Search Documents

By Tapan Goswami, Lloyd Hain, Geoff Brent

For many years Ramp 24 at Ensham mine in Queensland, Australia has suffered substantial coal loss and damage due to the fragile nature of the coal and problematic geological conditions, which have proved very challenging. In the past various blasting techniques were applied in attempts to improve coal recovery. One approach was to use a shallow throw (cast) blast followed by a separate post-strip blast underneath. Another method was the introduction of the practice known as “baby decking” with the addition of a large buffer of material in front of the coal. However, despite increasing mining costs, none of these techniques adequately reduced coal edge loss and damage.

Jan 1, 2008

By D. Jean Hutchinson, Mark Diederichs

"Cable bolts are an important support component in modern underground mines. If an optimized cable bolt system is to be achieved, it is insufficient to focus on cable bolt layout design or on cable bolt installation in isolation. Cable bolt support, like all engineered systems, requires a holistic approach, encompassing integrated elements of design, implementation and verification. The “Cable bolting Cycle” described in this paper incorporates these components along with related tools and procedures which should be used together to ensure effective and efficient cable bolt support.Design involves the consideration of demand, capacity and constraints as outlined in this paper. The demands imposed on the sup-port system by the rock mass response to excavation under the combined action of stress and gravity must be matched to the capacity of the cable bolt array. The cable bolt system capacity is a function of the component strengths of the steel strand and the bond (load transfer) and by the deformation response and retention characteristics of the system. The design is bounded by operational and economic constraints.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.The information presented in this paper represents a very abbreviated version of much broader concepts, procedures and design charts, presented in a practical cable bolting handbook by Hutchinson and Diederichs (1996)."

Jan 1, 1996

By L. Yuan, A. C. Smith

MFIRE, the mine-fire simulation program of the U.S. National Institute for Occupational Safety and Health (NIOSH), is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines. MFIRE has been used by U.S. and international companies to simulate fires for planning and response purposes. It is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence, such as changes in ventilation parameters; external influences, such as changes in temperature; and internal influences, such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the former U.S. Bureau of Mines in the 1970s, several updates have been released. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated Fortran programming language was replaced with an object-oriented C++ language and packaged into a dynamic-link library. However, the MFIRE 3.0 release included no change or improvement to the fire-modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire-modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of the t-squared fire as a new fire-source model and the ability to include available heat-release-rate versus time data, the addition of a moving fire source for conveyor-belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke-rollback phenomena. All of the improvements discussed in this paper will be included in MFIRE 3.1 and released by NIOSH in the near future.

Jun 1, 2016

By Derrick Chambers, George Kevin Chapin, M. Shawn Boltz

Seismic monitoring is one of the few noninvasive technologies with the potential to provide sub-surface geomechanical information to operators of large open-pit mines. Although passive seismic data has been used to refine emerging failure geometries and provide advance indication of surface deformations in the literature, doing so reliably in an operational context is much more difficult. This is due in part to difficulties in estimating and interpreting source locations and parameters in complex, low-stress open-pit environments. Additionally, the high costs associated with implementing, operating, and maintaining deep borehole seismic networks, which are most commonly used to monitor large open pits, can be difficult to justify, especially if monitoring benefits are not readily apparent. In this study, we explore the use of a near-surface nodal seismic deployment, which is commonly used in oil and gas exploration, for monitoring open-pit mining-related seismicity on a short-term basis. A deployment of 18 geophones was conducted on the surface in and around the Bingham Canyon Mine, a large open-pit mine near Salt Lake City, Utah, USA, where we find the small seismic array can detect and locate a variety of mining-related seismic sources, even with an extremely simplified velocity model. We outline the process of creating an idealized velocity model, developing a local magnitude scale, and interpreting the observed seismicity. Of note, we analyze a sequence of mining-induced events associated with a known structure on the south pit wall. We conclude with discussion on how surface-based deployments may be used to augment, or in some cases supplant, borehole seismic networks at large open-pit mines depending on monitoring requirements and objectives.

