Search Documents

By P Hulteberg

In this article, an integrated catalytic reactor design approach to produce PEMFC-quality hydrogen is evaluated. The design is based on a high level of heat exchanging perfonned internally, highly active noble metal catalysts and a woven wire mesh catalyst support system. It consists of an integrated steam refonner and a catalytic burner section, a water gas shift section and a preferential carbon monoxide oxidation section. The reactor design is described and experiments perfonned to evaluate the two reactors built are reported. The two reactors have a maximum output of 3 Nm and 10 Nm3 hydrogen/h respectively. In the larger unit, a total of six fuels, three gaseous (methane, natural gas and liquid propane gas) and three liquid (naphtha, ethanol and methanol), were evaluated. The larger unit was also used to investigate how variations of parameters such as steam-to-carbon ratio in the steam reforming part of the system and the relation between oxygen and carbon monoxide in the preferential carbon monoxide oxidation affect the reactor perfonnance. The smaller unit was used, after implementing automatic control, to run a system life time test for 480 h. The refonner system perfonned according to specifications on almost every aspect.

Jan 1, 2005

By K M. P Singh, K M. K Sinha, G S. Jha, T Gouricharan, K K. Sharma

The majority of the powerplants in India are fed with non-coking coals, with the coals dispatched from their respective mines via wagons loaded by a rapid loading system or pay loader. The usual top size of coal is 200 mm and sampling is carried out manually from wagons. The manual method of wagon top sampling of large size raw coal is not only difficult, but also violates some of the fundamental principles of sampling. As per sampling requirements, samples are to be drawn from the full depth of the wagons, which is impossible to be done manually. Since the ash distribution in the different size fractions is not homogeneous, the results from the samples, which do not reflect the true size distribution of the lot, are likely to be biased. More importantly, sample collection by shovel from the top is a function of human discretion and not governed by the equiprobability rule. In another case, the sample has been collected by a cross belt-type auto mechanical sampler for 200 mm size coal at one of the super thermal power stations. Test analysis shows that coal collected using a cross belt-type mechanical sampler also has significant deviations from stopped belt coal samples of 200 mm size due to size segregation. Studies carried out on wagon top sampling through specially designed experiments reveal some interesting features. The presence of bias in wagon top sampling is apparent when compared with the ‘stopped belt’ sample. In this paper, a comparative study between manual wagon top sampling/auto mechanical sampling with respect to stopped belt sampling has been conducted for coal of size 200 mm. In addition, precision studies have been performed for wagon top sampling/mechanical sampling for Indian thermal powerplants.CITATION:Sinha, K M K, Sharma, K K, Jha, G S, Singh, K M P and Gouricharan, T, 2014. A comparative study of manual wagon top sampling and auto mechanical sampling of 200 mm size coal with respect to stopped belt sampling of thermal coal at Indian super thermal powerplants, in Proceedings Sampling 2014 , pp 43–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By A. U. Miller

The added hazards to mining incident to oil and gas wells penetrating the coal measures in proximity to mine workings , have long been recognized in those fields where the extraction of oil , gas , and coal , has been in progress for a number of years . The history of these fields is replete with stories of serious mine fires , explosions , and miraculous escapes from both fires and explosions due to either oil or gas finding its way into the mine workings through the strata , or by mining into an unknown or uncharted and abandoned oil or gas well that had not been properly plugged . The Director of the Bureau of Mines , in response to numerous requests from coal operators and oil and gas operators , called a meeting in 1913 to discuss necessary precationary measures to take when drilling oil or gas wells through workable coal beds and to try, if possible . to formulate a set of regulations that might serve as a guide to those persons preparing regulations covering the drilling of oil and gas wells in the various coal producing States . This meeting was attended by representatives of the coal , oil , and gas industries , State geologists , State mine inspectors , and representatives of the Bureau of Mines . A committee was appointed to prepare a set of regulations , which was later published as U.S.Bureau of Mines Technical Paper 53 ; the discussions and results of the meeting werepublished as U. S. Bureau of Mines Bulletin 65 . Later , the American Institute of Mining and Metallurgical Engineers appointed a committee to draft a model law for the use of the legislature of any State concerned . This committee made its report on April 27 , 1928 . Several of the coal mining States now have more or less comprehensive regulations governing the drilling of oil or gas wells through workable coal beds , others have regulations that are inadequate , while some have no regulations . The State of West Virginia recently enacted a law containing reg lations which are the result of a comprehensive and careful study of the problem .

