Search Documents

By H. J. McQueen, G. C. Kuczynski

ThE useful properties of k6-Alfenol and the thermenol alloys (summarized by J. E. Nachman and W. J. Buehler') have encouraged research into those alloys which, having compositions near 25 at. pct Al, 75 at. pct Fe, undergo an ordering transformation between 500° and 550°C. The equilibrium diagram of the iron-rich iron-aluminum alloys was first determined by Bradley and Jay.2,3 They distinguished three structures: the disordered, which is bcc; FeAl, which is simple cubic with one Fe atom and one Al atom per lattice site; and Fe3Al, which is fcc with three Fe atoms and one Al atom per lattice site. This last structure may be conceived as eight body-centered cubes with Al atoms at the centers of alternate ones, so that Al atoms have only Fe as first and second nearest neighbors. Later, Osawa and Murata4 determined the boundaries of the different superlattice regions in the iron-rich Fe-Al solid solution by dilatometric and X-ray methods. Two of the six phases, which they found between 0 and 50 at. pct Al, were never identified by other workers. A. Taylor and R. M. ones,' concurrently with and independently of this research, redetermined this diagram by measuring lattice parameters at temperature. Further reference will be made to their results. EQUILIBRIUM DIAGRAM A) Experimental Procedure—The alloys were prepared from NRC gas-free iron (99.9 pct Fe) and 99.99 pct Al. They were melted in alumina' crucubles under vacuum in an induction furnace. If the ingots were unsound or showed more than a 3 pct weight loss, they were rejected. The ingots were homogenized at 1100°C for 24 hr before hot-rolling at 700" to 900°C from 1 in. to 0.25 in. thick. It is interesting to note that alloys containing more than 28 at. pct Al were able to take an 80 pct reduction of area in the ordered FeAl region. The dilatometer specimens and specimens for chemical analysis were cut from these plates. A Leitz dilatometer was used to measure the coefficient of linear expansion as a function of temperature. The specimens were slowly cooled from 900" to 300°C where they were annealed for 10 hr before slowly cooling to room temperature. The expansion was recorded photographically as the alloys were heated and cooled at 1.5oC per min between 100" and 1000°C. The magnetic measurements determining the Curie points were performed on the dilatometer specimens in the dilatometer, by using direct current in the furnace windings both to heat the specimen at 1.5°C per min and to serve as the primary coil. The regular specimen holder was replaced by a thin alundum tube on which was wound, as a secondary, a closely spaced coil of fine copper wire. A reversal of current in the furnace windings produced, in the secondary, an emf which was proportional to the induction in the specimen, and which could be detected on a galvanometer. In this way, it was possible to determine the Curie points of alloys to within * 5°C. B) Results and Discussion—The coefficients of linear expansion, as obtained from the dilatometer curves, are plotted as a function of temperature and composition in Fig. 1. Since in many cases the heating and cooling curves were superimposed, it was decided to measure slopes of heating curves only. Definite high peaks, due to the transformations, were observed on each curve between 400" and 520°C, and, for alloys containing more than 23 at. pct Al, a second set of smaller peaks at temperatures above 660°C. The sharpness of the peaks indicates that ordering to Fe3Al is a first-order reaction. The compositions and the temperatures of these peaks are listed in Table I. When these temperatures are plotted as a function of the composition, the result is the constitution diagram presented in

Jan 1, 1960

By Eugene F. Broome, Hugh A. Walls

Self-diffusion coefficients were measured using the modified shear cell technique over a temperature range from 31" to 401°C. These data agree within experimental error with those of Petit and Nachtrieb, which were determined from 30°to 99°C. LIQUID self-diffusion behavior in gallium has been studied previously by Petit and Nachtrieb&apos; using their shear cell technique.&apos; Data were obtained in that investigation over temperatures ranging from 30.6 to 98.7"C, and these comprise the only published data for liquid gallium. In the work reported here, diffusion data were obtained from 30.8 to 400-9.Cusing a shear cell technique different from that of Petit and Nachtrieb. This modified shear cell method and the mathematical analysis for diffusion in a finite capillary geometry have been previously described.3 PROCEDURES AND ANALYSIS The segments of the modified shear cell were fabricated from types 304 and 316 stainless steel. No corrosion problems with gallium were encountered until attempts were made to obtain data at 500°C. The diffusion capillary diameter was 1.59 mm and capillary lengths for the four sets of cell segments used are given in Table I. Gallium with a purity of 99.999 wt pct was obtained from Var-Lac-Oid Chemical Co. The gallium-72 isotope used to measure the self-diffusion coefficients was produced from this inert gallium by irradiation in The University of Texas Reactor Facility, and was checked for radiochemical purity. Following a period of isothermal diffusion controlled to within 0.0l°C, the contents of each capillary section were emptied into a counting planchet, weighed to assure that gallium had not been lost during handling, and the radioactivity determined by windowless gas-flow proportional counting. Great care was taken to obtain a reproducible counting geometry for the samples. Diffusion coefficients were obtained from the solu-tion3 to the diffusion equation for the modified shear cell problem, viz.: in which B2= C2(t)Li + L2)- CSL1-COL2 P* (C0-Cs)(L1+ L2) and L, and L2 are the capillary segment lengths. The step-function initial concentration distribution was expressed as C(x,O) = C, for -L1 = x < 0 and C(x,O) = Co for 0 < x 5 L?. Also, C2(0 = ^- fcix,t)dx Computation of the diffusion coefficients was done numerically as described in our earlier paper.3 Because of the short half-life of gallium-72 (14.1 hr) and the relatively long counting times taken to give a precise value of the diffusion coefficient, it was necessary to account for the radioactive decay both during the actual count and between counts for different samples (before and after diffusion). Thus, the average count rate Cz(t) for a second sample counted from times t3 to t4 can be made consistent with the average rate Co determined for a first sample counted from times t1 to t2 by the relationship: N(e-»i-e-M») , , C2(f) " &-«,)(*-«.-«-»«) [21 in which N is the total number of counts taken and is the decay constant. RESULTS AND DISCUSSION The self-diffusion coefficients determined in this investigation are listed in Table 11. Values of the parameters used to calculate the coefficients are given in the table, as are values of the random counting error &apos; for the concentration ratio pz and the corresponding expected random variation AD in the diffusion coefficient. The quantity is calculable from: &apos;Cg — C2(t)} , „ ,2 .-„¦, M co-csl(ACs)J W in which AC is the error in the individual count rate. The mean values of the diffusion coefficients within each temperature group are also given in Table 11. Such temperature groupings of data are reasonable because of the small variations between the temperature~.~

