Search Documents

By Matias Pentinnen, Wayne Dickinson

Electrowinning is a key process for copper production contributing roughly twenty percent globally and thirty to forty percent of production in the Americas1. Copper grade is assessed largely on deposit smoothness and on level of impurities in the metal. Smoothing aids are essential to create dense, low porosity deposits and guar has long been the material of choice for this purpose. Guar is, however, poorly stable under the strongly acidic electrowinning conditions, underlying ongoing research to identify an effective, acid-tolerant replacement. Current efficiency is also a critical factor in controlling copper production costs and chemical additives should ideally improve current efficiency as well as improving deposit smoothness.

Feb 1, 2025

By G. Vibert Douglas

THE prospecter and geologist in the field, in the search for gold, are very often faced with a real difficulty. The: mineralized rock _frequently contains gold which is so finely divided or associated with sulphides that it is not recognizable in the gold pan. In recent years, the practice has been to take samples, send them to an assay office, and sit down and wait for results. This paper describes a method of solving the difficulty of proving the presence of this fine gold. The investigation is still in an experimental stage; but certain results have been obtained which would seem to justify publication. We do not consider that the method outlined is quantitative, but we believe that qualitative results are assured. The procedure has the great merit of simplicity. A sample of approximately two pounds of the mineralized rock should be taken and powdered as fine as is practicable. This powder is theo panned and the heavy minerals concentrated. Approximately two grams of these concentrates are taken for the test (one gram can be roughly gauged in the field by heaping up the powder on a Canadian twenty-five cent piece). The material is placed in a test-tube and 6 c.c. of a 10 per cent solution of iodine in alcohol are added (one-third of a test-tube full is approximately equal to 6 c.c.). Heat gently for about ten minutes over a spirit lamp, but without actual boiling. Allow to stand undisturbed until the sediment has settled to the bottom. Remove the clear iodine solution with an eye dropper. Allow it to fall, drop after drop, on a warmed pyrex watch-glass (the drops should be of equal size), taking care that the successive drops fall in the same place and that each drop evaporates before the next drop falls. Heat is applied to the lower side of the watch-glass by means of a spirit lamp. If gold is present in amounts of $2.00 or more per ton, a gold mirror will be formed on the watch-glass. This process of dropping and evaporating should be continued until no clear solution remains. If no mirror has appeared when all the solution has been used, another 6 c.c. of the iodine solution should be added to the powder and the process repeated. The absence of a mirror after the double treatment denotes an amount of gold less than two dollars per ton at the present price, or that the ore contains no gold. The mirror obtained must be washed with nitric acid ( 1: 1) to remove any copper, silver, lead, zinc, and iron. The yellow mirror remaining is pure gold.

Jan 1, 1937

Study on Ball Mill Grinding of a Cassiterite-Polymetallic Sulfide Ore

Sep 13, 2010

By N. M. S. Balbinot, A. L. Rodríguez, C. M. Mahlmann, R. de C. de S. Schneider

The use of sunflower oil co-products it was studied for production thermoplastic composites. Thermoplastic composites have been processed in polyethylene matrices of virgin linear low density polyethylene (LLDP) or recycled. Samples have been formulated with 10% mass fraction of sunflower bran, seed coat and mixture of bran and seed coat. The material characterization has been achieved by mechanical tensile test and Shore D hardness and by density physical testing. The results have demonstrated better properties to thermoplastic composites with sunflower seed coat.

Jan 1, 2008

By Jon A. Hummer, MICHAEL R. SHAHAN, Aleksandar D. Bugarski, Shawn Vanderslice

Occupational exposures to respirable dust and submicrometer aerosols emitted by diesel-powered equipment are a health concern for underground mining operators and regulators. A study was conducted in an underground mine with the objective to identify, characterize and source apportion airborne aerosols at the setup face and recovery room during longwall move operations. 

Jan 1, 1923

Jan 1, 1923

By H. H. Murray

New and improved benefication techniques are available to allow the production of clay minerals of exceptionally high purity. This is particularly true for kaolins and smectites. Wet processing techniques including particle size separation, high intensity magnetic separation, chemical leaching, flotation, and selective flocculation are described and results and applications are discussed. The blending of clay minerals with other minerals provide opportunites to make special ceramic materials such as cordierite and other minerals which have very special ceramic properties including low heat expansion, high fired strength, low absorption, and other desired qualities.

