Search Documents

By Christopher J. Brown

"Proper ground stability in gate roads has been a critical aspect of success in longwall mining. In particular, the tailgate has proven to be one of the more active mine areas that needs to be managed (Barczak, Dolinar, and Mucho, 1999). As longwall tailgate support technologies continue to be developed and improved, Strata Worldwide has worked to design and manufacture a revised Propsetter to provide additional support capacity and enable applications at greater mine heights. The support is targeted for tailgate applications; however, it can also be used for roof support in various types of mining environments. This paper describes the design changes for enhancing the support capacity of the Propsetter to more closely align its performance with other support technologies currently being employed in longwall tailgates. Balancing changes to each design aspect of the Propsetter was key to successfully improving the roof support load capacity while maintaining controlled deformation. Increasing the load capacity would allow a mine to improve support efficiency with a smaller, less intrusive support compared to support alternatives and to reduce the cost per foot of supported entry. The target support capacity was 80 to 100 tons at two inches of deformation to more closely match the performance of competing tailgate supports, such as the 24-inch-diameter CAN®. To achieve this goal, changes were made to all design aspects of the Propsetter: diameter, wedge cut depth and angle, pod size, and confinement rings. Test results from the NIOSH Mine Roof Simulator verified that these design changes were successful in increasing the capacity of the Propsetter to the 80- to 100-ton range at two inches of deformation. INTRODUCTION Roof support is one of the most fundamental elements of the underground mining process. As materials are removed from the earth, geological conditions will almost always require some form of roof support to keep the extraction area open and stable. Coal mining environments often experience difficult geological conditions that require both primary and secondary forms of roof support to keep the mining environment safe and economical. The secondary support system serves as additional support in the case the primary support system is inadequate. If designed properly, the secondary support system will also assist in maintaining integrity of the immediate roof beam (Barczak, 2000)."

Jan 1, 2017

By Eddy Dénommé, Deni Villeneuve

"Niobec mine, a producer of pyrochlore concentrates since 1976, became a producer of ferroniobium in 1994 and achieved accreditation to the ISO 9002 standard in 1995. The goal of ISO 9002 is to ensure that the products supplied to clients regularly meet their specifications, through explicit work standards and procedures throughout the production process, from deposit appraisal to ferroniobium production.A key element of ISO 9002 implementation at Niobec consists of the quality control procedures applied to the raw materials: the ore fed to the mill and the pyrochlore concentrate fed to the reduction plant. These controls extend from exploration, deposit appraisal, mine planning and reserves estimation, mining, mineral processing and, finally, ferroniobium production. The implementation of ISO 9002 has allowed more efficient control of the quality of the final product sold to clients. It requires interactive team work, the role of the geologist being to relate all information pertaining to raw material and product quality to the geological framework of the deposits."

Jan 1, 1997

By Lewis Carroll

AS he contemplates the numerous good things the hard-working committees have evolved for the 140th Meeting of the Institute, the Editor knows just how the walrus felt when he uttered his memorable, if somewhat lugubrious lines. For there are the Annual Reception and Dinner at the Commodore, 'the Gold Supply Symposium, the luncheons, general and special, and the Annual Institute of Metals Lecture, a Round Table on Iron Ore and a wonderful Informal Dance at the Grand Central Art, Gallery, substantial general sessions, a Smoker-and many other things. -Old, friends and new, reminiscences and confidential chats, horizons pushed back by new information and adjusted perspectives, courage revived and ambitions stimulated-one with a flair for the modernistic might make something-or nothing-of the kaleidoscopic preview 'of the coming Annual Meeting.

Jan 1, 1931

By Jennifer L. Bell, PATRICK L. YORIO, Emily J. Haas, Susan M. Moore, Lee A. Greenawald

Although researchers have struggled to replicate Heinrich’s safety triangle findings (Heinrich 1931) for various reasons (e.g., no access to his original database and it is unclear if the database was of a single establishment/operation or for an entire industry), the occupational safety community has continued to adopt and expand the applications of this theory (e.g., McSween 2003). Within the mining industry, the potential exists for operations and companies to use concepts from the safety triangle as a way to inform or challenge the practices employed within their health and safety management systems (HSMS) to prevent incidents (Backlund 2016). This paper considers data obtained from the Mine Safety and Health Administration’s databases and demonstrates the validity of applying the safety triangle theory at the mine level. The results support the use of this theory and demonstrate that lower severity incidents can predict fatalities in a subsequent year where significant nuances and caveats to applying the theory are identified and discussed.