Jan 1, 1970

By R. E. Goodman, M. A. Mahtab

The, state of stress around a vertical wellbore in rock following nonlinear stress-strain laws is examined by means of finite element analysis. The wellbore, is considered an axisymmetrier body with axisymmetric loading. The initial vertcal and borizontal stresses are "locked" in the rock elements around the wellbore and a new state of stress is generated by the displacements which occur around the borehole. A point-uise variation of the elastic moduli is made on the basis of the new stress state and the triaxial data. The initial stresses tire now reintroduced along with tile changed moduli and original boundary constraints. This procedure is repeatrd until convergent stresses are reached. The effect of nonlinearity on streases is examined for a 6,000-ft wellbore in a scbistose gnezss and Berea sandstone using results of laborratory triaxial compression tests. The results sbou that the effect is restrited to one well radius from the bottom periphery of the bole. Beyond a distance of one-quarter radius, the elfect of nonlinearity on stresscs IS almost always less than percent for the cases conszdered, The consideration of a static pressure inside the well does not magnify the effect of monlinearity on borehole stresscs. INTRODUCTION The terms " wellbore" and "borehole" here designate cylindrical openings in the ground with vertical axis and a circular cross-section. A knowledge of the stress redistribution that occurs on excavating a wellbore is important in understanding (1) the behavior of the lined or unlined hole, (2) hydraulic fracture response, and (3) the effect of stress redistribution on drillability; also it is important in predicting initial stresses in the virgin ground, and in analyzing the response of measuring instruments placed in the borehole. Our knowledge of the state of stress around a wellbore has been restricted to homogeneous, isotropic, elastic material and derives chiefly from the analysis by Miles and Toppingl and the photoelastic work of Galle and Wilhoit2 and Word and Wilhoit.3 In this investigation the state of stress is examined for a nonlinear elastic material by means of finite element analysis. Many rocks possess stress-strain curves that depart notably from straight lines in their initial or final portions. While the literature contains abundant stress-strain data from triaxial tests (axisymmetric loading) on cylindrical rock specimens, there is little information on rock deformability under nonaxisymmetric loading conditions such as occur at each point around the bottom of a wellbore. Although there is some knowledge of the effect of intermediate principal stress on rock strength, there is virtually nothing known about its effect on rock deformability; therefore, we have assumed here that the effect of intermediate principal stress can be ignored. A schistose gneiss4 and Berea sandstone5 were selected as representative rocks for this analysis. The traditional graphs of deviator stress (ol -o3) vs axial strain were reworked to give the tangent modulus as a function of the deviator stress for varying values of the minor principal stress. The result is a nesting family of skewed, bell-shaped curves for tile gneiss (Fig. 1A) and the sandstone (Fig. 2A). A similar replotting of the lateral strain data defines the variation of Poisson&apos;s ratio (v) with the deviator stress and confining pressure. These curves, shown in Fig. 1B for the gneiss and in Fig. 2B for the sandstone, are not so well ordered as the tangent modulus curves. However, all of these display an increase of v with deviator stress application, but the rate of increase diminishes with confinement. The ET and v curves for the two rock types are tabulated in Tables 1A and 1A for use in a digital computer so that material properties corresponding to a given state of stress can be assigned by interpolation. STATEMENT OF THE PROBLEM Given a state of stress in the ground prior to drilling a hole (initial stresses), we assume that

Jan 1, 1969

By John Armstrong, Michael Savill, David Powell

Hong Kong is an intensively developed region and has the highest vehicle densities in the world. In 2000 there were 6.6 million people and 580,000 vehicles using 1,890 km of road covering the 1084 km 2 territory. The high vehicle and population densities together with the difficult terrain have seen road tunnels emerge as key components both in the current and future road transportation network. Currently there are eleven operating highway tunnels in Hong Kong, seven government owned and the remaining four “build, operate and transfer” franchises, see Figure 1. The very first tunnel was the dual two Lions Rock Tunnel completed in 1967and the latest the dual 3 lane Tai Lam Tunnel opened in mid 1998. Figure 2 shows the alignment and statistics for all 11 Hong Kong tunnels. Looking ahead, Hong Kong has embarked on the study and design of the next generation of major highways and as many as a further seven tunnels are currently under feasibility study or detailed design. This seems an opportune year to produce a broad appreciation of the fire strategy, life safety and ventilation practices in Hong Kong not only for the existing tunnels but the new standards and requirements for the next generation of Hong Kong tunnels. This paper provides an overview of the fire strategy, life safety and ventilation of Hong Kong’s existing and planned tunnels. The paper pays particular attention to the areas where the unique conditions and requirements in Hong Kong impacts on tunnel and systems design and the solutions adopted to overcome these challenges.

