Search Documents

By R. B. Crookston

This paper presents the status and mining method chosen by each of the active underground oil shale projects in the united States today. Potential improvements in equipment and methods on the near-term horizon are discussed. The problems and potentials that lie in the long-term future of oil shale mining are examined in light of the demands which must be met by this developing technology.

Jan 1, 1981

By Allen H. Rogers

It has always seemed to me that there is a certain similarity between the work of the mining engineer and that of the doctor of medicine — each has very often to be governed in his actions by conditions which he cannot see. It is not necessary to detail the unseen conditions with which the mining engineer or geologist has to deal—the further extension of ore-bodies, the existence of new ones, the throw of a fault, the probable change in grade' or character of the ore with advance of the workings, are a few of the conditions which the mining engineer has to determine as well as he can from the deductions he is able to make from what he can observe. Just so the physician is often confronted with conditions that he can not observe. Probably less than half of human ills make a manifestation at the surface of the body from which definite and certain conclusions can be drawn. The diagnostician must observe various things and, from these observations in combination, conclude what his course should he to bring about the cure of the trouble. Both professions would be assisted immensely by any agency that would permit them to look below the surface, something that would make more certain the diagnosis which each is called upon to make. The physician has had such an agency since 1895, when Röntgen discovered the X-ray; which, by making possible shadowgraphs of the osseous portion of the human body, advanced immensely the diagnosis of bone lesions Later, with improvement in the technique and more understanding in the interpretation of what the photographic plate shows, other portions of the human anatomy could be examined and at the present time there is hardly an instance of internal disorder to which the aid of the X-ray is not called. Some organs are made opaque by administering mineral substances; in other cases, conclusions are drawn from barely perceptible shadows on the photographic plate. Generally the surgeon's knife is directcd with exactitude to the seat of the trouble and so not only is the difficulty revealed but the necessity for an exploratory operation is averted. What the X-ray is to medicine and surgery, geophysical prospecting methods are to the mineral industry. They give the mining engineer and geologist information regarding subsurface conditions which otherwise

Jan 1, 1929

By John Owens, Hamid Maleki

Efficient and safe use of mobile roof supports (MRS) depends on the interaction between the MRS and coal strata. Of particular interest to this study are the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods, and MRS load-bearing capabilities. To provide a better understanding of the mechanics of strata deformation, the authors have collected and reviewed measurements of convergence and stress in one western U.S. mine and have completed pseudo-three-dimensional, boundary-element modeling for two typical pillar-pulling plans. Stress distribution in the mine roof above pairs of MRS’s was calculated to demonstrate how MRS’s contributed to the control of roof block movements. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal-measure rocks and by pillar-pulling sequences and layouts. MRS’s and other support systems play a critical role in controlling the stability of both the immediate roof and the middle roof for a distance of up to 18 m (60ft) above the seam. MRS’s provide unique ground control advantages over other types of secondary support by significantly reducing the time between mining and installation of secondary support. Although MRS’s are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at near-peak capacity, whereas posts fail and loose their ability to limit mine roof deformation.

By Sean Hillacre, Arthur Lieu

NexGen’s approach to uranium processing design including the crushing/grinding and leaching of raw ore through to yellowcake precipitation and tailings management focuses on minimizing surface footprint, freshwater consumption, and human radiation exposure. Applying the concept of best available technologies economically achievable (“BATEA”), NexGen continues to research, evaluate, test and validate various advanced technologies that can be incorporated into the Project design, including distinctive tailings storage techniques. Additionally, NexGen is proposing that tailings generated from the mill processes be used as cemented paste backfill of stopes, as well as stored in a purpose-built, Underground Tailings Management Facility (“UGTMF”) comprised of several dedicated chambers. The paste backfill method of tailings storage is used globally, however, constructing purpose-built tailings chambers in waste rock is a new concept in uranium mining, which would typically be cost prohibitive for most projects given the expense to develop non-economic material for the sole purpose of storing tailings. The Rook I Project is uniquely positioned to implement the UGTMF due to robust Project economics and favourable technical setting which provides NexGen with the opportunity to set an elite standard for tailings management. When compared to conventional surface tailings management facilities, storing tailings underground as cemented paste reduces geotechnical, geochemical, environmental, and human health risks associated with tailings management. Additionally, the UGTMF vastly reduces the area of surface disturbance and allows for progressive decommissioning during the life of mine operations.

