Search Documents

By C M. Hill

This paper aims to provide a brief overview of the Australian Coal Bed Methane (CBM) industry and more importantly the challenges to sustainable management of the industryÆs by-product, groundwater. In a country where water is scarce and having gone through one of the worst recorded droughts it is vital that this important industry be seen to be managing water in a responsible manner with the greatest environmental and social benefit. Benefits of the water from CBM wells can be enhanced through treatment to produce potable water for domestic or stock purposes, water for irrigation or aquaculture or lower quality or untreated water for industrial or mining purposes. Other options are re-injection of raw water or waste from the treatment processes or discharge to surface waterways. The critical change and difference between CBM projects and traditional oil and gas operations should be that where possible water is no longer disposed of via evaporation ponds with the dual legacy of waste of the water resource and an environmental contamination problem with the remaining salt and brine product.

Jan 1, 2003

By F. J. Smith, W. A. Gallagher, C. A. Herbert

"INTRODUCTION A fire started about 10 a.m., November 10, 1947, at the Kings mine, Princeton Mining Co., Princeton, Ind., about 1,800 feet inby the main shaft bottom on the main west haulage road at a point estimated to be 2 miles from the faces of the main west entries. No lives were lost, as 27 men escaped from the mine after a series of explosions, which necessitated sealing the mine on the surface. This information circular shows"" how adverse conditions might be overcome, when reopening a sealed mine, by expert planning and close cooperation on the part of various organizations. Conditions found in the mine after it was reopened were comparable to the worst that had been anticipated, yet the mine was recovered with comparatively little difficulty and a minimum of risk. The open workings in the mine covered a vast area, but most of the mine resumed production of coal after being sealed for only 37 days.The information contained herein also points to the desirability of adhering as closely as possible to a predetermined schedule of operations."

Feb 1, 1949

By Z. T. Mathe, M. A. Vera, M. C. Harris

This contribution presents a methodology how to quantify froth zone recovery in a continuously operated laboratory mechanical flotation cell. The methodology consists of relating the overall flotation rate constant to the froth depth of the flotation cell. As a result, a froth zone recovery factor (Rf) can be extracted. This froth performance parameter has been studied as a function of the flotation cell operating variables. By understanding the effect of these operating variables on Rf, an integrated methodology for modelling froth zone performance in batch and continuously operated laboratory flotation cells has been proposed. The Rf modelling is based on a semi-empirical approach which considers a number of parameters to be used. Some of these parameters may have physical significance, i. e. they may be easily and physically measured. The modelling approach consists of taking into account the interaction between the pulp and froth zones. This interaction allows froth zone recovery (Rf) to be predicted. The whole modelling exercise process lies on auxiliaries relationships which indicate the dependence of the parameters with the operating conditions of the flotation cell. This contribution is part of a larger project that deals with the modelling and optimisation of flotation plants (Project P9L, 2000).

Jan 1, 2001

By G. H. Lewis, C. L. Krcil, N. S. Harding, D. E. Havekotte

Introduction Limestone injection work was completed in a 440-kW (1.5-million Btu per hour) pilot-scale combustor in preparation for a 50,000-kg/h (110,000-lb per hour) industrial steam boiler limestone injection test program. The main objectives were to: (1) identify the important variables that affect sulfur capture, (2) determine the maximum SO2 removal, and (3) determine the effect of limestone addition on furnace operability and heat transfer. A more detailed report is given by Lewis et al. (1985). The test program was divided into two phases. The objectives of Phase I were to determine the important variables that affect SO2 reduction and to investigate the effect of limestone addition on combustor operation and heat transfer surfaces. The objective of Phase II was to determine, using only the important variables identified during Phase I, the conditions that resulted in the greatest sulfur dioxide reduction. Phase I Test program Using one limestone, five variables were identified as having an effect on SO2 reduction. These are noted with their respective ranges: heat release rate [103 to 166 kW/m3 (10,000 to 16,000 Btu per hour-cu ft)], Ca/S molar ratio (0 to 3), flue gas oxygen concentration (3% to 5%), additive particle size [90% -150 µm (-100 mesh) and 90% -45 µm (-325 mesh)], and burner stoichiometry (SR = 0.75 and >1.15). A 2.3% sulfur northern West Virginia coal, pulverized to a nominal grind of 70% -75 µm (-200 mesh), was burned for the tests. The limestone used was obtained from a Maysville, KY, quarry and contained 51.75% (wt) CaO. An 11-run statistically designed program (plus three duplicates) was used to screen the five variables. The effect of limestone injection on the combustor heat transfer surfaces was determined by comparing the heat transfer rates through a slag panel and fouling probes during periods with and without limestone injection. Combustor operation was determined by noting any operating problems that occurred during the tests. Test procedure After furnace wall temperatures had stabilized at operating conditions, heat transfer surfaces (slag panel and fouling probes) and the convection section were blown clean, and a four-hour test was begun. The

Jan 12, 1986

By H. S. Chang

A three-dimension two-phase (air and dust) computer model was developed to model air velocity and respirable dust distributions in the longwall faces. This paper describes the derivation of the model including the model features, mathematical equations and boundary conditions. Example simulations were also performed for two longwall faces where measured respirable dust and air velocity distributions were available. The results indicated the model can simulate the mine conditions fairly accurately.