Jan 1, 2001

By Ulf S. Landergren

Diffusion coefficients and marker movements have been determined in brass using welded couples. Three different concentration ranges were employed at 750°C, while a fourth concentration range was measured at 500°, 600°, 700°, and 800°C. Marker displacements toward and porosity development in the high zinc side of the couple were observed in all cases. The results were interpreted as favoring a vacancy diffusion mechanism. IN the large amount of diffusion literature which has accumulated during the past half century, very few experimental data have been presented on body-centered-cubic metallic phases. The impressive combination of experimental and theoretical studies which has given the vacancy mechanism a fairly secure position as the preferred mechanism for most face-centered-cubic metals has no counterpart for body-centered-cubic phases, although the theoretical picture seems to be in a better state than the experimental work. The attempts to select diffusion mechanisms by the theoretical calculation of the activation energy for the various conceivable unit diffusion processes and the energy of formation of the type of lattice defect required have been based on models of two kinds. The first kind utilizes potential functions fitted for certain properties of pure crystalline copper; the second kind is fitted for sodium. The latter is an example of an open metal in which the metallic ion is small compared with interatomic distance,&apos; while the former is characteristic of the larger class of metals in which the ions have diameters about as large as the interatomic distance. brass should resemble copper in this fundamental property. It should be evident that results on the mechanism of diffusion obtained for one of these classes need not necessarily apply to the other. Huntington and Seitz, using a model of the copper type, showed that the activation energies to be expected for interstitial migration or a two-atom direct interchange were much higher than that for vacancy diffusion. Zener pointed out that a four-atom ring rotation would involve an activation energy considerably lower than the two unlikely mechanisms although still higher than the vacancy mechanism in the face-centered-cubic structure. Furthermore, he argued, the four-atom rotation would be relatively easier in a body-centered-cubic lattice and might be competitive with the vacancy mechanism. Paneth showed that a body-centered-cubic crystal-like sodium could form interstitial defects of special type, called a crowdion, by crowding an extra atom into < 111 > directions where the defects would affect a line of about eight atoms. The defect was constrained to move along the defining line. Unlike the face-centered-cubic case, therefore, the theoretical calculations for the body-centered-cubic mechanism do not provide a very clear-cut answer, and the absence of adequate experimental studies is the more serious. This investigation was undertaken for the purpose of obtaining useful information on diffusion in body-centered-cubic phases. brass was chosen for several reasons: 1—the phase field is sufficiently wide at high temperatures to permit the use of diffusion couples with adequate concentration ranges for satisfactory chemical analysis, 2-—thermodynamic activity data are available for the calculation of mobilities from diffusion coefficients, 3—the phase is as close to the theoretical model of the copper -type on which the calculations have been done as any body-centered-cubic metallic phase is likely to be. Measurements of the movements (if found) of inert markers during the diffusion process would indicate that a vacancy or Or mechanism played a major role in diffusion in brass. If no marker movement should be found, a ring mechanism would be indicated but not assured. Experimental Procedure The alloys used in these experiments, listed in Table I with analyses, were supplied by the Naval Research Laboratory. They were from ingots of 3x3 in. cross-section, heated to 760°C, reduced under a

Jan 1, 1957

By P. Greenfield, P. A. Beck

RECENT work by J. Darby, Jr. in this laboratory has shown that the reported vanadium-rich limit of the s phase in the Co-V system at 1200°C is in error. The appearance of a second phase in s actually is restricted to alloys containing over 68 atomic pct V. The error in the original value is due apparently to a reaction that takes place along the numerous cracks in the s specimens between the alloy and the impurities present in the He + 8 pct H atmosphere in the annealing furnace. Such a reaction and the consequent appearance of a second phase can be suppressed if the alloys are sealed under vacuum in Vycor tubing. The new value of 68 atomic pct V for the vana-dium-rich limit of the s phase in the Co-V system effects slightly the s compositions calculated from average values of N, and N,. for various s phases. The standard deviation between experimental mean compositions and those calculated from the assumption that s is characterized by a constant number of 3d + 4s electrons per atom (N,), is slightly reduced from 9.1 to 8.8 pct. The maximum divergence for the V-Mn s phase is reduced from 15.5 to 14 atomic pct. The standard deviation calculated from constant electron vacancy numbers given by N.. = 4.66 (Mo + Cr + V) + 3.2 (Mn) + 2.2(Fe) + 1.71(Co) + 1.6(Ni) is now greatly reduced, as the maximum divergence for this correlation previously occurred in the V-Co system. This maximum divergence is reduced from 7.6 to 2.3 pct, and the standard deviation for all s- phases is reduced from 4.1 to only 2.9 pct. The correlation for electron vacancy numbers given by N. 5.66 (V when with Ni or Co) + 4.88 (V when with Mn or Fe) + 4.66 (Cr + Mn) + 3.3 (Mn) + 2.66 (Fe) + 1.71 (Co) + 0.61 (Ni) is made slightly worse, and the standard deviation increases from 2.8 to 3.9 pct. These changes, however, do not affect the conclusions of the paper.&apos; The deviation between calculated and experimental s compositions is much less for either one of the electron vacancy correlations than for the correlation with the number of 3d + 4s electrons.

