Search Documents

By F. R. Joubin

MR. CHAIRMAN, Members of the C.I.M., and Friends -particularly friends, because I am not entirely a stranger in your city. I was last here some five years ago and it has given me a great deal of pleasure this evening to be able to say "Hello" again to those I had met at that time, when Bourlamaque and V al d'Or were very busy centres of intensive and successful gold exploration. My remarks this evening have to .do with Canada's Place in the Atomic Age. They will be of a general nature but I hope to tell you ?enough to whet your appetite so that you may be provoked into per-.suing the subject further. Now, atomic developments have become quite commonplace. Words like radioactivity, reactors, nuclear fission, and so on are known to everyone, even the youngsters. I re-member two or three years ago one of my office boys came to me and said "Mr. Joubin, I would like a raise." I gave the request a few seconds of serious thought and finally said "Alright, Jimmy, we'll give you a raise." However, he made no effort to leave, so after a -couple of seconds more I said, "Is there something else ?" and he said "Yes, Mr. Joubin, could you make that raise 'radioactive' to the first .of the year ?"

Jan 1, 1958

By James B. Fletcher

The Miami mine is located near the town of Miami, Gila County, Arizona. The Miami mine started mining in 1910 and finished in July, 1959. The orebody was divided and mined as follows: Tons High Grade 24,400,000 - Top slicing, sub-level caving, etc. Low Grade 105,100,000 - Block caving Mixed ore 9,800,000 - " Low Grade #2 13,100,000 - " Total Mining 152,400,000 GEOLOGY Ore minerals are largely in pre-Cambrian Pinal schist intruded by tertiary Schultz granite porphyry and covered to some extent by Quarternary Gila conglomerate. The structures are highly faulted and shattered. The Miami fault on the east cuts off the ore and the Pinto fault on the southwest caused re-oxidation of enriched sulphides producing mixed ore. MINERALOGY The chief mineral is chalcocite, with chalcopyrite, bornite, covellite, malachite, azurite, chrysocola, cuprite, native copper, and molybdenite as minor minerals. The ore minerals occur in seams, veinlets and disseminated particles. In block caving there is always some dilution, and drawing of ore stops when the grade drops past an economical point. This results in a small amount of copper left in the stopes below the capping. There is some copper in the capping, probably below 0.03% or less than 0.6 lbs. per ton. Over the low grade #2 orebody and portions of the high grade there was an oxide capping which was not mined. The crushed pilars are another source of copper. The leaching at Miami is an attempt to recover this last remaining copper of a worked-out mine. The enrichment at the Miami mine had gone more nearly to completion than most ore bodies in the southwest. There is practically no pyrite in the capping and very little in the ore.

Jan 1, 1971

By Paul Riches

LR Process Expert is a cost-efficient process automation system for all types of long rolling mills, including, rod, bar, section, rail, reversing mills, and flat blocks. The system performs a wide range of tasks for optimized operation – from suggesting pass schedules to calculating and downloading optimized mill settings according to the availability of rolls. LR Process Expert also monitors and collects data from the raw material stage through to the finished product. It delivers valuable mill reports to the operator staff and management so they can easily assess a plant’s performance and optimize production. Defined Key Performance Indicators (KPIs) help to assess a plant’s performance; this system is not limited to one plant but can enable plant-toplant performance at corporate level.

Aug 16, 2017

By S. S. Gross

A program was conducted to determine whether sufficient quantities of the flame retardant, ammonium phosphate, could be incorporated in a water-based foam solution to prevent or delay reignition (burnback) without. significant degradation of foam properties. Up to 20% of mono and diammonium phosphate was added .to d high expansion foam solution. This mixture was applied as a high expansion foam to burning wood and coal samples. The effect of this mixture on burnback was laboratory tested by placing the wood or coal sample in front of a radiant panel. It was found that diammonium phosphate levels of 20% by weight prevented reignition without degrading foam properties. A field test was then conducted using a 20%, diammonium phosphate mixture and a control with no phosphate on a wood crib fire. The experimental foam did extinguish the crib fire faster than the control as evidenced by the smoke from the crib. However neither crib reignited.

