Search Documents

By Tapiwa Chenje, Victor Olivas, Peter Radziszewski

"Ore breakage and grinding media wear have always been considered and determined separately in laboratory tests. However the two processes are linked with the ore broken down in any comminution device being responsible for the majority of the steel wear experienced. The Comminution Dynamics Laboratory (CDLab) successfully developed a test methodology that can more accurately predict grinding media wear in tumbling mills than the Bond Abrasion test. This paper looks at the possible application of the abrasive wear methodology to determine breakage parameters of the same ore used in the abrasion test. Results indicate that breakage parameters comparable to t10 can be determined using the Steel Wheel Abrasion Test (SWAT), while using significantly less ore than standard breakage tests.BACKGROUNDThe Rubber Wheel Abrasion Test (RWAT) is an internationally accepted and widely used method for determining the abrasion wear behavior of materials. The abrasion wheel test was developed to primarily utilize a steel wheel (Brinell, 1921). Haworth (1949) criticized using of the steel wheel by arguing that increasing the contact area size in the steel wheel test causes a change in the wear rate with time. He suggested that the use of a rubber wheel instead eliminates this problem, leading to the adoption of the RWAT which was standardized in ASTM G65 (2004).Radziszewski (2002), however, found that the use of the Steel Wheel Abrasion Test (SWAT) was more applicable for wear testing in the mining industry for two critical reasons. Firstly, the major cause of wear in a ball mill, the most frequently used comminution device, is ball-ore-ball contact and also ball-ore-liner which both are metal-ore-metal contact. Therefore, using the steel wheel has the advantage of providing a similar abrasive environment to the one that takes place in a real ball mill. Secondly, the SWAT creates the potential of running experiments at much higher force regimes that are closer to what happens in actual mills, unlike the RWAT which is a low stress test."

Jan 1, 2011

By Rodolfo Espinosa

"Industrias Peñoles, S.A. de C.V. in Mexico, has nine mining operations, six managed by Peñoles (base metal mines) and three managed by Fresnillo plc (precious metal mines). Seven of the operations use flotation and the other two are heap leach operations, one for gold and the other one for copper.This paper gives a brief introduction of Peñoles, shows mine locations and describes the main process characteristics of each concentrator. It also presents four of the new operating practices that were implemented over the last four years to improve the economics of the mining operations. These include (1) the use of centrifugal gravity concentrators to increase the recovery of gravity recoverable gold (GRG) and silver (GRS), (2) the use of expert systems to reduce process variability while increasing grades and recoveries, (3) the application of the Six Sigma methodology to key projects to ensure success and personnel development and (4) the use of water chemistry fundamentals to identify chemistry problems and design adequate solutions for improving grades and recoveries.INTRODUCTIONPeñoles was founded in 1887. It is a mining group with integrated smelting, refining and chemicals producing operations. Peñoles is the world largest producer of refined silver and metallic bismuth, the leading Latin American producer of refined gold and lead. It is amongst the world leading producers of refined zinc and sodium sulfate.Peñoles operates and controls six underground mines in Mexico and is the largest producer of zinc and lead of the country. It also produces copper concentrates and cathodes. Through its 77.1% equity stake in Fresnillo plc (a London Stock Exchange listed company); Peñoles is also a significant producer of gold and silver. Fresnillo plc operates three precious metal mines in Mexico. While Fresnillo is the world largest primary silver mine, Ciénega and Herradura are two leading gold mines of Mexico. Figure 1 shows a map of Mexico indicating the locations of the Peñoles mines. The main process characteristics of each concentrator are listed in Table 1."

Jan 1, 2011

By R. L. Virta

Ball Clay -- Four companies - H.C. Spinks Clay Co. Inc. (owned by Lhoist Group), Imerys Group (formerly Kentucky-Tennessee Clay Co.), Old Hickory Clay Co. and Unimin Corp. - mined ball clay in four states during 2010. Production, based on preliminary data, was 910 kt (1.11 million st) with an estimated value of $42.9 million. That was a 10-percent increase in tonnage from 831 kt (916 million st) with a value of $37.7 million that was produced in 2009. Tennessee was the leading producer state with 61 percent of domestic production. It was followed by Texas, Mississippi and Kentucky. About 70 percent of production was airfloat, 20 percent was crude and 10 percent was water-slurried.