Nov 1, 1929

By R Nicholson, N D. Cox, N W. A Lambert

"This paper reports on the long-term operation of a particle density meter (PDM) at the Bloomfield coal handling and preparation plant (CHPP). This unit has been operating continuously for over three years, providing real-time data to the operators to allow the monitoring of flotation circuit performance. PDM outputs include slurry density, solids concentration on both mass and volumetric basis, and particle density. Knowing the average particle density of a stream allows for the optimisation of the process in real-time.The calibration of the solids concentration measurement device proved very difficult as the factory calibration techniques and existing laboratory analysis did not give accurate or reliable results. The solids concentration device had to be re-engineered and a new calibration method developed that gave accurate and repeatable results. Independent verification of samples taken from the PDM was undertaken as part of the trial process.The operational reliability of the PDM was a major point of investigation. The initial installation of the unit revealed issues with large, misplaced material of up to 20 mm periodically entering the unit, leading to feed blockages. The presence of these misplaced, oversized particles in the flotation circuit was resolved by installing innovative automatic back flush systems on the PDM.From a plant perspective the PDM has been an invaluable instrument that has enabled irregularities in the flotation circuit performance to be identified, which sampling had not and could not readily identify. This was achieved by close monitoring of real-time tailings composition on a minute by minute basis over short and extended periods. Variations in the tailings stream with respect to particle density and solids concentration were traced back to other issues in the plant. In addition, the PDM has allowed cell optimisation with respect to reagent dose rate to be improved. The PDM with real-time feedback can negate the need for large sampling campaigns and analysis during plant optimisation programs.Citation:Lambert, N, Cox, N and Nicholson, R, 2016. Particle Density Meter, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 245–250 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By J. H. Bilbrey

A recording thermobalance ,vas used to determine the rates of oxidation of mol-ten tin over the temperature range 550°-900° C. Oxidation rates were found to vary widely for a given temperature, as previously reported by other investigators. 1 X-ray diffraction data indicated that the probable cause of these variations was the development of preferred orientations in the crystals forming the oxide film. No reasons for the differences in degree of preferred orientation were discovered. For relating the weight of the oxide formed (w) to the time of oxidation (t) an equation of the form wn = kt was found to best represent the experimental data. INTRODUCTION In the course of conducting investigations on the feasibility of using selective oxidation techniques for the purification of various metals in the molten state it was soon discovered that data on the oxidation of molten metals and alloys were very scarce. In contrast to the many hundreds of publications on the oxidation of metals in the solid state there are relatively few articles on the rates of molten-metal oxidation. In view of this scarcity of data, it was decided to institute a series of investigations into the oxidation processes of molten nonferrous metals and alloys with the expectation that the information derived could be put to practical use in developing and improving refining processes based on selective oxidation. This report is the first of a series in which oxidation data for molten nonferrous metals and alloys are presented.

Jan 1, 1955

By J. K. Grunig

A process consisting of leach, continuous countercurrent decantation, resin-in-column ion exchange, evaporative crystallization of beryllium sulfate, and decomposition of the sulfate was developed for Spor Mountain, Utah, ores. The process is metallurgically sound, has a minimum of process steps, and is applicable to a wide variety of beryllium ores. The most novel aspect of the process is a resin system of ion exchange which is highly selective for beryllium and which rejects substantially all impurities except for minor amounts of aluminum, magnesium, fluorine, and sulfate in addition to beryllium. The oxide from sulfate decomposition meets specifications of potential users.

Jan 1, 1982

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Sometimes standing supports are used as a tool to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for different types of standing supports (steel and timber) to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. In this paper, the mine roof simulator (MRS), at the NIOSH Pittsburgh research facility, was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. To justify the testing program for testing standing supports with end-conditions of rock-like materials, the verified prop models were used to study the effect of a wide range of roof and floor materials (gray shale, shale, and claystone) on the critical buckling loads of the steel props. Also, several lateral loading scenarios were evaluated in which the steel props were laterally loaded at different heights. The critical buckling load for steel props setting up against a claystone roof and floor was found to be one-half of that shown by the MRS test where roof and floor platens are made of steel. Minimum prop performance was observed when the lateral load was applied at the mid-height of the steel prop, especially at small lateral displacement (less than 2 in).