Jan 1, 1982

By William W. Aljoe

This report summarizes the Bureau of Mines noise-control research program from 1972 to 1982. Each segment of the mining industry--under- ground coal, underground hardrock, surface mining, and processing plants--has different noise-control problems because of vast differences in working procedures, equipment, and workplace design. The Bureau has identified the most serious noise problems in each segment and has developed strategies for attacking these problems. This publication points out the need for noise control in the mining industry, discusses Federal regulations governing worker exposure to noise, and describes the Bureau's overall approach to mining noise- control research. It traces the history of noise overexposure in each segment of the mining industry and discusses the major noise sources. It provides detailed information on noise-control research efforts in the Bureau's major areas of emphasis, including the results of these efforts. Finally, the report discusses the Bureau's future role in research on mining noise control, emphasizing the need to expend more effort on long term in-house investigations into the noise problems that have been identified in past programs as the most serious ones.

Jan 1, 1985

"This contribution is concerned with adaptive processing decisions, where the process parameters are optimally adapted to the varying properties of the material input stream. Our starting point is the geometallurgical paradigm that the varying properties of the input stream are considered known e.g. from a geometallurgical model of the mined ore body, and optimal processing parameters are computed from them, by finding the parameter seaming optimal in a computer simulation.This approach however has to work with a lot of uncertainties: The prediction of the geometallurgical ore parameters can only be done with some geostatistical uncertainty. The parameters themselves are only proxies for true ore properties. Model prediction can differ relevantly from actual process results, due to model simplifications. Due to these uncertainties the computed processing choices can turn out to be inferior to simple non-adaptive processing. In this contribution we focus on the uncertainty of the ore properties and analyse this effect systematically, by modelling this uncertainty effect mathematically and in computer simulations. The most important findings are:(a) Processing choices not taking into account the uncertainty sometimes even perform worse than simple non-adaptive processing, for the sole reason of ignoring the uncertainty effect.(b) Ore properties, not adequately reflected in the ore description, might require different approaches, in which the observed processing behaviour feeds back into process control.(c) Bayesian decision theory allows computing optimal processing choices combining the information from the mine (geostatistical predictions) and from the process feedback. These choices give much more robust choices and do not suffer from the drawbacks described for the simple approach we started from.These new approaches can substantially improve the performance of adaptive processing in existing plants."

Jan 1, 2016

By Scott Turner

I have been asked to speak briefly about recent progress in the mining industry of the United States, and to touch on the general advancement of en- gineering science as applied to mining. By recent, I shall mean within the past 20 or 30 years. Such a period includes a great many of the changes which are of particular interest to the present generation of engineers, and the undergraduates of today will hardly turn back farther than the beginning of the present century in their study of develop- ment of methods and processes. Also, my own professional life spans this period, and I have seen or have been aware of most of these developments as they were taking place. In my review of developments, for the sake of simplicity and clarity, I shall deal separately with improvements in metal mining, coal mining, mechanical and electrical machinery for mines, metallurgy, petroleum engineering, and safety practices. Under each of these headings I have set down what appear to me to be the outstanding changes brought about during the past 2 or 3 decades. Other points will occur to other engineers; I do not represent that the following re- view is complete; it is only intended to be suggestive. In general, improvements in mining and metallurgical practices have come gradually, the charges being effected little by little, simultaneously in widely scattered places, and through the experience and inventive genius of many men. These changes have has small beginnings, and are generally the cumulative result of many steady and unsensational progressions, which still continue. What we today might be inclined to consider the culmination of a series of betterments in mining is, of course, but an instantaneous phase of developments which will continue in the future at even a more rapid pace than they have in the past. We are looking at but a flesh of a moving picture, with an endless reel to come after we finally leave the theatre. Behind all the changes in the mineral industry, the driving force has been the increasing demand of an expanding population for more metals and minerals with which to advance civilization. More people, with an increasing per capita consumption, together with the exhaustion of the richer but smaller, and more