Jan 1, 2011

By Robert Louis Adams

A general discussion of the structure of the junk automobile recycling system shows that the generation of stripped automobile hulks and scrapped automobiles is price inelastic. As a result, it is extremely difficult for the price mechanism to automatically achieve an equilibrium that will prevent the accumulation of excessive automobile wrecker inventories and vehicle abandonment by the last owners of scrapped cars. The new shredder processing technology and the new portable flattener technology have altered the structure of the junk automobile recycling system. The shredder technology has increased the demand for processed automobile scrap. This increased demand is reflected in higher prices paid for hulks by scrap processors. The portable flattener has reduced the transportation cost of shipping hulks to processors. The two new technologies have eliminated, at least potentially, the net cost of shipping stripped hulks so frequently incurred by wreckers in the past. The elimination of this cost eliminates the economic incentive for excessive wrecker inventories. Unfortunately, the incentive for last owners to abandon their cars does not appear to have been eliminated by the new technologies. The last owner of an automobile with no spare parts value is still likely to incur a cost by delivering his automobile to the recycling system. Although a subsidy payment is probably unnecessary to reduce excessive wrecker inventories, such a payment might be one solution to the problem of automobile abandonment. However, there are a wide variety of subsidy programs that could be introduced. Before any Federal subsidy program is introduced to reduce automobile abandonment, it is recommended that the program be tested on a limited basis in many different parts of the country.

Jan 1, 1973

By R. Farrar

Protective canopies for conventional electric face equipment, including shuttle cars, operating in low coal (less than 48 inches) were designed, fabricated, installed and evaluated on in-mine machines engaged in regular coal mining operations. This work was performed under contract to the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center. The canopies will support a vertical load of 18,000 pounds and provide protection against both roof falls and contact with the mine rib. Canopy configurations were established based on human engineering studies, full scale canopy mockups, and in-mine observation and consultation with mine and equipment manufacturing personnel. Overall height of each canopy is hydraulically adjustable between a minimum of 32 inches and a maximum of 40 inches. Canopy tops are open framework, welded structures, covered with expanded metal mesh. Structural members are 1 3/4-inch or 2-inch square tubing of AISI 413ON and ASTM A500 material, respectively. The canopy tops are typically supported by an understructure and upright post arrangement that is either integrated into the current operator platform or attached to the machine frame. The four upright corner posts house the hydraulic actuators. Canopy tops are elevated horizontally. Canopies are welded or bolted to the existing machines. Installation is accomplished with a minimal amount of interface modifications. No major machine design changes are required. Canopies were trial installed and load tested at the manufacturer's facility prior to installation on the in-mine machines. Canopies were installed on a Joy 14BU10 Loader, 16RB-3AH Cutter, and two 21SC Shuttle Cars, and a Galis 300 Roof Drill and 460-S Face Drill. Canopy installations were evaluated in the Jewell Ridge Coal Company No. 12 and Big Creek Tiller Mines. Operational time accumulated on the installations during evaluation ranged from 1 week to 14 weeks of two-shift operation. All five canopy designs, manufacture, and test were successfully accomplished. The five canopies met all safety requirements. Three of the five canopies were deemed to be completely successful from an operator's point of view. That is, mine management as well as the machine operator found that the canopies did not impede the operation of the machines to function with the same efficiency as before the installation of the canopies. The loader canopy, in fact, appeared to have provided a mole efficient operation of the loader by providing added safety to the operator from rib contact thus allowing him to concentrate more fully on the loading function. Operational problems were encountered with the shuttle car and the roof drill. The shuttle car canopy obstructed visibility to an objectionable amount and the roof drill canopy impeded maneuverability of the machine, more than doubling the roof bolting time.