Jul 25, 2020

By Pat McCarran

WHEN this Government was founded, the framers of the Constitution wrote into that instrument a provision that Congress should "coin money and fix the value thereof;" and the Constitution prohibits making anything but "gold and silver" lawful money. So silver is written into our basic law. Shortly after President Washington took office in 1789 the Congress passed the first Mint Act, setting up the U. S. Mint. In that Act, signed by President Washington on April 2, 1792, the weight of the American dollar was fixed, and it was provided how much silver should be contained in a silver dollar and how much gold should be contained in a gold dollar. It was decided that 371 1/4 grains of pure silver was to be the standard dollar of America. That standard with respect to the pure silver content of the dollar has never changed.

Jan 1, 1947

By Huang Daguang, Paulo Couceiro, Juan Navarro

Mining is typically conducted through a set of interdependent unit-operations, which commonly include drilling, blasting, digging and hauling, in order to deliver the required ore material into the comminution circuit and to remove waste rock with minimum impact in the operation. In such complex environment, the identification of critical paths, and respective interfaces between different unit-operations, are necessary to determine a sustainable long-term operational program. Facing this challenge, adaptive cost optimization strategies are required to increase productivity and revenue while minimizing potential environmental impacts. Since the overall mining efficiency can be strongly impacted by blasting outcomes, an operating method based on the searching of the ideal blast design is required in order to minimize the mine total cost of ownership. The implementation of a consistent continuous improvement program requires specific care in terms of design, control and execution of the different stages of blasting. For that, the application of the most advanced technologies for rock characterization, based on drill monitoring systems, and smart explosive products, allows the improvement and control of blast results by adapting the explosive energy distribution to the rock condition, so as to optimize the performance of downstream stages such as digging, hauling and comminution. This paper describes the application of a heuristic optimization approach, where blast parameters are used as decision variables to evaluate the potential impact of several blasting scenarios on subsequent unit operations, under the continuous ability of modelling, measuring and calibrating operational performances along of the mine cycle.

Feb 6, 2023

By Anthony Konya, Calvin J. Konya

This paper will present this research which correlates the borehole pressure to variables such as the Young's Modulus and Tensile Strength of various rock types giving blast designers the ability to design a presplit to function in many rock conditions, including weak rocks such as siltstones and mudstones.

Feb 1, 2020

By Dr. Paul Worsey, Dr. Calvin Konya, Dr. Anthony Konya

Development of methods to calculate presplit blasthole pressures through simplified models, namely the Empirical Model and the Detonation Pressure Model. These models can be used with variations in explosive type and diameter, along with borehole diameter. All models have been validated with test data and shown to have minimal error.

Feb 1, 2020

Controlled blasting experiments in small development drifts were conducted at CANMET's Experimental Mine, from August 1992 to November 1993. The objective of these experiments was to develop suitable controlled blasting techniques for small development headings drilled by jackleg with 32 mm diameter holes. The experimentation also aimed to provide insight into blast damage mechanisms. Particular attention was given to the physical-mechanical properties of the rock and the rockmass structural data in order to make the results applicable to other geological environments. The drift faces were approximately 2.4 m by 2.4 m with 36 to 43 holes drilled to a depth of 2.4 m. Cartridged water gels, emulsions and semigelatin dynamite were used in the cuts and as primers, ANFO as the main explosive and decoupled 19 mm diameter semigelatin dynamite charges were used in the perimeter holes. Smooth blasting techniques and pre-splitting were tested in the underground mine. All the blasts were monitored with a multi-channel blast vibration monitor to which was attached sets of high frequency geophones and accelerometers. This first set of experiments has illustrated the efficiency of con-trolled blasting techniques to reduce blast damage and demonstrated the need for further research to improve the safe and efficient use of explosives.

Jan 1, 1995

By M. J. Shulman

The exploration geologist is frequently confronted with the problem of allocating his resources, i.e., exploration effort, among various areas. Although geologic, financial and logistic considerations influence the allocations, no objective criterion is usually given which determines the optimal allocation. Maximizing the gain in information, subject to the constraint of a limited exploration budget, is used as the objective criterion to allocate reconnaissance effort. The information function, I(x), quantifies the expected gain in information, where x is the scale of exploration. To calculate the information function the following data are necessary: 1. The probability that an area contains a target must be estimated. 2. For each scale of exploration, four probabilities must be estimated: the probability that an anomaly is produced by the target; the probability that an anomaly is not produced by the target; the probability that an anomaly is produced by a barren area (false signal); and the probability that an anomaly is not produced by a barren area. Alternatively, the barren area can be replaced by other targets. To illustrate the allocation model, the optimal number of line kilometers/line spacing per area is determined for an aeromagnetic survey for iron in Egypt.

