas aguas abajo de las instalaciones. Asi también cuenta con un programa de monitoreo ambiental para vigilar la calidad y la cantidad de aguas superficiales y subterráneas. Por tal motivo, cuenta con estaciones hidrométricas para evaluar en tiempo real la calidad del agua en los cuerpos receptores del área de influencia de la unidad minera.

Sep 1, 2015

By Gillies A. D S, Lee A. H

Water is an integral component of a mining operation. To-date water management has received a low profile in the overall management of mining operations. To cost effectively meet the requirements of government environmental legislation the man

Jan 1, 1994

By J. A. Morgan, W. A. Barclay, J. C. Pedersen, I. C. Campbell, D. S. Bubar, R. P. Taylor

"Abstract - The Lilypad Lakes property is host to a group of Ta-mineralized dikes that occur over an area of at least 10 km2. Field relationships are consistent with a syn- to late syn-tectonic timing for their emplacement (with respect to the major regional D1 episode of deformation), with several of the dikes exhibiting a steeply dipping, open, S- to M- to Z-shaped fold geometry. Individual dikes range up to 30 m wide (Rubellite Dyke, Pollucite Dyke), have strike lengths of up to 750 m (e.g., JJ Dyke), and are continuous to depths of greater than 250 m (e.g., Rubellite Dyke, Pollucite Dyke). Typically, they display sharp intrusive contacts characterized by the development of thin, holmquistite-rich haloes. The Tamineralized dikes are comprised of silica- and alumina-rich, sodic, granitic pegmatites that display extreme levels of geochemical fractionation (K/Rb typically < 10.0, as low as 2.2; Nb/Ta typically < 0.20, as low as 0.03), and enrichments in an economically important group of lithophile elements, most notably Li, Rb, Cs, and Ta. Geochemical assays of individual surface grab and drill core samples have yielded values as high as 1.51 wt.% Li2O, 1.25 wt.% Rb2O, 6.21 wt.% Cs2O, and 0.108 wt.% Ta2O5. Diamond drilling has established the presence of wide (~20 m), potentially ore-grade intersections of Ta mineralization (>0.045 wt.% Ta2O5) in both the Rubellite and the Pollucite Dykes.Three Ta-oxide minerals (microlite, wodginite, manganotantalite) of primary origin predominate in the Ta-mineralized dikes, where they occur as fine, disseminated grains in the albite-rich pegmatite matrix. The sequence of crystallization is typically manganotantalite wodginite microlite, which conforms to a well-established paragenetic sequence for rare-element granitic pegmatites in general. All three of the primary Ta oxides are characterized by a high degree of chemical purity (e.g., average Ta concentrations in microlite from 77-79 wt.% Ta2O5), a compositional feature consistent with the extreme levels of geochemical fractionation characteristic of the host granitic pegmatites, and one that indicates that the Lilypad Lakes pegmatites are likely to produce Ta mineral concentrates of the very highest quality.Locally, a second generation of Ta minerals is present, restricted to small vugs in the pegmatite matrix that are surrounded by fine aggregates of K-rich mica or clay. The secondary Ta minerals are dominated by microlite, which is typically intergrown with fluorite and Fe-sulphides, and is distinguished from its primary counterpart by its lower Ta content (around 70 wt.% Ta2O5) and much higher concentration of uranium (up to 9 wt.% UO2). Also, secondary microlite consistently yields low analytical totals from electron microprobe analysis, suggesting that it is H2O-rich. The presence of this second, vug-related generation of microlite, together with the occurrence of localized networks of crosscutting fractures that host high concentrations of Cs and Rb (in the minerals pollucite and Rb-Kfeldspar), suggests that a late-stage, fluid-dominated metasomatic/hydrothermal event may have been important in certain sections of the dikes, and has effected a redistribution of the economically important elements Ta and Cs."