Jan 1, 1989

By J Eberhard, C Paton, J Bennett, C Baillie, A Melland, J F. Clewett, T Newsome

A central aim of rehabilitation is to ensure that disturbed land is returned to a post-mine condition that is safe, stable and self-sustaining. This paper describes initial results from a grazing trial at the New Acland open-cut coal mine in southern Queensland (-27.27 lat, 151.72 long) that aims to assess the sustainability and viability of cattle production from rehabilitated mined land compared to production from surrounding unmined lands (Newsome 2014). The grazing trial was established in 2013 by the Acland Pastoral Company, a subsidiary of New Hope Coal, on lands previously used for dairying, beef and crops before open cut coal mining of the Walloon coal measures began in 2002. The area has a mean annual rainfall of 640 mm. Local soils, typically dermosols and vertosols derived from sandstones or overlying basalt flows, are suited to grazing but are marginal for cropping.CITATION:Clewett, J F, Newsome, T, Paton, C, Bennett, J, Melland, A, Eberhard, J and Baillie, C, 2018. Sustainable production from rehabilitated coal mine pastures in southern Queensland’s Brigalow Region – Acland grazing trial results, in Proceedings Life-of-Mine 2018, pp 35–37 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By A E. Levett, J Durbin

The environmental, social and governance (ESG) obligations of mining companies promote the consideration of water and land resources as well as the post-mining employment opportunities following the cessation of mining operations. This work aims to outline the potential for a mining operation to use their brackish mine water resources to support microalgae production, generating high-quality organic carbon sources to support their mine rehabilitation and closure outcomes. Microalgae production is an established commercial process for high-value products including vitamins, cosmetics and food supplements. On mine sites, microalgae production offers several major environmental and social opportunities: (i) carbon capture, (ii) metalliferous water treatment, (iii) acid mine drainage prevention, (iv) beneficial reuse of brackish mine water, (v) accelerated soil formation and (vi) post-mining employment (Levett et al, 2023).

Aug 2, 2023

By N. S. Dalal, B. Jafari, F. Y. H. Green, V. Vallyathan

"Using electron spin resonance (ESR) spectroscopy we have carried out a systematic study of the measurement of concentrations of organic free radicals in freeze-dried lung tissue. Sixty-six tissue samples were obtained from the National Coal Workers' Autopsy Study (NCWAS). The samples were characterized in terms of the concentration per gram of the free radicals, and examined in relationship to the histopathological parameters such as age, numbers of years in the mining atmosphere, the degree of disease, and smoking history. Preliminary results indicate a positive correlation between the free radicals in the lung tissue and the severity of pneumoconiosis.IntroductionThis paper summarizes our electron spin resonance (ESR) measurements of the concentration of organic free radicals in the freeze-dried lung tissue of autopsied coal miners. This work was undertaken because it is well known that most coals contain carbon-centered organic free radi¬cals,(1,2) and recent studies from our laboratories indicated that reactive free radicals might play a role in the biochemi¬cal mechanism of coal workers' pneumoconiosis (CWP) (3) Thus we obtained 144 lung-tissue samples from the Nation¬al Institute for Occupational Safety and Health (NIOSH) in Morgantown. The samples came from the data bank of the National Coal Workers' Autopsy Study (NCWAS). This selection was unique because fairly detailed histopathologi¬cal information was available for each sample.Other recent studies in this field are those of Ohta et al (4) who conducted ESR measurements on black dust deposited in autopsied human lungs, but no coal miner was included therein. Earlier Retcofsky (2) had examined one lung-tissue sample via ESR spectroscopy and had concluded that the free radicals in the lung tissue reflected simply the fusain (narrow component) ESR signals. The present study was thus undertaken to complement the earlier work (2-4) and the results indicate a positive correlation with the disease severity fairly strongly."

Mar 1, 1989

By Joseph W. Horne

This report presents the results of an investigation by the U. S. Bureau of Mines in cooperation with the State of Colorado, on the yields and properties of oils produced from oil shale, lignite and subbituminous coal using the standard assay method developed by the Bureau for oil-shale testing,. The purpose of this work, which is part of the general study of oil shales being conducted by the Bureau of Mines and cooperating agencies, was to obtain information on the amount and character of the yield of crude oil or tar from different typical oil shales, the yield of light oil or naptha that might be suitable for use in motor fuels, and other products of shale oil. As the west has large resources both of oil shale and low-grade non-coking coals, it is of interest to know the relative yields of tars, light oils, and combustible gases that can be produced from these coals when retorted under conditions similar to those suited for oil-shale retorting. Source of Samples The coal samples were obtained from deposits on or adjacent to the public lands in the States of the Rocky Mountain region. Many of the mines sampled are operating under Government leases or permits. The number of coal samples secured from the various states are: Colorado, 6; Montana, 9; north Dakota, 6; New Mexico. 1; South Dakota, 1; Wyoming, 9. Of these samples, 14 were lignite coal, 16 subbituminous coal, and a bituminous coal. The standard channel method of the Bureau of Mines was used for sampling. Coal samples received at the Boulder Office weighed about twelve pounds each, and duplicate samples were sent to the Pittsburgh Station for proximate and ultimate analyses. The origin of the samples and description of the deposits are given in Table 1.