Jan 1, 1955

By F. S. Buffington, Morris Cohen

THERE is little quantitative information available concerning the effect of applied stress, in both the elastic and plastic ranges, on diffusion kinetics. Accordingly, a program has been undertaken to determine the rate of self-diffusion in high purity iron, with the specimens subjected to stress during the course of diffusion. Results are reported here for body-centered cubic iron at a diffusion temperature of 890°C. The iron used was 99.97 pct Fe, the principal impurities being 0.002 pct C, 0.008 pct 0, and 0.02 pct Si. The surface-decrease method of self-diffusion analysis was employed, and Fe55 Mn x-radiation, 2.9 years half-life) was the tracer element. Details of specimen preparation and equipment are given elsewhere.&apos; Disks of the high purity iron, % in. diam x 1/4 in. thick, were annealed at 890°C for 18 hr in dry hydrogen to produce large grains of a ferrite. The faces of the disks were then surface ground, and possible grinding stresses were relieved by annealing at 890 °C for 45 min in vacuum. A layer of radioactive iron 0.00186 cm thick was electroplated on one face of each disk. The self-diffusion coefficient was calculated from the ratio of the radiation intensities emanating from each of these faces, as measured before and after diffusion.&apos; The heating was carried out in a vacuum furnace (10-5 mm Hg) controlled to ±1.5°C. The specimens were loaded in compression between two quartz disks during the diffusion runs by means of a lever system operating through a vacuum seal. Thus one quartz disk was pressed directly against the radioactive face of the specimen, minimizing the vapor loss of radioactive iron. Steady-state creep occurred in all instances where permanent deformation could be detected, but the specimens did not exhibit appreciable transverse barreling until natural strains of 0.2 to 0.3 were attained. Essentially, the diffusion took place under uniaxial stress. The plastic strain in each case was obtained at the diffusion zone by measuring the diameter d there before and after the run: e = 2 In — do Let Du equal the self-diffusion coefficient which would have prevailed at the given temperature if no stress had been applied. This was calculated from the temperature-dependence equation which had been previously determined: —59,800 D, = 6.2 exp ( I sq cm per sec* [I]

Jan 1, 1953

By Derham DW, Newcombe LA

The operations of the Mount Morgan gold tailings retreatment plant were significantly improved in 1984 by the desliming of the CIP plant feed, which reduced cyanide consumption and increased percent gold dissolution. Subsequently, the development of slimes treatment, incorporating gold leaching from slimes solids by copper cyanide complexes in the process water, and gold adsorption on to carbon in an environment lacking free cyanide was successfully implemented. Mount Morgan was initially mined for gold commencing in 1882 on the auriferous ironstone cap to the sulphide ore body. During the history of mining and processing at Mount Morgan the operations have developed through numerous phases of gold and copper production, operating almost continuously through until the final closure in late 1990. The final phase of processing was the retreatment of tailings, predominantly flotation tailings accumulated since the 1930s, for the recovery of gold and minor silver. Tailings retreatment commenced in 1982 with the commissioning of a 10 000 tonnes per day CIP plant to treat some 40 million tonnes of tailings at an average grade of 1.08 g/t Au. The initial operations were hampered by high cyanide consumption and poor gold dissolution on the mixed siliceous/pyritic tailings. The successful development and implementation of the desliming of the CIP plant feed in 1984 (as described by Parsons and Hampshire, 1986) reduced cyanide consumption by 40 per cent, and raised gold extraction by 13 per cent points by virtue of significantly higher dissolved oxygen levels. The finer portion of the reclaimed tailings were deslimed by eighty 100 mm diameter AKW cyclones, with the desliming cyclone overflow thickened in a Warman 30 in diameter thickener for water recovery and slimes disposal. Operation of the desliming plant involved the discarding of a slime fraction representing about 15 per cent of the reclaimed feed. Although gold-bearing, the high content of cyanicides and oxygen consumers within the slime negated any conventional treatment of this stream with free cyanide for gold recovery. The natural lixiviant behaviour of the soluble copper cyanide complexes for gold, which was extremely evident at Mount Morgan, directed efforts in this area. Enhancement of gold leaching with a deficiency or near absence of detectable free cyanide, but with significant levels of copper cyanide complex from recycled process water were examined. Adsorption of this solubilised gold onto carbon in a similarly difficult environment required close examination.