Oct 1, 1930

By Bruno Vingiani, Alessandro Bertero

"The use of Artificial Ground Freezing (AGF) for temporary soil strengthening and seepage control is an effective alternative to grouting when dealing with soils whose degree of finesses would imply the use of highly expensive chemical grouts. However, compared to grouting, the application of this improvement technique usually needs a more accurate preliminary soil investigation campaign and a design assisted by specific calculation software. Besides a general description of the main features of this technique, the paper will describe a recent application of AGF carried out in Rome to underpass an existing metro station.INTRODUCTIONNatural ground freezing occurs seasonally or permanently (permafrost) in some areas of the globe close to the poles and can negatively affect the engineering performance of underground structures. On the other hand, Artificial Ground Freezing (AGF) is man-made controllable freezing process that can be used in foundation engineering to temporarily strengthen the ground and create a barrier to the passage of groundwater. During the process, the heat is extracted from the soil in a cylindrical shape around a number of freezing pipes installed into the ground. This action produces columns of frozen soil, which expand gradually till they merge and create continuous frozen wall. The thickness of this barrier can be regulated according to the specific project requirements. Nowadays, AGF technique is applied to a wide range of foundation engineering problems where soil stability and groundwater flows are an issue (Pimentel et al. 2011, Haß and Schäfers, 2013). Typical applications include the temporary stabilization and waterproof of the ground around the excavation profile of mined tunnels until the construction of the final lining (Figure 1).The case history described in this paper deals with a recent application of AGF carried out during the construction of metro Line “C” in Rome. Specifically, this technique has been applied to allow the construction of two single-track mined tunnels running underneath an existing metro station belonging to Line “A”. In that case, the AGF has been evaluated by the Designers as the only possible solution for improving the mechanical and hydraulic characteristics"

Jan 1, 1900

By M. Javier

"Mining is the main activity that supports civilization. Actual mining presents contradictory concept to the health of the planet. Its business model is linear, fragmented and characterized by inefficiencies in the utilization of water, energy and mineral resources which generate waste and pollution. Before mining begins, it is critical to determine the vulnerability of the ecosystem and after mining, it is critical to determine the depletion of nature. Attending to these vital matters will require quantifying and measuring them. The purpose of this study is to provide and establish the metric to assess the performance and manage a sustainable future for our existence and that of our planet. This index is defined to measure and control Nature Friendly Sustainability (NFS) based on understanding nature. This index will determine the condition of nature constructed on the measurement of physical, chemical and biological equilibrium. Proposing a new mindset for mining design to satisfy nature’s needs would be to offer the same opportunities to future generations. Hence, sustainability is synonymous with equilibrium under a limited ecosystem. Nature is interconnected. Finally, this index of NFS is readable, standardized and relevant to keep nature’s needs in equilibrium. Establishing and NFS index is the next metric for humanity. INTRODUCTION There are a multitude of definitions of what sustainability is. Most of them are defined in terms of the corporate entity from which they emanate. The classical definition of management states that, “if we do not measure it, we cannot manage it.” Management of ecosystems is the definition of sustainability. Indicators of quantity and quality of sustainability are vital in order to create a metric for sustainability. These indicators will measure the depletion and degradation of nature as they occur through human intervention. The first step is to create a metric of sustainability to simplify its definition. The definition of sustainability is based on whether or not you consider nature to be finite or infinite, which is described in Nature Friendly Sustainability (NFS) [1]. The definition of NFS applies to any anthropogenic activity with an understanding of the equivalent activity in nature. That is to say, human activity with nature requires balance and equilibrium in order to be sustainable. The importance of this equilibrium is quantified in a set of metrics in order to establish measurement and acknowledge indicators for our dependence on nature. Sustainability is synonymous with equilibrium in any ecosystem that is limited and fragile. In the graph is the explanation of sustainability definition. See Graph 1"

