Search Documents

By Patzen Wu

The Hai-Shan No. 1 Coal Mine, located in northern Taiwan, is one of the typical coal mines on the island which, limited by natural condition, are mostly small in scale. With the advancing longwall method, the mine is now winning a seam, 80 cm thick, at a 32° dip, with a working depth of 824 m below surface. The annual output is about 50,000 mt of clean coal. At the working gallery, the virgin rock temperature may go up to 46°C, difficult to be brought dam to n acceptable level: because .of the tropical climate with high intake temperature and high humidity. Besides, at this depth, the intake air that goes down the long inclined shaft generates considerable heat due to autocompression. The mine is ventilated by a set of axial-flow fan with 38 m3/S of intake air at 2.2 KPA WG. With this volume of air, the temperature at the working-face is usually above 30°C WB. Appreciable lowering of the temperature is not expected even with an increased volume of ventilated air. For this reason, decision has. been made to try the installation of a pilot underground refrigeration unit near. the lowest gate road to cool the intake. air. from 32°C WB to 28°C WB which seems acceptable to on-the-spot workers exerting heavy physical labor. The experimental unit is designed for carrying away a total heat load of 90 Kw. The capacity of the unit is 200 Kw. The unit consists of a compressor, an evaporator, a condensor and a motor. The heat rejection is done in a cooling tower. Chilled water is circulated from the evaporator to the cooler by insulated pipes. The cooler consists of 90 Kw-coils with two fans and forces air by flexible ducting onto the working face. This paper examines mainly the effect of this additional reduction of working temperature, on working efficiency of the workers. Another aspect of this experiment is to evaluate the overall economy of underground refrigeration in small-sized coal mines under tropical condition. The success of such an experiment may lead to wider application of refrigeration to render many of the deeper mines economically workable.

Jan 1, 1980

By John McCoy, Edward Thimons, Kenneth Heller

As the working levels in domestic mines are developed to greater depths and work areas move further from the shafts, maintaining a safe and healthful working environment becomes more difficult. Increased temperature and humidity at greater depths becomes first a factor in productivity and then a threat to the miner's safety. Initially, a miner might develop listlessness leading to reduced productivity and reduced alertness. Continued overexertion can lead to heat stroke and possibly death. Mine ventilation engineers, therefore, must not only provide clean air to work areas, but also must provide cooled air. The following article describes the United States Bureau of Mines (USBM) and Foster-Miller's successful development of a high performance, low maintenance direct water to air contact heat exchanger for mine cooling. While heat problems frequently do not develop until mining operations descend below sea level, problems will arise any time mining penetrates high temperature rock. Hot fissure water will increase the severity of the situation, causing increases in wet bulb temperature - the temperature to which perspiring miners reject metabolic body heat. All energy expended in mining adds to the heat load which must be absorbed by the ventilation air. Just when the cooling capacity of ventilation air is needed most, adiabatic compression (autocompression) of air descending the shaft raises air temperatures 1.3g°C (2.5'F) to 2.94"C (5.3OF)/305m (1000 ft) depending on humidity. Increased temperatures decrease the ability of the air to absorb heat from the mine, and work area temperatures rise. Once forced ventilation air can no longer maintain safe work area temperatures, refrigeration methods must be employed. Many mines now use cooling coils for this purpose. A cooling coil uses refrigerated mine water to cool the air by passing the air through banks of copper tubing filled with cold water. Heat from the air is transferred to the water through the pipe with the aid of fins. Conventional water to air heat exchangers prove troublesome for many mines be- cause of the high levels of dust that are encountered, causing these exchangers to operate at relatively low efficiencies. A more satisfactory approach to work- place cooling is desired - one that offers reduced maintenance and increased cooling efficiency.

