Search Documents

By Jinrong (Patrick) Mang

Three of the most challenging problems in phosphate beneficiation are discussed: flotation efficiency, resource conservation and environmental impact. Some new flotation machines offer the opportunity of reducing power and reagent consumption significantly, while increasing specific capacity many fold. Efficiency might also be improved dramatically by replacing the "double float" process with a single-collector scheme. Model based software control is a powerful tool for improving overall plant efficiency. Recovery of phosphate values from the phosphatic clays could extend phosphorus reserve life significantly. phosphate recovery from the slimes might be achieved by sizing-flotation, selective flocculation and bioleaching. Reducing the volume of phosphatic clays produced is another key stop to minimizing phoephate logs. Such a reduction may be realized by floating at finer cut size. Although an ideal' dolomite separation process is yet to be developed, a cationic flotation process may prove to 'be economically feasible. Loss of phosphate in the desliming stage is the major problem with most of the flotation schemes for removing dolomite.

Jan 1, 1995

By L McCallum, G Dale, B Silverwood, T Roscoe, A Costin

The introduction of Progressive Closure and Rehabilitation Plans (PCRPs) in Queensland from 2019 places greater importance on planning and implementation of mine rehabilitation activities. The progress and outcomes of progressive rehabilitation activities is monitored and reported upon to demonstrate success in achieving progress towards the approved post-mining landform, and to inform corrective action where required. The requirements of PCRPs place additional emphasis on mine sites to quantify the risks of successfully achieving planned outcomes. This is particularly challenging given mined-land rehabilitation is a complex process involving decisions on multiple inter-acting management interventions, climatic conditions and spatially variable site characteristics.

Aug 2, 2023

By Enrique Rubio Esquivel, Matías Fuentes Bustamante

The transition from open pit to underground mining represents a key strategic challenge in modern mine planning. This paper presents a multicriteria and multivariable methodology to plan such a transition, integrating technical, economic, environmental, and social considerations. The proposed framework focuses on risk reduction (de-risking) through the identification of alternative development paths, the use of stochastic simulation to model geological and technical uncertainty, and different mining strategies such as methods, production rates, sequence, etc. for ultimate underground implementation. The study summarizes the limitations of traditional planning methods—which usually treat the open pit and underground mine designs as independent processes—, also often it considers a single mining method and production rate for the underground option. Instead it is proposed an integrated approach that leverages synergies between both mining methods and scalable production rates. Also the proposed methodology incorporates the definition of critical variables (geotechnical, economic, and social, among others), the construction of multiple operational and technological transition paths, and the evaluation of each path under criteria of economic attractiveness and practical do-ability (capacity to be executed). Using simulation tools (SIMPLAN for operational performance and SIMVAL for economic evaluation), probabilistic distributions of the different path are obtained, enabling the quantification of the project’s Value at Risk (VaR). A subsequent multicriteria analysis weights the expected profitability against the feasibility of execution of each alternative, producing a decision matrix that provides a framework for evaluating the different project path. As a result, the proposed approach identifies OP→UG transition strategies that maximize business value by capturing remaining resources while minimizing financial and operational risks. Finally, strategic conclusions and recommendations for the industry are provided, emphasizing the importance of early transition planning even challenging the open pit sequencing of the latest push backs by introducing early underground operations. Future work includes strengthening the methodology—such as integrating real-time analysis and adaptive decision-making—and providing recommendations for its application in various mining operations. In summary, this paper delivers a technical and professional framework to guide mining companies on when and how to carry out a successful transition from open pit to underground mining, balancing resource recovery with financial, operational, and social security.