Jan 1, 2017

Operator efficiency and control capability along with cost effectiveness have been the quest of mining, industrial, and mobile hydraulic engineers for years. The majority of the functions in present day fluid power systems are controlled by on/off control valves. They are inexpensive and provide easy installation and operation, but they lack the quality of fine control of load flow or what is sometimes known as "feathering the load". An alternate approach to obtaining this capability is the use of electro-hydraulic servo-valves, but their implementation into a system is complex, and they are expensive. As a result, electrohydraulic systems are still used primarily in the aerospace industry. Of late, a compromise seems to have evolved between the on/ off control systems and the servo-technology is the so-called proportional flow control valves. A proportional flow control valve meters fluid to the load in proportion to the input command from the operator. In principle, it is similar to a conventional flow control valve and is tailored to meet the control requirements from the load point of view. The hydraulic system using this valve usually works in an open-loop mode with the operator closing the loop. Incorporating load-sensing mechanisms and adoption of electrical/electronic signalling into the valve make it the "ideal valve" which designers have been looking for from a techno-economic point of view.

Jan 1, 1983

By F. Andrieux

"Extruded aluminum profiles are increasingly used for lightweight vehicle construction. Since fracture strains of aluminum profiles are relatively low, damage modeling is crucial for reliable crash simulation. For aluminum profiles, not only the stress state but also the orientation influenced both the deformation and damage behavior. For the material characterization smooth tensile tests were performed in six orientations, both stress-strain curves and r-values were registered. Moreover notched tensile and shear-tension tests were performed in three directions. Finally punch specimens were tested to investigate biaxial loading. Digital image correlation (DIC) analyses were performed to determine local strain values such as critical values at failure. Numerical investigations were conducted with the strain based damage model GISSMO, which is well suited and widely applied for crash simulation. For a strain based failure model the choice of the deformation model is crucial. Deformation models with increasing complexity were investigated to find the best compromise over all experiments. It was found that there is still a great requirement on development of a material model which describes the orientation dependence of the hardening behavior over all stress states in order to be able to use a strain based failure model reliably.INTRODUCTION Weight reduction is an important step for less energy consumption and as a consequence aluminium is increasingly used in automotive parts. An important field of application is the well-established aluminium extrusion which allows the realisation of quite complex shapes of profiles required for an innovative lightweight design with integrated functions. Typical applications are chassis parts, bumpers, crash elements, air bags, etc. Especially the Al–Mg–Si medium strength alloys of the 6000 series can be easily extruded to form complex profiles and prevail for extrusion. Since fracture strains of aluminum profiles are relatively low, damage modeling is crucial for reliable crash simulation. For aluminum profiles not only the influence of the stress state but also the orientation with respect to the extrusion direction have an influence on both the deformation and damage behavior and need to be characterized. The effect of orientation on deformation behavior has been intensively investigated in the last decades and material models haves been proposed (e.g. Barlat & Lian, 1989; Barlat, Lege, & Brem, 1991; Barlat et al., 2003) to describe accurately anisotropic behavior. However it can be noticed that the parameters of anisotropic material models often rely on the yield stress in different directions, which means that the effect of strain hardening is not automatically accounted for. The accuracy of the models at large deformation is not guaranteed and has to be verified. In contrast to deformation models both the characterisation and the modeling of anisotropic damage behavior are not systematically studied. Isotropic failure models based on a critical strain as function of stress triaxiality (ratio of the hydrostatic stress to von Mises equivalent stress) are widely used for crash application (e.g., Bai & Wierzbicki, 2010; Sun, Andrieux & Feucht, 2009; Sun et al., 2013). The mechanisms of failure are manifold and not fully understood; to develop an anisotropic failure model it is mandatory to also have experimental data in different orientations for loading scenarios other than uniaxial tension, e. g. shear, biaxial tension, which implies an extensive experiment plan. This makes the development of failure models more challenging than deformation models for which it is possible to develop a reasonable anisotropic model using the framework of yield function and calibrate the material parameters based on results of tensile tests in different directions. Moreover the development of deformation and failure models are intricate as the variables governing the damage evolution are predicted by the def"