Apr 26, 2022

By I. Silin, H. Wotruba, J. Huben, A. Ognyanova

"With increasing shortage of raw materials, the beneficiation of ultra-fine ores will play a larger role in the near future. Many established process technologies do not yield satisfactory separation results for ultra-fine materials. Without selectivity, high-grade concentrates cannot be produced. The material at hand is a taconite which had to be ground to d(90) = 25 µm to guarantee liberation of the iron oxides. The comminution was done by High Pressure Grinding Roll (HPGR) and resulted in smooth surfaces and clear grain boundaries. This is an indication of selective grinding and mineral liberation. Further processing steps included selective desliming, magnetic separation as well as reverse flotation. INTRODUCTION During the last centuries, the processing of iron ores became increasingly important. The coarse-grained, so-called lump ores that are ready for direct usage in blast furnaces without further processing are becoming gradually less abundant. The processing of ultra-fine-grained ores, which in addition require a complex ore beneficiation due to the composition of the material, will progressively gain relevance with increasing resource shortages in the future (Arvidson, 2013). The term “ultra-fine” does not hold a precise definition in mineral processing. In this paper, “ultra-fine-grained” ores are defined by the required grind size for full liberation smaller than 20 µm. Many established mineral processing technologies do not yield satisfactory separation results for ultra-fine materials. Thus, they are limited in their application to produce high-grade concentrates suitable for sintering and pelletizing for direct reduction processes. The production of a high-grade iron concentrate (over 68% Fe) with low silica content (under 2.5% SiO2) is possible from both magnetite and hematite containing ore. In addition to the mineral processing technologies (magnetic and gravity separation, flotation), technologies for the liberation of fine-grained iron ores need to be developed and improved. In contrast to the conventional wet grinding circuit by means of tumbling mills, several future trends in dry and wet grinding and regrinding are already in use. These include technologies such as vibration mills (Palla®Mill), stirred media mills (Vertimill®), vertical roller mills (Loesche) and high-pressure grinding rolls (HPGR) (Jankovic, 2015). This study preliminary investigated the mineral processing of a low-grade, ultra-fine-grained, complex iron ore in a laboratory scale after dry grinding by HPGR to 90% < 25 µm without consideration of the grinding, milling, energy and classification cost."

Jan 1, 2018

By WALTER M. DAKE

GENERALY speaking, the bituminous coal mines of the country are being operated at a loss. To purchasers of the necessary commodity, a statement of this character may have the sound of a far fetched propagandist cry; but to the coal producer who lives in the hope of an up-turn in the almost stationary market price of his product, while inking in red his monthly operating balances, it carries the ringing sound of truth.

Jan 1, 1925

By Robert C. Stanley

Early History Probably the first use of nickel by man was in the fashioning of implements, and later swords, from nickel-bearing meteorites, masses of metal that have fallen from time to time at many points on the earth&apos;s surface and which consist normally of iron carrying substantial amounts of nickel. Meteorites were perhaps the first metal known to man. The falling star, sought out with fear overborne by curiosity, was found to be a better stone than the earth-given, truly a boon from the gods. Archeologists tell us there is good evidence that the ancient oriental peoples learned at an early date to make these stones into useful implements. The invincible blades of the great warriors of old in China, Persia, and in northern Europe, were Heaven-sent, a fable which sounds significant of meteoric iron. Probably some of the ancient swords of Khorassan and of Damascus were of meteoric nickel-bearing iron (1). Fifty centuries were to pass before men learned to isolate nickel and add it to iron to produce the same alloy for much the same purpose. Meanwhile, man had found another natural alloy of nickel, known first to the Chinese as paktong, or &apos;white copper.&apos; It was obtained from complex copper-nickel sulphide ores of Yunnan in southern China. This metal was brought by caravan through India into Bactria, a country north of the Hindu-Kush mountains, in what is now known as Russian Turkestan. The earliest specimen extant is a Bactrian coin attributed to 235 B.C. The rough reddish-white metal was also sent in the form of triangular rings to Canton, where zinc ores were added and the whole smelted to a more malleable alloy, also known later as paktong. This alloy was the forerunner of German-or nickel-silver. Specimens of this alloy, wrought into ornamental candlesticks and boxes, were brought from Canton to Europe by the East India Company in the early days of the China trade. Paktong was highly prized for its beauty as well as its eastern origin in far-away China. By 1760 the unwrought metal was imported into England for domestic manufacture.