Jan 1, 2020

By T. M. Yegulalp

Geometric programming is a mathematical optimization technique, first formulated by Zener [1], for dealing with certain types of functions which typically arise in engineering design problems. The theory provides algorithms for finding the optimal solution, existence theorems by which one can show that a particular design is possible or not; and characterization theorems that especially make possible to obtain the relationships among the optimal design parameters at optimum. It has been demonstrated [2] that this technique can be applied to several design problems in chemical, electrical and mechanical engineering. Design problems in mining, metallurgical and mineral engineering have many aspects similar to that of other engineering problems. Thus it is only natural to consider geometric programming as a potential tool for solving certain optimization problems in mineral industries.

Jan 1, 1974

By Ulrich Leiste

If the iron ore loss is 15% in the process of mining, the total iron ore loss in the world will be about 461 million tons, this is equal to the total production of 230 iron ore mines each of which produces 2 million-tons of iron ore per year. Based on a series of blast tests in the Malmberget mine, this paper shows that ore recovery can be markedly increased by improving blasting technology such as choosing a correct primer position and making use of shock wave collision. The paper further suggests that a high ore recovery can not only reduce natural resource loss and mining cost but also prolong the life of a mine. In addition, the paper shows an example of reducing blast-caused rock damage in the roofs and walls of underground drifts (tunnels) by using new blasting methods in the Malmberget mine. Finally, the paper shows how the Malmberget mine has successfully reduced the ground vibrations, without adversely affecting fragmentation and ore recovery in sublevel caving mining.

Jan 1, 2014

By Gerald T. Homce

Accidental contact of overhead electrical power lines by mobile equipment is a leading cause of occupational fatalities in the United States, accounting for 20% of on-the-job electrocutions. Overhead electrical power line proximity warning devices (PWDs) are intended to warn personnel if mobile equipment moves within some preselected minimum distance of an energized overhead electrical power line. Two commercially available PWDs were tested at the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). The objective of the tests was to document performance capabilities and limitations for these PWDs by identifying factors that can influence their operation. The two PWDs evaluated in this research are the SIGALARM Model 210 marketed by Allied Safety Systems, LLC, and the ASE Model 2100 from Allied Safety Engineering. Both of these devices operate by measuring the electric field present around energized power lines. The PWDs were installed on a government-owned 22-st (20-mt) rough terrain crane. A purpose-built test site used for this research at PRL allowed operation of the crane near a variety of power line configurations operating at up to 25 kV. Most of the tests involved positioning the crane adjacent to one or more overhead power lines, adjusting sensitivities of the PWDs to alarm when the crane boom was approximately 20 ft (6.1 m) from the power lines, swinging the crane boom toward the lines under a wide variety of test conditions, and finally, for each unique set of test conditions, documenting the deviation from 20 ft (6.1 m) for actual alarm activation. Test results show that several factors can adversely affect PWD performance. PWD alarm accuracy generally deteriorated when operating with a boom position significantly different than that used for the device?s last sensitivity adjustment. Another factor that can affect PWD performance is configuration of the overhead power line(s) involved. Accuracy of alarm activa­tion distances was best for simple single-circuit installations, but degraded for multiple circuits on the same poles. This degradation was slightly greater for installations with different voltage levels and/or a combination of vertical and horizontal conductor arrangements. Performance also degraded for crane operation between two intersecting power line installations, especially for intersecting lines at different voltages. An additional aspect of power line configuration shown to influence PWD accuracy was phase sequence on the power line circuit(s). Specific phase con­ductor arrangements and combinations, particularly in multiple circuit installations, resulted in either improved or degraded accuracy.

Jan 1, 2008

By A. M. Muhamedilova, S. M. Narbekova, L. V. Semushkina, D. K. Turysbekov, N. K. Tussupbayev