Sep 10, 2022

By G. A. Beiswenger

The application of the law of supply and demand to the sale of crude oil is generally conceded, but the motives underlying the buyer's (refiner's) demands are not always obvious to the seller (producer). In some cases this obscurity has led to the conclusion that the refiner may be unnecessarily particular when he selects one crude and rejects another. This preference, however, is very largely the reflection of the refiner's product demands and the quality of the stocks obtainable from the selected crude. The purpose of this paper is to point out critical characteristics of the major classes of refined products and to show how crudes vary in their suitability for such products. With relatively few exceptions, available processing methods and addition agents make it theoretically possible to produce any type of refined product from any crude source, although it may not be economi-cally sound to do so. The widespread application of thermal cracking for converting higher boiling stocks into gasoline is well known. More recently cracking and refining in the presence of catalysts9 have been developed, as well as various processes for polymerizing lighter hydro-carbons into gasolines having desirable characteristics.6 For several years, selective solvents have been applied commercially to refining inferior quality kerosene, Diesel fuel and lubricating oil distillates .3 Improved methods for refining lubricating oils from crude residua,4 formerly suitable only for fuel, are now in use and a number of special solvent processes are available for dewaxing lubricating oils to low pour point.5 These improved refining methods have been developed not only to meet the demand for improved product quality but also to enable the refiner to obtain quality products from crude sources that would not yield such products by the older refining methods. In many cases, the utilization of these modern refining tools necessi-tates an appreciable expenditure for equipment as well as added manufac-turing costs, and their application therefore must be justified economically. Despite the availability of such tools, the added processing costs involved and yields obtainable may render their application entirely impractical. To illustrate this point, inspections of typical cuts from various crudes

Jan 1, 1940

By G. H. Cutter

SAFETY in mining depends on wire rope to as great, if not greater, extent than in any other industry. Sudden failure of a shaft-hoist rope might easily result in death or serious injury to the operators and workmen, extensive damage to expensive equipment, and a loss in production while repairs are being made. A wire rope is only as good as its component parts. It must be made from wire properly drawn and treated. It must be fabricated on machines large enough and capable of imparting the necessary qualities to meet the stringent service conditions. However, unless the fundamental requirement of good ropemaking is recognized, all other operations, no matter how carefully performed, will not impart reliability and quality to the product. This fundamental requirement is steel that is homogeneous, of high resistance to fatigue, and of a type suitable for rope wire. Most wire-rope manufacturers agree that rope wire should be made from acid-open-hearth steel. It is comparatively easy to meet the same physical properties with basic steel, but such properties are only part of the requirements for good wire. It is absolutely necessary, particularly for rope service such as mining, where reliability is essential, that the wire be uniform throughout its entire length. Most manufacturers feel that this highly important requirement is better met by acid-open-hearth steel.

Jan 1, 1936

By L. D. Boughton

Solution mining projects are conducted through one or more boreholes which penetrate en ore body. Proper drilling, completion and maintenance of the boreholes, therefore, is essential to the success of any solution mining operation. Wells drilled for solution mining encounter problems quite similar to problems encountered by the petroleum industry in drilling, completing and maintaining wells for the production of oil, gas or water. Many of the services developed and much of the experience gained by the petroleum industry is applicable to solution mining wells. As in the petroleum industry, each individual wellbore and ore body in a solution mining project provides its own problems. These vary greatly from well to well, and it is not possible to set down data or outline programs that will apply to all wells. Instead, the design of the drilling, completion, production and maintenance programs should be worked out for each individual well. The purpose of this paper, then, is to generally describe materials, equipment and techniques available for these programs and to discuss the purpose and sequence of their use.

Jan 1, 1971

By A. R. Barnes, N. Stubina

Increasingly, gold producers are forced to treat ever more refractory ores. While ores containing pyrite, arsenopyrite and carbonaceous material have been subjected to complete pressure oxidation (PDX) as the standard process for such ores, recent improvements in fluid bed roasting technologies have led to a resurgence of interest in roasting as a viable alternative. The lower capital and operating costs of roaster installations add further impetus to this trend. The Extractive Metallurgy Group at Xstrata Process Support operates four fluid bed reactors of various sizes which have been utilised on a large number of projects to treat highly refractory ores. Preliminary mineralogical modelling of both the physical and chemical aspects of the roasting process and subsequent testing under carefully controlled conditions has allowed clients to obtain gold recoveries approaching or matching those achievable by PDX. The flexibility of the units to operate in various modes- " bubbling bed", circulating bed, two stage, sub-stoichiometric and combinations of these, and the range of sample sizes accommodated, from a few kilograms to a few tons, has enabled XPS to accommodate clients with a wide variety of gold bearing refractory ores from all over the world. This paper outlines the key challenges of fluid bed roasting of refractory gold ores, describes the methodology used to design the testwork program and provides some results from select test campaigns.