Jan 1, 1996

By Lucas Nana Wiredu Damoah, Lifeng Zhang

"Increasing demand for Solar Grade Silicon (SoG-Si) due to rising interest in renewable energy has lead to increased SoG-Si Top – cut scraps generated from the multi-crystalline silicon making process. Due to the high cost of SoG-Si and the potential to use the top-cut scraps as feedstock material, there has been increased effort to develop cost effective and efficient technologies. As a result, several methods to recycle the top-cut scraps are currently been applied, and researched. These include settling under gravitation field, which is a slow process to be industrially applicable. Natural settling of inclusions by gravitational force is a slow process and not attractive to the industry. Recent experiments on Top-cut SoG-Si scrap under high frequency, high voltage, electromagnetic field showed that SiC inclusions settled within a short time to the bottom of the crucible and the characteristic rod-like morphologies of Si3N4 inclusions in SoG-Si were not detected. This study investigates the enhanced settling of SiC inclusions and the behavior of Si3N4 particles under the influence of high frequency, high voltage, electromagnetic field in Top-cut SoG-Si.IntroductionThe photovoltaic industry depends on silicon based PV materials either as single-crystalline silicon, or multi-crystalline Si (MC-Si), or amorphous Si [1] for over 90 % of its market share. [2] MC-Si produced by directional solidification of solar grade silicon melt dominates the silicon PV market. During the directional solidification process, SiC and Si3N4 particles within the melt are pushed by the solidification front to the top of the ingot which is the last to solidify. Therefore the top of the ingot is cut generating what is known as top-cut solar silicon scraps. The Si3N4 particles are mainly from the coating material at the inside surface of the silica crucible and from air absorption during the solidification process. The SiC particles mainly stem from the carbon reduction process of the primary production of silicon [3]. Due to the growth of the PV industry as a result of global demand for clean, reliable, and affordable energy [4], there is the need to develop new methods to compliment exiting ones to recycle SoG-Si waste (e.g. top-cut) for sustainability."

Jan 1, 2012

Mining Impact in Water Quality: Understanding the conflict Mining is an industrial process Metal mines that chemically process ore to concentrate metals such as copper and gold use more water than non-metal mines such as coal, salt and gravel. Tailing Ponds Water contaminated with high concentrations of metals, sulphide minerals, dissolved solids, or salts can negatively affect surface water quality, aquatic ecosystems and groundwater quality.

May 1, 2013

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils rind 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Figure 1 shows this building, market; "Main high school building?, with respect to other buildings, pipe lines, oil wells, and gas lines on the property.

Jan 1, 1937

By R. H. Snow

Although industrial size reduction methods have an energy efficiency of only about 1 percent, methods of size reduction have not changed much for many years. One reason for slow progress has been the oversimple viewpoint that a single law should exist to relate size reduction to energy input. Modern simulation methods decompose the grinding process into a grinding rate function (selection function) and a breakage function. The breakage function is difficult to measure, and it usually requires tracers if it is determined from milling experiments. Prediction of breakage functions from basic principles is one objective of this paper. In this study we focus attention not on the gross energy input to the experiment, but on the spatial distribution of stress energy within the particle. We are led to this viewpoint by experimental observations of a few previous investigators (Bergstrom2, Rumpf3, Axelson4) and our own observations. Oka and Hiramatsu recently used their calculations of stress within particles for prediction of breakage, but again they tried to correlate the size of the fragments with the total stress energy, rather than the approach we propose. We assume that the stress energy is stored in the interior of the particle as the load is increased, until the particle breaks. We assume that each element of the particle breaks into fragments of a mean size that depends on the locally-stored stress energy. The size distribution of fragments is the computed from maps of the stress-