The research and development of new, more selective collectors in order to improve flotation efficiency represent one of the main priorities in the development of innovative technologies pertaining to flotation separation of various substances and minerals. The use of collectors’ mixtures is considered as the universal instrument for ensuring necessary proportion of chemically and physically sorbed collecting reagents in every individual case. Currently hard-dressed, refractory ores and man-made raw materials, which are characterized by low content of valuable components, fine dissemination of mineral assemblages and similar technological properties of constituent minerals, are widely involved in the recycling processes. The possibility of processing tailings, which are left after flotation beneficiation, has been considered in the case study of tailings of the Zhezkazgan beneficiation plant and the Tishinsk copper ore deposit with utilization of the modified multifunctional flotation reagents. Modified poly-functional collector is the mixture of composite Aerofloat, TC-1000 and butyl xanthate. Reactants ratio is 1:1:3. The advantage of the suggested flotation reagents is that they are composed of two polar groups and have a long hydrocarbon radical. This structure, being in the water during flotation process, plays a dual role: first, as a collector adsorbing on the mineral surface it produces metal complexes with polar groups in the form of bridges; second, apolar radicals flocculate valuable slimed components, thereby intensifying flotation process. It has been shown that flotation of Zhezkazgan tailings with utilization of the lesser modified reagent amount compared to butyl xanthate has enabled to produce crude copper concentrate with 13.0 % copper grade and 80.22 %recovery. Compared to the baseline technology, copper content of crude concentrate has been increased by 5.1 % and the recovery by 31.4 %. It is shown that tailings flotation of the Tishinsky field by applying modified collector allows for increase of the of useful components extraction in a collective concentrate with: copper 9.63 %, lead for 8.41%, zinc 9.2 %, iron 2.73 %, gold 3.57 %.

Jan 1, 2018

By Zbigniew Lubosik, Andrzej Walentek, Stanislaw Prusek, Sylwester Rajwa, Aleksander Wrana

"Underground coal gasification (UCG) provides a solution to supply electricity from high ash coal or deep deposited seams. The coal is consumed in situ, and, accordingly, the ash is left underground. UCG could play a major role in the future of coal, which is expected to fuel 44% of the world’s energy in 2030, in a more environmentally friendly and commercially viable manner. Nevertheless, it is known that the UCG can impact the environment. One of the most important factors in safe UCG process should be the evaluation of rock mass quality and the monitoring of its behaviour. The changes of rock mass parameters and quality have an influence on numerous aspects, such as subsidence and the stability of underground workings in georeactor vicinity, however, they also increase the possibility of pollutant migration through fractures and pores. These issues are especially important in cases of gasification conducted in an operating mine or on areas of high ecological vulnerability. This paper details observations made in two underground trials of UCG performed in Poland recently. The first of which is the Experimental Mine Barbara (under the project entitled HUGE-2 Hydrogen oriented underground coal gasification for Europe – Environmental and Safety aspects, (Wiatowski et al., 2015). The other trial has been conducted at an operating mine, Wieczorek, which is in the framework of a research project on the development of coal gasification technology for highly efficient fuel and electricity production (Czaplicka-Kolarz et al., 2013). During these trials, investigations were carried out aimed at assessing geomechanical parameters of rock mass and support behaviour in surroundings of UCG geaoreactors. Investigation comprises assessment of geomechanical parameters of coal, floor and roof strata, roof displacements, and concrete support strength parameters variation, as well as standing steel support load. Hydraulic penetrometer, endoscopic camera, Schmidt hammer, pull-out method, telltale, and ground penetration radar (GPR) were used in the investigation. Research conducted at both EM Barbara and Wieczorek Collieries revealed that the UCG process did not adversely affected the competency of rock mass (expressed by number of fissures and strength parameters of rocks), the stability of roadways and the support performance in the areas located in the vicinity of the georeactors."

Jan 1, 2017

By M. Marchese

It is no secret that scarcity of fresh water is an issue that at a global level in the years to come will have a major impact on the business landscape. A number of projects, beyond the mining sector, could remain on paper only due to this. At the same time, this situation is seeing the rise of new business opportunities, such as development of technologies for more efficient usage of water, water recycling, and desalinization of sea water. Despite that most of Chilean mining facilities are located in the driest area of the world, business has developed strongly and actively for more than a century. However, the negative effect on the water reservoirs and the environment is, lately, resulting in the reduction of the authorized water rights. Holding Water Rights for any given volume does not guarantee that the resource will be available when needed. A recent report from the United Nations on global climate change indicates that global warming can be directly related to changes in the natural and human environment. Chile would not be an exception. The reduction in snow levels in the high Andes and reduced rainfall during the so called "Bolivian winter", have directly affected the replenishing of the underground water reservoirs in the lower parts of the valleys, where most of the extraction of the resource takes place. Mining facilities shall be designed to reduce potential environmental effects, using proven technologies, and considering the best practices available. These measures shall constitute a complete structural framework for the environmental impact assessment (EIA) of the Project. The measures to prevent and mitigate the impacts on the water resources shall be considered during the design stage of a mining project. Current and future mining projects in Chile are conscious that the increasing pressure on the limited water resources is becoming unsustainable, and are already facing the water scarcity and social pressure by implementing sea water desalination plants, including long pressurized pipelines to the mine sites (e.g. Escondida, Candelaria, El Morro, Regalito). This paper presents, in summary, an analysis of the present and potential future scenarios.