Jan 1, 1935

Blast vibrations induce sounds within neighboring residences. A house wide vibration and sound monitoring system was installed in a West Virginia home which was subjected to blasts at varied distances and direction. Eighty-nine blast events were monitored and analyzed for this case study. Fifteen channels of data were collected including three triaxial geophones, one airblast microphone, one uniaxial geophone mounted to the wall of the house (response channel), and four microphones that recorded CD quality sound waves inside the house. Each of these channels was recorded on the same time reference and scale allowing for direct comparison of the waveforms. The response channel signal was easily separated into ground vibration induced and airblast induced movement due to the differences in their times of arrival. This response channel was then compared to the sounds recorded inside the home to determine which component of blast vibration induced the maximum sound response inside the home. Blasts at distances less than 762 meters (2,500 feet) had maximum sound responses from both ground vibration and airblast. While for blasts beyond 762 meters (2,500 feet), the maximum sound response inside the home was caused by ground vibration without exception. When airblast was identified as the dominant sound generator in the house, the peak amplitude of the sound was directly related to the amplitude of airblast. When ground vibration was identified as the dominant sound generator in the house, the peak amplitude of sound was not related to the amplitude of ground vibration. In these cases, sound amplitude was driven by the conditions present in the house such as loose items, doors, and windows creating sudden peaks from falling or slamming. In the same respect, sound amplitudes varied depending on where the sound was recorded. Different rooms generated very different sounds based on the contents of the room. Findings from frequency analysis showed that the frequency content of sounds inside the house were not related to frequency content of airblast or ground vibration regardless of source suggesting that residents would have difficulty determining the source of blast induced noise in their homes.

Jan 1, 2010

By W. O. Vanderburg

The leasing or tribute system has been an important factor in the development of our metal-mining industry, particularly in the gold and silver mines of the Western States. It has received its widest application in. the early history of many camps and in the last stages of many mines. The system is especially adapted to mining where the ore&apos;s occur in narrow veins or are erratically distributed in small bunches or pockets so that selective mining, hand sorting, screening, or hand cobbing is required to produce shipping or milling-grade ore. The leasing system is also applicable to the development of prospects where the owners are unable or unwilling to assume the risks of searching for ore. The virtue of the system lies in the opportunity it affords miners with little capital to get started; at the same time, it rives owners an opportunity to have their property developed at small cost.

Jan 1, 1934

By S. q. Honingh, G. Van Weert

Currently produced zinc-enriched blast furnace dust is stored on site at CORUS IJmuiden. To end this practise, a research program was started in 1996. Four technologies were studied: oxidative autoclave leaching in a chloride medium, fluid bed pyrohydrochloridisation (pyrohydrolysis) to yield lead-zinc-free (hematite) calcine, EAF (plasma) smelting/zinc fuming, and incorporation of the dust in 'iron foundry cupola charges. All aim to remove zinc and lead, recycle the iron residue internally, and produce a saleable zinc-lead product.

Jan 1, 2000

By Filippos Patsiogiannis

Laboratory size (5 kg) aluminum killed low carbon steel melts were desulfurized with synthetic fluxes in zirconia crucibles. The sulfur, oxygen, aluminum, silicon, and manganese contents in the melt were determined as a function of refining time and temperature. With a good argon shield and synthetic flux cover, melt reoxidation was not observed. Sulfur removal followed first order reaction kinetics. The effectiveness of calcia saturated calcium-aluminate (12CaO.7Al2O3) based fluxes in desulfurizing the steel melts was evaluated. The effects of initial sulfur level of the melt, weight of the flux (slag), and additions of tellurium, fluorspar, and barium oxide to the melt on the kinetics of desulfurization were also studied.