Jan 1, 2011

By W. H. Blauvelt

THE subject of fuel-briquetting has attracted much attention on the part of engineers and investors for the past 15 or 20 years, and especially in recent years, during which a number of plants have been built, with more or less commercial and technical success. Our technical literature contains numerous descriptions of certain processes, and discussions of the industry in general. For a history of the development of the art in the United States, and for descriptions of many of the processes which have been tried, reference may be made to the files of our Transactions, and, for more recent information, to a paper by C. T. Malcolmson, read before the First Annual Convention of the International Railway Fuel Association in June, 1909. The purpose of the present paper is to describe the briquette-plant of the Solvay Process Co. and the Semet-Solvay Co. at Detroit, Mich., which, after a period of long and costly evolution, is now operating satisfactorily on a commercial basis. I believe that it will be of interest to some of our members to have the details of operation, lower-consumption, labor, etc., as worked out on a practical and commercial scale in a going operation. The briquette industry has had a somewhat checkered career in the United States, and much the larger portion of the failures has been due entirely to commercial causes. It seems axiomatic to say that before undertaking the installation of a plant for manufacturing briquettes it is necessary that the local situation should be carefully examined : First, to determine the kind of briquettes, if any, the local market will consume; that is-to say, whether the available fuel-supply is such that briquettes would be a welcome addition, and whether the most promising field is the industrial or the domestic market. Second, if there is an available supply of raw material, as coal,

Mar 1, 1910

By Hans Adden, Anne Lehan, Markus Thewes

"1. INTRODUCTION AND MOTIVATION Traditionally design processes are focussed at creating new tunnels for lowest building cost. But the trend towards sustainable constructions in tunnelling has greatly increased in recent years. A critical subtask of this approach is to realize the potential for optimizing and reducing the life-cycle costs (LCC) of tunnels and their components. To evaluate underground infrastructure projects from an economic point of view is therefore a highly topical subject of public authorities as well as private companies participating in Public Private Partnerships (PPP) projects. Nowadays, in the case of public works contracts, the contracting authorities shall draw up rules not only for the design but also for life-cycle costing. Within the scope of the decision-making process of building a new tunnel, planning the maintenance activities or the refurbishment of a tunnel in operation, the decision-makers need detailed knowledge about the current and future financial conditions of the planned projects and selected sub-measures. But in practice, the initial costs still represent the primary decision criterion in the planning phase, whereas the subsequent or follow-up costs, respectively, are only estimated roughly. Although tunnels are the key components and the most costly parts of the transport infrastructure, only a small number of scientific papers deal explicitly with the calculation of life-cycle costs for underground infrastructure. And in these cases, most authors use as the starting point only the basic form of the Net Present Value method which is known as the frequently applied life-cycle costing technique in building construction. The present study explains the strategic concept of life-cycle costing and its fundamental instruments for operational implementation. It shows the necessity to take into consideration that there are fundamental methodical problems when the life-cycle concept is transposed without modifications from building construction to civil engineering. The paper will discuss in detail some selected associated problems with the net present value method. On the basis of operational and safety related tunnel equipment it is shown, what impact this may have on principle determining the LCC of tunnels. Selected best-practices of maintenance planning for tunnels undertaken by the German Ministry of Transport fill the theoretical approach of the concept with life and give a practical orientation. In particular government authorities but also construction companies are interested parties in modern cost management considerations. The reason for this development is the replacement of aged excisting structures and the advancement of technical standards. The increase in the total numbers of tunnels (Fig. 1) as well as the need for future re-investments in existing tunnels show the overall economic impact and justify the change towards the life-cycle perspective."