Jan 1, 2007

By F. Rudloff, C. Karageorgos, J. Moyo, I. Boadi, M. Struble, B. Lumsden

Over it’s more than 100-year history, the Kennecott operation has often been at the forefront of innovation; driven by the demands of the lower grade ore-body and the higher costs of operating in the US where wages are generally higher and regulation more restrictive. One way of reducing operating costs in c/lb is to increase the lbs produced at minimal cost. Despite the relatively coarse grind at Kennecott - about 30% >150μm, approximately 20% of the Cu lost to tail is liberated chalcopyrite in the <20μm fraction, and about 30%-40% in the <37μm fraction. In 2020 Kennecott undertook a detailed plant scale test of the magnetic aggregation technology to increase copper recovery by reducing fine copper losses. A paired statistical plant test of magnetic conditioning on one rougher line showed a 1.12% increase in Cu recovery to 97% statistical confidence. The next challenge, unforeseen at the start of the project, was the fabrication and transportation to site of the equipment for the three remaining rougher rows, during the severe supply-chain constraints of the Covid pandemic in 2021. This resulted in delays and unforeseen costs as world-wide transportation became chaotic, particularly transportation via west coast USA. Nevertheless, the project was completed and commissioned, with only minor delays and cost increases, due to a flexible approach to overcoming the hurdles encountered.

Feb 1, 2023

By S Lloyd, J Chow, S Fitzpatrick, D Greenup

The Tropicana deposit was discovered in 2005 after AngloGold Ashanti followed up an unexplained gold-in-soil anomaly. Discovered in a remote, barely-explored area of Western Australia not previously thought prospective for gold, Tropicana is the most significant gold find in Australia for more than a decade. The new, large scale open pit gold mining operation will produce an annual production of around 330 000 to 400 000 oz over a ten year mine life mining around 60 Mt/a.Process plant construction started in early 2012 and is due to finish in the December 2013 quarter. The mining contract was awarded to Macmahon Holdings (Macmahon) and mining commenced in July 2012 using conventional drill and blast, truck and excavator open cut methods.As a construction and start-up project in a greenfields location, the establishment of mining activities at Tropicana Gold Mine (TGM) involves the implementation of technical and operational systems, including the mining contract. Some of these systems and likely challenges were identified during earlier studies, while others were not foreseen until they were encountered. Alternatively, the time frames around implementation change depending on the changing knowledge of the project and industry environment. These systems include those common to the industry and those specific to the operation and location.This paper examines the implementation and development of a number of the systems specific to the establishment of mining operations, including the history, process and some outcomes. Although expected to be discrete systems to implement, they become interdependent. This linkage between systems further offers challenges and opportunities for the continuous progress of each system and for TGM as a whole.CITATION:Chow, J, Fitzpatrick, S, Greenup, D and Lloyd, S, 2013. Tropicana Gold Mine - mitigating the challenges of a mining start-up, in Proceedings World Gold 2013 , pp 51-60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Steve W. Ciccone

The Red Dog Mine is both the largest known zinc reserve and the largest zinc producer in the world. The mine started in 1989, and by 1999 had increased production from approximately 300,000 tonnes per year (t/yr) of zinc concentrate to in excess of 900,000 t/yr. The VIP Mill Optimization Project further increased zinc concentrate production to 1.1M t/yr while improving both product quality and zinc recovery. The Mill Optimization project also addressed a number of issues related to risk reduction: power generation capacity, water treatment capacity and concentrate thickening. The project was faced with numerous challenges, the most daunting of which was the schedule. This US$105M project was executed, from conception to completion, inside of two years. Less than nine months elapsed from concept to delivery of materials and equipment to site. The project also faced a 100-day icefree shipping window, the challenges of construction in an Arctic environment, and an extremely tight labour market for qualified craft personnel. These challenges were successfully addressed with several innovative approaches to project execution, including an Alliance contracting arrangement between the owner, engineer and contractor; full integration of the team; construction of modules in Anchorage; and fast-track engineering, procurement and construction. Steve Ciccone, AMEC?s project manager on the Mill Optimization project, works for the Mining & Metals unit of AMEC, a world leader in the provision of engineering and construction services. He obtained his BASc from the University of British Columbia and is currently midway through his MBA program at Simon Fraser University. Steve has 15 years of experience providing engineering and project management services on mining and metals projects, and has been involved in the execution of five capital projects and several studies at Red Dog since 1995. George Hope was responsible for process design and engineering on the Mill Optimization project and has been Manager, Project Development at Teck Cominco since 1995. Prior to this time, he was a project manager and chief metallurgist for Lac Minerals for 14 years and a mill superintendent and metallurgist for Noranda for 5 years. George received his BSc in Mineral Technology from the Royal School of Mines in England.