Jan 1, 2012

By R. E. Chaney

This report summarizes the research on the Strategic and Critical Materials Program tasks conducted at the Idaho National Engineering Laboratory (INEL) between May 1984 and April 1985. The work is divided into two areas: 1. Production Technologies - Tasks directed at developing advanced extraction technologies ? Biologically-Assisted Minerals Processing ? Metal/Gas Reactions and Thermal Plasmas ? Dehydration of Aluminum Chloride Hexahydrate (completed). 2. Conservation/Substitution Technologies - Tasks directed toward establishing the technical processing base which will permit the use of advanced materials ? Joining of Rapidly Solidified Alloys (RSA) ? Joining of Silicon Nitride-Based Ceramics ? Nondestructive Evaluation of Ceramic and RSA Joints and Materials ? Substitute Catalytic Materials for Platinum.

Jan 1, 1985

By H. F. Yancey

One of the important duties of the Bureau of Mines is to sample and analyze coals and to publish the results of such analyses for the information of producers, consumers, and the general public. Numerous publications containing such analyses have been Issued from time to time. Although the chemical properties of a coal as revealed by its proximate and/or ultimate analysis and heating value aid one considerably in visualizing its probable behavior and in determining its usefulness and value for a specific purpose, they do not furnish complete information. The physical properties of a coal, such as its ability to retain its original form without undue breakage or degradation in size under the various conditions of storage and usage, are also of importance in determining its suitability, technically or economically, for a given purpose.

Jan 1, 1932

By John H. Johnson

This report covers the third and final year of work conducted under U. S. Bureau of Mines Grant G0166027, "Monitoring of Mine Air Pollutants". The report discusses work performed in three areas. These are the White Pine Mine (WPM) Experimental Unit, diesel mine-vehicle tailpipe emissions monitoring, and mine ambient air concentration data analysis. The WPM experimental unit was used to study diesel exhaust stratification in an 80 foot long dead-end heading while loading ore with a Wagner ST-5D scoop train LHD. The MTU Mine Air Monitoring Laboratory (MAML) was used to gather temperature and CO2 concentration data at 10 locations. Three different ventilation conditions were compared. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in temperature stratification in dead-end headings. The diesel mine-vehicle tailpipe emissions monitoring study involved laboratory measurements of diesel undiluted exhaust pollutant concentrations by the portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. The mine ambient air concentration data analysis study included analysis of diesel pollutant concentration data in the Orchard Valley Mine air and comparison of the results with data collected earlier in the White Pine and Brushy Creek mines. The analysis included preparation of lognormal frequency distributions and calculations of C02-based concentration ratios and correlations. In the three mines compared, pollutant concentrations are distributed quite similarly, and the concentrations appear to be controlled to present standards.

Jan 1, 1979

By L. C. IlsLey

Explosives have been fired electrically for several decades. Mountains have been tunneled, deep shafts sunk, extensive coal and metal mine workings excavated and, in times of war, railroads, buildings, bridges, and fortifications have been destroyed by means of electrically fired explosives. Modern engineering depends so much on explosives that their safe and efficient handling and especially their detonation are of prime importance to all those connected with the use of explosive agents. Electric shot-firing is only one method of igniting explosives, but it is rapidly spreading and because of certain inherent safety features should be encouraged. Data collected by the Bureau of Mines indicate that in the United States a large percentage of the blasting in quarries, shafts, and tunnels, and from 15 to 25 per cent of the blasts in mining operations, are set off electrically. The Bureau of Mines is interested in electric shot-firing because of its use in mining, and especially because electric methods, when properly applied, are undoubtedly safer than other methods commonly used.

Jan 1, 1926

By Robert L. Frantz

This report is a part of the project "Study of the Human Factors Aspects of an Automated Continuous Mining Section". The report covers three phases: Phase I Assessment of the Impact of the Automation Technology on Mining Health and Safety. Phase II Estimation of the Cost-Effectiveness and Productivity of Automation. Phase III Prediction of the Psychological and Organizational Impacts of Automated Mining, The investigation determines that the automation of a continuous mining section will improve the health and safety of the miner, increase productivity and decrease mining costs, result in a more attractive and desirable working environment, and result in a greater rate of return on capital investment.