Jan 1, 1993

By Alan E. Renshaw

"This paper is a practical overview of ways to reduce cost in the design and operation of an Arctic mine. The economically important issues of the Arctic mine that will be addressed include: permafrost and the active zone in general terms; road building in and over permafrost; Arctic geotechnical mine design considerations; pit dewatering techniques in sub-zero temperatures; and blasting frozen materials with techniques to obtain optimal results. A final section on a few special topics conclude this paper.Although this paper primarily refers to near surface conditions more closely associated to an Arctic surface mine, many of the ideas and techniques contained in the paper also apply to the surface construction of an Arctic underground mine."

Jan 1, 1996

By J. D. Christian

WHEN mining development began in the Kirkland Lake camp, twenty-five years ago, there was very little information obtainable from surface showings as to the nature of the ore deposits. A length of almost a mile of the main &apos;break&apos; lay under the south arm of the lake, and elsewhere most of the outcrops were covered with glacial drift. Shafts were sunk on ore-bodies of uncertain value, either on the outcrop of the veins or-because of the lake to the north-in the south or hanging-wall. In the second year of the camp&apos;s development, the Great War broke out and retarded progress for its duration. He would have been a real optimist who, in those early years, could have foreseen mining at depths of more than a mile.

Jan 1, 1939

By Gordon J. Hughes

The ldaho Cobalt Belt represents a unique geologic environment containing some of the largest known reserves of cobalt in the United States. Stratabound cobalt-copper-gold deposits formed within a sedimentary basin that was generated by the rifting of an Archean cratonic block. Host rocks for these deposits are the Early to Middle Proterozoic Yellowjacket Formation comprising a suite of clastic sediments, volcaniclastics, and mafic tuffs that accumulated in the intracratonic rift basin about 1.7 b.y. ago. Rifting was probably initiated during a regional heating and doming event that may date back to 1.8 b.y. ago. During this time, other rift basins were likely to have formed in the region. They probably represent the precursors of a much larger depositional environment having characteristics of an Atlantic- type or passive continental margin where younger formations of the Belt Supergroup were deposited. The Yellowjacket Formation has been subdivided in the Idaho Cobalt Belt into three genetic units representing various subenvironments of a deepwater clastic fan complex. A northwest- trending deep-basin structural trough accumulated fine-grained muddy sediments that were periodically interrupted by distal turbidites of the subaqueous fans. Subsequent progradation caused the deposition of coarser-grained clastics of the more proximal portions of the fan complexes. Submarine fan lobes were built across northwest-trending tectonically active basin growth faults. These in-basin structures caused a great deal of penecontemporaneous deformation within the Yellowjacket sequence. Northeast-trending fault zones formed an orthogonal set of fractures that controlled the shape and size of sub-basins, and were also an influence on lateral migration of dominantly fine-grained clastic material. The eruption of mafic tuffs at about 1.7 b.y. ago added a new component to the Yellowjacket sedimentary sequence. Around the Blackbird mine area these tuffs commonly occur either near the base or within some of the sandier sequences. Since most of the sand influxes were largely controlled by basinal tectonism, the tuffs were probably erupted during tectonically active periods of basin development. The dynamic nature of the sedimentary environment probably caused much of the tuffaceous component to be mixed with other clastics and even resedimented as volcaniclastic material. In time, the change to a higher energy sedimentation regime resulted in such a dramatic clastic dilution of the tuffs that they could not survive in the areas of the vents, and, if present, they must have been distributed elsewhere in the basin.