Feb 22, 2026

By A. Noble

"Linear circuit analysis (LCA) is a fundamental tool that may be used to evaluate, design and improve the performance of mineral separation. The traditional LCA methodology provides a comparative evaluation of circuit designs purely from the unit interconnections. The quantitative approach uses the analytical circuit solution to evaluate the slope of the circuit’s partition curve at the midpoint. Since the partition slope is often associated with a separation’s general selectivity, this numeric value is used to compare and rank alternative configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. By itself, this value does not account for the relatively high unit dollar value of pure material or the gains and losses in mass yield associated with alternative circuit configurations. Realizing the value in the LCA methodology, but respecting the limitations of the partition slope valuation, the authors have derived two new performance indicators that quantitatively address pure particle misplacement (the Partition Moment of Inertia) and circuit mass yield (the Yield Score). Together, these parameters provide a better indication of separation economics in typical mineral and coal separation systems. Since the two parameters provide independent information on circuit selectivity and circuit yield, a Pareto efficiency, multi-objective function selection approach is proposed for preliminary circuit selection.IntroductionOver the past 30 years, numerous scientific and industrial studies have proposed various mineral processing circuit design methodologies that attempt to optimize the allocation of separation resources within the processing plant. Over this period, the methodologies have undergone various transitions, including the increased inclusion of process models and computationally intensive algorithms, as well as a general shift from a purely technical solution (Lauder and McKee, 1986) to partially economic solutions (Abu-Ali and Sabour, 2003; Cisternas et al., 2014). Today, circuit design is largely driven by flowsheet simulation; however, no consistent design methodology is used across the industry.One intriguing approach for circuit evaluation is linear circuit analysis (Meloy, 1983a). This method evaluates the separation potential of the circuit solely considering the unit configuration and stream interconnections. No preliminary data other than the basic circuit configuration is required to use the approach."

Jan 1, 2015

By Gill Montgomery

This report covers operations at the Crystal-Victory and Minerva No. 1 mines in Hardin County, Ill., which are operated by the Minerva Oil Co., Fluorspar Division, with offices in Eldorado. It describes the exploration, development, and mining practices, giving costs of each. Transportation, equipment, power, labor, and other influencing factors also are discussed. The mining methods employed are those most applicable to the flat-bedded replacement deposits common to the Cave-in-Rock section of the Southern Illinois fluorspar district. The fluorspar beds occur from surface exposures to 1,000 feet deep. In this district churn drilling is the method practiced for exploring flat-bedded deposits from the surface. Aerial photography and geochemical methods for indicating mineralization have been helpful in planning a drilling program. A program usually includes enough drilling to obtain only sufficient data on the value of the ore body and its structure to justify initial development and purchase of the mineral rights under option.

Jan 1, 1960

By N. Mizutani, S. Harada, Z. Asaki, T. Tanabe

"The development of lead-free solders is urgent in view of environmental standpoints. In this -work the wettability of tin-bismuth- silver solders on copper was studied. Three kinds of fluxes were used. The wettability of conventional eutectic tin-lead .solder exhibited an excellent level over the other solders of tin-bismuth systems. Poor wettability of the tin-bismuth solders may be caused by the growth or dendritic copper-tin compounds at copper/solder interface, in contrast to the case of tin-lead'· solder. The wettability was improved by the addition· of silver in the solder. In this tin bismuth- silver system, silver was abnormally concentrated at the copper I solder interface even in the initial stage of contact. The wettability of the solder and the thickness of compound formed on the copper have a good correlation; the solder containing 2% silver exhibited the best wettability and the formation rate of copper-tin· compound on the copper was slowest.IntroductionSocial demand to avoid lead use in the industrial fields has been recently promoted· (1) because of the environmental protection of water resources. Especially the lead-bearing solders have been widely used in electronics and automobile products, and it is urgent to replace them with nontoxic materials (2)-(4). Thus the development of lead-free solders becomes an indispensable subject to the new generations and many works (5)(6) have already been carried out on the research and development of new solders. New lead-free solders are expected to have some requirements, for example, moderate melting temperature, proper strength and integrity, and lower prices, as compared with conventional solders. There have been already several alloy systems developed. Among ·these alloy systems, tin-bismuth binary or tin-bismuth-silver ternary alloys have great advantages such as having a wide range of soldering .temperature by controlling con:ipositions, though they have such disadvantages as ""lift-off"" (7)-(9): It is said, on the other hand, that a frequently overlooked property of solders, or one that is typically ignored by the research scientist as an ""issue"" for the manufacturing or product engineer, is wettability (10), although a ·work on the wettability has recently been published (11). In this Work, therefore, the authors selected Sn-Bi-Ag solders and focused mi the effect of Ag-addition to wettability of the solder."

