Search Documents

By Dan S. Nilsson

When an open pit mine is deepened, more and more waste rock must normally be removed. Techniques for optimization of open pit design are well-established within the mining industry. The recommended method is to choose the open pit alternative with the highest net present capital value of open pit and future underground mining. When the open pit is mined out, the operation must be closed, or, if it is profitable, mining must start underground. When planning an underground operation we experience the same type of optimization problem that occurs when determining the optimal depth for open pit mining. When mining underground the ore body is often divided into a number of areas, blocks or slices, each containing a transportation system with trains, trucks, conveyors, etc. When all the ore within such a part of the deposit is extracted, the operation must be closed, or, if it is profitable, a new transportation must be developed. The question that now arises is: how large a pan of a deposit shall be included in the first development and how much shall be left for future consideration?

Jan 1, 1981

By Brian W. Mackenzie

The mine development decision is made on completion of exploration to determine whether or not a mineral deposit should be developed to production and, if so, how. This involves the selection of an optimum mine development alternative from a number of technically feasible alternatives and the comparison of this optimum with those of other available investment opportunities. If the optimum is sufficiently attractive, the deposit is developed to production. The selection process is carried out within a framework of corporate objectives and resources. The mine development decision is based on the balancing of two parameters - - rate of production as reflected in plant capacity and cut-off grade. On the basis of available information and experience, detailed revenue and cost 'estimates are made for each feasible combination of plant capacity and cut-off grade. What economic evaluation techniques should be applied to these estimates to reduce each alternative to economic indicators that will enable meaningful comparisons and an informed investment decision? This is the essence of the paper. The determination of optimum plant capacity and cut-off grade has been the subject of intensive research efforts by economists and mining engineers (1-7). Their studies are based on marginal analysis and assume that, at the time of decision, certainty conditions prevail with respect to ore reserves, mining costs and mineral markets. The optimum mine development alternative is defined as that which maximizes profitability.

Jan 1, 1969

By Louis A. Panek

An improved centrifugal-testing apparatus has been designed and built in the Bureau of Mines laboratory at College Park, Md., which is unique in that it incorporates the use of resistance gages to measure directly the strains in a rotating model without testing it to failure. Owing to this feature, a more rapid testing method can be used; furthermore, model materials need not be restricted to those of the prototype. The behavior of any structure in which strains of significant magnitude are produced by its own weight may be studied in a small model subjected to simulated gravity loading. The model is rotated in a centrifuge to induce in it centrifugal forces, which, like the gravitational forces in the full-size structure, act on the volume elements and are proportional to the masses thereof. Centrifugal testing is, therefore, applicable to the design of mine openings and to the study of similar ground-control problems. It constitutes an experimental method for determining the state of strain in a structure for which analytical methods are excessively laborious or even impossible. In previous applications of centrifugal testing by other investigators, the models usually were tested to failure, and the analysis was made from-the type of break produced. The models were made of the same materials as the proto-type, and the test results were applied only to the particular prototype represented by the model. Beam deflections were measured from photographs of the rotating model, but no means was employed either to determine the actual distribution of stress in the model or to determine quantitatively the degree of restraint imposed on the ends of the loaded model beam, that is, to determine whether the loaded model behaved as a beam with rigidly fixed ends or as some other type of beam. With the apparatus described, it is possible to determine the state of strain, and thus the boundary conditions, in a rotating test model weighing up to 90 lb., which can be subjected to centrifugal forces up to about 2,600 times the force of gravity. The load-strain relationship, applicable directly to the prototype, can be determined from a Single model test. The test results can be presented as quantitative relations between the loads, strains, and dimensions and mechanical proper-ties of the structural members and can be applied to any prototype, whatever its component materials, that satisfies the similarity requirements.

Jan 1, 1952

By Hillary W. St. Clair

The reduction zone of the iron blast furnace is represented by a mathematical model of the chemical reactions and heat transfer that occurs between gas and solids during the deoxidation of iron oxide. The model consists of a set of equations and an algorithm whereby the equations may be solved to give the temperature and composition of gas and solids at any position in the reaction zone and at any time after a specified initial state. The model is applied to the special case in which ferric oxide is reduced by graphitic carbon and carbon monoxide produced by burning carbon in dry air. The rate of reduction, carbon consumption and maximum temperature are shown as functions of the temperature and rate of flow of the incoming reducing gas and external heat loss. The model of the reduction zone is the essential part of a general mathematical model for simulation of the iron blast furnace. The simulation model will serve as a research tool to be used in conjunction with an experimental or operating furnace. After the simulation model has been correlated with the real furnace, it is proposed that further experimentation be done mostly with the model. The real furnace will then be operated primarily to test and confirm the model.