Jan 1, 1977

By Charles Enzian, Donald F. MacDonald

It is a far cry from the small and uncertain mining efforts of 50 years ago to the splendidly equipped and solidly financed organiza- tions that now handle thousands of tons of ore per day. The old mining was largely speculative; the new is practically on a manu- facturing basis. In the old days of mining the aim was, chiefly, to find comparatively rich ore; modern practice looks more toward efficiency in mining and milling, so that vast tonnages of low-grade material may be worked at a profit. The old operators had faith and hoped for good returns; the new ascertain with a fair degree of precision what the available tonnage is, what the cost of mining and treating the ore will be, the time necessary to exhaust the deposit, the capital required, and the net profits to be made. The old mining was financed on a highly speculative basis, and the value of mining stock was largely controlled by the imaginations of the promoters and of the individual holders. In the new régime the financing of mines is often as conservative as the financing of manufactures or railroads, and the value of stock, quoted on the leading exchanges, is controlled by the carefully estimated profits in sight. Of course, with every legitimate industrial enterprise go certain business risks, and mining is not exempted from these. Then, too, valueless mining as well as valueless industrial stocks are sometimes offered for sale by the intentionally dishonest, or the ignorant. However, the prospective purchaser of a mine nowadays, if he is willing to pay for the services of reputable mining engineers, can obtain information on which to base an opinion as to the quality of his investment. The relatively recent development of cheap and efficient methods of mining and of ore dressing has given value to low-grade ore bodies that a few years ago were almost valueless. The iron mines of northern Minnesota have been fruitful in developing efficiency in mining methods, notably the open-cut methods in which steam shovels strip off the overburden and then load the ore directly into railroad trains for transport to the furnace. In 1907 open-cut mining was applied to the low-grade copper ores of Bingham, Utah, with splendid results, and since then it has won a most important place in the min- ing of large masses of low-grade ores in several other mining regions, especially at Santa Rita, N. Mex.

Jan 1, 1916

By A. B. Hooker, L. C. IlsLey

Explosives have been fired electrically for several decades. Mountains have been tunneled, deep shafts sunk, extensive coal and metal mine workings excavated and, in times of war, railroads, buildings, bridges, and fortifications have been destroyed by means of electrically fired explosives. Modern engineering depends so much on explosives that their safe and efficient handling and especially their detonation are of prime importance to all those connected with the use of explosive agents. Electric shot-firing is only one method of igniting explosives, but it is rapidly spreading and because of certain inherent safety features should be encouraged. Data collected by the Bureau of Mines indicate that in the United States a large percentage of the blasting in quarries, shafts,· and tunnels, and from 15 to 25 per cent of the blasts in mining operations, are set off electrically. The Bureau of Mines is interested in electric shot-firing because of its use in mining, and especially because electric methods, when properly applied, are undoubtedly safer than other methods commonly used. Electrical problems of many kinds must be solved in dealing with the various phases of electric shot-firing. Success in using an electric detonator is closely linked with the resistance of its bridge, the resistance of its leg wires, and the insulation of its current-carrying parts. The proper layout of a circuit where a number of shots are to be fired simultaneously depends not only on the types of detonators that are used and their arrangement and interconnections, but also on the size and insulation of the wire leading back to the source of power, and even on the source of power itself. Various types of electric shot-firing machines have been developed, and these offer still another field for study. In investigations of electric detonators and electric blasting equipment, the oscillograph is valuable because it can record electrical activity over very short intervals of time. By its use more complete information about electrical performance can be obtained than by any other means.