Jan 1, 1993

By Noel Cunningham

Many excellent descriptions of the mills of the Porcupine district have been written, but no discussion exclusively devoted to the metallurgical technology has been given. These notes are intended to cover this feature briefly. They are based upon 21/2 years&apos; mill operation in the district—i.e., practically since the beginning of metallurgical operations. Character of the Porcupine Ore.—There is no oxidized ore in the district, the surface having been deeply planed by glacial action in recent geologic time. The precious-metal content is about in the proportion of 85 of gold to 15 of silver by weight; hence, the silver is practically negligible. There are two classes of Porcupine ore, having very different characteristics; these will be referred to throughout this paper as Class A and Class B. Class A ore is a pure quartz with inclusions of schist. Generally it is heavily fractured and breaks down readily to sharp, hard grains, about minus 10 plus 20 mesh, requiring further comminution to release the gold. It carries very little pyrite; the gold is entirely free and apt to be coarse, but often spongy, going into solution readily on that account. This gold is 60 per cent. to 85 per cent. free milling, depending on the grade of ore. Class B ore is an iron silicate schist, strongly laminated, carrying 4 to 5 per cent. pyrite; its specific gravity is 2.8 to 3.0, depending upon the amount of mineralization. In breaking the ore in the mine, generally over 25 per cent. of material through a 1/2-in. ring is made; the ore readily breaks down in milling and makes a comparatively large amount of non-crystalline slime; owing to its high specific gravity, however, it is quick settling. In my opinion, the gold in this ore is free, but so finely divided that it will neither pan nor amalgamate; it appears to be disseminated through the rock and not chiefly associated with the pyrite. Veins of Class A ore occur with or without side walls of Class B, and veins of Class B occur unassociated with Class A; more often the veins are closely banded, Class A and Class B alternating, generally with Class B in excess. Both classes of ore are more or less blocky at times, and with reference to Class B this is indicative of low gold content.

Jan 1, 1915

By T. N. McVay, E. E. Creitz

INTRODUCTION Object RATHER large amounts of titanium minerals and some zircon and monazite are being recovered from dune sands about 10 miles west of Jacksonville Beach, Fla. The Mining Branch of the Bureau of Mines, Southern Experiment Station, has been interested in developing additional large deposits of similar sands in other areas of Florida. The results of a field study have been published1 concerning the sands occurring on Trail Ridge which runs north and south about 30 miles southwest of Jacksonville. This investigation was undertaken in order to identify the opaque titanium minerals occurring in Trail Ridge and because of the economic importance of Florida titanium minerals. Nature of the Problem The minerals present in the heavy fractions (sp gr > 2.94) of the sands are principally opaque minerals; staurolite, zircon, sillimanite, tourmaline, kyanite, rutile, a small amount of corundum, traces of the zinc spinel gahnite and garnet. Epidote, monazite, hornblende and titanite are present in other dune sands but these minerals were not noted in the samples collected on Trail Ridge. All of the minerals except those which are opaque can be readily identified by the usual petrographic methods. However, opaque minerals cannot be examined satisfactorily by transmitted light. Polished sections of the opaque-mineral grains were examined but these sections did not furnish useful information. Consequently, it was necessary to use means other than the usual petrographic methods to identify them. Previous Investigations of Heavy Minerals in Florida Sands Martens2 has described the heavy minerals in the Florida beach sands and has classified the opaque minerals as ilmenite with minor amounts of leucoxene. Miller3 studied a number of sands collected by Ross and Mertie in Florida. He states that the material from the Florida beach and dune sands that commonly has been called ilmenite has essentially the chemical composition of the material that has been called arizonite.4 The X ray diffraction patterns of several samples indicated that the supposed ilmenite is essentially amorphous, with only weak lines corresponding to ilmenite, and hence the material is unlike the type of arizonite from Arizona. Opaque Titanium Minerals Rutile is essentially titanium dioxide. However, as pointed out by Dana,5 important amounts of Fee and Fe3 as well as Cb and Ta are reported in some analyses.

Jan 1, 1947

By Paul Billingsley, Augustus Locke

Certain adequately developed mining districts give complete three-dimensional patterns of ore bodies as clusters rising from roots in basement rocks with details controlled by structure of cover rocks. Examples are Goodsprings, Tintic, Bisbee, Leadville, Hedley, Eureka, Ely and Goldfield. In these and others the controlling structures in both basement and cover rock are elements of the neighboring regional structure and have been produced by rock movements in harmony with continental adjustments, which are usually steep tear faults in basement and thrust crumples in cover. Invariably the structures and movements in the districts have long geologic history and result from intersecting or superimposed deformations of different ages. Salt Lake districts show intersecting Uinta and Cordilleran elements; Colorado districts show intersecting pre-Cambrian and Tertiary elements, and Bisbee shows Tertiary superimposed on fina1 Paleozoic folding. Thus the position of districts has been determined by the patterns of North American orogenic belts, which make crossroads in Rocky Mountains and blocks of superimposed deformation in Sierra Nevada, northwest Coastand Canadian Coast Ranges. Essential function of repeated deformation is to strengthen rock, as from shale to slate to schist to gneiss, and thus make it competent to carry channels to depth with or without addition of intrusives. The essence of a mining district is the presence of such competent rocks with long-lived, deep, penetrating breaks reopened to permit passage of heat and associated products from depths to surface. It is suggested that melts such as magmas; metamorphism up to and including granitization; alteration, such as orthoclase-quartz or quartz-sericite or garnet, and also mineralization, may all be by-products of such heat escape along channels made by tectonic forces at specific foci. Magnitudes of Districts (Fig. 1) Any synthesis of ore deposits must deal with comparable units. Ore deposits are innumerable, but great ore deposits, commercially important for a generation or more, are few. The bulk of metals has come from districts of the first and second magnitudes (over $1,000,000,000 and over $250,000,000, respectively), and of these the United States and adjacent provinces of Canada and Mexico contain only 28, of which 9 are first magnitude: Butte, Coeur d&apos;Alene, Bingham, Bisbee, Sierra Gold, in the West; Tri-State, Southeast Missouri, Michigan copper, Sud-bury, in the East. Another 28 or 30 districts are of third magnitude (over $50,000,000).