Jan 1, 1967

By Hugh S. Spence

This paper deals with an occurrence of radium ore near Wilberforce, Haliburton county, Ontario, upon which development work has recently been undertaken and which seems more likely to prove of commercial grade than any other deposit' of radioactive minerals hitherto found in Canada. This occurrence is sometimes called the Richardson property, after Mr. W. M. Richardson, the discoverer, and will be so referred to in the present paper. Occurrences of radioactive minerals are not uncommon in eastern Canada, and a number are recorded in the literature. The earliest of such references is probably that in Geology of Canada, 1863, where is mentioned an occurrence of uraninite at Mamainse, on the east shore of lake Superior. The mineral was first described by J. L. Leconte, in 1847, under the name of coracite, and was said to occur in a two-inch vein at the contact of trap and syenite. Search for this locality in recent years has proved unsuccessful. Obalski, in 1894, mentions (1) the occurrence of uraninite at a mica mine near Murray Bay, Que. In 1903, Obalski records (2) tests made on this uraninite by Rutherford and the Curies and the determination in it of the then newly-discovered element radium. In 1901, he mentions (3) the occurrence of uraninite at the Villeneuve mica mine, on the Lievre river, and of samarskite at the Maisonneuve mica mine, in Berthier county.

Jan 1, 1930

By Larry J. Hulbert, Louis J. Cabri, John L. Campbell, Gilles Laflamme, Chris G. Ryan, Soey H. Sie, Rolando Lastra

"Abstract- The mineralogy of samples from the Wellgreen Cu-Ni-Pt-Pd deposit, Yukon Territory, is complex and the metals of interest are contained within fme-grained minerais which vary in size and mineral associations from sample to sample.The major Ni carriers are pentlandite and violarite; the major Cu carrier is chalcopyrite. About 700Jo of the major Ni carriers and 78% of the major Cu qmier will be liberated at a grind of 80% -'}f,.7 J.Uil (-500 mesh) for typical low-grade gabbro (West zone, sample No. 1). For typical ""clinopyroxenite"" (West zone, sample No. 2) and typical ""clinopyroxene-rich peridotite"" (East zone, sample No. 3) the liberation would be 71""lo and 65% for Ni, 74% and 60% for Cu, respectively. Fine grinding, however, cannot liberate the Ni contained in silicates and pyrrhotite, estimated to total24.5% for typicallow-grade gabbro (West zone, sample No. 1), 15% for typical ""clinopyroxenite"" (West zone, sample No. 2), and 12% for typical ""clinopyroxene-rich peridotite"" (East zone, sample No. 3).The principal Pt carrier (sperrylite) varies considerably in grain-size between samples and fme grinding, required to liberate the major Ni and Cu carriers, may be counterproductive in samples where sperrylite is relatively coarse-grained, as sorne would then be unrecovered (e.g. sample No. 1). In addition, sperrylite in samples No. 2 and No. 3 is closely associated with magnetite.Palladium occurs in diverse ways. It occurs in the form of several Pd minerais (e.g. sudburyite, testibiopalladite, merenskyite), as a replacement for Ni in several tellurides, antimonides and tel­ lurantimonides (e.g. melonite), or as very low concentrations in pentlandite (up to 34 ppm), chal­ copyrite (up to 9 ppm), and pyrrhotite (up to 5.6 ppm). Palladium minerais and Pd-bearing minerals are strongly associated with chalcopyrite in sample No. 1 and will thus report to a Cu concentrate. However, 22% of the total Pd is in solid solution in pentlandite in this sample and will thus report to the Ni concentrate. In samples No. 2 and No. 3, less Pd occurs in solid solution in pentlandite, and the PGM are distributed mainly among pentlandite, chalcopyrite, and magnetite in sample No. 2, and among pentlandite, pyrrhotite, chalcopyrite, and magnetite in sample No. 3. Therefore, the feasibility of magnetic concentration should be investigated for samples like No. 2 and No. 3, in order to improve Pt and Pd recoveries.Rhodium was found to occur as rare hollingworthite, in sparse cobaltite (up to 2.7%) and, as low concentrations in chalcopyrite (to 10 ppm) and pentlandite (to 12 ppm) by proton microprobe. Iridium occurs in hollingworthite (up to 7.8%) and very rarely as the native metal or in an undefmed Re-Ir-Os-Ru alloy. Ruthenium was determined by proton microprobe analyses to occur in pentlandite (up to 13 ppm) and chalcopyrite (up to 10 ppm), in addition to rare laurite and Re alloy."