Jan 1, 2000

By J A. de la Torre, I R. Cerna, G K. Karadjian

The La Colorada underground mine in Zacatecas, Mexico is a mechanised cut-and-fill silver mine with a capacity of 1250 t/d. The project focused on training the mine’s experienced operators for a fleet of underground trucks, through the use of a training simulator. The project was run by the simulator vendor, in collaboration with the mine’s maintenance, safety and production management.A training program was created targeting maintenance reduction, productivity improvement and increased utilisation and availability. Operators were first acclimatised to the simulated environment, had their current performance baselined, then received targeted coaching, with the process repeated to reinforce learnings. Concurrently, production, maintenance, and safety data was being measured in the real world to measure skills transfer. Due to limited telemetry available from the equipment, many of the data points for the project were sourced from maintenance logs, and accounting data.Equipment failure data measured from unscheduled maintenance records showed an overall 6.5 per cent decrease in unscheduled maintenance following the implementation of the training program. This rate of reduction correlated with the significant decrease in equipment abuse behaviours measured within the simulator during this period. Additionally, overall maintenance activities showed a significant decrease, confirming that reductions in unscheduled maintenance were not achieved through increases in scheduled maintenance. The reduction in equipment damage also increased availability and utilisation of the truck fleet. This highlights that the maintenance improvements not only reduced maintenance costs, but made the fleet available for more production. Moreover, the variability of the operator performance was decreased by 86 per cent, and the difference between their best operator and the worst is less than the baseline; this showed a gap where machine abuse, productivity and cost are impacted directly.This project illustrated that even small-scale mining operations with an experienced operator workforce can achieve positive return on investment (ROI) from simulation-based training. It also highlights that in the absence of equipment telemetry, alternative data sources such as accounting data and maintenance logs can be used to quantify ROI from training.CITATION:Karadjian, G K, de la Torre, J A and Cerna, I R, 2017. Innovations in underground hard rock operator efficiency – through simulation-based training technologies and processes, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 53–58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Lincoln A. Stewart, P. S. Haury

"INTRODUCTION AND RESUME Arizona asbestos mines are the only sources on the American continents of iron-free chrysotile spinning fiber that meets the Navy specifications for asbestos fiber for use in covering electrical cables. Rhodesia normally supplies the bulk of this grade of asbestos at about half the Price of Ari zona spinning fiber. The acute submarine menace in 1942 focused attention on the danger that imports might be cut off and that a sudden demand for greatly expanded production might fall on the Arizona mines to supply the tonnage of this essential material needed for war production.A joint preliminary investigation of Arizona asbestos deposits was made in August 1941 by J. R. Thoenen, senior mining engineer of the Bureau of Mines and A. E. Granger, a geologist of the United States Geological Survey. A more extended investigation of the numerous asbestos mines and prospects, which are scattered over 25 townships of difficult terrain in Gila County, was begun by the senior author in August 1942.The Geological Survey assigned two geologists (Newton Chute and A. F. Shride) a few weeks later to study the geology as an aid in selecting the mines for the Bureau's exploration projects. Six mines were selected for exploratory work because it was desired to prove reserves of ore where production could be started quickly if urgent demand should arise. Acceleration of production is normally slow because of adverse operating conditions. First, the mines are at distances of 35 to 100 miles from Globe, the shipping and supply point, and the roads are few and poor. The mine openings start in steep canyon walls, so that mining supplies usually have to be packed in and the product packed out over 0.5 to 5 miles of burro trail. Second, most of the ore deposits are small, and the ratio of rock broken to spinning fiber recovered is very high, usually exceeding 200."

Aug 1, 1947

By J. L. Kearns

The importance of optimizing equipment replacement decisions becomes more critical each year due to the rising costs of buying new equipment versus maintaining old equipment. Replacing equipment when it is physically worn out, or replacing it too soon or too late relative to its Economic Life (when it is economically worn out), is very costly. After extensive literature review and research, Kennecott has developed its Equipment Replacement Guide (ERG) system which identifies, evaluates, and justifies the replacement of uneconomical equipment. The system considers such critical factors as inflation, decreasing work capability, increasing maintenance/repair and operating costs, taxes, time value of money, return on investment, salvage value, and investment tax credit. These factors are used in a system of equations which balance the costs of new equipment against the total operating costs of old equipment. The solution of the equations determines the Economic Life of equipment. Replacement of equipment at the determined Economic Life will earn the specified, required return on investment that is used in the calculation of the Economic Life.