Jan 1, 1972

By Yoji Imai, Akio Watanabe, Masakazu Mukaida

"To clarify the feasibility of alkoxides and acetylacetonates as precursors for laser CVD of metal oxides, vapors of tantalum or titanium alkoxides and zirconium acetylacetonate were irradiated by KrF excimer laser and deposits were characterized by XRD and XPS measurements. As for tantalum and titanium, non-stoichiometric crystalline oxides grew nearly phototropically, however, zirconium oxides deposited showed only halo-pattern by XRD measurements. Electric conductivity measurements of tantalum oxides implied the improvement of the insulating properties by the addition of activated oxygen to the ambient.IntroductionThere has been renewed increasing attention to the metallic oxide thin films because ofits promising usefulness in many applications, such as high-Tc superconductors and ferroelectric devices. A variety of thin film preparation techniques have been studied such as sputtering, chemical liquid deposition (sol-gel and metalorganic decomposition), pulsed laser deposition and chemical vapor deposition (CVD). Among them, we think CVD is the most promising method because it offers a high controllability of morphology and good step coverage at relatively high growth rate. Preparation of oxide films by CVD can be achieved using a precursor containing metallic element and oxygen containing gas such as N20 at the same time. However, metalorganic (MO) compounds which contain both metallic element and oxygen, directly bonded to metallic element, seems to be more favorable because some of MO has a good properties for CVD such as a rather high vapor pressure, stability in ambient and low toxicity."

Jan 1, 1998

By Wenquan Zhang

Based on the mining and geological conditions of Wadong Mine, Longkou City, Shandong Province, China, a viscoelastic model with proper creep parameters was established. The 3-D ANSYS was used to simulate surface subsidence, analyze overburden subsidence characteristics, and propose the rational mining and pillar widths for mining in weak rocks and under special mining conditions, and provide the policy makers scientific data for decision making on mining activities.

Jan 1, 2006

By J. Petersen, K. Shaik1, H. Kolev, Z. Cherkezova-Zheleva

Sperrylite is one of the most abundant platinum minerals globally, valued for its economic importance but also known for its highly refractory nature, making it difficult to process via the conventional route. This study explores the oxidative leaching of sperrylite using a cyanide–ferricyanide system, with a key focus on characterisation of the mineral and surface speciation under varied leaching conditions using x-ray photoelectron spectroscopy. The parameters investigated include the effect of sodium cyanide concentration, the use of potassium ferricyanide as an oxidant, copper sulphate pentahydrate as a catalyst, as well as the effects of temperature and particle size. A limited set of leaching tests was carried out to study the surface chemistry rather than optimising dissolution conditions. This approach identified mineral oxidation states and shifts in binding energies, prior to and post leaching. XPS analysis of sperrylite’s surface chemistry identified key species, comprising the bulk Pt(II)–As (≈73 eV) and As(–I)–Pt (≈41.8 eV) states, together with surface oxidation products Pt(II)–O (≈72 eV), Pt(IV)–O (≈74.5 eV), As(III)–O (≈43 eV) and As(V)–O (44.5 eV). Leaching led to the removal of pre-existing oxides on the ultra-finely ground sample, exposing the underlying bulk species. In contrast, the crystalline sample with an initial low concentration of oxides, generated higher amounts of fully oxidised species after leaching, reflecting greater surface reactivity.

Mar 6, 2026

By I. D. Wood

The geostatistical methods given for the estimation of low-ash coal reserves take into account the geological structure of the seam, and consequently give far more reliable results than have been obtained in the past. Confidence limits are given for all the estimates.

Jan 1, 1979

Why innovate? ? How are we doing in Canada? ? How can we do better? ? Why now? ? What?s next? ? Lowering production costs ? Improving productivity ? Increasing value-added ? Discovering new mines, extending life of existing ore bodies ? Reducing environmental footprint ? Improving health and safety

May 1, 2008

By Babak Mamaqani, Pirooz Barar

The Heights project was located at Fashion Valley North, San Diego, CA. The scope of the project was to replace two existing commercial buildings with a large 7-story multi-family residential building. There was an existing 1:1 slope on the north side of the site. A permanent soil nail wall, 1,000 linear ft long, with a maximum height of 100 ft, was needed to replace the 1:1 slope at the north side of the project to accommodate the development. Previously there was a design for the permanent soil nail wall which required up to 115 ft long soil nails with large diameter rebars and 13 in. thick permanent facing. PB&A was engaged by the owner to conduct soil nail design optimization and value engineering to reduce construction costs and improve scheduling. First, the SnailPlus program was used to check the stability under static and seismic conditions and to design soil nail lengths and sizes. Then, soil nail head forces were calculated to design the permanent facing using FHWA recommended procedure. Another challenge of the project was to evaluate the interaction between a future San Diego Gas and Electric (SDG&E) tower and the soil nail wall. Finite element analyses were conducted with the PLAXIS program to ensure the deflection of the future tower would be within the acceptable range. The soil nail design optimization helped the owner to save approximately $800,000 in construction cost and improved construction scheduling.