Jan 1, 2005

By Andrew Barnes

The adsorption capacity of peat collected from a proposed mine development in northern Sweden has been determined using laboratory column experiments in which peat was irrigated with a simulated (acidic) waste rock dump leachate. The simulated leachate was made using a hydrogen peroxide leach of composite waste rock from the proposed mine development. The waste rock samples were composited in proportion to their predicted extractable tonnage for the mine development in order to generate a more representative leachate solution for the waste rock facility. As expected the test revealed that the peat material shows a very high affinity for attenuation with greater than 70% of Co, 90% of Ni and 95% of Cu removed from influent solutions through the majority of the tests demonstrating the potential benefits in mine water treatment. In contrast, it was found that Fe is initially released from the peat at concentrations up to 100 mg/L and can mean potential problems for the water released depending on the receiving environment. The exact mechanisms for Fe release is uncertain, though it is suspected that ion exchange / competitive desorption is responsible. Inspection of the laboratory results and drainage data from the natural peat wetland receiving drainage during overburden prestriping and mine development at the mine site are comparable, confirm the validity of the experiments, and further emphasize the potential for future use of pre-stripped peat material in managing water quality.

Aug 1, 2013

By Sen-xiang Yang, Xin-teng Liang, Gui-jun Li, Jian-hua Zeng, Yong Chen

"This research is based on PANSTEEL 120t steelmaking converter technology to have the quantitative description of the time needed in uniform mixing of molten steel in the converter with the computer. In present work, the numerical simulation approach is used to analyze oxygen lance nozzle, the flow condition of oxygen and flow status of molten steel in the converter. The various oxygen jet flows that come out from different angles and the flow status of all kinds of jet flows in the converter have also been simulated. All of the simulation parameters are based on the specifically practical conditions according to the physical conditions of PANSTEEL 120 t steelmaking converter. Through numerical simulation, the angle parameter of the oxygen lance nozzle is 16 °. The optimized oxygen lance 536-16 has a good performance in industrial application. This kind of phenomenon shows that the ways and processes of numerical simulation in this research are right.IntroductionThe oxygen lance system is the significant process in semi-steel making converter. It's related to whether the converter or even the whole system can function well. While in actual production, many problems emerge in the process of using the former oxygen lance, such as re-drying, slopping, high lance position, dead burning and even blowing out. In continuous fast-paced process, the unstableness of oxygen lance will lead to speed droop or even stop pouring. Analysis shows that all these problems are not only related to the raw materials but also the design of oxygen lance. Bad oxygen lance's scorification kinetics condition and low content of FeOn in early slag are the direct factors that we cannot easily control in steelmaking at present [l]. Therefore, the good scorification kinetics condition which is related to nozzle has good influence on BOF steel making."

Jan 1, 2013

By A. K. Andersen

One of the prime examples of the versatility of the MARCONAFLO system, which is a body of technology comprising the means to handle, store, load, transport, discharge and reclaim mineral commodities in slurry form, is the direct application of this process to leaching ores. The initial approach was to provide a much improved materials handling system for the transport of copper ores; however, an extensive development program, inclusive of prototype and pilot plant tests, has established that a new leaching concept is possible with this system. Data are presented from the leaching operation of a 25 TPD pilot plant utilizing a copper-oxide ore, mainly chrysocolla. This pilot plant was designed to incorporate true countercurrent flow where the ore is actually in motion, as contrary to vat leaching operations, and the ore being successfully leached is fine crushed ore (3/8-inch x o), contrary to agitation leach circuits. Extractions in excess of 85% of the soluble values are common with only 15 hours of retention time in the MARCONAFLO leaching system.

Jan 1, 1975

By J. M. Stuve

In this Bureau of Mines investigation, the low-temperature heat capacities of polycrystalline phases corresponding to the sulfide compounds CoSO?89&apos; CoS1?33, and CoS2 were measured by adiabatic calorimetry within the nominal temperature range 5 to 300 K. The derived absolute entropies S298 were 10.36±O.02, 12.96±O.03, and 16.31±O.03 cal?mol-1?K-l, respectively, assuming third-law behavior. In addition, the standard enthalpy of formation 8Hf298 of CoSO?89 was determined by bromine solution calorimetry. The derived value of 8Hf298 was -50.63±2.1 kcal?mol-1, based on the 8Hf298 of Co0. This result is considerably more negative than previously published formation values based on high-temperature gas equilibrium studies.