Jan 1, 2016

By J Arola, B Kettunen, W M. Bond

Separation of fine and coarse particles as separate streams prior to flotation, and their differential treatments, could substantially increase recovery and reduce collector consumption. A series of simulations was carried out to quantify the benefits from plant scale implementation of such a treatment at the Ispat Inland flotation circuit (Minorca mine). The study involved detailed plant sampling and sample analysis to generate the data needed for simulation studies. Samples were taken from all the streams from flotation feed to final concentrate, as well as cell lips and cell pulp. Sampling was repeated for the second ore blend that was processed by the plant during different periods of a year. Sample analysis involved sieve analysis and size by size chemical analysis for total iron, magnetic iron and silica. Raw data were mass balanced, and flow rates within the circuit were calculated. Mass balanced data were used to calculate model parameters representing the existing conditions. Usim Pac was used for both mass balancing and simulation studies. Available pilot and bench scale data were utilised to define the modified flow sheet and expected performance. The simulated flow sheet included classification of flotation circuit feed by hydrocyclones. While the coarse fraction followed the existing flow sheet, the fine fraction was sent to a magnetic separator. Magnetic and rougher flotation concentrates were combined to form the final concentrate. Two simulations for each blend were carried out. The first one assumed that there would be no change in size by size kinetic behaviours of both gangue and magnetite due to this modification. This was named as the worst case scenario, in which particles had a longer residence time due to reduced flow rates within the flotation cells. The second scenario anticipated that there would be an increase in recoveries of gangue and magnetite going into froth launder due to more efficient use of collector in absence of fines. Results showed that pre-classification of flotation feed could improve the flotation recovery by 0.3 - 0.5 per cent, with the major benefit being significant reduction (40 - 60 per cent) in the amount of collector used.

Jan 1, 2005

By G. A. Beiswenger

The application of the law of supply and demand to the sale of crude oil is generally conceded, but the motives underlying the buyer's (refiner's) demands are not always obvious to the seller (producer). In some cases this obscurity has led to the conclusion that the refiner may be unnecessarily particular when he selects one crude and rejects another. This preference, however, is very largely the reflection of the refiner's product demands and the quality of the stocks obtainable from the selected crude. The purpose of this paper is to point out critical characteristies of the major classes of refined products and to show how crudes vary in their suitability for such products. With relatively few exceptions, available processing methods and addition agents make it theoretically possible to produce any type of refined product from any crude source, although it may not be economically sound to do so. The widespread application of thermal cracking for converting higher boiling stocks into gasoline is well known. More recently cracking and refining in the presence of catalysts9 have been developed, as well as various processes for polymerizing lighter hydrocarbons into gasolines having desirable characteristics.6 For several years, selective solvents have been applied commercially to refining inferior quality kerosene, Diesel fuel and lubricating oil distillates.3 Improved methods for refining lubricating oils from crude residual4 formerly suitable only for fuel, are now in use and a number of special solvent processes are available for dewaxing lubricating oils to low pour point.5 These improved refining methods have been developed not only to meet the demand for improved product quality but also to enable the refiner to obtain quality products from crude sources that would not yield such products by the older refining methods. In many cases, the utilization of these modern refining tools necessitates an appreciable expenditure for equipment as well as added manufacturing costs, and their application therefore must be justified economically. Despite the availability of such tools, the added processing costs involved and yields obtainable may render their application entirely impractical. To illustrate this point, inspections of typical cuts from various crudes

Jan 1, 1940

By B Wong, R G. Coleman

In flotation, the selection of the size, number and type of cell for a particular duty depends on two important factors. Firstly, the required flotation residence time and secondly, the physical constraints of how much concentrate can be recovered for a given froth surface area and concentrate lip length. The residence time is influenced by ore type and characteristics such as liberation, kinetics and reagent dosage. The amount of concentrate that can be recovered for a given froth surface area and lip length depends on ore type and other characteristics such as particle size, specific gravity and mineral grade. Residence time is determined through a combination of laboratory-scale test work and design scale-up factors. However the critical froth transport parameters such as froth carry rate and froth lip loading cannot be determined in a laboratory. This is because the froth is scraped during a laboratory flotation test and thus does not exhibit natural behaviour, and it is not possible to scale-up froth transport distance or air rate. These values are generally compared via calculation to rule-of-thumb maximum values to establish if these values will be exceeded by the flotation cell selection.This paper first reviews these critical froth transport parameters and then discusses actual parameter values across diverse operating sites, with varying cell duties, cell sizes and types, orebodies and particle sizes. These values are compared against the industry rule-of-thumb to test the applicability of the rule-of-thumb to actual performance. Options are also presented for adjusting these parameters in operating flotation cells.CITATION:Coleman, R G and Wong, B, 2018. Flotation launder design and the measurement of critical froth transport parameters, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 353–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By I Gipps