Jan 1, 1982

By Groves D. I

The Norseman-Wiluna Belt (Fig.1) is a richly mineralized (production 1900 tonnes Au), Archaean greenstone belt, up to 800km long and 200km wide, which forms the major part of the Eastern Goldfields Province within the Yilgam Block. The Belt evolved ca. 2700 Ma ago as an oblique-slip mobile belt between flanking portions of an older greenstone terrane. Volcano-sedimentary successions in the Belt represent two distinct tectono-stratigraphic associations. Sequences of metamorphosed caic-alkaline intermediate to silicic volcanic rocks interlayered with tholeiitic basalts probably represent the remains of a dissected Archaean volcanic arc (or arcs), and sequences composed dominantly of ultramafic to mafic lavas and intrusions, with minor interflow tuffaceous, sulphidic or cherty sediments are interpreted as remnants of the floor of an ensialic marginal basin (Barley and Groves, 1988). Ultramafic volcanism at Kambalda has been dated at 2692 ¦ 2 Ma (Claoue-Long et al., 1986). The dominantly volcanic associations are locally overlain by coarse clastic sedimentary succes- sions. The Belt is also typified by major north- to north-northwest-striking fault systems, shear zones, and tectonic lineaments, many of which are traceable for more than 300km. As well as defining the boundaries of the belt, these structures have accomodated much of the regional strain and acted as conduits for hydrothermal fluids during deformation, metamorphism and mineralization. As a result, most of the epigenetic gold deposits in the Belt occur in subsidiary structures related to these fault systems (Eisenlohr et al., 1988). Deformation involved oblique compression resulting in a closely spaced network of low-angle faults (thrusts) as well as upright folds and oblique- to strike-slip faults (Archibald, 1987; Veamcombe et al., 1988). This was accompanied by regional metamorphism and granitoid emplacement. At Kambalda, regional deformation and metamorphism were synchronous with the emplacement of the Kambalda Granodiorite which has been dated at 2662 ¦ 4 Ma (Hill and Compston, 1986), approximately 30 Ma after volcanism.The tectonic history and style of deformation of the Norseman-Wiluna Belt are similar to those of Phanerozoic oblique- slip mobile belts at continental margins, which are also a major source of hydrothermal gold mineralization.

Jan 1, 1988

By G. I. McPhail

The authors have conducted several investigations into the prediction of the beach profile of high-density tailings and have found that there are a number of important considerations that need to be taken into account over and above the reliability of the beach profile prediction methodology. These considerations relate to the chemistry of the slurry and specifically the influence of pH and flocculation, both of which have a significant influence on the rheology of the slurry at the discharge point. A number of examples are discussed and a potential testing protocol that will assist in assessing the influence of chemistry ahead of the beach profile predictions is presented. A methodology for assimilating the results of the testing into the likely field situation is discussed, and suggestions are made on application of the results in beach profile prediction. The suspected influence of residual flocculation on the stratification

Jan 1, 2012

By W. C. Phalen

E. G. SPILSBURY; New York, N. Y.-I would like to emphasize what Mr. Phalen says in his paper regarding the possible utilization of the waste acids in the West for the acid concentration of phosphate rock, and to call attention to the fact that this is already being done by Mr. Laist at Anaconda, who is producing concentrated phosphoric acid from these low-grade rocks. During the last year, he has not been able to carry this along to the extent he, had expected, owing to the tremendous demand which they have had for all the acid they can produce, so instead of having a. surplus of acid, as was expected, they are really short of this material for their electrolytic copper and zinc work.

Jan 4, 1917

By P. K. Naik, S. C. Das

Leaching studies of low-grade manganese ore containing 31.77% Mn and 23.71 % Fe from Nishikhal, India, were carried out using pyritiferous lignite as a reductant in sulfuric acid medium. The variables studied were quantity of lignite, sulfuric acid concentration and temperature. Regression equations for the extraction of manganese and potassium were determined from 23 full factorial design data. The experimental conditions for the extraction of manganese were optimized using the steepest-ascent method. It was found that 99.03% of the manganese could be extracted in three hours with an ore to lignite ratio of 1:1.8, a sulfuric acid concentration of 1.9 M and a temperature of 99°C. Key words: Leaching, Manganese ore, Lignite, Statistical design

Jan 1, 2003

By L. E. Eary, Andy Davis

The evolution of pit lake water quality depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock vs. oxidizable sulfide content, the alkalinity of recharging groundwater and the evapo-concentrative characteristics of the system. This paper assesses the geochemistry of 11 existing pit lakes, ranging from the acid Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits, with long-term chemistry lying on a geochemical continuum between end members that consist of influent calcium bicarbonate groundwater and naturally occurring sulfate-rich evaporite playa lakes.

Jan 1, 1998

By P. Venkatasubramanian

The aerospace and nuclear industries have been applying systematic techniques for assessing the safety of complex technical systems for many years. These techniques such as fault tree analysis, failure mode, and effect analysis, etc., and more recently "expert systems," were developed to formally evaluate systems safety and to determine how hazards can he reduced. The application of formal methods such as expert systems has the potential for further reduction in both frequency and the consequences of mine accidents. This paper presents a general expert system model of diagnostic reasoning and describes its use as an inference method for analysis and problem identification for accidents due to the presence of an open cycle diesel-powered mine cars in underground coal mines.

Jan 1, 1987

By H. B. Carroll

The Bureau of Mines investigated the adaptability of the Meteorology Research Inc.2 (MRI) nephelometer and the Sinclair-Phoenix smoke meter for use in routine, analytical, smog-chamber experiments and to compare their responses to aerosol during these experiments. Both instruments' sampling systems were modified--smaller size sample input systems were studied using the nephelometer and a secondary sample system was added to the smoke meter to allow measurement of Aitken or condensate nuclei. Both instruments were easily adapted for use with small smog chambers and both displayed good precision and sensitivity to aerosol. A correlation was shown to exist between the two instruments' responses to aerosol. This correlation makes it possible to report the Sinclair-Phoenix measurements in visibility and/or mass units if desired.