Jan 1, 1941

By Augustus Locke, Paul Billingsley

Certain adequately developed mining districts give complete three-dimensional patterns of ore bodies as clusters rising from roots in basement rocks with details controlled by structure of cover rocks. Examples are Goodsprings, Tintic, Bisbee, Leadville, Hedley, Eureka, Ely and Goldfield. In these and others the controlling structures in both basement and cover rock are elements of the neighboring regional structure and have been produced by rock movements in harmony with continental adjustments, which are usually steep tear faults in basement and thrust crumples in cover. Invariably the structures and movements in the districts have long geologic history and result from intersecting or superimposed deformations of different ages. Salt Lake districts show intersecting Uinta and Cordilleran elements; Colorado districts show intersecting pre-Cambrian and Tertiary elements, and Bisbee shows Tertiary superimposed on fina1 Paleozoic folding. Thus the position of districts has been determined by the patterns of North American orogenic belts, which make crossroads in Rocky Mountains and blocks of superimposed deformation in Sierra Nevada, northwest Coastand Canadian Coast Ranges. Essential function of repeated deformation is to strengthen rock, as from shale to slate to schist to gneiss, and thus make it competent to carry channels to depth with or without addition of intrusives. The essence of a mining district is the presence of such competent rocks with long-lived, deep, penetrating breaks reopened to permit passage of heat and associated products from depths to surface. It is suggested that melts such as magmas; metamorphism up to and including granitization; alteration, such as orthoclase-quartz or quartz-sericite or garnet, and also mineralization, may all be by-products of such heat escape along channels made by tectonic forces at specific foci. Magnitudes of Districts (Fig. 1) Any synthesis of ore deposits must deal with comparable units. Ore deposits are innumerable, but great ore deposits, commercially important for a generation or more, are few. The bulk of metals has come from districts of the first and second magnitudes (over $1,000,000,000 and over $250,000,000, respectively), and of these the United States and adjacent provinces of Canada and Mexico contain only 28, of which 9 are first magnitude: Butte, Coeur d&apos;Alene, Bingham, Bisbee, Sierra Gold, in the West; Tri-State, Southeast Missouri, Michigan copper, Sud-bury, in the East. Another 28 or 30 districts are of third magnitude (over $50,000,000).

Jan 1, 1941

By D. Pienaar, B. McFadzean, T. Jordaan

"Dithiophosphate (DTP) collectors have the lowest affinity for sulfide mineral surfaces compared to other common sulfide mineral collectors, such as xanthates and dithiocarbamates. In some cases it has been found that DTP does not adsorb onto the mineral surface at all and yet increases in recoveries and grades are noticed with the addition of DTP. Many studies have investigated the interactive effects of collector mixtures. However, there have been relatively few studies on the interactive effects between frother molecules and collectors. This study investigates the interactions between different types of frothers and sodium diethyl dithiophosphate.The study found that there were large increases in pyrite and galena microflotation recoveries at both pH4 and pH9 when DTP was mixed with small amounts of frother at a constant bubble size, showing that these increases were neither mineral-specific nor pH-specific. The same effect was not present when xanthate was used as a collector. The increases in recovery when using the DTP-frother mixture were similar irrespective of the type of alcohol or polypropylene glycol frother that was used. In an attempt to distinguish the mechanism of enhanced flotation recovery, various supplementary experiments were performed. It was found through adsorption experiments that no DTP was adsorbing on to the mineral surface. Therefore, interactions at the air-water interface were performed. Surface tension and critical coalescence concentration tests showed that, while DTP is a weak surfactant at the air-water interface, it does not have a synergistic effect in the presence of frother. DTP-frother mixtures do, however, show interactions in the froth phase, indicating an interaction in the thin films. It is proposed that there is a DTP-frother interaction on the bubble surface that enhances the rate of film thinning at the 3-phase bubble-particle contact."