Jan 1, 1926

By K. K. Landes

The north central and northeastern states supply over 50 pct of the chemical and metallurgical limestone produced annually in the United States, and Ontario is the leading source of this material in Canada. About three fourths of the chemical and metallurgical stone produced in this area comes from Michigan, Pennsylvania, Ohio, and Ontario. The specifications, physical and especially chemical, for chemical and metallurgical stone depend upon the end use, but in general the tolerance for impurities is so low as to rule out most limestones and dolomites. Both high calcium limestone and dolomite are used in the metallurgical and chemical industries. The principal metallurgical use is as a flux in iron ore blast furnaces and open hearth steel furnaces. The major chemical uses are in lime burning and soda-ash manufacture. Other important uses include glass manufacture, in making calcium carbide, and in sugar factories. All deposits of high quality carbonate rock are definitely finite. Invariably and inevitably they diminish in either thickness or quality laterally so as to become unworkable as chemical and metallurgical stone. The size of these high quality lenses ranges from a few thousands of tons to hundreds of millions of tons. The best hunting for new supplies is in the geologic formations known to contain premium quality deposits. However, because of high transportation costs, carbonate rocks, to be workable, must be close to market, dollarwise. Definitions: Chemical stone is limestone or dolomite used as a raw material by the chemical industry. The major chemical uses are in lime burning and soda-ash manufacture. Other important uses include glass manufacture, making calcium carbide, and in sugar factories. The specifications for chemical stone depend entirely upon the end product. Some uses require dolomite, some require high calcium limestone; in a few instances, notably in lime burning, either type of carbonate rock can be used as raw material. As a general rule, a fairly pure stone is necessary and for certain particular uses the tolerance for some elements such as sulfur, iron, and phosphorus may be extremely small. Metallurgical stone is used as a flux in furnace operations, especially in the blast furnace where iron ore is converted into pig iron and in the open hearth furnace where pig iron is made into steel. Either limestone or dolomite can be used in the blast furnace, but only high calcium stone is charged in the open hearth (except for rice-size dolomite used as a refractory). There are no rigid chemical specifications for blast furnace stone, but low silica, alumina, sulfur, and phosphorus are desirable. For open hearth use, in addition to low magnesia, a very low sulfur content is also specified by many furnace operators. For furnace use, fluxstone also must be sufficiently shatter resistant that it will remain in lump form during transport and charging into the furnace. Commercial stone is the term applied in the trade for crushed stone used for roadstone and in concrete aggregate. Many of our best chemical and metallurgical limestones are too soft to qualify in the Los Angeles abrasion test for use as commercial stone. However, some limestones, and a higher proportion of dolomites, do qualify for commercial stone and so can be sold to either market. Place Value: Even the highest grade limestone is still a bulk commodity with a relatively low value per ton. As a matter of fact there is very little difference in the average price per ton between high grade chemical and metallurgical stone and crushed limestone used commercially. Most high quality stone is produced in large operations with consequent low cost per ton whereas most commercial stone is produced in relatively small local quarries. As in the case of other bulk commodities most limestone buyers pay more for transporting the raw material than the cost of the stone at its source. For this reason steel furnaces and chemical plants

Jan 1, 1961

WHEN reading reports on reefs and lodes, one often comes across the statements "short shoot," "narrow shoot," "wide shoot," & c.From a number of reports in the writer's possession, some by members of the Geological survey, it is plain that the words "short," "narrow," "wide," "long;" &c., are used somewhat carelessly.In one official report on a certain field, for instance, the reefs are described as having "short, rich shoots"; another report on the same field states that "the reefs were characterized by narrow shoots, rich at the surface." Again, Charters Towers is described as having "wide shoots"; another writer says they are "long shoots. "The writer has read again of "short shoots which went down like pipes," and of "narrow shoots of limited extent." No doubt one can make out what is really meant, but the language is mixed. It is apparent that "narrow" is meaning the same as "short," and that the shoot has not much length in a horizontal direction. Nothing is said about the thickness or width of 'said shoot, or its depth. The "wide" shoot is evidently a "long" one; its thickness 01' width and depth is not specified. When we consider these terms, it is seen that only a few words are needed, and that these few should (as they do) have a definite meaning. In the course of his mining experience, the writer has seen shoots of almost all sizes, and some have been very long (in horizontal measurement), and have been followed down for great depths, these shoots being the best type-Charters Towers, Walhalla, &c., are examples.