Jan 1, 1973

By P. Mottahed, J. Ran

Mining practice and research have shown that the jointed roof in stratified rock behaves like a voussoir beam structure with strength greater than that determined by the continuous beam theory. Previous studies have demonstrated the voussoir beam mechanism and developed methods to estimate the crushing and buckling strength of voussoir beams. However, research on voussoir beams with multiple mid joints has not been suffICient and problems such as the voussoir beam support and applications of the voussoir beam mechanism to the mining environment have not been addressed. In this paper, mechanism of voussoir beams containing multiple mid joints and truss support are studied and applications of the voussoir beam mechanism to underground mine openings are discussed based on the numerical and experimental results.

Jan 1, 1995

By H. W. Knott, M. H. Mueller, P. A. Beck, W. P. Chernock

PREFERRED orientation studies by Harris of rolled uranium rods indicated that hot rolling to a small reduction of area caused the (010) planes to become strongly oriented and the (110) planes weakly oriented perpendicular to the rolling direc- tion. The relative intensities of these two fiber texture components were reversed upon rolling to higher reductions of area. Cold rolling caused the (010) planes to become strongly aligned and the (130) planes weakly aligned perpendicularly to the rolling direction. The present investigation was undertaken to explore in more detail the effect on the rolling texture of variables, such as the penultimate condition, the final rolling temperature and reduction of area. In addition, the recrystallization texture of rolled uranium rods was also investigated.

Jan 1, 1959

By R H. Yoon, M Gupta, A Noble, K Huang

Froth flotation is the most commonly used separation technology in the mineral industries. Given the complexity of the pulp and froth phases as well as the multitude of operational parameters that influence flotation performance, purely fundamental models with strong predictive capacity are limited. As a result, accurately modelling modifications to an existing flotation circuit are challenging, particularly when using empirically-derived models from a different operating configuration. Despite these complexities, a recent publication by the authors (Huang et al, 2022) has shown that flotation rates can be accurately predicted from a first-principles model that incorporates hydrodynamic parameters (eg pulp density, superficial gas velocity, feed flow rates etc), surface chemistry parameters (eg contact angle, zeta potentials and surface tension), and size-by-class liberation data. Circuit simulations using this model were shown to be effective in predicting experimental graderecovery curves from the size-by-class mineral liberation matrix. Since the model is derived from fundamental characteristics of the flotation system, it can be used to simulate alternative circuit configurations with varying degrees of recycle. Conventional flotation circuits are operated in a closed-circuit configuration by routing the cleaner scavenger tails (CST) back to the rougher feed to provide an additional opportunity to recover the slow-floating particles. This widely-used flotation strategy has been under constant debate, and several researchers have provided evidence that open circuit configurations provide higher separation and better circuit control (Konigsman, 1985; Bulatovic et al, 1998; Thompson, 2016). Recently, Finch and Tan (2021), used linear circuit analysis to show that open circuit configurations have a fundamental advantage when stage recoveries are high. Given the limitations of these prior studies, the objective of the current work is to further evaluate the merits of the open circuit configuration through a detailed circuit analysis and simulation study incorporating the first principles model described above.

Aug 24, 2022

By W. A. Young

To initiate this project a critical evaluation of the pre-sent phosphate mining industry in the Western phosphate field was conducted. Mines were visited, mine operators were interviewed and pertinent literature studied. Three phosphate mining enterprises were reviewed and mining cost estimates prepared. The report discusses the present state of phosphate processing, rock alteration and location. New ideas and concepts are proposed to improve the recovery of phosphate rock from the Phosphoria formation. The report evaluates two variations to the present phosphate open pit mining methods, which were developed to improve the economics of mining phosphate and to better accomplish necessary reclamation and accelerate the time for environmental recovery. A material handling system using conveyor haulage will eliminate the need for trucks. Terrace haulback utilizes safety benches to haul and dispose of waste in the mined out pit. Ore will be removed from the pit via an inclined, cable-supported mobile conveyor.

Jan 1, 1980

By Richard J. Mainiero

The Bureau of Mines investigated coal-mine-type short-delay electric detonators marketed by three domestic manufacturers to determine the accuracy of delays and the probability of overlap between adjacent de- lay periods. The Winzer index was computed and compared with the probability of overlap. A close agreement between the Winzer criterion and overlap probability was demonstrated. A permissible blasting unit capable of delivering a maximum firing energy of 4.0 J and a digital oscilloscope were used to measure the delay time with an accuracy of 20.25 ms. Another oscilloscope and a pulse transformer were used to record firing current. Experimental data indicated negligible overlap probability in detonators of shorter delay periods: periods 1 to 4, which correspond to 25 to 250 ms. However, a significant probability of overlap was detected in some detonators of longer delay periods: periods 5 to 9, which cor- respond to 300 to 500 ms.