Jan 1, 2018

By E. Bicknese, R. Clark

The mechanism and rate of reduction of FeO at conditions similar to those in the stack of a blast furnace have been determined for temperatures from 980" to 1165°C. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal in a static system (no flow of reducing gas) have shown that the CO2-CO ratio of the product gas depends upon the relative reactivities of the Fe2O3 and charcoal. In a systern with a "hot blast" of CO and Nz (simitar to dry bosh gas), synthetic FeO, and actiuated coconut charcoal, the rate of reduction was not sensitive to the flow of reducing gas, and the rate-controlling step alas the chemical reaction at the metal-oxide interface. Wherz solid carbon was not present, a critical flow rate of reducing- gas had to be met in order to prevent a lowering of the reduction rate. The effect of a less-reactive carbon (blast-jurnace coke) and of a "natural" FeO on the mechanistn and rate, and the mininum amount of carbon necessary in the charge to tnaintain the reducing potential of the gas phase, have been determined. THE importance of iron oxide reduction processes has encouraged many studies of the process reaction kinetics. Despite this, the mechanism is not well-understood and three main theories have evolved, which can be stated as follows: A) the rate-controlling step is diffusion, either gaseous diffusion of the reductant or product gas through a porous solid,&apos; or solid-state diffusion of iron and oxygen atoms through the so1id.2 B) The slow step is diffusion of reducing gas through a stagnant boundary layer. C) The reaction rate is controlled by the chemical reaction occurring at the metal-oxide interface and is proportional to the area of this interface.3 By increasing the velocity of the reducing gas to a flow rate beyond which no increase in the reduction rate is observed, critical flow rate, it may be possible to eliminate B as the slow step. However, as warnere points out, the establishment of a critical flow rate may only assure that the reaction is not limited by a reduction in the reducing potential of the gas and that B may still be the rate-determining step. Edstrom and Bitsianes and Seth and Ross8 show that A and C may both be correct for the reduction of the same oxide, depending upon the stage of the reduction, and that the relative importance of the two mechanisms varies with the porosity of the oxide. Themelis9 has derived expressions which express A, B, and C in terms of the fraction reduction, Rx, of a spherical particle. Thus, in the case of A a plot of In (1 - Rx) vs time must be linear and the time to reach a given reduction is proportional to the square of the particle diameter. For B a plot of (1 - Rx) vs must be linear and the time to reach a given reduction is proportional to the square of the diameter. For C a plot of 1 - (1 - RX)1/3 vs f must be linear and the time to reach a given degree of reduction should be proportional to the diameter. In the case of mixad controlled reactions, none of the plots are linear over their entire length. The results of previous studies, in which the rates of gaseous reduction of iron oxide were measured in the absence of carbon, may not correspond to blastfurnace practice because they ignore the effects of the Boudouard reaction. CO2 +C — 2CO The presence of carbon may alter the mechanism or the rate of iron oxide reduction through an enrichment of the gas phase by Eq. [1]. In this case, the presence of and reactivity of carbon become important. If the Boudouard reaction has no effect on the rate of reduction, the reducing gas could be supplied by some means other than the gasification of carbon at the tuyeres and carbon could, theoretically, be eliminated from the burden. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal were made to determine if the reactivity (surface area) of the Fe2O3 had any effect on the product gas composition. Two size fractions of Fe2O3 were reduced with charcoal in a static system (no flow of reducing gas). In each case the charcoal was -100 + 325 mesh and was 25 pct of the total charge. One fraction of the reagent-grade Fe2O3 was submicron in diameter. The other fraction was -100 + 200 mesh and was prepared from the former by compacting, sintering at 1300°C, crushing, and screening. In each experiment, the reaction vessel was filled with a mixture of CO and CO, which would be in equilibrium with FeO and iron at the reaction temperature. A furnace was heated to the desired temperature, the vessel was placed in the furnace, and the gaseous products of the reaction were collected and analyzed. The results of these experiments, Fig. 1, show that the gas phase associated with the submicron oxide is more oxidizing than that with the -100 + 200 mesh oxide. Therefore, in a static system, the relative rates of the reduction reaction and the gasification of carbon depend upon the reactivities of the Fe2O3 and charcoal. The reduction of FeO to iron is the most important reaction occurring in the blast furnace and is probably the slowest of the several reduction steps. The mechanism and rate of reduction of FeO in a system containing carbon and a flow of dry bosh gas have been studied. TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AlME

Jan 1, 1967

By H. D. Yu

In this paper, an evaluation about the process mineralogy of the rich iron mine in Mongolia with comprehensive methods is given; this provides foundation of the comprehensive recovery of iron and cobalt in the ore. The research shows that the iron?s grade is 61.23%, Co?s grade is 0.02%, the ore is rich iron ore and its Co content also reaches border mining grade. For the ore, if want get high grade iron concentrate powder, must identify the mineral composition and the occurrence of iron and take into ac-count the recovery of Co content as associated resources. Chemical phase analysis results show that 86.35% of iron exists in magnetite, which means that the theoretical recovery ratio of iron is close to 86%. Minerals spectrum analysis confirmed that the magnetite containing a small amount of Mg, Al, and other impurities, the actual iron minerals to 70.28%, which means that theoretically iron grade iron concentrate only close to 70.28%. Based on the result of iron chemical phase analysis, by investigating the liberation of sulfide minerals and gangue, the recovery index of iron can be forecasted, when grinding fineness is 35%, 45%, 55% and 65% bellow 0.074mm,theoretical content of Fe in iron concentrate separately is 67.71%,67.88%,68.78%,and 69.43%,accordingly the theoretical recovery of Fe is 87.38%,87.05%,86.92% and 86.63%. From the perspective of process mineralogy, the forecast mineral beneficiation indicators show that the ore is easy sorting ore, iron processing operations have higher recovery rate, but wants sorting of high-grade iron ore concentrate still need appropriate grinding fineness. Furthermore, associated element Co, existing mostly in pyrite and pyrrhotite, is valuable in the ore. Pyrite and pyrrhotite have ideal liberation under grinding, so cobalt can be easily enriched in sulfide concentrate.