Jan 1, 1979

By Arne Landsberg

The Bureau of Mines measured the vapor pressure of FeC12 , FeBr2, FeI2, Sb, Bi, Cd, Mg, Pb, FeC13 , and VCl2 using the Knudsen-and torsion-effusion methods, and on FeC13 -NaC1 mixtures, Au2Cl6, and MgNi2 using only the Knudsen method. Apparent vapor pressures calculated from the experimental data vary with orifice size and method of determination. Reaction with residual oxygen in the instruments was noted to have an effect on the iron halide data. Vapor pressure curves plotted as log P versus 1/T (where P is pressure and T is absolute temperature) for one substance using several orifice sizes tended to converge at a single point when extrapolated beyond the experimental region. All of the data, except those of VC12, agree with previously published results. The importance of comparing effusion measurements with those obtained by other methods and the variations encountered with various orifice sizes are discussed.

Jan 1, 1977

By Charles F. Jackson

Waste filling has been employed for many years for supporting the walls of stopes and preventing failure and subsidence of the surrounding and overlying rock formations, and its effectiveness for this purpose has long been recognized. It is used for permanent support in ground where timbering (including square-setting) is inadequate for more than temporarily supporting the walls of the excavations. It should be rioted, however, that effective as a good, solid fill may be in resisting heavy side pressure and direct weight, its usefulness for supporting large areas of back and preventing breaking and movement of the overlying rocks is limited. Even the strongest and most uniform rocks will break if the unsupported span becomes too great; and since filling cannot be packed tightly against a horizontal back there is always a possibility of the back breaking and consequent subsidence if the maximum self-supporting span is exceeded. Planes of separation, such as bedding and fault planes, slips, and joints, are common in all rock masses; these may occur above the stoping area where their presence cannot be ascertained by observation. If too much reliance is placed upon filling for the support of a large horizontal area of back (as contrasted to support of vertical or steeply inclined walls) large masses of rock may break along a. plane of weakness, compress the fill, and leave an open space into which caving of the overlying rocks may continue until the space is filled. In this paper the term "waste filling" includes any filling material other than ore - waste mine rock, rock from surface quarries or opencuts, sand and gravel, mill sands, or slags from smelting operations.

Jan 1, 1935

By Ch. D. Taylor

Past studies with blowing face ventilation systems have shown that using a machine-mounted scrubber and water sprays can reduced methane levels at the face. The current research was conducted to determine how the sprays and scrubber interact to reduce methane levels, and what spray configurations provide the best face ventilation when used with a scrubber. Testing was conducted in a ventilation test gallery designed to simulate a full-scale mine entry. In the entry, a model mining machine, equipped with a simulated dust scrubber and water spray systems, was located at the face of a 6.1 m (20 ft) box cut. Face ventilation was provided by a blowing curtain located 12.2 m (40 ft) from the face. Methane released from a manifold at the face was measured at six locations near the face to compare the ventilation effectiveness of the spray systems while operating with and without the scrubber. Airflow movement across the face was affected by the spray configuration and scrubber operation. Average face concentrations were lowest when directed sprays were used with the scrubber. Varying the direction of the scrubber exhaust affected face methane levels.

By Aris Tambunan, Nella Lubis, Nurafrianti Saala, Komang Widhiayanto, Herry Saputra, Rudolf Sitorus