May 1, 2002

By G. A. Bezuidenhout, J. Davis, S. Lefume, J. P. T. Kapusta, D. K. Chibwe

"Although the centennial of the Peirce-Smith (PS) converting process has recently been celebrated, the technology has essentially not changed much since its inception. PS converting is used extensively in the Cu, Ni and PGM industry to remove iron and sulphur from a molten matte phase. A typical PS converting process would use low pressure air supplied by a blower to bubble air through the molten bath. This bubbling injection regime is inherently inefficient from a process and energy consideration. In the late 70’s and early 80’s, Brimacombe and co-workers demonstrated at both laboratory and plant scales that sonic injection (jetting regime) into copper or nickel converters could reduce or eliminate the above hindrances characteristic of PS converting. Since then, in spite of these successes, very little industrial applications have made headway in the converting process of non-ferrous metal mattes on a commercial scale. As part of its operational improvement and energy reduction program (process efficiency), Lonmin Platinum decided to conduct a full scale industrial evaluation of sonic injection using air only to establish if punchless, high efficiency sonic injection was feasible in its small 3.05 × 4.57 m converters (10’ × 15’). A plant trial was run for four weeks in one of its three converters. This paper discusses the plant demonstration with a focus on the experience acquired by Lonmin together with the key learnings from the trials. Reference will also be made to the commercial aspects of a full scale implementation of sonic injection in all three converters in the smelter. INTRODUCTION AND OBJECTIVESAlthough the centennial of the Peirce-Smith (PS) converting process has recently been celebrated (Peirce and Smith, 1909; Southwick, 2009), the technology has essentially not changed much since its inception. PS converting is used extensively in the Cu, Ni and PGM industry to remove iron and sulphur from a molten matte phase. A typical PS converting process would use low pressure air supplied by a blower to bubble air through the molten bath. This bubbling injection regime is inherently inefficient from a process and energy consideration."

Jan 1, 2012

By S. G. Kumar

The performance of nickel based high temperature materials is directly related to their microstructure, which is controlled by the various processing steps. Nickel base alloys are melted and refined by a variety of processes that include Vacuum Induction Melting (VIM), Vacuum Arc Remelting (VAR) and Electroslag Remelting (ESR). The limitation of VIM is that the metallrefractory reactions lead to the disintegration of the crucible and hence contamination of the product due to macrosegregation. This macrosegregation is alleviated to some extent by controlling the solidification in VAR. The main attraction of ESR is its ability to produce a clean product by controlling the deleterious inclusions. In recent years Electron Beam Melting (EBM) is emerging as an alternative to the VIM, VAR and ESR. This paper reviews the current status of these processes and outlines the scope for further improvements in the processing technology.

Jan 1, 1993

By Martin Landwehr

"Dust samplers are based on different principles. The konimeter is based on the number of particles counted; mining applications are based on routine sampling; and the photometrical evaluation of samples is used after the pre-separation of particles above 5 micron by the mining konimeter. In special cases, the Draeger sampler is used for quantitative analysis. General trends are toward larger samples, concentration on a weight basis, fractionation into size groups by different techniques and an analysis of composition. Standards or TLVs already exist in all industries. Surface industries base their criteria on concentrations and quartz contents in particles below 5 micron. The mining industry uses the tyndalloscope routinely to determine concentrations; concurrent] y, the rock content, as deter-mined by ashing samples, is obtained by konimeter.Threshold limits are related to the rock content in respirable fractions and tyndallometrically determined concentrations. The TL Vs are based empirically on Landwehr's ""dust values,"" as agreed upon with the Mines Inspectorates. Recently, and in accurate sampling, dust samplers have been used that count the dust in two fractions -above and below 5 microns. Mineral composition is determined either for all minerais or just for quartz. In assessing the dust hazard by Landwehr's ""dust values,"" all minerais are taken into consideration; in coal dust sampling, however, only the quartz content is taken into account. Efforts are now being made to co-ordinate the different assessment methods, arriving at uniform MAC values in agreement with those of other countries."