Jan 1, 1927

Reduce longwall shearer operator's dust exposure by selecting the best drum water spray sys-tem for minimizing dust generated durinq cutting. Approach Three of the most commonly-used drum water spray systems were installed on the same set of shearer drums and compared to determine which system best suppresses dust. The spray systems studied were: ? pick-point flushing ? cavity filling ? water-through-the-it Instantaneous and gravimetric sampling instruments were used to measure the respirable dust exposures of the shearer operators and dust concentrations downwind of the shearer. The Three Systems: Longwall shearer drums are routinely equipped with internal drum spray systems since these systems have been shown to be more efficient than external systems in terms of dust suppression per gallon of water applied. All U.S. longwall shearer faces utilize some type of internal water delivery spray system. The two most common systems are bit-or pick-point flushing and cavity filling. Pick-point flushing uses nozzles mounted in the bit blocks or in special blocks immediately in front of the bits. Cavity filling utilizes spray nozzles installed in a pipe manifold mounted on the drum hub between the scrolls or along the edge of the vane scrolls; water is sprayed radially from the manifold towards the adjacent vane scroll.

Jan 1, 1986

Theo. B. ComstocK, Los Angeles, Cal. (communication to the Secretary*):—Mr. Blake's recent paper upon this topic undoubtedly partly explains the rationale of a part of the known facts bearing upon discolorat'ion and encrustation of rocks. His quotation from Humboldt, with reference to certain South American examples, may be questioned in the light of further facts, which do not appear to bear out the great traveler's theory of causation. There is no available evidence that the waters of the tropical rivers referred to by Professor Blake contain dissolved organic matter in the varying proportions required to demonstrate Humboldt's guess, nor do the concomitant facts in any manner bear out the hypothesis that the blackening in one case and its absence in the other may, perhaps, be traced to differences in the chemical reactions of the respective waters. Careful consideration of Professor Blake's illustrations, in connection with numerous personal observations extending over widely-scattered areas, convinces me that elements of

Jan 1, 1905

By H. E. Nold

THIS paper is an effort to explain in a simple manner the fundamental principles involved in examining a clay deposit for both quantity and quality and in operating a clay mine, either open-pit or underground, SO that the best quality of finished material can be made from the raw material available. The writer is aware that what is recommended in this paper is everyday practice in many refractories plants and in some other heavy-clay products plants, but observations made while visiting practically every clay mine in Ohio have convinced him that the practices herein discussed are not as widely used as their importance warrants. It is true that the problem of mining for quality is more acute in refractories plants than in most heavy-clay products plants, yet some of the latter are finding it profitable to pay more than ordinary attention to the selection and blending of their raw materials. It is hoped that this short paper may prove helpful to some who are now finding it difficult to produce a uniform product of as high quality as their clay deposit seems to warrant. The coordination of the work of the clay mine or pit with the manufacturing plant, to the end that the best product possible be made from the raw material available, presupposes a rather intimate knowledge of the clay deposit. The knowledge must include not only information of the amount of clay available but also rather detailed information about both vertical and horizontal variations in quality of the clay. This information should cover three things: quality, quantity, and location. Sampling Undeveloped Deposits In the case of an undeveloped deposit with a shallow overburden, pitting may be the cheapest way of testing. For thick deposits or deposits with rather heavy overburden, the diamond drill, using a double core barrel, offers the best means of testing. When using the diamond drill in clay testing, it is doubtful whether it pays to take less than 2-in. cores; it is difficult to get complete cores with smaller drills, and the quantity of material obtained with smaller cores is not sufficient for the necessary tests.

Jan 1, 1929

By Yong Pan, SRIVATSAN JAYARAMAN SRIDHARAN, Purushotham Tukkaraja

The block cave mining method poses unique ventilation challenges compared to other underground metal mining methods. This research study focuses on assessing the airflow behavior in regulated airflow distribution systems by developing a 1:100 scaled block cave experimental model and a numerical model. This study also investigated gas flow behavior under various airflow conditions. Based on our findings, we observed that reduction in particle size and porosity of caved materials, decrease in cave footprint, and closure of undercut drifts would increase cave airflow resistance. The increased airflow is found to be beneficial for gas dilution regardless of its source locations, while the regulated airflow distribution system might deteriorate the gas dilution situation when the source is located in the extraction drifts.