Jan 1, 2013

By M Reid, H Arbon

Hillgrove Resources (HGO) commenced open pit mining in 2011 and from 2011 to 2016 the geology team experienced a consistent negative reconciliation between grade control estimated copper (Cu) grade and the mill received grade. For the first four years, despite trialling various grade control strategies, the monthly variance between geology and mill copper grades fluctuated between -5 per cent to -17 per cent Cu metal depending on the style of mineralisation.In 2015, HGO embarked on various measures which resulted in changes to grade control practices under the advice of consultants. These changes to grade control sampling, estimation and block out practices resulted in six to seven months of consistently poor Mine to Mill reconciliations from -25 per cent to -28 per cent Cu.In an effort to mitigate these poor reconciliations the geology team reintroduced the preconsultant block out and geology driven grade control methods. Blockout reconciliations from this point emulated those seen originally from -8 per cent to -12 per cent (Cu per cent). Early in 2016 the geology team introduced conditional simulation for grade control as opposed to ordinary kriging to better characterise the grade distribution, introduced separate estimation parameters appropriate for every zone of mineralisation, implemented a maximum profit function to optimise the selection of ore and waste, and retained the geology driven block out processes. Since March 2016 the mine has experienced consecutive months of positive Mine to Mill reconciliations, the first seen in six years. Year to date the expected copper metal is within 1 per cent of mill reconciled copper metal.This paper will compare the various sampling methods, estimation algorithms and block out procedures from the past six years to arrive at a robust open pit operating procedure applicable for mineralisation with high short scale variability.CITATION:Reid, M and Arbon, H, 2017. Setting new standards at Kanmantoo – effective grade control procedures, in Proceedings Tenth International Mining Geology Conference 2017, pp 401–408 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By W. F. Wheeler

IN the study of the coals of Illinois now being carried on by the State Geological Survey, an attempt is being made to determine the most satisfactory basis of comparison between different coals. The following discussion is based upon work done for the survey in the laboratories of the State University and under the general direction of Prof. S. W. Parr. " Pure coal " has been defined by Mr. A. Bement1 as ash- and moisture-free coal, and the use of this " pure coal " as a basis for comparing different bituminous coals has lately been much discussed among engineers in the middle West. By some the B.t.u. of the pure coal is being used to check calorimetric results, and to calculate the calorific value of different coal-samples from the same seam, for which purposes it is necessary to assume-first, that the composition and calorific value of pure coal from different parts of the same coal-seam are uniform, and, second, that these values remain constant after the coal is mined, both of which assumptions there are reasons to believe are inconsistent with the facts. Certain variables are included in pure coal, as ordinarily defined, and disregard of them may lead to serious error. In any event, where delicate shades of difference are involved, no sure interpretation of results can be made, unless these variables be eliminated. As a basis of comparison between coals, ash- and moisture-free coal is much to be preferred to " dry coal," and still more is it to be preferred to " moist coal," as ordinarily reported in analyses. There are, however, two constituents other than ash and moisture which are similar in effect to them, and which

Jan 1, 1908

By Pinnaduwa H. S. W. Kulatilake

A new formulation is given to conduct a probabilistic block theory analysis. A new computer code (BTAC) has been developed to perform both deterministic and probabilistic block theory analyses. The variability of the discontinuity orientation and shear strength is incorporated in the probabilistic block theory analysis. Discontinuity orientation is treated as a bivariate random variable including the correlation that exists between the dip angle and dip direction. BTAC code was applied to perform both deterministic and probabilistic block theory analyses for a part of an open pit mine in the U.S. Needed geological and geotechnical data for the analyses were obtained from field and laboratory investigations. The variability of the discontinuity orientations resulted in important differences between the probabilistic and deterministic block theory analyses results. The results confirmed that the design value selected for the Maximum Safe Slope Angle (MSSA) for a particular region in the open pit mine based on the deterministic block theory analysis can be on the unsafe side. In summary, the results showed clearly the superiority of probabilistic block theory analysis over the deterministic block theory analysis in obtaining additional important information with respect to designing rock slopes.