Jan 1, 1985

A Modelling Approach Using a Back-Calculated Induction Time to Predict Recoveries in Flotation

Sep 13, 2010

By E. W. Enqelmann

INCREASED metal consumption throughout the world in the past three years has brought greater activity in the concentrators and mills that treat the ores.' Comparatively low prices have made greater economies necessary, with a continuing search for more efficient flow sheets, equipment, processes, and reagents. Comminution GRINDING has long been too ex- pensive and even any small increment of saving has been eagerly sought. Although not recently new the use of rod mills to cover the gap between intermediate crushing and coarse grinding has made further headway. They eliminate dusting and the closed- circuit operation of fine crushers, either roll or Symons cone, and the rod-mill product is suitable for secondary mills which can be operated with smaller balls and iron liners instead of coarse balls and steel liners. The newer practice is radically different from the older application of rod mills where they at- tempted to use them instead of ball mills for fine grinders. For that purpose they were not well adapted, as they do not have sufficient grinding surface available per cubic foot of mill volume.

Jan 1, 1940

By F. Qian

Direct impingement of molten metal baths by a gas jet is commonly encountered in such processes as BOF and electric arc furnace steelmaking. Shape and local fluid mechanics in the impinging region is important because it determines the interaction of the metal pool with the surroundings. Goal of the present work is to characterize and understand the interfaces at the impinging region. Using a physical model consisting of water/corn oil and water/kerosene as surrogates for metal/slag, interface shapes for slag-gas, slag-metal and metal-gas are investigated. Influence of transport properties of the two liquids on the shape and flow fields are also experimentally determined under various impinging jet conditions, namely jet momentum and jet height. The viscosity of the slag layer (corn oil or kerosene) has the most significant effect on the interface shape and the induced flow fields. The interface shapes were measured both photographically and by using a surface- tracking resistance probe. The limiting condition at which the jet breaks through the corn oil or kerosene layer and reaches the water layer was determined experimentally

Jan 1, 1994

By S. S. Peng

High horizontal stress has been well recognized as a significant factor in roof control. It can adversely affect roof stability if the panel is designed improperly. Mining experience has shown that it can cause a cutter roof. The effects of high horizontal stress on roof stability depend on many factors such as magnitude and direction of the maximum principal horizontal stress, ratio of the maximum to minimum principal horizontal stress, structure and mechanical properties of the immediate roof and mining sequence. However, little is known about the intrinsic mechanism of high horizontal stress effect on roof stability except some conceptual explanations. In order to design a stable entry, the redistribution and concentration of high horizontal stress around the openings must be fully understood. Using the 3-D finite element analysis technique, this paper presents the redistribution and concentration of high horizontal stress field for a three-entry system with different orientations of horizontal stress. Based on the horizontal stress redistribution, possible roof failure for different orientations of horizontal stress is analyzed.

Jan 1, 1996

By C. A. Komar

Laboratory-scale hydraulic fracture tests were conducted by the Bureau of Mines on directionally oriented sandstone material, along with measurements of directional rock properties such as tensile strength, permeability, ultrasonic velocity, and dynamic elastic constants. In these tests, fracture orientation was determined as a function of various combinations of stress, rock saturation, rate of borehole pressurization, and direction of minimum tensile strength relative to minimum horizontal compressive stress. The objective of the experiment was to investigate whether horizontal stresses always controlled the orientation of induced vertical hydraulic fractures, or if under conditions of small differences in stress and/or slow borehole pressurization rates, the induced fracture direction was influenced by directional properties of the rock matrix. This study shows that the expected influence of horizontal earth stress on the orientation of an induced hydraulic fracture becomes negligible when¬ever the magnitude of the difference between the compressive stresses is 200 psi or less. When this occurs, fracture orientation is controlled by the directional properties of the rock--primarily permeability and tensile strength.

Jan 1, 1973

By John F. Abel

At the spring meeting of the Open Pit Division of AIME's Arizona Section, I was asked a question which indicates the acceleration of technical advancement. The question was: "How does an engineer at a properly keep abreast of what is new?" The fact that some 200 Arizona AIME members were at the meeting is a testimonial to the desire of these men to do just that- keep abreast. There is a great deal of talk in academic circles about the built-in obsolescence of an engineering or scientific education, too. About 100 commencement speakers every spring are sure to admonish the graduates that education is a continuing thing. Mining engineers are a small fraternity. We keep informed by talking to one another. Talking shop is valuable but there is no substitute for reading.

Jan 1, 1970