Search Documents

By M. K. Barnett

[ ] ENGINEERING research consists, broadly speaking, in the investigation of the effect of the variations in a number of factors on some property of a product or characteristic of a process. The unambiguous description of the product or process requires that the property or characteristic be expressible in quantitative terms. For the purpose of practical control, it is likewise desirable that the independently variable factors governing the product or process be quantities, although this ideal goal is not always attained. Maximum efficiency-i.e., the attainment of the maximum amount of reliable, useful information relating to the influence of the factors on the property of the product or characteristic of the process, for the least expense-is an important requirement for the satisfactory operation of a research organization. Obviously, a necessary condition for the attainment of maximum efficiency is an adequate knowledge of the specialized field in which the experimental research lies. While necessary, this condition is not sufficient. Proper attention must also be given to the general principles of experimental design together with the modem methods for the analysis and evaluation of experimental data. The present discussion is confined to a single design, the so-called "factorial" design. This design is of special interest in that it attains its goal, maximum efficiency, by directly departing from the

Jan 1, 1947

By Edgar Kendall

A KNOWLEDGE of the fundamental principles of locating, sampling, testing and evaluating materials is essential in prospecting for mineral aggregates. In this discussion, mineral aggregates will be considered sand, gravel, crushed stone and slag that are used as materials of con-struction. The quantity of mineral aggregates produced in the United States during the year 1935 for such purposes was roughly 165,000,000 tons, about 60 per cent of which was sand and gravel, 37 per cent crushed stone and 3 per cent crushed slag. The total value of this material was approximately $100,000,000. It is apparent therefore that the prospect-ing for suitable mineral aggregates is of considerable economic importance. In prospecting for mineral aggregates, the methods employed are the same whether the organization is large or small. In the large organiza-tion there may be available geologists for locating sources of supply, a land acquisition department to arrange for the necessary options or permits, engineers to do the sampling, a laboratory for testing, and a board of consulting materials engineers to make the final selection. Even small organizations must follow the same general procedure, though the respon-sibility for the selection of aggregates may rest with one man, who may or may not be an engineer, but who must depend entirely upon his own judgment.

Jan 1, 1939

By John Reynders

Our entry into the World War suddenly brought home to us in a startling way the vital importance of manganese. Since the war, much has been written and said upon the subject of manganese and a great deal of time and money have been spent in attempts to find an adequate substitute for this metal in the manufacture of steel; none has been found. It is true that ways are known by which it is possible to make small amounts of good steel without manganese; but taking into consideration the diminishing quality of iron ores and fuels. as' well as the increasing exaction of specifications for finished products, it may safely be assumed that high-grade manganese ore will be more and. more a necessity in the production of steel as time goes on. Taking world resources as a whole it may be well to point out that the problem of obtaining needed supplies of manganese from a strictly commercial viewpoint is now less serious than it was before the war. Formerly it was feared that world resources of high-grade manganese ore might be exhausted in a relatively short time, but, largely as a result of the stress laid upon the importance of manganese during the war, the world's available supply of high-grade manganese ore has been greatly augmented by new discoveries and fuller development of previously known deposits.

Jan 5, 1927

By L. T. Larson

Had the blank on the Abstract form been sufficiently spacious a more appropriate title for this paper would be: Neogene Tectonism, Magmatic Activity and Hydrothermal Precious Metal Mineralization in Anatolian Turkey; an Analog with the Basin and Range Province of the Western U.S.? Like the alternative title no thing in Turkey is simple. Its history is long and convolute; its culture fascinating; its metallogeny diverse and its geology very complex. This paper will focus only on the geology of western' Anatolia and the precious metal potential of this third of Turkey. The argument is in the article but to save the reader time and suspense I'll put my conclusions up front- the potential is great and the possibilities exciting.

Jan 1, 1989

By J. M. Garcia

This paper highlights several management practices from the oil and gas industry to support the proposition that financial performance in the finite, non-renewable resource business relates more to upstream rather than downstream activities. Based on the analysis of nine oil and gas companies, this study supports a previous study involving fourteen mining companies that showed reserves growth is one of the main levers of value creation in mining. Interestingly, this study also finds that the oil and gas industry has been historically more profitable than mining. The reason, it is argued, is that oil and gas companies count on management practices that focus primarily on the upstream segments of the business, compared to the traditional downstream focus of mining. This paper delves into these ideas to conclude that what mining may need to improve its competitive advantage is a new organizational framework. Another conclusion is that the upstream management focus is vital not only for strategy formulation in the resource business, but also for policy formulation in economies based on the export of finite, non-renewable resources.

Jan 1, 2011

Government geoscience may be categorised by objective under three headings: Applied Research for Geoscientific Framework Studies, Resource Inventory, and Technical Advice. In Queensland, the Department of Resource Industries is active in all three categories. Under the program-based management system adopted in 1987, three Programs, namely, Geological Survey, Mineral Resources Development, and Energy Resources Development and Utilisation, have geoscience responsibilities.Prime responsibility for geoscience resides with the Geological Survey Program, which provides a geoscientific framework for mineral and energy exploration and the development of the State. Simply stated, the Program goal is to provide geological information when and where it is required. Geological Survey work also encompasses aspects of resource inventory and technical advice, complementing the work of the other two Programs. This role has a 122 year long tradition, for geoscientists of the Geological Survey have been engaged in investigations designed to facilitate the identification and utilisation of the mineral, water and energy resources of Queensland since 1868.