Maximizing mining recovery rates and minimizing ore loss are pivotal objectives for economic efficiency and operational effectiveness. This study explores methods to address these imperatives by enhancing ore production and recovery through improved blasting techniques and spillage control in the Martabe Gold Mine Project in North Sumatra Province, Indonesia. Between 2018 and 2021, the average mining recovery rate stood at 93%, resulting in a potential annual ore loss of 7% and a potential quarterly financial impact of close to $2 million. Maintaining and enhancing mining recovery became crucial, with a planned 30% increase in total material movement for 2022. The mining recovery target for 2022 was set at 96% based on best achievement historical data from 2021 to increase ore tonnage by 203 KTon per annum. To achieve the primary objective of increasing ore production by improving mining recovery, the study focused on predicting and controlling the movement of blasted ore to reduce spillage and enhancing the grade control model to reflect actual conditions post-blasting. Several alternative solutions were explored, primarily emphasizing drilling and blasting activities. Essential methods included capturing the actual blasting movement to adjust the ore block based on blasting design data and post-blasting muckpile topography. This approach minimizes ore loss by providing output as ore block adjustment based on post-blast movement data. In addition, the tie-up design was adjusted to control ore spillage outside the pit ridge. The implementation of these methods yielded significant improvements. Adjusting the ore block based on actual blasting movement contributed $1,545,764 in benefits. Controlling ore spillage outside the pit ridge achieved a 10% reduction in spillage, contributing $79,184 in benefits. These enhancements successfully met the 2022 mining recovery target of 96%, marking a 3% increase from 2021. Consequently, ore loss was reduced by 178 KTon throughout 2022, resulting in a financial impact of $7.3 million. The study underscores the significance of precise blasting techniques and effective spillage control in enhancing mining recovery rates.

Jan 21, 2025

By J. Parke Channing

ALTHOUGH the original thought of investigating waste in industry came from a mining engineer, Herbert Hoover, and although the chairman of that committee was a mining engineer (although the real work was done by the vice-chairman, L. W. Wallace), it is an interesting commentary that when the report first saw light, at St. Louis, on the first of June, 1921, some people most violently went up in the air when it was submitted by the representatives of the mining engineers. At the time they resented most markedly the report of the committee that 50 per cent. of the waste in industry, or as Mr. Ingalls in his paper has properly said, inefficiency in industry, was to be laid upon management. The reason for that seems to have been that, as a whole, the mining industry is pretty well organized and is superior to a large number of manufacturing industries including those studied by the Report. However, this very meeting shows that even the min-ing engineers have finally realized that there is waste or inefficiency in mining and that a large proportion of it can, with propriety, be assessed against management.

Jan 3, 1922

This Bureau of Hines report on underground mine communications addresses methods and equipment to meet the communication requirements of working sections and places of coal and metal-nonmetal mines. A review of the status of trapped miner detection is also presented.

Jan 1, 1977

By E. W. Garner

THE greatest problem confronting business managers in modern times is not production, but distribution. It would be easy to expand productive output, but it is difficult to find markets for all that is produced. The fundamental source of economic difficulty, in the view of many observers, is a lack of proper balance between productive capacity and consumptive capacity. The studies conducted by the Brookings Institution on the general subject, "The Distribution of Income in Relation to Economic Progress", have led to conclusions of far-reaching significance, which may be summarized briefly as follows: (1) We have never lived beyond our economic means or capacity. (2) We have not been suffering from general overproduction. (3) We have not as yet reached a stage in our economic evolution at which it is possible to provide adequate standards of living for everybody. ( 4) It would require less than a 25 per cent increase in purchasing power among the masses to absorb our full productive capacity. (5) Production-curtailment programmes-whatever their merit in meeting temporary maladjustments-can only lead to national impoverishment. (6) Our inability to find markets adequate to absorb the full output of our productive establishments is explained by the unequal distribution of income and consequent restricted flow of purchasing power through consumptive channels. (7) The slow rate of growth of consumptive demand serves to retard the rate at which new capital is constructed, and hence the rate of economic progress. (8) The primary need is a rapidly expanding total income, and a broader diffusion of this income among the masses of the people. (9) A broader diffusion of income can best be achieved by reducing prices as rapidly as increasing efficiency will permit. That is to say, the benefits of technological progress, mass production, and low unit costs must be promptly passed on to consumers in the form of lower prices-giving more for each dollar.