Jan 1, 1969

By H. Senoh

For the purpose of clarifying the reason caused a drastic decrease of discharge capacity for MmNi3.6Mn0.4Al0.3Co0.7 electrode at relatively low temperatures, various factors influencing the charge-discharge processes were investigated in the temperature range of 25°C to -40°C. The charge efficiency obviously decreased at low temperatures less than 0°C due to a decrease in the rate of the charge-transfer reaction on the electrode surface. Moreover, both the rate of the hydrogen diffusion from the alloy bulk to surface and the rate of the charge-transfer reaction significantly influenced the high-rate dischargeability. The addition of Mo to MmNi3.6Mn0.4Al0.3Co0.7 alloy was found to be effective for improving the electrocatalytic activity, leading to the improvements of the charge efficiency and the high-rate dischargeability at relatively low temperatures.

Jan 1, 2002

By M. Matabane, T. Khati

"Accurate delineation of the contact between a kimberlite pipe and country rock at production level depths is a challenge due to limited geological data. Geological information is obtained from widely spaced diamond core boreholes which are drilled either from surface or from higher mining levels within the pipe. Kimberlite pipe/country rock contacts are notoriously irregular and variable, further reducing the confidence in contact positions defined by the drill-holes. At Finsch Diamond Mine (FDM), the opportunity arose to further improve the confidence in the contact positions relative to the planned slot (end) positions of each sublevel cave tunnel during the development stage of these tunnels. As a result, the accuracy of the 3D geological model has improved.The use of diamond drill core for this purpose is expensive due to site establishment requirements. The lengthy time taken during site establishment also delays the development of tunnels and support cycles, thereby extending the completion dates. FDM has reduced delays during development by adopting percussion drilling, in conjunction with gamma ray logging. The S36 drill rig is mounted on a moveable platform and does not require a costly and lengthy site establishment. The holes are generally drilled (0°/flat) on grade elevation, and these holes could also be drilled from the rim tunnels (developed in waste) into the kimberlite pipe. A single-boom production drill rig is normally used to drill holes about 20 m in length.On completion of the contact delineation drilling, gamma logging of the holes is conducted using the GeoVista geophysical sonde (or probe) to log the natural gamma signature of the dolomite/ kimberlite contact. The advantage of this tool is that the readings are continuous within centimetre intervals, and due to contrasting characteristics between kimberlite (rich in clay minerals) and dolomite, the contact position can be determined accurately. The better definition of contact positions also adds value to tunnel stopping distance in terms of developing the tunnel’s slot at the optimum distance from the contact (easier blasting of longhole rings, avoidance of contact overbreak and premature waste ingress, and other matters relating to extraction of ore from these tunnels). This method is highly successful and has reduced development costs (on-time completion), improved definition of the pipe’s contact position for geological modelling, improved blast design, and mitigated early waste ingress by maintaining the contact’s integrity."

Feb 1, 2019

By Peter Waggitt

Northern Australia has been home to uranium mining for over 70 years, more or less continuously. In the early days, post World War 2, there was little effort made to remediate workings at the end of operations. The three “campaigns” of uranium mining (1951-55; 1960-70; and 1979-present) are all now in various stages of remediation. This includes not only the large legacy site at Rum Jungle but also smaller fields like the South Alligator Valley, as well as contemporary works at Nabarlek and the ongoing closure at Ranger– Australia’s longest operating uranium mine. This paper briefly describes some of the past remediation activities before providing an update on the Ranger closure programme and future timetable.

Jan 1, 2020

By GJ Hundman

The Multiple Unit Continuous Haulage (MUCH) System was designed to provide the capacity to continuously convey coal from the mining machine to the main haulage belt. The MUCH System has an operator who steers the lead vehicle, ever following the mining machine. All the remaining vehicles follow the path of the lead vehicle, with their conveyors automatically lining up between the lead vehicle and mine section panel belt. This is accomplished by mechanical linkages on the vehicles which are interconnected by steering bars between vehicles (patent pending). The MUCH System has an operator who steers the discharge vehicle when outby travel is required. Outby travel is just like inby, with each vehicle following the path of the preceding vehicle. Surface tests overwhelmingly indicate the "UCH System should track/retrack successfully in square pillar underground room and pillar coal mines with 18 ft. wide entries and slopes up to 10 percent. For 60 degree pillar plans the minimum entry width required is 15 ft. Surface tests also indicate the MUCH System will convey over 8 TPM of coal around 90 degree corners without excessive spillage.

Jan 1, 1983