Sep 1, 2022

By K. Kim

"All milling operations would like to achieve the best possible recovery in combination with the highest achievable throughput. Unfortunately, many operations have problems with low recovery, low throughput or both. In the majority of these cases investigated by the author, the solutions to improve recovery and throughput were simple. The solutions did not include implementation of new technology or major capital, but rather a return to fundamentals. In most cases, problems occurred because the operation was not following their own operating procedures, because the design of the circuit was changed without adequate change management or understanding of the implications of changes, or because basic metallurgical measurements and control were not taken or ignored. In this paper, examples of these problems and their solutions derived from long and varied experience will be discussed. The objective of this presentation is to provide the milling operator with practical and readily implementable solutions to common milling issues to improve throughput and recovery.INTRODUCTION Mill operations can be evaluated by many operating parameters, but the two best indicators are recovery and throughput. These two parameters summarize the wellbeing of an operation. The grade to the mill is also a good indicator, but this is usually controlled by the mine. The best recovery and throughput are achieved through a team work involving operators, maintenance workers and metallurgical staff. The milling operations include many unit operations, such as crushing, grinding, flotation, leaching, carbon in leach, Merrill Crowe, roaster, autoclave and refinery. The tools available to the operations are plant design, process measurements, assays, metallurgical balance, and operating strategy. Twelve real life examples of improvements of recovery and throughput are presented in this paper. EXAMPLE 1: CRUSHING CIRCUIT WITHOUT FINE ORE BIN At this operation plant throughput could not be maintained at a high rate because feed to the mill became coarse during the day. The cone crusher was feeding the ball mill directly. As the day wore on, the gap on the cone crusher would slowly increase, which would cause the product size to increase. This would increase the re-circulating load on the ball mill. The throughput would decrease accordingly. Furthermore, the throughput would decrease more with high frequency of maintenance on the cone crusher."

Jan 1, 2019

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Cu and Zn-0.12 pct Ti-Cu alloys with various copper additions to 1.25 pct. The alloys were rolled cold and at various hot-rolling temperatures to reductions as high as 92 pct after breakdown rolling. The properties are extremely sensitive to various combinations of composition, rolling temperature, and rolling reduction, Zn-Cu alloys can develop good creep resistance, but they are inferior in that respect to Zn-Ti-Cu alloys. For alloys either with or without the titanium addition, cold-rolling results in recrystallization of the matrix and rejection of copper from solution, causing poor hardness, tensile, and creep properties, but high ductility. Peak tensile strengths develop when the alloys are rolled in the range 320° to 400° F, Best creep resistance for Zn-Cu alloys requires higher rolling temperatures when copper content is increased. Creep resistance is best for Zn-Ti-Cu alloys with about 0.75 to 1.0 pct CU rolled near 480° F. Some copper is soluble in the TiZn15 phase, which forms into "stringers" during rolling. The possible contributions to creep behavior of factors such as distribution of second-phase particles, grain size, and preferred orientation are discussed.

Jan 1, 1970

By G. I. Gritsko

In this paper we consider the elements of a distributed information geomechanic monitoring system which is used in computerized mine planning and mining operations control. The automated system is a technical means of geomechanic monitoring, as a complex system of regulated observations, estimation and prediction of geomechanic state of rock mass and workings during underground mining of coal deposits. Geomechanic monitoring at coal mines and the automated system execute data collection, analysis and calculations of geomechanic situation in the panel during planning, development and carrying-out of mining operations for ensuring geotechnical stability of underground mining.

Jan 1, 1996

Characterizing coal mine roof rock is extremely important for hazard assessment, reinforcement, and entry design. The Coal Mine Roof Rating (CMRR) is an innovative rock mass classification that has found acceptance in the coal mining industry. A disadvantage of the original CMRR is that it cannot be determined in advance of mining, because it requires underground observations. An entirely new set of procedures have now been developed to determine the CMRR from exploratory drill core, as described in this paper. The new procedures employ Point Load Tests (PLT) to determine strength parameters that account for approximately 60% of the rating. Both diametral (parallel to bedding) and axial (perpendicular to bedding) PLT are conducted. The diametral tests allow estimates of bedding plane cohesion and rock anisotropy, both of which are critical to estimating susceptibility to horizontal stress. Traditional core logging procedures are used to determine discontinuity spacing and roughness. To ensure compatibility with the original CMRR, the new rating scales were verified by comparing drill core results with nearby underground exposures. To assist mine planners in using the new CMRR procedures, a large database of strength ratings of roof rocks was assembled through extensive point load testing and logging. Over 2000 point load tests (both axial and diametral) have been made on 30 common coal measure rock types from mines representing most U.S. coalfields. This database has been merged with the popular core rating system of J.C. Ferm into a field guide for geologists and engineers. By using the pictorial classification system of Ferm to identify the rock, typical CMRR can be compared with values calculated using the new CMRR procedures.

Jan 1, 1996