Jan 1, 1990

By Alfred Haack, Günter Girnau

INTRODUCTION From 1967 to 1976 in the Federal Republic of Germany about loo km tunnels and 125 underground stations were constructed for municipal and commuter railways solely. Additional a remarkable amount of road tunnels and sewers were built. In 1977/78 a further 27 km railway tunnels, 3.5 km road tunnels and 65 km sewers and utility lines were under construction. This shows an enormous volume of tunnel construction work. In connection with this activity various technical research and development programmes have been carried out. They deal with nearly all fields of underground works as for example soil and ground exploration, excavating and lining techniques, calculation and last but not least waterproofing problems. It is impossible within the framework of this report to touch on all the problems. Therefore, only one problem area with its different aspects will be discussed: waterproofing systems and their last developments in Germany, especially, joint sealing with special consideration of the waterproofing of concrete segmental tunnel lining (1)

Jan 1, 1979

By Jan M. Mutmansky, Y. J. Wang

Mine ventilation analysis is an engineering discipline that can be considered a branch of the body of science known as network analysis. Likewise, the group of engineering procedures known as the critical- path method (CPM) is considered a branch of network analysis. It is therefore not surprising that mine ventilation network analysis and CPM have many similarities. These similarities are useful in analyzing several types of mine ventilation problems and will be utilized in this paper. The analogy between the free split in a ventilation circuit and the critical path in a scheduling network has been recognized by Owili-Eger (1973). While this was recognized as a property of a general ventilation network, many important applications to controlled- splitting problems also exist. The mathematical procedures necessary to apply CPM and network methods have previously been presented (Wang, 1981; Wang, 1982). This paper will illustrate the implementation of these methods by application to mine ventilation networks.

Jan 1, 1982

By D. W. Fuerstenau

Recently R. J. Charles1 showed that comminution of brittle or semi-brittle materials in batch operations is described more appropriately by a variable energy relationship than by the specific relation- ships proposed by Rittinger,2 Kick,3 and Bond.4 That is, the value of n in the empirical differential operation which applies to crushing and grinding (Eq. 1) is variable. Independently, Holmes6 developed an identical generalized equaton for size reduction. The experimental data of Charles and Holmes show that the value of n is determined by the material and the comminuting machine and is constant for a given combination of these two conditions. The general objective of the present article is to extend the Charles-Holmes concepts to continuous ball milling. The specific objective is to analyze the operation of a vibratory ball mill dry-grinding chromite in a continuous open circuit and to develop an equation for the comminution of chromite in this mill.

Jan 12, 1959

By A. M. Lovelace

Introduction One area of engineering utilization of materials in which the requirements are especially rigorous and demanding is that of aerospace systems, including aircraft, helicopters, missiles, and space satellites. Materials used in these systems must reliably perform many critical functions in a broad range of adverse environments. Some of the most critical functions are performed by polymeric nonmetallic materials such as elastomers (rubber), coatings, fibrous materials, and reinforced plastics. These types of polymeric materials have some common characteristics that make them attractive to aerospace system designers: light weight, corrosion resistance, and relative ease and low cost of processing and fabrication. Each type also has its own special characteristics that enable it to perform certain required functions better than other competing materials can (Table 1). The desirable properties of polymeric materials, which in some applications make them the only practical candidates, are partly offset by their principal limitation, which is degradation by exposure to high temperature. [ ]

Jan 1, 1971

By R. J. Beckman

This paper traces the history of mica mining in Alabama from 1870-1970. The decline of sheet mica production is noted and emphasis is placed on the more recent activity of scrap mica production and the development of the U. S. Gypsum Co. mica properties in Randolph County, Prospecting for weathered pegmatites of sufficient size to warrant development is a continuing challenge since most deposits are too small and all exhibit varying characteristics as to size, shape, and weathering. Quantity and quality of muscovite mica in the pegmatites is of utmost importance and its recovery during processing of the ore is described.

Jan 1, 1970

By Roland C. Walker

Traditional headed rebar has existed in the mining industry as a ground support product for many years. The head of a rebar bolt is most commonly produced by hot upset die forging. Upset die forging produces a rugged, simple head that performs well. Certain elements of the head must comply with regulatory standards, such as ASTM F432-95, which offers a standard test procedure to ensure quality of the product. The head style produced by all major manufacturers has been optimized to reduce manufacturing costs, provide greater miner safety and provide an excellent performing product. Observations were made in some mines of heads failing under in-situ loading. These observations could not be replicated according to the ASTM testing method. This paper highlights the problem and how a solution was developed. The development includes pictures of in-situ failures from the underground operations, laboratory replication tests indicating how this loading occurs, and then the use of this calibrated test method to validate the new design created.