Jan 1, 1936

By Benjamin Smith Lyman

PAGE I. ANCIENT HISTORY,........... 57 Accepted Fables ; Babylonian Mapping ; First Surveying. II. COMPASS,.............59 Chinese Invention; Marco Polo; First European Compasses ; Early Knowledge of Variation ; Plotting with the Compass ; Hanging-Com pass ; Supposed Gravitational Error ; Merit of the Compass. 111. Telescope,............63 Origin (Roger Bacon, Porta, Digges, Lippershey, Galileo) ; Improvements (Micrometer and Cross-Hairs, Rittenhouse's First Telescope, Platinum Cross-Wires, Telescopic Sights, Reflecting Telescope, Achromatic Lens, Kellner Lens in Erecting Telescope, Inverting Telescope). IV. Theodolite,.............81 Origin ; Derivation of the Name. V. TranBit,.............86 First Surveying Transit; Edmund Draper. VI. Instrument-Parts,..........89 Ramsdenl a Dividing Engine ; Fineness of Graduation ; Conical Gradua tions ; Full Vertical Circle ; Leveling-Screws ; Shifting Tripod-Heads ; Hoffman-Harden Tripod-Head ; Heller & Brightly's Improvements. VII. OTHER INSTRUMENTS AND APPLIANCES,......100 Sunflower; Plummet-Lamp; Chains and Tapes. VIII. SCOTT'S TACHYMETER,.........104 IX. Nomenclature and Classification,.......105 Names; Grouping. Surveyors are much indebted to Mr. Scott for so vigorously attacking the subject of the origin and history of mine-surveging instruments, the compass, the telescope, the transit and other apparatus. He is not afraid of the dark, nor yet foolishly bashful in broad daylight. He does not recoil from the obscurities of the earliest times and the most difficult historical points; and, with commendable public spirit, he makes his own invention known to his fellow-workers, and challenges their criticism. He has, moreover, elicited the praiseworthy emula-

Jan 1, 1902

By O Joneydi, J Viljoen, R Funnell

Computational Fluid Dynamics (CFD) modelling is a useful tool that can assist engineers in designing effective ventilation systems for the control of airborne dust generated during mining operations. Thistechnology can save time, effort and the costs associated with re-work or the traditional on-site experimental field trials by running desktop 3D simulations of the various proposed scenarios using state-of-the-art CFD analysis tools. Before implementing a dust management system, an understanding of the behaviour of airborne dust particles in the face zone can be achieved, which can improve the confidence in the secondary ventilation and dust management design. Usingadvanced numerical models, suitable dust extraction strategies can be foreseen, and multiple scenarios can be simulated and investigated quickly. As a case study, dry drilling operations in Kimberlite orebodies produce large quantities of fine dust which poses health and safety risks. An effective dust management system is required to achieve acceptable face conditions. A possible practical solution is a ducted exhaust ventilation system with a force fan in the face zone. This paper demonstrates how CFD analysis can be used as a tool to assist the design engineer with validating and optimising the proposed ventilation design by tracking the trajectories of different size dust particles, to determine the best equipment layout and appropriate flow rates which minimises airborne dust.

Oct 12, 2022

By B. W. Hester

Report of discussion at January, 1971, general meeting (Chairman: M. J. Cahalan, President) of the paper published in Transactions/Section B (Applied Earth Science), vol. 79, May, 1970, pp. B60-B67, and contributed remarks. Comments were made by Taylor J.T.M., James C.H., Lethbridge R.F. and Heath K.C.G.

Dec 1, 1971

By N. A. C. Smith, A. C. Fieldner, R. R. Sayers

Gases and vapors given off by petroleum and its products have long been recognized as somewhat injurious, when inhaled in high enough concentrations. The petroleum industry has recognized these effects and has tried to minimize the possibility of employees encountering dangerous concentrations of the vapors. Petroleum gases and vapors have not, however, been considered as actively poisonous, in the sense that hydrocyanic (prussic) acid and phosgene are poisonous; men have been exposed to them repeatedly, and for long periods, without any marked ill effects. Light Mexican crude oil when first introduced into the United States for refining was handled in much the same way as was customary with other apparently similar crudes; but experience soon showed that some toxic substance escaped from the crude during production and transportation and in most of the refinery operations. After a preliminary investigation several of the larger companies decided that the gases from the petroleum were the source of trouble, and therefore took precautions, wherever possible, to protect the men from exposure to these gases. With the increasing use of Mexican crude, this problem has become important. The present report covers the work done on the subject by the Bureau of Mines and the Public Health Service under a cooperative agreement with the American Petroleum Institute.

Jan 1, 1925