Jan 1, 2018

By Ernest R. Lilley

THOSE acquainted with the fundamental differences between the, educational .systems of Great Britain and. the United States would hardly expect .the training of men for the petroleum industry to proceed along the same lines- in the two countries. The youth entering an English university is, except in the case of-the student from some of the British colonies or from foreign countries, almost invariably a product of the English "public school." This is in no sense comparable .with the American public school. It is a private institution, frequently of considerable age and heavily endowed. In many aspects it seems to be comparable with the American preparatory school. Yet to some extent its activities remind one of the first years of the undergraduate: course in the American college. Certainly it takes to-itself many of the social, functions of the American college.

Jan 1, 1931

By R. Blazej

Machinery Systems Division (MSD) in the Institute of Mining Engineering at Wroclaw University of Technology specializes in belt conveying systems analyzing, calculating and design. Within the division operates the certified Laboratory of Belt Transportation (LTT) and Laboratory of Rollers. Since few years, a group of several people have begun work on developing a comprehensive system for the automatic evaluation of condition of conveyor belts working in the mines. Group uses both magnetic devices developed by specialized companies servicing belts and its own machine vision system developed for assessment of belts covers and edges during belt movement (up to 7 m / s) on the specially designed for this purpose the test conveyor. Recently they have got the research grant funded by the National Centre for Research and Development (NCBiR) for development of the system for automatic diagnosing of conveyor belts? condition and aiding of rational belt management. On the basis of previously created diagnostic tool called ABCDE (Automatic Belt Condition Diagnostic Equipment) the five modules: vision-A magnetic-B, preventive-C, forecasting?D, and determining safety factor-E will be developed. They will automatically interpret data about conveyor belts? condition to indicate the extent and timing of repairs, to prevent failures and to select the optimum moments for their replacements. The system will use results of ongoing research & development and planned research concerning modeling of belt wear using evolutionary genetic algorithms. The reached stage of research can not yet allow to start the implementation work by potential users. It is therefore necessary to pursuit research in real scale, the development of new modules (C-E) and intensive testing of the system in working condition with system calibration to optimize the economic effects.

Aug 1, 2013

By Fernando Velazquez Guzman

Titanium is an alloying element used to refine grain size in steel and improve its physical and mechanical properties. In some stainless steels it is used to increase the resistance to corrosion by the precipitation of titanium carbides or carbonitrides. Its alloying performance is highly variable and depends largely on the stage of the secondary metallurgy process when it is added. Furthermore, the addition method (wire injection or direct addition) has a remarkable influence in secondary refining. This paper describes the tests performed in vacuum degasser (VD), with a highly compacted and encapsulated Ferrotitanium wire (FeTi HC). The yield of titanium in steel increased from 52% to 89%. Moreover, the consumption of the highly compacted Ferrotitanium was optimized.

Oct 30, 2017

By C. A. Cole

This work consists of research in cable fault location and the construction of four field-test units based on the research. Swept-frequency sounding of mine cables with RF signals has been the technique most thoroughly investigated. The swept-frequency technique is supplemented with a form of moving target indication (MTI) to provide a method for locating the position of a technician along a cable and relative to a suspected fault. Separate, more limited investigations involved high-voltage time domain reflectometry and acoustical probing of mine cables. Particular areas of research included microprocessor-based control of the swept-frequency system, a microprocessor-based fast Fourier trans-form for spectral analysis, RF synthesizers, transmit-receive switches, RF receivers, cable dispersion-compensation techniques, low-voltage multielement display systems, and techniques for injecting or recovering RF energy through cable walls in support of clamp-on fault locators.