Jan 1, 1985

By J. L. Reuss

The Bureau of Mines derived information on the softening characteristics of both unfired and indurated iron ore pellets as measured by hot compression strength in a laboratory study. A surprisingly high hot strength (240 1b per ½ -inch spheroid) was developed by unfired magnetite pellets near 900° C; lesser maxima were developed by pellets made from hematite and specularite concentrates near 1,000° C. Those from goethite remained weak throughout the pre induration heating. Fully indurated commercial pellets retain a high resistance to softening when heated in air. On the contrary, in a hot reduing atmosphere their high cold crushing strength dissipates rapidly. At 1,000° C, for example, the average compression strength of seven different commercial pellets was 110 lb; at 1,100° C, the hot strength was only 60 lb. After a rather sharp initial drop, the loss of strength with increase of temperature was gradual. There was no sudden collapse, nor any significant difference, in behavior of commercial pellets whether made from magnetite or hematite concentrates.

Jan 1, 1968

By N. B. Pundari

Proper selection of large walking draglines, based on sound engineering principles and field experience, has not kept pace with the large capital expenditures needed to buy these stripping machines. The use of large walking draglines for stripping overburden in US surface coal mines grows steadily, but equipment selection continues to pose problems. An improper size, model, make, or spoil reach selected for a particular stripping application results in additional, unnecessary coal production costs. Large walking draglines are being used to dig deeper tar sands at the Syncrude operations near Fort McMurray in Northern Alberta, Canada. This application is compared with typical deep digging operations and dragline use prevalent at typical US strip mines.

Jan 4, 1981

By Robert H. Merrill

In 1960, the Kennecott Copper Corp. and the U.S. Bureau of Mines entered into a joint research program to determine the changes in stress, strain, and displacement created by changes in slope angles. The field site was the Kimbley Pit, located near Ely, Nevada; the supporting laboratory investigations were made at the Bureau&apos;s Denver Mining Research Center. Following a study to determine the rock stresses in the mining district, the strike and dip of geologic defects (fractures) in the rock, and the laboratory-determined strength of the rock, a new slope angle and pit configuration was selected, and instruments were installed to measure changes in stress, strain, displacement, microseismic noise rate, and sonic velocities at several points in the west wall of the pit. Between February and November 1966, the west slope was changed from an average angle of 45° to a new slope angle that started at 45° on the south wall, gradually increased to 57 ½ at the center of the west wall, and to 61° on the north wall. The pit was deepened from about 500 feet to about 550 feet. About 2.55 million tons of waste and ore were removed by stripping and mining.

Jan 1, 1968

By Li Qihou, Li Yuhu, Liu Zhihong, Liu Zhiyong, Yang Xiaofeng

Scorodite samples were synthesized, in adding or without crystal seed respectively by using Atmospheric Scorodite Process (ASP), Hydrothermal Scorodite Process (HSP), and Improved Atmospheric Scorodite Process (IASP) individually; and their crystal structure, crystallinity, morphology, particle size, specific surface area, Fe/As mole ratio, as well as the leaching stability were characterized, aimed to reveal the relationships among the synthesis methods, the compositional and structural properties, and the leaching stabilities of scorodite. The results show that synthesis methods have significant effects on the compositional and structural properties of scorodite. Scorodite samples of high crystallinity, small specific surface area, and low Fe/As mole ratio, possess high leaching stability. The order in the leaching stability of scorodite samples synthesized in this study is as follow: ASP<HSP<IASP. Scorodite particles in the sample synthesized by IASP without crystal seed are in large sizes and of pyramidal morphology enclosed mainly by crystal planes of {111}; and the sample possesses the crystallinity of 84.5%, the particle size (D50) of 28.2 m, the BET specific surface area of 3.72 m2/g, and the Fe/As mole ratio of 1.05; after leaching this sample by using acetate buffer solution of pH 4.95 for 10 days, the total arsenic concentration in the leaching solution is merely 1.14 mg/L.

Jan 1, 2015

By Thomas J. Blalock

The volumetric determination of uranium according to the method of Sill and Peterson (6),3/ which uses cerate oxidimetry after the separation of interferences such as sulfides and cupferrates, has been used for some time by the Bureau of Mines and gives satisfactory results for many of the samples tested. However, in those instances where the uranium content did not exceed a few tenths of 1 percent and iron was present in the range of 10 to 40 percent (as Fe203),4/ the method was cumbersome and unreliable. The need for a more accurate procedure for the determination of small amounts of uranium in the presence of large amounts of iron, such as in shale or black sands, prompted this investigation. The Bureau desired that materials containing as little as 60 p.p.m. of uranium be assayed within reasonable limits of accuracy. One of the primary aims of this work has been to eliminate, as far as possible, the necessity for repeated cup ferron extractions.