Jan 1, 1993

By W. F. Watts

This report describes a statistical analysis of 41,502 respirable quartz dust samples collected from 1974 through 1981 in metal and nonmetal mines and mills. The goal of this Bureau of Mines study was to identify commodities and occupations associated with high quartz dust exposure so that future enforcement and research activity can be focused on the high-exposure areas. For this analysis, the Bureau used its computerized Mine Inspection Data Analysis System (MIDAS), which contains data on nearly 350,000 air samples, including data for 61 contaminants in 45 commodities. The samples analyzed were collected by inspectors of the Mine Safety and Health Administration (MS HA). The data were entered into the MIDAS computer and coded according to commodity, occupation, location, and other categorical information. Occupations an. commodities with high quartz dust exposure were identified by grouping the data by code categories. Workers at sandstone, clay and shale, and miscellaneous nonmetallic mineral mills had the highest quartz dust exposures. Within these mills, occupations with high exposures were baggers, general laborers, and persons involved in crushing, grinding, and sizing operations. Dust concentrations in these mills were not necessarily the highest, but because the dust contained a high percentage of quartz, the health risk from dust exposure was the greatest.

Jan 1, 1984

By Earl T. Hayes

[This work represents a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of mineral physics to process metallurgy.]

Jan 1, 1941

By R. C. Buehl

A pyrometallurgical process for recovering manganese from open-hearth furnace slags or low-grade manganiferous iron ores is described. The slag or ore is smelted in a blast furnace to produce spiegeleisen; the speigeleisen is then blown with air in a basic converter to give an oxide slag. This slag product contains 60 to 75 percent manganous oxide and may be considered a synthetic manganese ore. In the smelting operations coke rates for five test periods ranged from 3,255 to 4,130 lb per ton of spiegeleisen. The recovery of manganese in the spiegeleisen varied from 60 to 76 percent. Recovery increased to 83 percent when the open-hearth slag feed to the blast furnace was diluted with a high-? grade iron ore sinter to facilitate smelting. In blowing the spiegeleisen a cyclic procedure was developed that gave nearly 90 percent recovery of manganese in the slag product (synthetic ore) yet prevented excessive contamination of the slag by phosphorus and iron. The overall recovery of manganese was about 75 percent when iron ore sinter was used with the open-hearth slag in the smelting step. The metal remaining after oxidizing the manganese from the spiegeleisen contained approximately 3.5 percent phosphorus. It was refined in a basic converter by blowing with air in the presence of lime" A high--grade iron and a basic phosphate slag were produced.

Jan 1, 1965

By G. C. Lipsyy

ALL mineral production? of Can11.da is transported in a mine car at some stage during its extraction. There are as many types and varieties of mine cars as there are of mines. Many of the cars in use were developed in the blacksmith shop. Others were designed by engineers and improved by the mine foremen and the mechanics. Every mine car has the ideas of miner, blacksmith, mechanic, and engineer incorporated in it. Many of these ideas are not generally known. This paper was written to make at least some of this information available to the mining industry. In drawings, tables, and notes, it gives all the important details pertaining to the cars. It .does not recommend any particular type of car for any particular piece of work, nor does it present drawings from which a car can be built. It gives the engineer or master mechanic information on many cars which he can apply to his own particular problems. It is hoped that this information will be of use to mine operators. If a few new ideas are conceived as a result of the paper, the author will feel that the effort of compiling it has been worth while. In order to obtain the data for the preparation of the paper, a questionnaire, copy of which is here reproduced, was sent to all the operating mining companies in Canada. An accompanying letter briefly explained the purpose of the paper and asked for co-operation in furnishing as complete information as possible.