Each of us has a vision of what the future mine will be and, generally, these visions have many similarities and some differences. One of the major discrepancies in visions of the future mine is not the ultimate goal but the path to achieve it. Many of the future concepts require a radical re-thinking of how things are and will be done yet. So how do we reach this visionary future mine? We need a path that satisfies both our future aspirations of a high tech gee-whiz operated from our iPads and the unfortunately mundane approach that says ‘we must know the method works, ie nothing new’.This paper explores how, within a research based organisation, we firstly set our ultimate goal and then divide the path into realistic technology development chunks that would appeal to mining companies to progress within their organisational constraints. Through examples, such as, automated LHDs, communications systems, surveying and localisation, rock cutting and geological sensing, we illustrate how this path will get us from the here and now to the out there future.This paper also demonstrates CSIRO’s short, medium and long-term research in many of the areas needed to create the Future Mine: mining methods, automation and remote control, mine communications, mapping and mission planning, geological sensing and, importantly, human-system integration, which examines how to effectively present data as information to operators and supervisors in an intelligent and useful manner.

Nov 22, 2011

By M Jacobs

This abstract discusses a heap leach copper mine that was failing to perform and as a result was not meeting targeted production. The mine had numerous technical challenges including: high water inflows, low levels of geotechnical monitoring, performance issues with mining, resource model and grade control reconciliation issues, and unexplained low levels of performance from the heap leaching operations. A team from various organisations with specialist skill sets including: a forensic accountant, the owner’s representative and a mining engineer, was arranged to visit the site. The task was to investigate the situation and determine what could be done to turn the performance of the mine around. After an initial assessment in late 2018, efforts were directed to better understanding the operations and improving the performance of the site through preventative management. A key part included the creation of production forecasts that could be achieved that would help restore confidence in the operations. Uncertainty in the mine achieving production forecasts and the performance of the heap leaching operations were contributing to the decline of the operations. Investigations uncovered the fact that while the resource model could reliably predict total copper, a lack of sequential leach data meant the accurate prediction of soluble and insoluble copper species, both important for heap leaching, was difficult to do with any degree of certainty. The crushing and mining contractors also appeared to have suffered somewhat from a lack of management by the owner’s team and performance had affected the production of copper. Collaboration and management were used by the team to understand and stabilise the operations. Ongoing collaborative efforts by the management team, site personnel and contractors resulted in a positive outcome for the owners and their mine – and could at yours.

Jun 22, 2022

By III Scotland

Genstar's underground mine at Texas, MD experienced a failure of the mine roof and subsequent damage to an underground backfill caused by surface floodwaters. A hydraulic backfilling program was developed in house to stabilize temporary repairs to the mine roof, replace 2300 yards of pneumatically stowed backfill, and complete a permanent repair to the mine roof. A flowable backfill material was developed, tested, and later marketed as the result of experience gained during this project. In addition, Genstar personnel developed backfilling techniques to meet the requirements of the repairs and completed work without the additional expense of non company services or contractors.

Jan 1, 1992

By Md. Maniruzzaman

The quenching performance of a liquid quenchant can be controlled by controlling the agitation in the quench tank. Without agitation, a vapor layer or bubbles form at the hot part surface and the natural convention of the quenchant limit the heat extraction rate at the quenched part surface. Resistance to the heat extraction rate can be reduced by breaking the vapor layer or by inducing a turbulent convection at the part surface through agitation (Le. forced circulation of the quenchant). To determine the effects of agitation on the quench performance of a mineral oil based quenchant, the CHTE quench probe system was used with AISI4140 steel probe tip. Quenching performance of the oil is evaluated by computing the effective heat transfer coefficients of the steel probe as a function of surface temperature using Lumped Parameter Analysis. In addition, computational fluid dynamics (CFO) simulation of the quench tank with an impeller type agitator has been done to understand and predict the fluid flow pattern in the tank. CFO simulation also provides insights for determination of optimal location of the impeller and the quench probe tip. Keywords: CHTE Quench Probe, agitation, CFD simulation, liquid quenchant, 4140 steel

Jan 1, 2003