Jan 1, 2014

By M. S. Diederichs, J. Oke

Surface limitations and a need for more direct transportation routes require serious consideration be given to the development of underground construction works in geotechnically unfavourable conditions. Due to geographical and logistical limitations, the construction of these underground works is restricted to difficult ground conditions that require temporary pre-support before excavation in order to avoid tunnel collapse or severe surface settlement. One type of pre-support is the umbrella arch system, which has been gaining popularity due to cost and time commitment in comparison with other pre-support systems (e.g., ground freezing). The umbrella arch system has been employed with significant frequency around the world, yet without a complete understanding about the mechanical response of the system. As such, literature has found the temporary support system to be both under and over designed with regard to safety and/or economical impact. The authors of this paper have made three major contributions to increase understanding of the umbrella arch system and to help optimize the design process. Firstly, the authors have developed nomenclature in order to categorize and define umbrella arch elements and systems, which also stimulated the creation of the empirically driven Umbrella Arch Selection Chart. Secondly, the authors have established a design methodology that is primarily based on advanced numerical modelling techniques to aid in the optimized design of the umbrella arch arrangement for site specific conditions. Thirdly, the authors have developed a semi-analytical model for umbrella arch systems employed in squeezing ground conditions by incorporating elastic foundation theory as well as convergence confinement theory. These three major contributions to such a widely employed tunnelling pre-support system will be introduced and explained in detail, and will include discussion of how each is incorporated in the complete tunnel support design process and throughout the construction and monitoring phase of a project.

Jan 1, 2015

By Howard N. Eavenson

ALL of the matters so far taken up by the Institute Committee on Stabilization of the Coal Industry will be of help, but it seems to be that under present conditions not very much can be expected until the railroad situation has been improved. As an instance of this, I would cite the fact of our experience at our mines in West Virginia and Kentucky. During 1917 and 1918 at our West Virginia plants we produced for our own consumption, practically entirely in the Chicago district, about 4,750,000 net tons of coal. In 1919 our output was reduced to 3,500,000 tons, this being caused partly by the shortage of orders in the few months following the armistice, but more particularly by The car shortage which began last September and continued throughout the remainder of the year, with the exception of December. This car shortage has been more acute since the first of the year, and while we now have an actual capacity here of 20,000 tons daily and have the equipment to produce it, with the possible exception of a few houses, we are able to average only about 12,000 tons, and in consequence, about 30 per cent. of our by-product ovens in the Chicago district are idle, and a number of blast furnaces are down for the want of coke. These figures, of course, refer to conditions before the strike of switchmen in April was started.

Jan 1, 1920

By Bruce A. Kennedy

If it had not been for the persistent cold wind, the sun blazing out of a cloudless blue sky would have made it one of those warm, idyllic early spring days which attract the socalled "snowbirds" to Northern Mexico for a vacation at this time of year. At a drill site perched on top of a rather exposed mountain we were installing a number of borehole extensometers in diamond drill holes. A Threading Problem For the uninitiated in geotechnical instrumentation, a borehole extensometer is a series of anchors installed at various depths in a borehole, each anchor being independently connected by a tensioned wire to a measuring device set in the collar of the hole. Any movement of the rock at depth is detected by the anchors and transmitted by the wires to the measuring device. Flexible plastic tubing is used as a spacer between the anchors and the measuring wires are run up the inside of the tube. At this particular site we were installing an instrument string nearly 1000 ft in length. Threading wire only 0.041 in. in diam through 1000 ft of plastic pipe is almost as difficult as getting the proverbial camel through the eye of a needle.

Jan 1, 1971

By Marlin D. Schutte, Graham M. Fraser, Paul M. Kubera, Ronald J. Weetman

Mixers play an important function in the operation of multi-phase reactors in the minerals processing industry. They must suspend solids, transfer oxygen, maintain pH and temperature uniformity, assist in heat transfer, and, in biological processes, avoid the development of excessive shear rates. The LIGHTNIN A315 impeller (Figure 1) effectively supersedes the older Rushton turbine (Figure 2) which has been classically employed in gas­Iiquid-solids applications such as bacterial oxidation, cyanide destruction, etc. Since a stirred tank reactor can be such a key part of the overall process, it is essential that the mixers be designed for long term reliable operation, both process and mechanical, to insure a high percentage of on-line availability. Mixers in gas-liquid-solids processes may experience extraordinary loading conditions which must be taken into account to guarantee a robust mechanical design. Given the recent trend towards the design of world-class process units with maximum capacity equipment, there is increased importance and emphasis on the integrated design of the complete agitation system -mixer, vessel, and structure -to insure trouble free, post­commissioning performance. This paper presents some of the considerations necessary to specify the process functions of the mixer in multiphase applications, as well as special considerations for the mechanical design of the integrated reactor system.

Jan 1, 1993

By P C. Hagan

Production scheduling is often reliant on an estimation of a mineÆs trucking capacity. While this mechanistic approach is relatively simple, it often over-estimates actual throughput resulting in under-utilisation of downstream process and a shortfall in revenue. An alternate approach has been developed that recognises the interdependency between processes in the mine production system including materials loading, haulage and crushing. This approach incorporates a heuristic model based on queuing theory that accounts for the variability in performance of individual processes and that this paper presents the results of a study comparing the conventional approach to mine scheduling with a capacity constrained model at a large open cut mine having a truck and shovel fleet. The capacity constrained model consistently predicted a lower material throughput compared to the conventional approach. Differences in throughput between the two approaches were found to increase with loading time, for example when loading time exceeded 3.9 minutes there was a shortfall of up to 40 per cent in estimated throughput. Longer travel times tended to ameliorate any differences. When applied to a mine schedule that extended over a two and a half year period, the difference was equivalent to a shortfall of nearly eight per cent in total material movement.

Jan 1, 2007