Jan 1, 1982

By F. W. Gray

Ideal utilization of the heat energy in coal should theoretically be secured by supplying each atom of combustible material present with the exact quantity of oxygen necessary for complete combination. An intimate and equal admixture of the fuel particles with air is therefore to be sought. Coal, or the combustible substances of which coal is composed, may be used in solid or liquid or gaseous form. The use of coal in small particles intimately mixed with air is, in effect, a specification of coal in pulverized or dust form. There has been much important development of this manner of using coal, which may be instanced as the outstanding advance in the use of coal as a solid. The completeness and efficiency of combustion in a properly designed dust-fired furnace permits the use of locally available coals of inferior quality, and enables them to be used commercially instead of imported coals of better quality. That is to say, some grades of coal of low calorific value, that are not economically useable in lump form on grates, are useable in pulverised form, because of the more complete combustion thereby obtained, and the consequent more efficient results. In the case of coals that are unsuitable for steam-raising in grate-fired furnaces, because of clinker troubles, (arising usually from a combination of high sulphur content and low-temperature fusibility of the ash content) use in pulverised form has obvious advantages, and in addition gives the benefit of any heat units that are contributed by free sulphur in the coal.

Jan 1, 1924

By W. J. PRIESTLEY

WHEN during the war the Navy Department decided to build an armor-plate and gun-forging plant of its own at South Charleston, W. Va., one of the most important units of the equipment proposed was a 14,000 gross ton forging-press to be used for forging, bending, and rectifying battleship armor-plate and making hol¬low forgings for large caliber guns. A press suitable for doing this kind of work was put into operation in the fall of 1921 and was operated successfully on armor-plate and large forgings until the closing down of the ordnance plant following the Limitation of Armament Conference held in Washington, February, 1922. PURPOSE OF THE PRESS There are three methods by which armor-plate can be made, namely, hammering, forging, and rolling the ingot. Each method produces a different result in the mechanical working of the steel. The hammer was eliminated as impractical from an operating standpoint. The first armor-plate made in this country was worked under a hammer at the Bethlehem Steel Co., between the years 1891 and 1893, but was superseded by forging when the large press was completed in 1893. Harry T. Morris of the Bethlehem Steel Co. informs me that the 1.25-ton steam hammer began operations in 1891 and was in operation for about two years. The Carnegie Steel Co. and the Midvale Steel and Ordnance Steel Co. also forged armor-plate. Certain European manufacturers rolled the plates from large slab ingots, after removing the sink-head and giving the body of the ingot a light pass under a hydraulic press. While rolling accomplished more mechanical work on the surface of an armor plate, forging, on the other hand, resulted in a greater amount of work in the interior of the plate. Either type of equipment involved an enormous expendi¬ture, so it was deemed advisable to adopt the method which would make it possible to use the equipment for more than one purpose. Since g large rolling-mill could be used only for the single operation of rolling armor-plate, a press was decided on, for the reason that it might be designed so as to forge armor, as well as bend and rectify it, and also be used in the forging of ingots for large caliber guns, both in the form of hollow forgings and also solid shafts.