Jan 1, 1960

By W. W. Rudolph, L. N. Trevani, P. R. Tremaine

UV-visible spectroscopy, Raman spectroscopy, and vibrating tube densimetry have been used in our laboratory to determine equilibrium constants of aqueous species at temperatures as high as 325 °C. The UV-visible and Raman spectra of solutions containing metal complexes and ionized acids or bases can be used to yield formation constants by applying curve fitting methods to resolve the contribution of each species. Colorimetric pH indicators identified by Johnston and coworkers at the University of Texas (Austin) provide an alternative means of determining ionization constants and the pH of complex mixtures. High precision density measurements over the same range yield standard partial molar volumes, which are key parameters for "equations of state" for aqueous species. Examples are given for the copper-ammonia system, simple carboxylic acids, and the iron-sulphate system.

Jan 1, 2004

By Charles Dumaresq

The management of mine tailings poses a complex range of potential risks, including physical risks, such as the risk of catastrophic failure of a tailings facility and chemical risks such as the risk of long-term leaching of contaminants into the downstream environment. If these risks materialize, they can lead to a wide range of impacts on people and the environment, including human fatalities and severe impacts on downstream ecosystems, and the costs of recovery borne by industry, communities, governments, and society as a whole can be immense. Tailings facility failures in Canada (2014), Brazil (2015 and 2019), South Africa (2022), and in other locations around the world underscore how high the stakes are when mines produce and manage tailings (WISE Uranium Project 2019). Understandably, many people do not trust the mining industry to manage tailings responsibly. As an industry, it is our responsibility to manage tailings in a manner that is responsible and strives to minimize harm associated with tailings management, including effectively managing both the physical and chemical risks associated with tailings. Standards have an important role to play in responsible tailings management by setting expectations for standards of care and providing a means to measure and report on performance. In jurisdictions with strong legal requirements for tailings management, standards play a complementary role, pushing performance improvements in areas that may be difficult or impossible to address in legal requirements. In jurisdictions where legal requirements are lagging, standards may represent the de facto leading practice and may be the primary tool to help ensure responsible tailings management. Implementation of standards can help companies demonstrate that tailings are being responsibly managed and help build trust and credibility. Most importantly though, standards are important tools to help ensure that the risks associated with tailings are reduced, and that remaining risks are effectively managed. However, we must recognize that conformance with standards can have a down-side – the proverbial two-edged sword. Having standards is vital but there is a risk that implementing standards becomes a “box checking” exercise, with ongoing conformance leading to complacency. We must not allow ourselves to fall into the trap of believing that, just because we are complying with applicable standards and laws, we are therefore doing our best, and that “it can’t happen to us.” In addition, if conformance becomes the goal and the standard does not have mechanisms to drive continual improvement, then once the standard is met, there may be no incentive to improve. The point of complying with standards is not to pass the test. The point is to manage tailings responsibly, prevent catastrophic failures, and minimize harm. The point is to do better, because we must do better. To do that, we need to strive not for conformance, but for excellence in tailings management, driven by continual improvement and a quest to do better.

Feb 1, 2025

By L. Forbes, G. Forbes, J. Wang

Bubble size measurement is a vital part of flotation system analysis and diagnostics. Over the years, a great many different bubble size analysis tools have been developed. However, all of them rely on ex-situ measurement and in-pulp sampling techniques. This paper evaluates the Mettler Toledo ParticleView™ Measurement probe as a novel method for in-situ bubble size measurement. This device is then compared to the conventional Anglo Platinum Bubble Sizer (StoneThree). It was found that the in-situ bubble size analysis technology appears to be a more user-friendly and reliable option for determining bubble size in flotation. However, the current instrument design is not suited to industrial applications. Keywords: Bubble size measurement, bubble coalescence, PVM probe

Jan 1, 2020