Sep 8, 2021

By Richard Kolada

If the emission of methane into any particular area of an underground coal mine remains constant, then the calculation of ventilation requirements is relatively simple. This is also true if the ventilation system is recirculatory. However, the emission of methane into a working area can vary considerably. There is always a risk that the ventilation will not be able to dilute the emission of methane to acceptable levels, because there are often short-lived peaks of emission which are very large. The ventilation design must therefore consider what is an acceptable level of risks and calculate the airflow requirements to meet this level. The acceptable level of risk can be calculated by examining the historical variation in methane emission into the area to be ventilated. For example, consider that an acceptable level occurs when methane emission peaks only exceed the capability of the ventilation one day in twenty. Then, from the history of methane emission, it is possible to calculate the necessary ventilation requirements. This method has been used since the early 1980s for conventionally ventilated districts. This paper examines the application of this technique to districts ventilated by recirculatory ventilation.

Jan 1, 1987

By C. Sachanidis

From the surface mines of Ptolemais basin 48 samples of Pliocene lignite were collected. The samples were analysed using Instrumental Neutron Activation Analysis (INNA) and Inductively Coupled Plasma (ICP) for determining the concentrations of 39 trace elements. The contents of sulphur and ash and the loss of ignition were also determined. The chemical affinity of these trace elements was estimated based on 40 correlation diagrams between the elements concentrations and the ash content of the collected lignite samples. According to the obtained results, 18 elements have inorganic affinity (Co, Cr, Cs, Hf, Sc, Th, La, Ce, Nd, Sm, Eu, Yb, Lu, ?n, Ba, ?, Sn, ?r) and 10 elements have inter-mediate affinity (As, U, ?r, Pb, Cu, Sb, Sr, S, Ni, V). The remaining 12 elements (Au, Ir, ??, Rb, Se, Ta, W, Tb, Ag, Cd, Bi, Be) exhibited concentrations below the detection limit. Thus, they were impossible to be classified in a specific affinity group. Based on the classification of these trace elements and sulphur in inorganic and intermediate affinity groups some useful conclusions are drawn regarding their behaviour during lignite combustion and lignite ash utilization and disposal processes.

Jan 1, 2006

By T. P. Harrington, P. G. Doctor, K. A. Prisbrey

Crushing and grinding ore consumes so much energy that it represents a major component of total processing costs. While it has been estimated that only about 0.6% of the total energy expended in grinding is actually used to create new surfaces, accurate measurement of this quantity is difficult. If energy expended in crushing and grinding could be more directly measured, alternatives for increasing efficiency of the processes could be evaluated more effectively. Since the energy intensity associated with rock fracture is related to fracture sonority, it should be possible to use this sound (acoustic emission) to measure the actual energy expended. However, it is difficult to apply this approach because the mill environment is so noisy. To make the approach practical, a method for differentiating acoustic emissions caused by rock fracture from those caused by extraneous noises must be found. Pattern recognition analysis may provide such a method. This paper presents the results of pattern recognition analysis to make two types of differentiations: acoustic emissions caused by crushing two types of minerals (quartz and chrysocolla) and those caused by two extraneous noise sources, and acoustic emissions produced by each mineral.

Jan 1, 1982

Valuers will often intuitively express the probability that property value will exceed a certain amount . . . 'I think the chances that the value will exceed $50 million are excellent. The chances that they will exceed $80 million are poor'. This paper shows how it is possible to combine the uncertainties of the value of several key items to provide an estimate of the probability of a certain overall value being achieved. The valuation of a large copper/gold deposit was naturally influenced by uncertainties in the base assumptions of costs and metal prices. Potential acquisition of the property through share purchase raised the issue of what was a reasonable intrinsic value for the shares. Market considerations could be used to appropriately adjust the intrinsic value. After a range of possible metal prices and operating costs were determined, estimates were made of their probable distributions. By combining these probabilities in a random selection, a range of property values was calculated. Each value had its respective probability of occurrence. This allowed a most likely value of shares to be calculated. This paper demonstrates how the valuer's intuition is complemented by numerical analysis.

Jan 1, 1994

By J. R. Koehler

The failure of yield pillar-based gate mad designs to provide adequate ground control performance is primarily related to the use of "critically" sized chain pillars. A "critical" pillar is one that falls into a range of pillar sizes that are too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but are too small to support full longwall abutment loads. To directly compare the in-mine performance of critical and yielding pillar designs, the U.S. Bureau of Mines recently completed a field study in a tapering gate road at the Sunnyside No. 1 Mine, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m-wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 10.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset. suggesting a properly functioning yield pillar design.

Jan 1, 1995