Jan 1, 1909

By Magnus Troilius

The method of using the bromine process of determining sulphur in steel, described below, is in successful use at the Midvale Steel Works. Ten grams of drillings are weighed out and put into the 1/2-liter flask A, with long neck. The flask is connected with a wide glass tube C', which, in its turn, is connected with the absorption bulbs B, containing HCI, 1.12 specific gravity, and ahout 5 C.C. of bromine. The wide tnbe C causes the vapor to condense and flow back into the flask A during boiling. The bulbs B connect with a long glass tnbe, which may be made to carry off the bromine fumes through a hole in a window, or, better still, through a flue with powerful draught. The connections being made, 100 C.C. of boiling water are run in through the thistle tube T. The air is thus completely driven out of the flask. 100 C.C. of HC1 (about 1.19 specific gravity) are then run in. When the gas begins to run rattler slowly through B, heat is applied until boiling gradually ensues. The steel being completely dissolved, the apparatus is disconnected, and the contents of B rinsed out into a beaker of 100 C.C. capacity, into which a few C.C. of a concentrated solution of BaCI, have been previously introduced. Heat is then applied (best by means of the hot iron plate) until the bromine is completely driven off and the BaSO, has settled nicely to the bottom. The BaSO4, is then filtered off on a small

Jan 1, 1884

By Biao Zhou, Qian Li, Kuo-Chih Chou, Yi-Long Liang, Jie-Yu Zhang, Qun Luo

"In this work, the phase transformational behaviors and microstructural characteristics of 60Si2CrVAT spring steel were systematically investigated as a function of applied cooling rates in the range of 0.l-10°C/s. A quenching deformation dilatometer was used to austenize and quench. The dilatometric curves between length changes and temperature of samples suggest three characteristic stages could be identified as different ranges of cooling rates, which meets well with metallographic examination and the measured hardness results. As the cooling rate increases, the structure transformed from pearlite, granular bainite to finally martensite. The F + P and B zones are completely overlapping in continuous cooling transformation (CCI) curve, which indicates that this steel is difficult to become single bainite and shows good hardenability.IntroductionThe 60Si2CrVAT, a high-carbon low ally super-high strength steel developed from the ?OCT 60C2XFA and 60Si2MnA, is often used for coil spring of heavy vehicles and high-speed railway by hot deformation or cold deformation [1-3]. The addition of Si improves relaxation resistance significantly, through the refinement of tempered carbides as the result of the retardation of E -carbide conversion to cementite during tempering. Due to its deleterious effects on decarburization and toughness, the maxinJum content of Si has limited to 1.5 or 2.0% [4-5]. Additionally, V and Cr can improve sag resistance due to the precipitation of fine carbonitrides during hot rolling [6-7]. To best of our knowledge, the strengthening by precipitation of alloy carbides of Cr and V often referred to secondary hardening [8]."

Jan 1, 2013

By K. Rüter

Sustainable investment is a global growth market. Companies that can reconcile economic, environmental and social objectives not only minimise risks, but also realise significant potentials of added value. This particularly applies to the metals & mining industry, as it is an attractive sector for investors and, at the same time, faces major challenges in the field of sustainable development. oekom research AG is an independent rating agency specialised in the analysis and evaluation of the environmental and social performance of companies, sectors and countries for institutional investors and financial service providers in the socially responsible investment (SRI) sector. oekom research has been active in the sustainable investment field since 1993 and its research is currently being used by managers of more than 60 bond and share funds with a volume of assets totalling more than 4.5 billion Euro. The company?s research and its central instrument, the Corporate Responsibility Rating (CRR), are based on the world's most comprehensive set of criteria for the ethical assessment of companies. With the support of an independent scientific advisory board, these universal and industry-specific sustainability criteria are being constantly updated reflecting the dynamics of global challenges in sustainable development. Increasingly, the rating results and benchmark reports of oekom research are also being recognised by the companies as a valuable tool to identify best practices, areas for improvement, and potential risks. This paper will outline the methodology of oekom research, the identification of key sustainability issues in the metals & mining industry, the development of industry-specific sustainability criteria (indicators) for the assessment of the metals & mining industry and key findings of the recently completed CRR of twenty major metals & mining companies.