Jan 1, 1945

By G. S. Rice

The Experimental Mine of the United States Bureau of Mines is a unique coal mine that serves as a large-scale testing laboratory. It is used primarily for testing the explosibility of coal-dust and gases but is also the workshop for many other kinds of research work of which the chief object is to increase safety in mining. The mine is situated in Allegheny County, Pa., about 13 miles southwest of Pittsburgh among the high hills of the west bank of the Monongahela River, at the northeastern edge of the gas-coal district of the Pittsburgh coal bed which extends south through the Connellsville coking-coal district into West Virginia. The Pittsburgh bed, of the Upper Carboniferous age, is one of the most extensive continuous coal beds in the United States, if not in the world. Throughout large areas it shows remarkable uniformity of thickness, levelness, and character of coal, which is a coking coal of high-grade bituminous rank. Its thickness in the northern part is 5 to 5 ½ feet and in the central and southern part is 7 to 9 feet.

Jan 1, 1933

By Robert J. Evans

The monorail bridge conveyor (MBC) is a prototype continuous face haulage system that was surface tested and evaluated by the Bureau of Mines. The MBC consists of a series of cascading belt bridge conveyors suspended from roof-supported monorail track. Tests were conducted to determine MBC haulage capability, maneuverability, power consumption, and reliability using rigid and chain-suspended monorail track installations. Subsequent modifications to improve operation and reliability made during surface testing are described. Mining plans were devised to show potential MBC installations for room-and-pillar, longwall development, and shortwall mining sections. Compatibility tests were conducted with the Bureau's prototype hopper-feeder, to provide additional surge capacity and lump-breaking capability. Results from the surface test program, along with modifications to improve system operation and reliability, indicate that the MBC has the potential to perform success- fully in an in-mine trial.

Jan 1, 1987

By W. W. Stephens

As part of the Bureau of Mines program directed toward more effective utilization of the mineral resources of the United States, a number of processes for production of sponge iron have been investigated. The use of sponge iron as a raw material for production of steels and other ferrous alloys offers several possible advantages over the conventional pig-iron and scrap process, especially for utilization of the smeller, widely distributed iron-ore deposits of the western United States. Although considerable information has been made available on various processes for production of sponge iron, little information 118.6 been published heretofore on the problems and costs involved in melting the sponge iron for production of steel. The present Paper reports the results of tests conducted at the Bureau of Nines pilot plant at Redding, Calif. in which several different types of sponge iron Were used as charge material for production of steel in a 4-ton-capacity basic arc furnace.

Jan 1, 1949

By George Rice

Foreword Following the explosion in the Hillcrest mine, which occurred in the evening of Sunday, September 19th, 1926, and in which two men lost their lives, the writer was invited by the Hon. J.E. Brownlee, Premier of Alberta, to conduct an investigation into the causes of the disaster, and to make such recommendations as seemed advisable with a view to minimizing as far as possible the chance of future explosions in this and similar Alberta coal mines. Accordingly, the mine was visited, and extensive investigations were made underground on October 21st, 2.2.nd, and 25th, in company with Mr. John T. Stirling, Chief Inspector of Mines for Alberta, Mr. Moses Johnson, District Inspector for the Crowsnest Pass District, Mr. J as. A. Richards, Inspector of Mines, Edmonton, and also Mr. Thomas Davies, manager, and other officials of the Hillcrest mine. Hearings of the coroner's inquest were also attended on October 20th and 23rd, when testimony regarding the explosion was given by various witnesses. The following paper summarizes my general observations in tracing the place of origin of the explosion, and my efforts to determine the cause of ignition. Certain recommendations arc also made, and the writer invites discussion on these and the other matters dealt with in the paper.