Jan 1, 2009

By E. Escobar Pallares

Footnotes to column heads and explanation of symbols are given on page 239. H.C.T. means the deep zone for High Cold Test crude oil. L.C.T. means the shallow zone for Low Cold Test crude oil. They occur in the same area. In the same area there are many shallow pits and some wells. In the column showing total oil production to the end of 1939 are included 355,997 bbl. from shallow pits before 1939. During the last year there was no production from shallow pita.

Jan 1, 1940

By E. Escobar Pallares

Footnotes to column heads and explanation of symbols are given on page 239. H.C.T. means the deep zone for High Cold Test crude oil. L.C.T. means the shallow zone for Low Cold Test crude oil. They occur in the same area. In the same area there are many shallow pits and some wells. In the column showing total oil production to the end of 1939 are included 355,997 bbl. from shallow pits before 1939. During the last year there was no production from shallow pita.

Jan 1, 1940

By Frederic Becket

IN a recent article,1 which described the softening effect of columbium in plain high-chromium steels, the authors stated that their investi-gations had shown columbium to be also a particularly valuable inhibitor of intergranular corrosion in steels of the 18 per cent chromium, 8 per cent nickel type. It is the purpose of the present paper to record some of the results obtained through the introduction of columbium to the austenitic chromium-nickel steels. The damaging effects of this type of corrosion have become so widely known as to restrict considerably the applications of the steels under consideration, and therefore there is little question of the importance of the goal to be attained. Numerous contributions concerning the susceptibility of the aus-tenitic chromium-nickel steels to intergranular corrosion have appeared during the past few years, and among others who have dealt construc-tively with the subject are such well-known authors as Strauss and Houdremont of Germany, Hatfield of England, and Bain in the United States. Different theories have been propounded as to the cause of intergranular corrosion, and various remedial measures have been proposed, the majority of which involve the use of addition agents. Titanium is the addition agent at present most generally employed, as suggested by Houdremont and modified as described by Bain, Aborn and Rutherford.2 Little has been published on the effects of holding these steels for long periods at the relatively lower temperatures in the presence of

Jan 1, 1934

By J. A. Finch, B. J. Huls

Accurate level detection is required to make full use of level in optimizing control strategies for flotation columns. Techniques based on pressure and electrical conductivity are compared. Pressure and conductivity profiles give good agreement on level. Level calculated from single and multiple pressure values became more accurate using, in order, one, two and three sensor locations. The level estimate remained in error, however, because, unlike the collection zone, froth zone bulk density varies with height. A conductivity probe continually updating the conductance profile is a practical method of obtaining an accurate level.

Jan 1, 1990

By Thomas P. Mucho

To document the performance of mine roof and roof support systems the U.S. Bureau of Mines (IJSBM) has been installing instrumentation at selected sites in U.S. coal mines. Much of this support and roof instrumentation has been installed in high stress conditions to maximize differences in performance. Summarized in this paper are the results of four such site investigations. The roof geology at the four sites is quite different and is quantified using the USBM's Coal Mine &f Rating (CMRR). The studies included detailed measurements of roof movement using multi-point extensometers, as well as measurements and monitoring of bolt loading. The investigations include developmental loading and abutment loading from longwall and room-and-pillar mining operations. Some of the issues examined are the effect of the horizontal stress field, the effect of installed tension (torque-tension versus resin bolts), the effect of reduced annulus bolt holes, and the differences between similar bolts supplied by different manufacturers.

Jan 1, 1995

By Thor Skjeggedal

The Norwegian contracting firm A/S Høyer-Ellefsen has for the last 2.5 years carried out substantial pregrouting in a 7600m long tunnel just outside the city of Oslo. This has been done to avoid groundwater lowering and consequent damage to surface structures. A WIRTH TBM is used in combination with a 2 boom Atlas Copco hydraulic jumbo for the drilling of groutholes in front of the machine. The detailed procedure for the drilling and grouting will be discussed, and the results obtained will be presented.

Jan 1, 1981

One major aim of the operation of Aberfoyle's matte fuming pilot plant was to assess refractories performance in the process working vessel, a SIROSMELT furnace. High wear rates were expected and whether these could be tolerated was an important question. During operations a range of refractory types was evaluated in both insulated and water cooled furnace designs. Furnace operations enabled lining wear measurements to be made. Results confirm that existing technology can solve any expected refractory problems. Design aspects that should be included in commercial furnaces are shown.

Jan 1, 1984

By T. Y. Yan

O2, NaCl03, H202, NaOCI and Ce+4 have been examined as oxidants in an alkaline carbonate system for uranium in situ leaching. The South Texas and New Mexico ores contained up to 2.6 meq/g of reducing compounds that consume oxidants in the leaching operation. Leaching rates did not increase linearly with the oxidation potential of the oxidants. A mild oxidant can be used to maximize uranium oxidation selectivity and oxidant efficiency. 02 can oxidize most of the uranium mineral with an adequate rate and high oxidant efficiency.

Jan 1, 1993