Jan 1, 2007

By Anatoly F. Usov, Vyacheslav A. Tsukerman

"The Russian scientists have developed a new energy saving method for an efficient destruction of the sturdy and hard materials (rocks, ores, frozen soils, concrete blocks ets.) - the Electric Pulse Discharge method of materials destruction (EPD). The detailed researches of a broad circle of problems connected to development EPD-disintegration of materials of a various nature and area of use are executed. The electrical and power characteristics of process, physical fundamentals of selectivity of a breakdown and destruction are investigated, the means of electric pulse splitting and refinements of materials are developed, the technological efficiency of disintegration of industrial minerals estimated.One of the most important characteristics of the EPD-disintegration of ores is the high selectivity of destruction, which provides a large ratio of useful minerals' grains opening, and at the same time, it destroy them less. This ensures in the subsequent stages of beneficiation of ores considerable increase of the extraction and improving the quality of concentrates.The technological tests of various industrial minerals have shown a possibility the EPD-disintegration, as a process that provides the best efficiency of disclosure of useful minerals in all types of ores. Technological and economic efficiency of the method of ore beneficiation is the highest for difficult beneficiated ores with rather low extraction by existing methods. The increase of extraction in this case can reach several percents. As a rule, at a EPD-disintegration the disclosure of mineral grains happens in earlier stages of material comminution than at a mechanical comminution, and with less damage of products. This promotes a simplifying the process of ore preparation and for reducing the power consumption."

Jan 1, 2003

By H. Foster Bain

In the preparation of this series of books it was considered particularly appropriate to include this work. Gunther was one of the younger men who was associated with Colonel Mudd in the finding and development of ore deposits. Supported by Mudd, Gunther undertook a systematic survey of the sources of copper of ancient Europe. This survey resulted in the rediscovery of the deposits now worked by the Cyprus Mines Corporation for which Gunther was, until shortly before his death, the resident manager. In finding and developing these mines, Gunther applied the methods and data embodied in this book and proved their usefulness. It is believed that other young engineers may profit similarly. In presenting a new edition, the form and substance of this work have been preserved and no changes have been made in any direct statement of the original author. Individual illustrations, paragraphs and mine descriptions appearing in the first edition have been omitted in order to permit introduction of new material. The latter has been chosen so as to present a somewhat more balanced picture of the mining industry as it now exists. The new material relates largely to the so-called porphyry coppers, to mines in Canada, Rhodesia, Alaska, and a number in the United States that have become important since the book was first written. The new material was prepared by Mr. Russell C. Fleming, using the best that had been published and items of which he had personal knowledge or had obtained by correspondence with men familiar with the deposit described. Whenever possible the description used has been submitted to the original author for correction. In a number of instances

Jan 1, 1932

The following resolution was prepared, by the War Minerals Committee and was submitted by it to the Board of Directors of the American Institute of Mining Engineers, asking that it be passed by the Board and used to the best advantage to secure the end desired. WHEREAS, the steel industry of the United States is almost entirely dependent on the importation of foreign manganese ores, the consumption of which for the year 1918, it is estimated, will exceed 850,000 tons; and WHEREAS, the ships now engaged in transportation, especially from Brazil, are needed with ever increasing urgency for supplying our Army and Navy forces abroad; and WHEREAS, much shipping may be spared from manganese transportation and the domestic sources of manganese may be utilized, provided the steel manufacturers of the United States will cooperate to this end by taking advantage of the possibility, in open-hearth and Bessemer practice, of so called "residual" manganese, and by using spiegeleisen instead of ferromanganese, thereby following the example already set by three large and prominent steel producers; BE IT RESOLVED, that the Board of Directors of the American Institute of Mining Engineers urges the steel manufacturers of America, for patriotic reasons, to give immediate consideration to the development and utilization of domestic manganese ores; to use no ferromanganese, except for the manufacture of grades of steel below 0.15 per cent. carbon, to use domestic ores whenever possible in place of the high-grade imported ores; and to urge their associates and colleagues in this and other possible ways, to vie with one another in releasing ships for importation of any materials that cannot be secured or produced in this country.

Jan 1, 1918