Jan 1, 1926

By K. Swedburg, M. Samuels

"The New Afton concentrator was commissioned in June 2012, reaching the design milling rate in September 2012. By late 2013, through a campaign of optimization and de-bottlenecking, it was recognized that the installed plant was capable of greatly exceeding the design throughput of 11,700 tpd. Because the value of the metal contained (by increasing the plant feed rate) exceeded the offsetting losses of copper and gold recovery (as the operation moved to a coarser grind), the concentrator feed rate was strategically increased with support of New Gold, while the operations team was given a mandate to evaluate, and then implement, flow sheet options that could re-establish the original design criterion grind target and achieve the corresponding improved recovery. Broadly, the two options implemented were the addition of a tertiary grinding stage consisting of Metso Vertimill® prior to rougher flotation (in order to address the grinding required at increasing throughput by increasing the power), and the addition of three Woodgrove Staged Flotation Reactors (SFR) added to the cleaner circuit after regrind of the rougher concentrate (to address the increased mineral loading to the cleaner circuit). Through test work, it was anticipated that the SFRs would be capable of achieving final concentrate grade in a single pass without the integration of recirculating loads, a strategy sometimes referred to pre-cleaning. This paper describes the expectations generated for the Woodgrove SFR unit operation through pilot plant testing on site, and compares those results with the performance of the expanded circuit that exceeded the original design criterion of P80 160 µm, which was commissioned in the second quarter of 2015.INTRODUCTIONThe New Afton concentrator, located near Kamloops, BC Canada, commenced operation in June 2012. The mill achieved the design throughput of 11,000 tonnes per day average during the month of September 2012 and, following various operational optimization efforts (O’Hara et al, 2015), achieved the design p80 grind size of 160 µm at the design milling rate in July 2013.During August 2013, trials were carried out to determine the throughput rate limits of the mill circuits and to evaluate mill metallurgical performance at higher rates. Milling rates up to 15,500 dmt per 24 hours were achieved during this trial, demonstrating potential capability for sustained milling rates exceeding the nominal design capacity. As was expected, the higher milling rates resulted in a coarsening of the grinding circuit product size, and resulted in marginally lower recoveries in the rougher flotation circuit. Despite the lower recoveries, the higher milling rates resulted in higher metal production and the financial analysis favored running at rates of at least 13,000 tonnes per operating day, with the higher cash flow in the near term offsetting the value of metal production loss at the end of the mine life (due to the short term increase in the rate of reserve depletion). Milling rates were sustained above 13,000 tonnes per day through the second half of 2013, and increased above 14,000 tonnes per day by mid-2014 (Figure 1)."

Jan 1, 2016

The Bureau of Mines found sulfur hexafluoride (SF6), released from a lecture bottle, to be an ideal gaseous tracer for studying mine ventilation systems. Air samples were collected in glass syringes and analyzed by electron-capture gas chromatography. In these studies, the lower limit of detection was about I part per billion by volume (ppb) of SF6 per part of air. Experiments conducted in a Pennsylvania limestone mine showed this technique useful in evaluating the effectiveness of auxiliary fans, measuring low flow velocities, probing the air circulating near a working face region where ventilation appeared to be poor, and estimating volumetric flow rates in airways of large cross-sectional area and having low flow velocities. This technique was also used in a western vein-type metal mine to measure the amount of return air being recirculated into the intake air due to leakage through old stoped areas.

Jan 1, 1974

By W. A. Haley

Wheel loaders became important bulk materials handling tools in the early fifties. As they grew in stature, productivity, reliability, and acceptance, the demand for larger, more rugged machines evolved. In the early sixties, the introduction of a 6-yard model by a major equipment manufacturer led quickly to widespread experimenting and rapid worldwide acceptance in loading blasted rock in stone quarries and smaller metal mines. As the wheel loaders grew in popularity for shot rock loading, larger models, 12- to 15-yard size were developed and saw widespread use by 1970. In the past 20 years, at most quarries and small to medium size mines, most cable operated power shovels have been replaced by large wheel loaders and more recently, hydraulic excavators as the primary loading tool. Wheel loaders larger than the 15-yard class are not used widely. Until about 1970, very few overburden haulage trucks were used in domestic coal mines. About that time, many states started enforcing stringent mine relcamation regulations and in 1977, even more stringent federal legislation was passed. These controls brought about drastic changes in coal surface mining methods in the mountainous areas of Appalachia, in smaller midwestern mines and in the large mines of the western states. Basically, simple material casting methods were replaced at most eastern mines by "haul-back" and "mountain top mining" methods using controlled placement of overburden as it is removed from the coal. These methods dictated much more extensive use of loaders/ shovels and trucks to the point that most coal mining in those areas is now by loader/shovel trucks methods. And those areas have become the home of the country's largest population of large wheel loaders and trucks in the 35- to 85-ton size class with a trend to even larger trucks and shovels. To maintain equal production or provide for growth, the new methods have caused a sharp increase in machine intensity to the extent that at some mines, up to three times as many machines were required to mine a million tons of coal in the late seventies as compared to the machine needs in the sixties. Mining costs and coal prices also took a big jump in the mid-seventies, paralleling the drastic price increases in oil and other forms of energy.

Jan 1, 1984