Jan 1, 1985

By Stephan A. Jefferis, Adrian H. Bath

"This paper draws together some themes on the durability of barrier systems, and particularly cementitious systems. For contaminated land and water retaining structures, durability can be poorly addressed at all stages of a project, from specification, to barrier material selection, barrier design including toe-in and through to performance assessment in operation. Permeability (hydraulic conductivity) is a dynamic property which will vary over time as reaction processes propagate through a barrier. However, laboratory testing, when undertaken, tends to be focused on short term tests with aggressive chemicals so that the effects of longer-term processes such as carbonation and leaching by permeating water are missed. For water retaining structures, carbonation and leaching actually may be the most significant processes affecting barrier performance as the groundwater adjacent to many water bodies can be otherwise rather benign (as regards bentonite and cementitious systems). These and other reaction processes have been modelled in the arena of nuclear waste repositories and procedures are well recognised. However, such procedures have yet to be widely adopted for the assessment of other barrier systems.INTRODUCTIONOver the last few decades there has been an enormous amount of laboratory research on the durability of barrier materials or more specifically papers reporting the results of permeability tests. Unfortunately there is a much smaller literature on scaling test results to barrier dimensions in the field or to required design lives. Although in the geotechnical industry durability research has been largely laboratory based, in the nuclear industry where relevant timescales are multi-millennia rather than decades, research has been heavily underpinned by geochemical modelling. A significant purpose of this paper is to examine the tools that may be used to analyse the results of tests on barrier materials used in geotechnical engineering, for example, for water retaining structures and contaminated land and draw the attention of the construction industry to the potential of the modelling procedures developed for nuclear repository assessments. Modelling can help to identify underlying processes and so augment information from laboratory testing focused on changes of physical properties such as permeability and strength."

Jan 1, 2016

By J. W. van der Merwe

Technology is advancing at a rate that makes it extremely difficult for the mining Industry to keep pace. Many advances occur within a given piece of technology and often this is missed by the disciplines that could have gained advantage by its implementation. Often this may have been simply an aspect of cost exceeding benefit. However, there are some technologies that potentially have such a far-reaching impact on the mining industry that the benefits simply outweigh the cost. The application of 3D laser scanning in the mining industry has the potential of taking the concept of ?Google maps?? underground. This presents an opportunity where the virtual world of underground can be traversed with relative ease and many aspects of measurements could be obtained without having to visit the working place again, potentially saving countless man-hours and still delivering precision work with significant savings in downtime, stoppages, and exposure to safety incidents. Anglo American Platinum maintains its competitive advantage though the review and application of appropriate technology. This paper describes the 3D laser scanning trial at one of Anglo American Platinum?s new shafts, and goes on to show the benefits encountered through the application and the involvement of the various MRM disciplines.

Jan 1, 2012

By Mark R. Svinkin

"Construction equipment and operations usually produce soil and structural vibrations which may harmfully affect various structures and also the content of buildings and houses. The level of structural vibrations depends on a number of factors such as characterized sources of vibrations, soil conditions, and susceptibility of structures. There are certain knowledge and experience for managing the effects of construction vibrations which require implementation of condition survey of structures, information on construction dynamic sources and soil conditions at a site, evaluation of possible vibration effects on structure, calculation of ground vibrations before construction, use mitigation measures to decrease vibrations, and a choice of appropriate vibration limits. The paper presents the application of known concepts for assessment of vibration effects on structures from bridge constructions.INTRODUCTIONVibrations producing by construction activities such as pile driving, dynamic compaction of loose soils, demolition work, heavy construction equipment and trucks can affect adjacent and remote structures. Vibration effects on structures, sensitive devices and processes may create significant practical problems. Legal actions are often required for solutions of vibration consequences. The level of construction vibrations depends on dynamic sources, soil conditions at a site in particularly availability of soils with settlement potential, distances from the sources, parameters of waves propagating at a site and susceptibility rating of adjacent and remote structures. It is likely that intolerable structural vibrations from direct vibration effects of impact pile driving and resonant floor vibrations from vibratory pile driving may be induced in adjacent structures to construction sites.Foundation settlements resulting from soil vibrations in loose soils usually occur in the proximity of dynamic sources, but it is important that dynamic settlement may happen at various distances from the source. There are such examples. First, Kaminetzky (1991) mentioned a case history of building settlements developed at a distance of about 305 m (1000 ft) away from a pile driving site. Foundations of the buildings were underpinned on piles down to the tip elevation of the new driven piles to prevent building settlements. Second, Lacy and Gould (1985) shows that the peak particle velocity (PPV) of 2.5 mm/s (0.1 in/s) of ground vibrations could trigger dynamic settlements at distances up to 30.5 m (100 ft) from driven piles."

Jan 1, 2016

By AIME AIME

THE Tuesday afternoon session", H. A. Bedworth chairman and T. S. Fuller, vice-chairman, was opened with D. J. McAdam, Jr.'s paper entitled "The Influence of Cyclic Stress on Corrosion." This paper dealt with the influence of cyclic stress on corrosion of alloy steels, corrosion-resisting steels, monel metal and aluminum alloys. The paper was discussed by T. S. Fuller, who pointed out that steels under stress corroded more than unstressed steels when subjected to steam.