Jan 1, 2014

By Feida Wu, Yuhang Liu, Huimin Gao, Yuhan Song, Zhi Liu, Zijie Ren

In the process of quartz purification by calcination water quenching, the different expansion rates of gangue minerals and quartz were used to produce cracks or remove fluid inclusions, which is conducive to subsequent purification. However, the role and mechanism of calcination-water quenching are still lacking in research. In this paper, the position of calcinationwater quenching in gangue quartz purification process was adjusted and the removal effect of calcination-water quenching process at different nodes in the process was explored. The results show that the purification effects of grinding-calcinationwater quenching-classification-acid leaching process and grinding-classification-acid leaching-calcination-water quenching process were relatively good. The main reason is that calcined water quenching can make quartz produce cracks, which are more rough. At the same time, calcined water quenching is located after grinding, which has a larger specific surface area, pore volume and pore diameter, and has a strong adsorption capacity for acid solutions.

Nov 2, 2023

By A Riles

"Three issues of relevance in a modern tailings storage facility (TSF) are:geotechnical stabilitymanaging acid rock drainage (ARD) from pyritic tailingsmanaging the tailings from cyanidation of gold ores. Drawing on examples from both copper porphyry flotation and sulfide-hosted gold ores, this paper demonstrates that giving some weight and importance to the process tails properties upfront can influence the flow sheet and not only improve tailings management effectiveness but also impact positively on economics. In the case of a typical copper porphyry ore with moderate pyrite content, the rougher tail in a conventional high pH selective flotation step is usually classified as potentially acid generating (PAG). To avoid the generation of ARD within the tailings and the requirement for a costly plastic lining, subaqueous deposition is recommended, which in turn has negative implications for tailings stability, consolidation and closure. Adopting a neutral pH rougher stage rejects silicate gangue but recovers pyritic material to the cleaners for a subsequent selective flotation stage, often after regrinding. This effectively quarantines the PAG pyritic material in a much lower volume cleaner tail, which can then be appropriately encapsulated within a larger non-lined flotation tails facility. It also facilitates cyanide leaching of the cleaner tail for gold recovery, with the encapsulated tailings facility being suitable for cyanidation tails storage. A case study from Europe is examined. For gold ores where the gold is sulfide-hosted, but not refractory, a flotation route with cyanidation of the concentrate can similarly produce the majority of tailings as a benign flotation tail and again quarantine the low volume concentrate leach tail in a small encapsulated cell with appropriate residual cyanide management measures applied. Overall economics for intensive leaching of a low volume concentrate stream can also be surprisingly positive. A feasibility study design example of the process and TSF is presented. CITATION: Riles, A, 2016. An Integrated Approach to Optimising All Concentrator Products, Including Tailings, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 341–346 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By R Osterman

As mining companies have to go deeper in search of ore and coal, the importance of protecting the highwall increases. Wall fatigue also increases with importance of the long life expectancy of a highwall, in particular the impact of fatigue influenced by resonance. Resonance is the tendency of a material to oscillate with greater amplitude at certain frequencies when exposed to a periodic force. Until recently, only dominant frequencies, either natural or induced, were all that could be measured through the fast Fourier transform of the blast-induced wave form.This paper presents a novel method to accurately predict the resonant frequency of a highwall. In fact, the method can predict the natural frequencies between any two monitoring points placed in line with the source of impact, and as such it can be used to determine the resonant frequencies of any physical object. The method not only predicts the resonant frequencies of the material; it predicts the structural response of the total frequency spectrum. This method helps describe the response of a mechanical structure to excitation. It describes the structure’s efficiency in the use of energy, that is, whether energy is dampened or consumed in resonance.The initial predictions have been so accurate that it made it possible to determine the fundamental frequency and the first six harmonics of a highwall in a northern Queensland coalmine. With the use of electronic detonators, the blast can be timed with a repeating delay to create an induced artificial frequency that has been determined to retain the least amount of energy.CITATION:Osterman, R, 2015. Transfer function – new method to accurately predict resonant frequencies of a highwall, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 233–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015