Jan 1, 1928

By A. C. Richardson, G. D. Coe, B. M. Bird

"The Hull mine of the De'Bardeleben Coal Corporation is located in the Warrior field, in Walker County, Ala., about 25 miles northwest of Birmingham. The Mary Lee bed at this point is coking coal and has been used in the manufacture of by-product coke, but at present it is sold exclusively as a domestic and locomotive fuel.The data in this paper, which is the third in a series on the washability of Alabama coals,5 have been obtained in connection with an exhaustive study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators. The paper contains screen-sizing and float-and.-sink tests of a representative sample of run-of-mine coal, and flakiness tests and crushing tests of certain sizes.In addition, complete analyses of the ¾-inch to 3/16-inch size, raw coal, together with ash fusibility tests of the float-and-sink fractions have been made; those results are given in Tables 1 and 2. Since they indicate that the pr ration problem, like that at Lewisburg, Ala., is one of ash reduction, the further tests and the discussion have been restricted to that subject."

Apr 1, 1931

By R. E. Mitchell

Environmental Impact Assessment (EIA) is the accepted method for evaluating proposed mining and other industrial projects to obtain regulatory approval and to help companies plan for responsible development. Another evaluation system becoming increasingly more common for proposed projects is the Environmental, Social and Health Impact Assessment (ESHIA). An ESHIA differs from an EIA for its more comprehensive and inclusive approach to evaluate potential impacts on public health, and its ecosystem services approach to assessing biodiversity impacts. An ESHIA may also be required by certain lenders for financing major projects. Conducting an ESHIA for a proposed mining development is not without its challenges, with costs, scheduling, regulatory concordance and other constraints to be considered. This paper examines some benefits and challenges of ESHIAs and summarizes lessons learned using a case study approach.

Jan 1, 2012

By Richard L. Ash

Usually stresses generated by explosive charges during blasting are considered to propagate through materials in a spherical manner. Although conical stress-waves had been suggested by a few investigators they have never been clearly defined or critically observed. An experimental technique using models and lengths of Mild Detonating Fuse was developed to produce conical stress-waves and study their effects. Several materials with different properties were tested to compare the influence of those properties on wave shape and crater formation. The investigations showed that whenever column charges were end-initiated, conical stress-forms were produced if the explosive's velocity exceeded the energy propagation velocity of the surrounding material. The stress-cone angle significantly affected fragment size and shape as well as the geometry of craters produced.

Jan 1, 1967

By H. C. Miller

The removal of the mud sheaths that are deposited against the faces of productive oil sands during rotary drilling is one of the important problems confronting operators, especially in semidepleted fields where formation pressures are low. Unless the mud sheaths behind the perforated oil strings and, liners are removed and the sands exposed, oil cannot enter the wells. Consequently much oil that otherwise eight be produced from low-pressure sands is trapped and never recovered. Various types of perforation washers, down swabs, and agitators are used at present for breaking down the mud sheaths and. removing the disintegrated clay particles from wells after the perforated pipes have been inserted. Mechanical methods for removing mud sheaths are quite satisfactory, but prompted by tie request of certain operators in the California oil fields Bureau of Mines engineers have conducted a series of laboratory tests with the view of developing a chemical method for removing mud sheaths in oil wells that will be applicable to field conditions.

Jan 1, 1934

By D. C. Yates, G. V. Jolliffe

In the five coalfields of Staffordshire, there have been some 43 incidents of spontaneous fires and heatings which have required special attention in the past ten years. This total excludes incidents in the Thick Coal Seam of South Staffordshire, which was worked until 1967, and which was subject to an almost continuous series of heatings. The incidents have been classified to show the sites of occurrence, the contributory factors which may have caused them and the treatments applied to them. The remedial techniques, as practised in Staffordshire, are dealt with in detail, with particular reference to standard methods of stopping-off. Precautionary measures taken are described, including a "liability to spontaneous combustion" classification of all seams, and the setting up of an emergency organization with emergency stocks of materials and equipment. The paper is concluded by a few words on the organization and control at the time of an incident.

May 23, 1905

By F. Cappel

Except in a few special cases, it is necessary for solid fuel direct reduction in rotary kilns that iron-bearing materials be charged with a minimum grainsize of approx. 5 mm. For fines not usable in such form, the combination of sintering - as agglomeration step - and direct reduction were investigated. During reduction of sinter in rotary kilns prevail dependencies on sinter quality and varying reaction parameters, owing to the use of different coals, which led to a definite statement as to what quality sinter must have and which coals can be used.

Jan 1, 1983