Jan 1, 1930

By J. J. Jakosky

THE method of electrical mapping of oil structures to be described possesses certain limitations, as well as certain definite advantages. It, in common with other geophysical methods, is not a panacea for the solution of all subsurface geological problems. It operates on differences in electrical conductivity of the geological strata, whereas the other most-used methods operate on (1) differences in magnetic properties, (2) differences in gravimetric properties, or (3) differences in seismic properties. This modification of the resistivity method is therefore able to obtain subsurface information under conditions not favorable to the other methods mentioned. Where the other methods have been employed with ambiguous results it may act as a complementary method.

Jan 1, 1936

By C. K. Leith

THE outstanding fact of the mineral world today, at home and abroad, is the surplus of current production, and particularly of capacity for production, over current requirements. This is not by Any means a new condition, but never before has it loomed up in such' menacing form. - Those of us who have devoted most of our professional efforts to the discovery and development of 'new mineral supplies now suddenly find ourselves with the job apparently accomplished, waiting for some one else to find an outlet for excess mineral production before we can further. The management of the industry is in much the same boat. The psjrcho16gy of the industry has been so grooved in the direction of acquisition of, minerals that at the present moment the mineral industry confronts the new problem of surplus in more or less of a daze.

Jan 1, 1931

By Clyde E. Williams

THIS review of the progress made in iron and steel metallurgy during the past year is confined to developments in this country. It attempts to give examples to illustrate progress made rather than to appraise results. As a result of the gradually diminishing supply of rich iron ores and of predictions made as to the probable life of the iron-ore reserves of the Lake Superior District, attention of iron and steel executives was directed to the question of beneficiation of iron ores. Laboratory and plant-scale experimental work was conducted on the wash ores .of Minnesota and an investigation, was, begun on the Old Range low-grade ores.

Jan 1, 1931

By H. F. Kendall, J. H. Ffolliott

MANY papers and reports have been devoted to the geology and ore deposits of the Ducktown district, Tennessee, especially the complete report by W. H. Emmons and F. B. Laney, published as Professional Paper 139, by the U. S. Geological Survey. The present paper discusses the work of the geological organization of the Tennessee Copper Co., which is based on the field work of the above paper and the consulting work of W. H. Emmons. The Ducktown basin lies in the southeastern corner of Tennessee and extends a short distance into Georgia and North Carolina. All productive mines are contained in an area of 15 sq. mi. in the center of this basin, which is an undulating plateau at an elevation of 1650 to 1800 ft. above sea level. It is surrounded by the relatively high mountains of the southern Appalachian region. The rocks are of early Cambrian age. Deposition of the ores probably took place during the latter part of the Paleozoic era. The ore deposits are rudely tabular to lens-shaped bodies of massive sulfide, varying from a few feet to over 200 ft. in width. In general they all strike northeast and dip southeast at angles from 45° to 70°. Locally, where affected by folding and faulting, the variations in dip may be even greater. The lodes usually are parallel at distances of from one-half to one mile measured normal to the strike. The deposits are a replacement of a fairly continuous bed or a series of disconnected limestone lenses, highly folded and somewhat faulted, which probably represent the same stratigraphic horizon.

Jan 1, 1933

By Oliver Bowles

GLASS razor blades, glass chairs, and marble window panes attest that creative genius was still active in 1935. Many less striking, though doubtless more important, developments are to be recorded for the nonmetallic mineral industries, and not the least of them is the establishment of an Industrial Minerals Division in the A.I.M.E. under the able leadership of Samuel H. Dolbear, Chairman. Thus the nonmetallics are rightly granted equal dignity with metals and fuels in the category of mineral industries. The brief review of progress that follows merely touches the fringe of important developments in this broad field.

Jan 1, 1936

By Raymond E. Davis

LET'S imagine we are at the Grand L Coulee Dam, where daily 15,000 barrels of low-heat Portland cement and 27,000 tons of processed aggregate in various sizes are mixed to produce 30,000 tons of concrete. Inspect the autographic records which show for each 4-cu-yd. mixer batch of concrete the weights of its constituent materials including its several sizes of aggregate, cement, and water, and which also show the period of mixing and the consistency of the mix. Watch the inspectors sample and test the aggregate for gradation and moisture content of sand, and sample the concrete for homogeneity. Watch the huge buckets deposit the concrete in the forms. It looks too dry to handle, but the concrete vibrators make it melt away. Just enough vibration fully to com- pact the mass, but not enough to produce segregation of the materials; the inspector says when. See the sprinkler system covering all hardening concrete with a spray so that it may not thirst for water. Watch the cleaning of the top of an old lift preparatory to placing a new lift; the sand blasting; the blow-down; the mop-up; the minute inspection.

Jan 1, 1939